tender for mla-sdf- 2025-26-construction of toilet for sn college ala-general civil work - toilet block 2 2.8.1:earth work in excavation by mechanical means (hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.all kinds of soil 3 od235182/2025-2026:dry rubble masonry _ dry rubble without concrete levelling course masonry with good quality blasted rubble including packing to compactness to lines and levels cost and conveyance of all materials labour charges etc. complete as per direction of departmental officers at site 4 4.1.3:providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-iii)derived from natural sources : 4 graded stone aggregate 20 mm nominal sizederived from natural sources) 5 7.1.1:random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:cement mortar 1:6 (1 cement : 6 coarse sand) 6 50.6.2.1:solid block masonry using pre cast solid blocks (factory made) of size 30x20x15 cm or nearest available size confirming to is 2185 part i of 1979 for foundation and plinth with thickness 15cm in: cm 1:6 ( 1 cement :6 coarse sand) etc complete 7 50.6.1.6:solid block masonry using pre cast solid blocks (factory made) of size 30x20x20cm or nearest available size confirming to is 2185 part i of 1979 for super structure above floor two level upto floor five level thickness 20cm and above in : cm 1:6 ( 1 cement : 6 coarse sand sand) etc complete 8 od235193/2025-2026:filling with contractors own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site engineer-incharge(50.2.25.1 modified) 9 4.1.8:providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level:1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) 10 5.9.5:centering and shuttering including strutting, etc. and removal of form for:lintels, beams, plinth beams, girders bressumers and cantilevers 11 5.9.3:centering and shuttering including strutting, etc. and removal of form for:suspended floors, roofs, landings, balconies and access platform 12 5.3:reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15°landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (zone iii)derived from natural sources: 3 graded stone aggregate 20 mm nominal sizederived from natural sources). 13 5.22.6:steel reinforcement for r.c.c work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelthermo - mechanically treated bars of grade fe-500d or more 14 13.1.2:12 mm cement plaster of mix:1:6 (1 cement : 6 fine sand). 15 13.16.1:6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand) 16 13.9.1:cement plaster 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement.12 mm cement plaster 17 13.43.1:applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:water thinnable cement primer 18 13.60.1:wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:two or more coats on new work 19 13.61.1:painting with synthetic enamel paint of approved brand and manufacture to give an even shade:two or more coats on new work 20 2.tile work 21 11.38:providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of ist quality conforming to is : 15622, of approved make, in all colours, shades, except white, ivory, grey, fume red brown, laid on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand), including pointing the joints with white cement and matching pigments etc., complete. 22 11.20.1:chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand).light shade pigment using white cement 23 od155504/2025-2026:providing and laying 60 mm thick factory made cement concrete interlocking paver block of m - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of engineer-in-charge. 24 8.31:providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in- charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 25 3.plumbing 26 17.3.1:providing and fixing white vitreous china pedestal type water closet (european type) with seat and lid, 10 litre low level white vitreous china flushing cistern & c.p. flush bend with fittings & c.i. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :w.c. pan with isi marked white solid plastic seat and lid 27 17.1.1:providing and fixing water closet squatting pan (indian type w.c. pan) with 100 mm sand cast iron p or s trap, 10 litter low level white p.v.c.flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever require:white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests 28 17.7.3:providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:white vitreous china wash basin size 550x400 mm with a pair of 15 mm c.p. brass pillar taps 29 50.17.1.3:supplying and fixing cp towel rod 60cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site engineer-in-charge. 30 50.17.1.4:supplying and fixing cp health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge. 31 50.18.9.13.1:providing and fixing pvc pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step pvc solvent cement and testing of joints complete as per direction of engineer-in-charge 25 mm dia 12 kgf/ cm2- external work- exposed on wall 32 50.18.9.4.1:providing and fixing pvc pipes includings jointing of pipes with one step pvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.32 mm dia 10.kgf/cm2 33 50.18.8.2.2:providing and fixing pvc pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step pvc solvent cement and testing of joints complete as per direction of engineer-in-charge. concealed work, including cutting chases and making good the wall etc. 20 mm pipe 10 kgf/ cm2 34 50.18.8.7.2:providing and fixing pvc pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes with one step pvc solvent cement and testing of joints complete as per direction of engineer-in-charge. concealed work, including cutting chases and making good the wall etc 63 mm pipe 4 kgf/ cm2 35 50.18.9.7.2:providing and fixing pvc pipes includings jointing of pipes with