Tenders Are Invited For Reconstruction Of The Agricultural Transport Bridge On The Watercourse On Plot No. 427 On The Municipal Road On Plot No. 361, No. 435 At Km 1+350 In Domaszków In The Design And Build System
Tenders Are Invited For Reconstruction Of The Agricultural Transport Bridge On The Watercourse On Plot No. 427 On The Municipal Road On Plot No. 361, No. 435 At Km 1+350 In Domaszków In The Design And Build System
1. The Subject Of The Order Is The Implementation Of The Following Investment In The Design And Build System: Reconstruction Of The Agricultural Transport Bridge On The Watercourse On Plot No. 427 On The Municipal Road On Plot No. 361, No. 435 At Km 1+350 In Domaszków.2. The Subject Of The Order Is The Design And Execution Of Works And Includes: Access To The Facility1. Earthworks In The Scope Of Channeling The Road Structure, Demolition Of The Existing And Reconstruction Of Access Roads To The Facility, 10 M Long On Each Side.2. It Is Planned To Dig An Excavation To The Level Of The Watercourse Over A Length Of Min. 4 M, In A Way That Allows Free Access To The Abutments. The Embankment Should Be Made As An Engineering Backfill Made Of Gravel (Or Other Material Meeting The Standard Conditions) And Compacted To A Value Of Id>0.97. The Scope Of Works Is Indicated In The Drawing Part.3. Construction Of The Abutment Cover From Non-Cohesive Material Of The Sand Type, Compacted To Id = 0.97.4. Construction Of Access Surfaces From Crushed Aggregate 0/31.5 Mm, Mechanically Stabilized, Thickness. 30Cm. Abutments: 1. Reinforcing The Existing Concrete Rings. By Installing Steel Bands (Clamps) Made Of Flat Bars With Cross-Section Dimensions Of 100X40mm, Fastened With Tensioning Bolts Of Class Min. 8.8 Type Sb Tzn - M20x90, Hot-Dip Galvanized. The Flat Bar Is Made Of S235 Steel With Anti-Corrosion Paint (2 Coats Of Painting). Make 2 Levels Of Clamps At 1/3 And 2/3 Of The Height Of Each Concrete Ring.2. Glue Cracks And Cracks In Concrete Rings Using Epoxy Resin Injections.3. For The Western Pillar (Slope From The Lower Water Side) Of The Northern Abutment, Which Does Not Ensure Proper Support Of The Crossbeam On The Support, Raise It Using A Prefabricated Concrete Cover. To Properly Fill And Level The Space Between The Pillar And The Concrete Cover, Use Spacers Made Of Galvanized Steel Sheets. 4. Behind The Abutment On A Bench Made Of C12/15 Class Concrete Base, Thickness. Min. 15 Cm Along The Span Width, Make A Retaining Wall Of Gabions In Accordance With The Drawing. Fill The Space Between The Retaining Wall And The Span With A Polystyrene Insert. Gabion Baskets Should Be Made As Cages With Transverse Dimensions Of 0.5 X 0.5 M, Made Of Wire Ø Min. 4.8Mm Hot-Dip Galvanized. It Is Possible To Make Cages With Other Dimension Modules. Retaining Wall Height Min. 1.5 M (The Final Height Of The Retaining Wall Will Be Determined By The Contractor In The Design Documentation)5. Protect The Base Of The Wall Against Washing Away With Reinforcements Made Of Field Stone And Cement-Sand Mortar. Make A Concrete Cap On The Upper Surface Of The Wall. 15Cm Made Of C16/20 Class Concrete. Span: 1. Verify The Position Of The Span In Relation To The Abutments (Axiality And Perpendicularity) And Correct Its Setting Using Hydraulic Cylinders Or A Crane.2. Clean The Span Using An Abrasive Blast Method, Especially Its Bottom.3. Repair Defects And Concrete Surfaces Using Pcc System Mo
We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.
