Brake Working Cylinder For The Gaz-53 Car Main Characteristics: Type: Hydraulic Wheel Cylinder, Double Piston Diameter Of The Piston: 32 Mm, Work Piston: Up To 12 Mm, Pressure In The System: Up To 5-7 Mpa Assignment: Under The Brake Pipe With A Thread M10 × 1, Body Material: Cast Iron In20 Material Of Cuffs: Oil -Zoom -Resistant Rubber (Nbr), Mass Of One Cylinder: ≈ 0.8 Kg The Composition Of The Kit (On One Wheel): The Brake Cylinder Assembly - 1 Pc., Pistons - 2 Pcs. Rubber Cuffs - 2 Pcs. Refusse Spring - 1 Pc., Protective Anthers - 2 Pcs. Gost 32516-2013., Vacuum Brake (Vut) For The Brake System Of The Gaz 53. The Main Characteristics: Type: Diaphragm Vacuum Amplifier, Diameter Diaphragm: 250 Mm, Amplification Factor: 3.5–4.0, Working Release: Up To –0.08 Mpa, Output: Up To 2500 N, Connection: To The Collection Of The Ø Ø12 Mm Vacuum Hose To The Main Brake Cylinder (M10 × 1), Case: Steel With Anti -Corrosion Coating. Mass: ≈ 4.5 Kg. The Composition Of The Node: The Amplifier Case - 1 Pc., Rubber Diaphragm - 1 Pc., Return Spring - 1 Pc., Vacuum Valve - 1 Pc., Pedal Pusher - 1 Pc., Vacuum Hose Fitting - 1 Pc. Gost 32516-2013., The Ignition Coil For The Gas-53, V8, 4.25 Liter Gasoline Engine. . Main Characteristics: Type: Transformer, Cylindrical, Model (Factory): B117a Or Analogue, Nominal Power Voltage: 12 V, Primary Winding: Resistance 3.1–3.3 Ohms, Secondary Winding: Resistance ≈ 7.5–9.0 Kom, Output Voltage: Up To 25,000 V, Polarity: The Negative Terminal Is Connected To The Interrupter (Trambler), Positive - With The Ignition Lock, Operating Temperature: –40 ...+100 ° C Mass: ≈ 1.1 Kg. The Composition Of The Kit: Ignition Coil - 1 Pc., Mounting Bracket - 1 Pc., Contact Conclusions (+, -, Bb). Gost 28827-90., Brake Drum Rear Left Car Gaz-53. The Main Characteristics: Type: Cast -Iron Cast Drum, The Diameter Of The Working Surface: ≈ 350 Mm, Width Of The Working Surface: ≈ 100 Mm, Wall Thickness (New): ≈ 12–14 Mm, Permissible Wear In Diameter: Up To +2 Mm From The Face Value, Number Of Fasteners: 8 Pcs., Planting The Rear Hub: ≈ 22–25 Kg. The Material Is High-Strength Gray Cast Iron Cca25 (Gost 1412-85), The Working Surface Is Thermal To Increase Wear Resistance. Gost 32516-2013., The Rear Hub Assembled The Left On The Rear Bridge Of The Gaz-53 Car, The Composition Of The Kit (On One Side): The Rear Wheel Hub-1 Pc., Conical Bearings: Internal (Large)-1 Pcs., Outdoor (Small)-1 Pc., The Seal Of The Hub-1 Pcs., Fulfic (Adjusting Sleeve)-6 Pcs., Hube Nut-6 Pcs. Stop Puck - 1 Pc. Main Characteristics: Hub Material: High -Strength Cast Iron/Steel 45L, The Number Of Studs: 8 Pcs. (Under The Wheel Drives Of The Gaz-53), The Diameter Of The Landing For Bearings: According To The Factory Standard (Approximately 80 Mm And 50 Mm), The Mass Of The Hub Assembly: ≈ 18–20 Kg, Lubrication Of Bearings: Consistent (Litol-24 Or Analogue). Bearings (Factory Numbers): External: 6–7311 (Or Analogue), Internal: 