one step pvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.63 mm dia 4 kgf/cm2 36 50.18.9.9.1:providing and fixing pvc pipes includings jointing of pipes with one step pvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.110 mm dia 6kgf/cm2 37 50.18.9.20.1:providing and fixing pvc moulded fittings/ accessories for rigid pvc pipes, including jointing with pvc solvent cement - 63 mm dia elbow 38 50.18.9.20.6:providing and fixing pvc moulded fittings/ accessories for rigid pvc pipes, including jointing with pvc solvent cement -63x63x63 mm dia door tee 39 50.18.9.20.7:providing and fixing pvc moulded fittings/ accessories for rigid pvc pipes, including jointing with pvc solvent cement - 63 mm dia vent cowl 40 50.18.9.21.10:providing and fixing pvc moulded fittings/ accessories for rigid pvc pipes, including jointing with pvc solvent cement -75x63 mm dia reducer 41 50.18.9.22.1:providing and fixing pvc moulded fittings/ accessories for rigid pvc pipes, including jointing with pvc solvent cement - 110 mm dia elbow 42 50.18.9.22.4:providing and fixing pvc moulded fittings/ accessories for rigid pvc pipes, including jointing with pvc solvent cement- 110 mm dia bend 43 50.18.9.22.7:providing and fixing pvc moulded fittings/ accessories for rigid pvc pipes, including jointing with pvc solvent cement - 110x110x75 mm dia door tee 44 51.19.st2:supplying and installing ready made pvc septic tank including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (provision for cc/rcc/sand/06mm aggregate for the preparation of bed shall be paid separately)
2. 15 to below 25 flush capacity 45 19.33:constructing soak pit 1.20x1.20 m filled with brickbats including s.w. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. 46 18.48:providing and placing on terrace (at all floor levels) polyethylene water storage tank :isi 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 47 18.51.1:providing and fixing c.p. brass long body bib cock of approved quality conforming to is standards and weighing not less than 690 gms.15 mm nominal bore 48 18.53.1:providing and fixing c.p. brass angle valve for basin mixer and geyser points of approved quality conforming to is: 893115 mm nominal bore 49 18.55.2:providing and fixing ptmt stop cock of approved quality and colour.20 mm nominal bore, 89 mm long, weighing not less than 88 gms 50 4.joinery 51 od143969/2025-2026:supplying and fixing pvc door, including all cost and labours etc 52 9.117.2:providing and fixing factory made upvc door frame made of upvc extruded sections having an overall dimension as below (tolerance ±1 mm), with wall thickness 2.0mm (±0.2 mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. the hinge side vertical of the frames reinforced by galvanized m.s. tube of size19 x 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of engineer-in-chargeextruded section profile size 42x50 mm 53 9.124.2:providing and fixing factory made 30 mm thick door shutter made of solid pvc foam profile.the styles & rails shall be of size 75 mm x 30 mm having wall thickness 5 mm.the styles, top & bottom rails shall have one side wall thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power.the styles and rails shall be reinforced with m.s. tubes of size 33 mm x 17 mm x 1 mm, painted with primer, all four corners of reinforcement to be welded or sealed. solid pvc extruded bidding (push fit type) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5 mm pvc sheet as panel.the styles and rails will be mitred cut and joint with the help of pvc solvent cement & self driven self tapping screws.single piece extruded solid pvc lock rails of sixe 100mm x 30 mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of pvc solvent cement & self driven self tapping screws of size 100 mm x 8 mm complete as per manufacturers specifications and direction of engineer -in-charge.decorative finish (both side wood grained finish) 54 50.10.2:steel work for purlin/single section with g i pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete 55 21.1.1.3:providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is : 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminnium snap beading for glazing /paneling, c.p. brass/ stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge.(glazing, paneling and dash fasteners to be paid for separately):for fixed portionpolyester powder coated aluminium ( minimum thickness of polyester powder coating 50 micron ) 56 21.1.2.3:for shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of epdm rubber/ neoprene gasket required (fittings shall be paid for separately)polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micorn) 57 21.3.1:providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer - in -charge. ( cost of aluminium snap beading shall be paid in basic item):with float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) 58 21.7.1:providing and fixing machine moulded aluminium covering of approved pattern & design, made out of machine cut aluminium sheet and machine holed for receiving dash fastener, over expansion joints on vertical surfaces/ ceiling floors, the fixing on plate in one row on one side of joint only shall be done with stainless steel dash fastners of 8 mm dia and 75 mm long bolt including providing aluminium - washers 2 mm thick 15 mm dia, at a staggered pitch of 200 mm centre to centre including drilling holes in the receiving surface and providing expandable plastic sleeves in holes etc.complete as per drawing and direction of engineer -in-charge.anodised aluminium sheet 2.5 mm thick (anodised transparent or dyed to required shade according to is: 1868, minimum anodic coating of grade ac 15) 59 13.71:lettering with black japan pint of approved brand and manufacture 60 od143970/2025-2026:name board