Set Of Mounting Parts For Rlnd (Kron-Yn (Ra-5 3 Pcs., Ra-2 1 Pc., Ra-1 1 Pc.), Clamp X7-3 Pcs., Shaft Ra-3 2 Pcs.). Gost R 52726-2007., Polymer Insulator Lk 70/10 – I – 3 Ss. Designed For Fastening And Insulating Uninsulated And Insulated Wires Of Type Sip-3 Ac Overhead Lines With Voltage 10-20 Kv, Frequency Up To 100 Hz. Climatic Modification And Placement Category Uhl 1 According To Gost 15150. End Type Design (Eyelet/Eyelet), Insulator Class Kn/Kv -10/70, Construction Height No More Than 275 Mm, Insulation Height No Less Than 185 Mm, Creepage Distance No Less Than 360 Mm, Load Impulse Test Voltage 145 Kv, 50 Hz In Dry Condition 70, 50 Hz In The Rain - 45, Discharge Voltage 50 Hz In A Polluted And Wet State Of At Least 13 Kv, Specific Surface Conductivity Of The Contamination Layer Normalized By The Pue Is 20 Μs, Permissible Degree Of Pollution (Sd) According To The Pue - 3. Weight No More Than 0.95 Kg., Cap K7. The Inner Diameter Of The Pin Is 22 Mm, The Outer Diameter Is 31.5 Mm, The Height Is 35.9 Mm, Bending Force (Perpendicular To The Axis) Is 3.5 Kn (350 Kgf), Bending Force (Along The Axis) Is 0.735 Kn (75 Kgf). Gost 18381-80., The Rlnd-10/400 Disconnector Is A High-Voltage Outdoor Circuit Breaker For 10 Kv Networks, Operating At A Rated Current Of 400 A. Its Main Characteristics Include The Highest Operating Voltage Of 12 Kv, A Thermal Withstand Current Of 10 Ka And An Electrodynamic Withstand Current Of 25 Ka. Gost R 52726-2007., Switch Bpv 4 400A. Designed For Manual Direct Or Remote Closing, Opening Or Switching Of Electrical Circuits. Performed For Currents From 100A And Above. Separate Series, Mainly Direct Current, Are Produced For Currents Up To 10 Ka. Switches Are Also Manufactured For Low Currents: 5-10A (Moving And Fixed Contacts Of The Base Are Made Of Electrical Copper Grade M1). Gost 15150., K9 Cap. Pin Diameter – 24 Mm. Weight – 20 G. Gost 18381-80, Insulator Shf – 20G1. Porcelain Pin Insulators Шф - 20Г1 Are Intended For Insulation And Fastening Of Insulated Wires Sip - 3. Rated Voltage, Kv - 20 Minimum Mechanical Breaking Load, Kn - 13, Creepage Distance - 400 Mm. Withstand Voltage 50 Hz (In The Rain), Kv – 65. Withstand Impulse Voltage 1.2/50, Kv – 135. Withstand Voltage In Dry Condition, Kv – 85 Weight, Kg. – 3.8. Gost 1232-93., Automatic Connecting Clamp Cil 2. Used For Connecting Bare Conductors. Automatic Connection Clamps Are Reliable And Easy To Install Without The Use Of Additional Tools. Characteristics And Description: • Clamp Type - Connecting, Automatic Connecting Clamp, Wire Cross-Section, Mm2: 70-95, Wire Diameter, Mm: 9.3-11.7. Gost R 70352-2022., Eyelet U1–7–16. Breaking Load Of At Least 70 Kn (7 Tons), Weight 0.62-2.67 Kg, Overall Dimensions 123 * 58 * 52 Mm, Material Steel Alloy, Thermal Diffusion Galvanizing Coating. Tu 3449-111-00111120-95., Tip A–70–12. Aluminum Cable Lugs, Secured By Crimping, Are Intended For Terminating Wires And Cables With Aluminum Conductors With A Cross-Section Of 70 Mm2. The Tips Are Made Of Aluminum Pipe. Gost 9581-80., Bushing Insulator Ipu 10/630 7.5 Uhl1. Rated Voltage - 10 Kv, Rated Current - 630 A, Lightning Impulse Test Voltage - 80 Kv, Minimum Destructive Bending Force - 7.5, Creepage Length - 300 Mm, Weight - 8.5 Kg. Gost 15150-69., Fuse-Switch Block Bpv-2 250A With Pn-2. Designed For Infrequent Switching On And Off, As Well As For Protecting Electrical Networks And Receivers From Unacceptable Long-Term Overloads And Short Circuit Currents. The Boxes Are Used In Electrical Installations Of Both Alternating And Direct Current (Moving And Fixed Contacts Of The Base Are Made Of Electrical Copper, Grade M1). Gost 15150., Die Clamp Pa - 2 - 2. The Three-Bolt Connection Clamp Pa-2-2 Is Used For Connecting Aluminum And Steel-Aluminum Wires Of Grades A70, Ac50/8, Ac70/11, As Well As Protected Sip-3 Wires With A Cross-Section Of 50, 70 Mm2 In Cables Of Overhead Line Anchor Supports And Making Taps. Characteristics: • Wire Diameter, Mm: 9.6-11.4 • Size A, Mm: 30 • Size B, Mm: 46 • Size D, Mm:: 12 • Size H, Mm: 46 • Size L, Mm: 82 • Weight, Kg: 0.20. Gost 4261-82., Anchor Clamp Dn-70 Rpi Is Used For Anchoring Protected Sip-3 Wires To Tension Insulators On End And Corner Supports. Section, 50-70 Mm2. Ultimate Load, 2000 Dan. Core Diameter According To Insulation, 12-15 Mm. Weight, 438 G. Gost 13276-79.
