Quotation are invited for Grease;Lm/2 Nlgi No 2;5kg Delivery Date: 2026/02/18 Delivery To: Logistics - Ndabeni Store Paints & Oils PH: 021 444 5451 Delivery Address: 02 25 Oude Molen Road, Ndabeni Closing Date: 2026/02/12 Closing Time: 04:00 PM Description: 40 each x grease;lm/2 nlgi no 2;5kg Specification: * GREASE - TYPE: LM/2M NLGI 2; PACKAGING: 5Kg Tin; SPECIFIC USE: Wheel Bearings; SPECIFICATION: 1. This specification covers for the supply of three grades of high quality multipurpose greases as follows: LM/2 - No. 2 NLGI Consistency for wheel bearings of disk braked vehicles, [note the temperature range of -10 oC to 150 oC, intermittent 200 oC], industrial anti-friction bearings, centralised lubrication and general applications LM/3 - No. 3 NLGI Consistency for vertical shaft electric motors, industrial anti-friction bearings and general applications. LM/2M - No. 2 NLGI Consistency containing not less than 3% Molybdenum Disulphide (m/m) and an EP additive for low speed heavily loaded rolling element bearings, components subjected to either oscillating or rotating motion, chassis points, bucket pins, bushes, linkages, etc. 2. The oils shall be formulated from high quality HVI paraffinic base oils, blended from virgin base stock and containing suitable additives. Samples taken from any portion of the supply shall be free from impurities. No reclaimed oils are to be used. 3. The LM/2, LM/3 and LM/2M greases offered shall meet the following requirements: 3.1 General: CHARACTERISTIC PROPERTY:GREASEE CATEGORY LM/2,LM/3,LM/2M, Application Wheel bearings of disk braked vehicles, industrial anti-friction bearings and general applications Vertical shaft electric motors, industrial anti- friction bearings and general applications For earthmoving and other off-road equipment, high load, low speed rolling element bearings, chassis lubrication, pin and bush assemblies and other boundary lube applications Base oil viscosity at 40oC in mm2/s (ASTM D 445) 150min 150min 400min, Base oil type Mineral Thickener Soap, Soap type:lithium complex or mixed lithium/ calcium lithium complex or mixed lithium/ calcium lithium complex or mixed lithium/ calcium NLGI consistency 2, 3, 2, Worked penetration 1/10mm (ASTM 217) 265-295 220-250 265-295,Solid lubricant None Molybdenum, Disulphide Timken OK Load in kg (ASTM D2509)20min, 20min, 20min EP additive Yes Yes Yes. Oxidation additive Yes Yes Yes, Rust inhibited Yes, Yes, Yes,Temperature operating range (Cont)-10 to 150oC (200 intermittent) -10 to 120 oC-10 to 150 oC,Drop point (ASTM D2265) 180min, 180min, 240 min. . CLAUSE - 2.14.1 & 2.15 Provide, on request by the CCT, any other material that has a bearing on the quotation offer, the suppliers commercial position (including joint venture agreements), preferencing arrangements, or samples of materials considered necessary by the CCT for the purpose of the evaluation of the quotation. If the Specifications require the supplier to provide samples/technical data sheets, these shall be provided strictly in accordance with the instructions set out in the Specification. If such samples /technical data sheets are not submitted as required in the bid documents or within any further time stipulated by the CCT in writing, then the bid concerned will be declared non-responsive. The Municipal Bidding Document 6.1 is attached, to be eligible for preference points bidders are required to submit a duly completed, current dated MBD 6.1 document with supporting documents with every RFQ submission, failure to submit will result in zero-point allocation. Please note that the MBD6.1 document is valid a year from date of signature. Tender Link : https://web1.capetown.gov.za/web1/procurementportal/RFQ/Details/316924
