Bids Are Invited For Acquisition Of Kitchen Utensils And Sets Of Tables And Chairs For Children And Adults For The Cafeterias Of School Units In The Municipal Education Network Of Lagoa Do Barro Do Piauí

Lot 1 - Tray With 6 Stainless Steel Divisions For Meals, Stackable For Easy Cleaning, Dimensions 400Mmx0.66Mm, Lot 1 - Deep Stainless Steel Plate For Meals, Easy To Clean, Diameter 22 Cm, Lot 1 - Stainless Steel Cup With Handle, 200 Ml Capacity, Lot 1 - Stainless Steel Meal Soup Spoon, Lot 1 - Stainless Steel Meal Fork, 01/08/2026 - 09:04:50, Lot 1 - Stainless Steel Meal Knife With Rounded Tip, Lot 1 - Stackable, Easy-To-Clean Plastic Tray, Dimensions48 Cm Top: Must Be Injected Into Abs Thermoplastic And Have A 0.8M High-Pressure Melamine Laminate Upper Surface, In Gray Color, Glued With Bi-Component Adhesive. On One Of Its Sides, It Must Have Two Couplings That Perform The “Connect” Function, Fitted To The Lateral Ends Of The Tables With The Aim Of Connecting One Table To Another When Placed Side By Side, Together With A Total Of 4 Tables. It Must Present Approximate Measurements Of 3204Mm X 801Mm X 590Mm. Chairs: The Set Must Have 8 Chairs. It Must Be Made Of Engineering Thermoplastic (Polypropylene Copolymer) Added With Fiberglass, Without Toxic Elements. It Must Follow The Monoblock Construction Concept, Where All The Parts That Must Make Up The Product, Such As The Back, Seat And Feet, Must Be Produced Through A Single Injection Cycle, Making It Robust And At The Same Time Light And Easy To Handle. Must Be Stackable Into A Minimum Of Eight Units. The Feet Must Have A “V” Shape Construction, Which Originate Close To The Central Region Of The Seat. The Lower End Of The Feet Must Receive A Shoe, Which Must Be Manufactured In Rsn Hytrel, In Order To Avoid Direct Contact Between The Feet And The Supporting Surface. It Must Have The Following Approximate Dimensions: Backrest: 333 Mm Wide And 242 Mm High; Seat: 415Mm Wide X 272Mm Deep. Seat Height To Floor: 363Mm., Lot 2 - Dining Room Set 08 Adult Seats Table With Single Top, Seamless, Measuring 2150Mm In Length And 950Mm In Width, With A Thickness Of 8Mm And A Seamed Edge Measuring 50Mm Made From Virgin Abs High-Impact Thermoplastic Resin, Free From Mineral Fillers, Manufacturers Logo Injected Into The Surface Of The Top. Top Fixed To The Structure Using Screws. Height From Top To Floor Is 760Mm. Table Top Base Formed By Two Square Tubes Measuring 25X25mm Positioned Under The Table Top, Manufactured Using The Mechanical Forming Process By Folding, Covering The Entire Perimeter Of The Table, Resulting In Two Welding Points And A Horizontal Support Bar Made From 25X25mm Tube, 4 Columns With 2 Inch Tube For The Feet, With Resin Tips Injected Pp Plastic (Polypropylene). The Entire Metal Structure Is Manufactured From Carbon Steel Tubes Treated By Sets Of Chemical Baths For Protection And Longevity Of The Structure And Welded Using The Mig System. Chair With Seat And Back In Pp Resin (Polypropylene). Vertical And The Seat Is Approximately 400Mm Wide By 460Mm Deep, Both Components Mounted On A Tubular Carbon Steel Structure, Produced In Tubes That Form The Base Of The Seat, Back And Legs. Connection Bar Made Of 7/8” Tube. Reinforced Seat In Round Tube With Diameter Of 22.22Mm. All Metal Structure Electrostatically Painted Nacor C