Request For Quotation Purchase Of Equipment, Parts And Optical Instruments For Drones

Cr-Pla Carbon -Filament Reel 1. 5Pcs. 2. Pla Material (Polylactide) With The Addition Of Carbon Fiber (Carbon‑Fibre). 3. Filament Diameter 1.75Mm (±0.03‑0.05Mm). 4. Reel Weight 1 Kg. 5. Recommended Nozzle Temperature ≈190-230°C 6. Table Heating Temperature ≈25 To 60°C., Soldering Kit -Solder 1. 3Kg. 2. Tin Content Of At Least 60% And Flux Content Of At Least 2%. -Rosin 1. 0.2 Kg 2. The Main Component Of The Composition Should Be Natural Resin. Flux 1. 1L. 2. For High-Temperature Soldering With A Composition Such As Ethyl Alcohol 90-95% Pine Rosin Grade “A” 20-25% Diethylamide Hydrochloride 3-5% Triethanolamine 1-2%. Connector Xt 60 1.150 Set. 2. Set Of 2 Connectors Type Xt 60 (Female-Male), For Connecting Power Contacts., Glue Sticks - Glue Stick 7 Mm 1. 100Pcs. 2. Material - Eva (Eva) Or Polyolefin Hot Melt Glue. 3. Approximate Operating Melting Temperature Is Not Less Than 150°C. 3. Diameter 7Mm. - Glue Stick 11 Mm 1. 100 Pcs. 2. Material - Eva (Eva) Or Polyolefin Hot Melt Glue. 3. Approximate Operating Melting Temperature Is Not Less Than 150°C. 3. Diameter 11Mm., Repair Fabric And Resin Kit -Polyester Resin. 1. 10Pcs. 2. Hardening Time At +20°C Is No More Than 45 Minutes. 3. Resin Density 1.1G/Cm³. -Hardener. 1. 10Pcs. - Glass Mat (Reinforcing Fabric / Fiberglass) 1. 10 Pcs. -Measuring Containers. 1. 10Kt. -Brushes 1. 10 Sets. -Gloves 1. 10 Sets., Cr-Petg Plastic -Reels With Filament (4*1Kg) 1. 5Kt. 2. Petg - Polyethylene Terephthalate Glycol-Modified, Which Translates As “Polyethylene Terephthalate With Glycol Modification.” 3. Filament Diameter 1.75Mm (±0.03‑0.05Mm). 4. Reel Weight 1 Kg. 5. Recommended Nozzle Temperature ≈230-250°C 6. Table Heating Temperature ≈70-90°C., Nickel Tape Set 1. 10M 2. Nickel (Ni) Or High Purity Nickel Alloy (Usually ≥99.5%). 3. Width No Less Than 8 Mm 4. Thickness No Less Than 0.2 Mm 5. Length No Less Than 10 M. Connector Xt 60 1,150 Set. 2. Set Of 2 Connectors Type Xt 60 (Female-Male), For Connecting Power Contacts., Cr-Abs Plastic -Reel With Filament 1. 10Pcs. 2. Abs (Acrylonitrile Butadiene Styrene) Is Acrylonitrile Butadiene Styrene, A Thermoplastic Polymer. 3. Filament Diameter 1.75Mm (±0.03‑0.05Mm). 4. Reel Weight 1 Kg. 5. Recommended Nozzle Temperature ≈220-260°C 6. Table Heating Temperature ≈ 90-110°C., Thermal Insulation Set -Therm Shrink Tubes 1. 5300 Pcs. 2. Diameter Before Shrinkage 10Mm. 3. Shrinkage Ratio Of At Least 2:1. 4. Operating Temperature ≈ 55°C To +125°C. 5. The Temperature At Which Shrinkage Begins Is At Least 80°C., Wire Set For Installation - Wire Awg 30 1. 250M. 2. A Set Of At Least 5 Colored Silicone Wires (Two Colors Must Be Black And Red). - Wire Awg 28 1. 250M. 2. A Set Of At Least 5 Colored Silicone Wires (Two Colors Must Be Black And Red). - Wire Awg 16 1. 100M 2. Set Of 2 Silicone Wires, Black And Red. - Wire Awg 14 1. 50M 2. Set Of 2 Silicone Wires Black And Red.