Tenders Are Invited For Construction Of Street Lighting In Holendry Baranowskie. Project Co-Financed As Part Of The Bridge Program Of The Development Strategy For The Cpk Surrounding Area 2025.

Construction Of Street Lighting In Holendry Baranowskie. The Project Is Co-Financed As Part Of The Bridge Program Of The Development Strategy For The Cpk 2025 Surrounding Area, Including: The Subject Of This Study Is The Construction Of A Section Of The Overhead Low-Voltage Line For Road Lighting, Type Asxsn 2X25 Mm2, Along With The Development Of 59 Pole Positions. The Investment Is Located In The Town Of Holendry Baranowskie, Plot No. 467, 468, 470, 471, 472, 473, 474, 1250/1, 1250/2, 497, 496, 495, 493, 498, 499, 501, 985, 1015, 1016, 1020/1, 1022, 1023/1, 1023/2, 1025/1, 1025/2, 1026, 1057, 1058/1, 1058/2, 1059/1, 1059/2, 616/1, 1233/2, 1233/3, 1233/6, 1233/5, 634, 691/1, 691/3, 690, 910, 1139, 1140/1, 1140/2, 1141, 1142/1, 1143/3, 736, 737, 738/1, 738/2, 739 Baranów Commune. Currently, The Area Of Road No. 910 In Holendry Baranowskie Is Not Lit. At The Investors Request, The Expansion Of The Low-Voltage Lighting Network Is Planned, Along With The Installation Of Lighting Fixtures. A New Section Of The Low-Voltage Overhead Line For Road Lighting Is Planned, With A Cross-Section Of At Least 2X25mm2 And A Total Length Of 2,375M. The Long-Term Load Capacity For The Asxsn 2X25mm2 Cable Is Idd=112A. Good Quality Poles Should Be Used, Without Cracks Or Defects In Concrete That Would Weaken The Reinforcement, And The End Buried In The Ground Should Be Protected With Asphalt Varnish. Use Supports For Poles In Accordance With Pn-91/B-03020 For Medium Category Soil - Lowland Climate Zone. Slab Foundations Made Of U-85 Type Footing Slabs Are Planned For The Foundation Of Columns With E-Type Poles. The Columns Should Be Placed In Drilled Holes Diameter 0.80. To Protect The Lighting Line Against Atmospheric Discharges On The End Pole, Use Lightning Arresters 0.66/10 Ka And Ground Them With A Resistance Not Exceeding 10 Ω. It Is Planned To Use Fecu Rods 16-20 Mm, At Least 8 M Long, Driven Into The Ground And Metallic With A Fezn 4X25 Mm Flat Bar, Connected Together By Welding (Weld Length Not Less Than Twice The Width Of The Flat Bar). Protect The Joints Against Corrosion By Covering The Ground With Asphalt Varnish And The Above-Ground Part With Acid-Free Vaseline. In The Earthing Installation, Use Test Clamps Allowing For Earthing Measurements. In Order To Implement The Designed Construction Project, It Is Necessary To:• Build 21 Pole Stands On E-Type Poles (Circuit 01 - St.2-0286).• Build On The Planned Section Of The Road Lighting Overhead Line, I.E. From The Existing Pole No. 1 (Type Rpk-10/Zn) To The Designed Pole No. S-21. Pole Stands And Suspend The Asxsn 2X25 Mm2 Lighting Cable.• Build 21 Pole Stands On Type E Poles (Circuit 01 - St.2-0129).• Build 17 Pole Stands On Type E Poles (Circuit 01 - St.2-0129).• Existing Measurement System With Control Located At Lv Station No. 1 2-0286 Adapt According To Drawing E-07.• Install On The Pole Of The Pge Dystrybucja S.A. Pole Stand A New So Connector For Road Lighting Control And Measurement Made Of Thermoset