6–7312 (Or Analogue). Gost 32516-2013., The Piston Group For The Gas-53, V8 Gasoline Engine, A Working Volume Of 4.25 L (4254 Cm³), Size: Standard. Composition Of The Kit: 1. Piston - 8 Pcs. 2. Piston Finger - 8 Pcs. 3. Stop Rings - 16 Pcs. 4. Piston Rings (Set Of 8 Pistons): - Upper Compression - 8 Pcs. - The Lower Compression - 8 Pcs. - Oilflow - 8 Pcs. Main Characteristics: Cylinder Diameter: 92.0 Mm (Standard), Piston Stroke: 80 Mm, Engine Operating Volume: 4254 Cm³, Compression Degree: 7.0–7.6. Piston Material: Aluminum Alloy With Heat -Resistant Inserts. Material Of Rings: Alloy Cast Iron With Chrome/Molybdenum Spraying. Diameter Of The Piston Finger: 30 Mm The Weight Of The Kit ≈ 12-14 Kg. Operating Conditions: Operating Temperature: Up To +250 ° C (Piston Zone). The Resource Of The Kit: 100-150 Thousand Kilometers. Gost 31440.1-2011, A Set Of Copper Sealing Washers For Cylinder Sleeves For The Gaz-53, V8, 4.25 Liter Gasoline Engine. Main Characteristics: Material: Annealed Copper (M1, M2 According To Gost 495-92). Inner Diameter: ≈ 92.0 Mm (By Landing Of The Sleeve). External Diameter: ≈ 100–102 Mm. Thickness: 1.0–1.2 Mm (Grinding Is Allowed Before Installation) Firmness After Annealing: Hb 45–65. The Temperature Range Of Operation: Up To +300 ° C. Seal Pressure: Up To 7–9 Mpa. The Composition Of The Kit: Sealing Washer - 8 Pcs. (According To The Number Of Cylinders). Gost 19752 - 84, Muffler (Exhaust) For The Car Gaz 53. Main Characteristics: Type: Reactive-Aborrect (Combined), Case Material: Low-Carbon Steel, With Alumocyque Or Heat-Resistant Coating, Muffler Length: ≈ 900–950 Mm, Body Diameter: 180–200 Mm, Input: Ø 52 Mm, Output: Ø 48 Mm, Mass: 7-8 Kg. Design: Cylindrical Welded Housing, Inside - Perforated Pipes And Partitions, Sound -Absorbing Filler - Basalt Fiber Or Mineral Wool, Fastening To The Exhaust Pipe - Clamps And Brackets. Gost 32328-2006., Remcommuver Of Gaskets For The Gas-53, V8, 4.25 Liter Gasoline Engine. The Composition Of The Kit (Standard Set): - Gaskets Of The Cylinder Block (Hbc) - 2 Pcs. (Asbestos/Metallo -Airbrush) - Gaskets Of Inlet And Gradu Collectors - Kit - Laying The Valve Cover - 2 Pcs. - Laying Of The Oil Pallet - 1 Pc. - Laying Of The Fuel Pump - 1 Pc. - Water Pump Gaskets - 1 Pc. - Gaskets Of Thermostat - 1 Pc. - Oil Filter Laying - 1 Pc. - Gaskets Of The Trambler And Lids Of The Camshaft - Set - Gaskets Of Indigenous And Connecting Rod Bearings - A Set - Carburetor Gaskets - Kit - Copper And Cardboard Sealing Rings For Small Nodes And Fasteners - Kit Main Characteristics: Materials: - Paronyte, Technical Cardboard, Asbestos Sheets With Metal Inserts - Sealing Rings - Excitement Copper, Oil -Zoom -Resistant Rubber Working Temperature: Up To +300 ° C (For Gaskets Of The Gbc And Collector) Sealing Pressure: Up To 7–9 Mpa Service Life: Before The Overhaul Of The Engine (80–120 Thousand Km) Gost 33786-2016., Front Crankshaft For The Gasoline Engine Gaz-53, V8, 4.25 Liters. Main Characteristics: - Type: Radial Reinforced Cuffs (Oil Seal) - Material: Oil -Bonas -Resistant Rubber (Nitrile Rubber Nbr) With A Metal Frame - Structure: With A Dustproof Edge Dimensions: - Inner Diameter (Planting On The Crankshaft): 70 Mm - External Diameter (Landing In The Lid): 92 Mm - Width: 10 Mm - Working Temperature: –40 ...