Quotation Are Invited For Servicing Of Clean Water Recovery & Wash Water Recovery Pump Including Testing Of The Pump

Quotation are invited for L-Station Desal-Servicing of Clean Water Recovery & Wash Water Recovery Pump. Total Nos:2, including Testing of the Pump. L-STATION DESAL REQUIRED OVERHAULING OF CLEAN WATER RECOVERY PUMP & WASHWATER RECOVERY PUMP.QTY # 2 EA1 UNCOUPLE THE MOTOR FROM THE PUMP BY REMOVING THE COUPLING BOLTS. TAKEAND RECORD THE INITIAL ALIGNMENT READINGS2 BEFORE ANY FURTHER DISASSEMBLY / DISCONNECTION, MARK AND RECORD ALLPOSITIONS OF JOINTS, LEADSAND TERMINALS OF MOTOR AND PUMP PARTS TO FACILITATE REASSEMBLY.3 REMOVE THE COUPLING S PACER4 DISCONNECT ALL AUXILIARY PIPING FOR COOLING, VENTING, SEALING ETC5 REMOVE THE PUMP AND SHIFT TO CONTRACTOR WORKSHOP6 DISMANTL E THE PUMP ACCORDING TO PUMP MANUFACTURER#S PROCEDURES7 CHECK AND RECORD INITIAL RUNNING CLEARANCES BETWEEN IMPELLER ANDCASING WEAR RINGS8 DISMANTLE THE PUMP ACCORDING TO PUMP MANUFACTURER#S PROCEDURES CONFIRMREFERENCE MARKS ACROSS EACH JOINT TO FACILITATE REASSEM BLY. ALL PARTSSHALL BE CLEANED THOROUGHLY AND PRESERVED AND PROTECTED AGAINST DUST ANDACCIDENTS. WHEREVER REQUIRED, TEMPORARY RUST P REVENTION COATING SHALL BEAPPLIED. CLEAN ALL PUMP PARTS AND ABRASIVE BLAST AS REQUIRED9 AFTER COMPLETE DISASSEMBLY INSPECT PUMP SHAF T AND SLEEVES VISUALLY FORANY MECHANICAL DAMAGE. MEASURE THECLEARANCES BETWEEN SHAFTS AND SLEEVES AND BETWEEN IMPELLER AND CASINGWEA R RINGS.10 CHECK AND RECORD THE RUN OUT OF SHAFT (STRAIGHTEN ALL DEFLECTIONS).11 INSPECT IMPELLERS FOR CORROSION, EROSION OR WEAR AN D REPAIR ORREPLACE. CHECK KEY WAYS BY DPI OR MPI AS APPLICABLE, INSPECT IMPELLERSWEAR RINGS AND CASING RINGS AND REPAIR OR REPLACE A S DIRECTED BY DEWA.12 INSPECT PUMP CASING, AND ALL OTHER PARTS OF THE PUMP FOR CORROSION,WEAR, EROSION, CRACKS, COATING DAMAGE ETC.. . REPLACE OR REPAIR ASDIRECTED BY DEWA AND APPLY NEW COATING WHEREVER THE ORIGINAL ONEDAMAGED.13 CLEAN AND INSPECT ALL BOLTS, NUTS A ND FASTENERS FOR DISTORTION ANDDAMAGE TO THREADS AND HEADS. REPLACE AS NECESSARY. ANY SUBSTITUTIONS OFTYPE AND MATERIAL MUST BE APPR OVED BY DEWA BEFORE USE.14 REPLACE BEARINGS.15 INSPECT MECHANICAL SEALS AND REPLACE OR REPAIR THE WEARING PARTS IFFOUND NECESSARY16 CARRY OUT DPI FOR PARTS OF THE PUMP SUCH AS IMPELLERS, SHAFTS,COUPLING BOLTS AND ALL THE PARTS DEEMED NECESSARY. ANY EVIDENCE OFCRAC KING SHALL BE EITHER REPAIRED OR REPLACED. BALANCING OF IMPELLER TOBE DONE17 ON RECEIPT OF THE DEWA INSTRUCTION TO PROCEED WITH THE RE-ASSEMBLY,THE CONTRACTOR SHALL RE-ASSEMBLE THE PUMP USING NEW AND REPAIR COMPONENTAS DETAILED IN APPROVED REPORT.18 CLEAN, LUBRICA TE AND GREASE PUMP PARTS AS REQUIRED, PRIOR TOREASSEMBLY AND BALANCING OF IMPELLER TO BE DONE AS PER PUMP MANUFACTURERPROCEDURE AND SPECIFICATIONS.19 RE-ASSEMBLE IN ACCORDANCE WITH THE MANUFACTURERS# PROCEDURE ANDDRAWINGS, TAKING INTO CONSIDERATION ALL SPECIFIED C LEARANCES ANDTOLERANCES. AT EACH STAGE, FREE ROTATION OF COMPONENTS IS TO BE CHECKEDAND RECORDED. CHECK, ADJUST AND RECORD THE CLEAR ANCE BETWEEN SHAFTS ANDBEARINGS BETWEEN IMPELLERS AND CASING. THE PUMP SHALL ROTATE FREELYWITHOUT RUBBING AFTER FINAL ASSEMBLY.20 SH IFT THE PUMP FROM CONTRACTOR WORKSHOP TO DEWA SITE21 RE-INSTALL THE PUMP. Qty: 1 L-Station Desal-Servicing of Clean Water Recovery & Wash Water Recovery Pump. Total Nos:2, including Testing of the Pump. STANDARD TERMS & CONDITIONS 1) Prices should be DDP delivery duty paid at DEWA stores. 2) Quotation to be submitted only in local currency U.A.E Dirhams 3) DEWA Standard payment terms is 30 days credit from the date of acceptance of material 4) No DEWA staff or his or her relatives up to third degree should have ownership or partnership in your company, and your participation in DEWA tenders / RFQs should not constitute a Conflict or perceived Conflict of Interest. Supplier Registration: https://srm.dewa.gov.ae/irj/portal/anonymous/regis Tender Link : https://srm.dewa.gov.ae/sap/opu/odata/sap/ZSRM_RFX_REG_BID_SRV/AttachmentSet(2332502452)/$value