Request For Quotation Raw Materials And Materials For The Zhangalinsky Group Water Supply System

The Cast Iron Flanged Ball Check Valve Hq41x-16 (Ru-16) With Dn80 Is Used To Prevent The Reverse Flow Of The Medium, Is Reliable In Hot And Cold Water Supply, Sewerage And Water Treatment Systems, Withstands Pressure Up To 16 Bar And Temperature Up To 80°C. Main Characteristics: Body Material - Cast Iron, Valve Type - Ball Check Flanged, Nominal Diameter (Dn) - 80 Mm, Maximum Working Pressure (Pn) - 16 Bar, Length - 300 Mm, Maximum Medium Temperature - Up To 80°C, Weight - About 14.8 Kg (Approximately For Dn80 According To Different Manufacturers), Connection - Flange (Raw Materials And Materials Lhv), Drl Lamp 250 W, High-Pressure Mercury Phosphor Arc Lamp With High Luminous Efficiency, Designed For Lighting Large Areas And Industrial Premises, Operating From A 220 V Network With The Need For A Ballast (Choke). Main Characteristics: Lamp Type – Mercury Arc Phosphor (Maf), Power – 250 W, Base – Standard E40, Mains Voltage – 220 V (50 Hz), Luminous Flux – About 13,500 Lumens, Luminous Efficiency – From 32 To 58 Lm/W, Glow Color – White, Lamp Length – About 228 Mm, Bulb Diameter – About 91 Mm, Average Resource Is About 10,000–12,000 Hours Of Operation. (Raw Materials And Laiv Materials), An Electric Welded Coupling With A Diameter Of 32 Mm Made Of Polyethylene Grade Pe100 With Sdr11 Is Designed For Reliable Connection Of Pipelines For Water And Gas At Pressures Up To 16 Atm For Water And 10 Atm For Gas, Having High Strength And Resistance To Corrosion, With Installation Using Electrofusion Welding. (Raw Materials And Laiv Materials), Hatch Type L 3 Ton. Polymer-Composite Manholes Are Lightweight, Durable And Weather-Resistant Coatings Designed To Protect Inspection Shafts Of Utility Networks And Provide Convenient Access To Communications. Material Of Manufacture: Polymer-Composite Mixture, Often With The Addition Of Sand And Heat-Resistant Dyes, Which Ensures High Strength And Durability. The Material Does Not Corrode And Is Resistant To Ultraviolet Radiation And Moisture. Strength And Load: Depending On The Type, The Hatch Must Withstand Loads From 1.5 To 25 Tons Or More, Which Allows Them To Be Installed Both In Pedestrian Areas And On Roads With Passenger Vehicles. Weight: Composite Hatches Are Much Lighter Than Cast Iron, The Weight Of The Body With A Cover Usually Varies From 10 To 80 Kg Depending On The Model, Which Simplifies Installation And Reduces The Load On The Structure. (Raw Materials And Laiv Materials), An Electric Welded Coupling With A Diameter Of 25 Mm Made Of Polyethylene Grade Pe100 With Sdr11 Is Designed For Reliable Connection Of Pipelines For Water And Gas At Pressures Of Up To 16 Atm For Water And 10 Atm For Gas, Having High Strength And Resistance To Corrosion, With Installation Using Electrofusion Welding. (Raw Materials And Laiv Materials), The Stvkh-80 Water Meter Is A Turbine Cold Water Meter With A Diameter Of 80 Mm, Designed For Industrial And Municipal Needs With A Maximum Flow Rate Of Up To 200 M³/H, Characterized By High Accuracy, Durability And Ease Of Installation. Main Technical Characteristics Of Stkh-80: Nominal Diameter - 80 Mm, Maximum Water Flow - Up To 200 M³/H, Sensitivity Threshold - 0.40 M³/H, Installation Length - 225 Mm, Operating Pressure - 1.6 Mpa (16 Kgf/Cm²), Water Temperature Range - From +5 To +50 ° C, Protection Degree - Ip54 (Options With Ip68 Are Found In Analogues), Error – ±5% At Minimum Flow, ±2% At Transition And Higher. (Raw Materials And Laiv Materials), Contactor Kmi-23260 32 A In A Protective Sheath Is Designed For Remote Switching On And Off Of Three-Phase Asynchronous Electric Motors With A Squirrel-Cage Rotor And Protects Them From Overloads And Short-Circuit Currents At Voltages Up To 400 V. Main Characteristics And Purpose: Rated Current - 32 A, Rated Control Voltage - Up To 380 V Ac (Ac-3), Degree Of Protection Of The Shell - Ip54, Which Provides Protection From Dust And Splashing Water, Allowing The Contactor To Be Used In Construction Sites And Production Workshops With High Dust Levels And Humidity. The Contactor Is Equipped With A Thermal Relay Rti And A Shell With Seals And Control Buttons, Which Protects Electric Motors From Overloads And Phase Imbalance (Breakage Of One Of The Phases) During Operation. (Raw Materials And Laiv Materials)