+120 ° C -Working: Motor Oil Sae 15W-40, 20W-50 - Pressure: Up To 0.3 Mpa Gost 8752-79., Brake Drum Rear Right Car Gaz-53. 1. The Main Characteristics: Type: Cast -Iron Cast Drum, The Diameter Of The Working Surface: ≈ 350 Mm, Width Of The Working Surface: ≈ 100 Mm, Wall Thickness (New): ≈ 12–14 Mm, Permissible Wear In Diameter: Up To +2 Mm From The Face Value, Number Of Fasteners: 8 Pcs., The Weight Of One Drum: ≈ 22–25 Kg. The Material Is High-Strength Gray Cast Iron Cca25 (Gost 1412-85), The Working Surface Is Thermal To Increase Wear Resistance. Gost 32516-2013., The Back Hub Assembled The Right On The Rear Bridge Of The Gaz-53 Car, The Composition Of The Kit (On One Side): The Rear Wheel Hub-1 Pc., Conical Bearings: Internal (Large)-1 Pcs., Outdoor (Small)-1 Pc., Stupitsa Seal-1 Pcs., Fulfic (Adjusting Sleeve)-6 Pcs., Hube Nut-6 Pcs. Stop Puck - 1 Pc. Main Characteristics: Hub Material: High -Strength Cast Iron/Steel 45L, Number Of Studs: 8 Pcs. (Under The Wheel Drives Of The Gaz-53), The Diameter Of The Landing For Bearings: According To The Factory Standard (Approximately 80 Mm And 50 Mm), The Mass Of The Hub Assembly: ≈ 18–20 Kg, Lubrication Of Bearings: Consistent (Litol-24 Or Analogue). Bearings (Factory Numbers): External: 6–7311 (Or Analogue), Internal: 6–7312 (Or Analogue). Gost 32516-2013., The Rear Flashlight (Combined) For The Gaz 53 Car. Main Characteristics: Type: Combined, Two -Section, Power Voltage: 12 V, Lamp Power: Stop-Signal/Dimensions-21/5 W (Lamp Type A12-21/5) Turn-21 W (A12-21) Number Backlight-5 Watts. Fastening: Bolted, Through The Bracket. Corps: Metal With An Anti -Corrosion Coating, Diffuser: Plastic (Red/Orange/White). Design: The Housing Is Sealed, Cartridges For Incandescent Lamps. Lantern Sections: Red-Stop-Signal And Dimensions, Orange-Turning Indicator, White-Number Backlight (For The Left Lamp). Operating Conditions: Working Voltage: 10.5–14 V, Temperature Range: –40 ...+60 ° C, Resistance To Vibration And Dust In Accordance With Gost 8769-75. Gost 6964-72., A Set Of Oil Sequenic Caps (Valves) For The Gas-53, V8, 4.25 Liter Gasoline Engine. The Main Characteristics: Captacular Type Design, Fluoride Material (Fpm/Viton) Or Oil-Benzo-Resistant Rubber (Nbr), Amplification Of The Spring Ring For Squeezing On The Valve Rod, Operating Temperature: –40 ...+200 ° C, Valve Rod Diameter 9 Mm, Landing: On The Guiding Valve Bushing, Resource 60–80 Thousand. Km. Composition Of The Kit: Oil -Based Caps - 16 Pcs. (By The Number Of Valves: 8 Inlets + 8 Graduation). Gost 8752-79.
