Lot 1 - Safety Pants For Electricians, Risk Category Ii, Size 44, As Per Attached Specification. Successful Bidder Must Submit Reports And Tests Of The Materials Used In Making The Piece, Indicate Brand And C.A., Lot 2 - Safety Shirt For Electrician, Risk Ii, Dmlu, Size G, Cfe. Esp. Attached. Successful Bidder Must Indicate Brand And C.A., Size Lg, Lot 3 - Safety Jacket For Electrician, Lot 4 - Glove Made Of Natural Rubber, Flame Retardant, Red Stripe, For Maximum Voltage Of 1000V. They Can Be All Black. The Gloves May Have The Edge Of The Wrist Rolled Up For Reinforcement, By Means Of Thickening The Material Itself, Without The Presence Of Sharp Corners. They Must Be Free From Harmful Irregularities, Which Can Be Detected Through Visual Inspection, Manufactured With A Uniform Finish. Gloves Must Fully Cover The Users Hands, Wrist And Part Of The Forearm, Allowing Interdependence Of Movement Between The Fingers. Manufactured In Accordance With Specific Standards Astm D120/Nbr 10622/89 And Nbr 10624/89. Manufacturing Date A Maximum 6 Months Prior To The Effective Delivery Date. With Inmetro Marking Seal. All Gloves Must Be Marked, Indelibly On The Back Of The Wrist, Within A Range Of 50 Mm From The Edge, Permanently And Applied In Such A Way As Not To Harm The Properties Of The Glove. Identification By Means Of Stamps Will Not Be Accepted, The Pad Printing Process May Be Used. The Marking Must Contain, At A Minimum, The Following Information: A) Brand Or Name Of The Manufacturer; B) Type; C) Class; D) Size; E) Working Voltage (*) F) Serial Number; G) Manufacturing Date (Month And Year) (**) (Use Of Code Is Prohibited); H) Approval Certificate Number - Ac (Which Must Be Duly Approved By The Ministry Of Labor). Size 8., For Maximum Voltage Of 1000V. . They Can Be All Black. The Gloves May Have The Cuff Edge Rolled Up For Reinforcement, As Follows: A) Brand Or Name Of The Manufacturer; B) Type; C) Class; D) Size; E) Working Voltage (*) F) Serial Number; G) Manufacturing Date (Month And Year) (**) (Use Of Code Is Prohibited); H) C.A. Approval Certificate Number (Which Must Be Duly Approved By The Ministry Of Labor). Size 9., Lot 5 - Vaqueta Glove, Size 8, Used Over Class 00 Rubber Insulating Gloves. Made On The Palmar And Back Sides In Chrome Cowhide; Thickness From 0.60Mm To 0.70Mm; Union Of The Palmar Surface With The Dorsal Surface In An Overlapping Upper Seam; Cowhide Reinforcement Strip Between The Thumb And Index Fingers; Adjustable Cowhide Strap With A Width Of 15 Mm On The Back With Velcro; Vaqueta Artery Protector; Chrome Scratch Handle, Thickness 1.0 To 1.2 Mm; Joining The Wrist To The Palm And Back In Double Stitching; Thread In Polyester Or Cotton Thread; Length + 250 Mm. This Glove Must Comply With The Requirements Of Nbr 13712/1996. . Successful Bidder Must Indicate Brand, Size 9.2 Mm; Joining The Wrist To The Palm And Back In Double Stitching; Thread In Polyester Or Cotton Thread; Length + 250 Mm. This Glove Must Comply With The Requirements Of Nbr 13712/1996. Successful Bidder Must Indicate Brand., Lot 6 - Paratrooper Type Safety Belt, Made Of High Density Polyamide, With At Least Four D-Shaped Rings Made Of Steel, Two Located On The Waist Strap, One On The Front Strap At Chest Height And One On The Back. With Points
We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.
