material supply for mgnrega works mgnrega material supply tender , mgnrega materials , stone aggregate single size 20 mm nominal size , coarse sand zone3 , stone aggregate single size 10 mm nominal size , fine sand zone 4 , stone for masonry work , portland cement (sp53) 50kg , twisted steel reformed bars tmt bars , mild steel round bars for reinforcements , wire nails , galvanised wire mesh of average width of aperture 1.4 and nominal dia of wire .63 mm , mild steel tubes hot finished welded type , gi traffored profile sheet .35 mm thick , white vitreous china 10 lit (fully flush) capacity controlled low level flushing cisten with all fittings , pvc pipe 25 mm outer dia 10kgf/cm2 , pvc pipe 110 mm outer dia 4kgf/cm2 , bitumen washer , gi limpet washer , galvanised steel bolts and nuts 6 mm dia and 25 mm long round head with slots , galvanised steel j or l hooks 8 mm dia , synthetic enamel paint in black or chocolate shade , red oxide zinc chromate primer , welding by electric plant , solid brick of size 30*20*15 cm , pvc pipe 63 mm outer dia 4 kgf/cm2 , precoated galvanised steel plain ridges , solid brick of size 30*20*20 cm , wall form panel 1250*500 mm , corner angle 45*45*5 mm (1.5 m long) , 100 mm channel shoulder 2.5 m long , double clip ( bridge clip ) , single clip , m s tube 40 mm dia , dehradun white lime , bright finished or black enameled mild steel butt hinges 125*65*2.12 , bright finished or black enameled mild steel screws 50 mm , epoxy paint , stone aggregate single size 6 mm nominal size , mild steel round bar 12 mm dia and below , flats upto 10 mm thickness , anjili wood scantals , float glass sheet of nominal thickness 4 mm (weight not less than 10 kg/sqm , structural steel such as tees,angles,channels and r s joists , bright finished or black enameled mild steel butt hinges 100*58*1.9 mm , bright finished or black enameled mild butt hinges 50*37*1.5 mm , bright finished or black enameled mild steel screws 40 mm , bright finished or black enameled mild steel screws 20 mm , anodised aluminium handles 125 mm with plate 175*32 mm , chromium plated brass screws 25 mm , anodised aluminium tower bolt (barrel type) 300*10 mm , chromium plated brass screws 30 mm , 35 mm thick factory made solid panel pvc door shutter of single piece extruded profile non decorative finished (matt finished) , powder coated m s butt hinges 100*58*1.9 mm , through and bond stone size 24*24*39 cm , aluminium t or l sections , chromium plated brass screws 20 mm , powder coating 50 microns on aluminium sections , neoprene/epdm rubber gasket , vitreous china orissa type wc pan size 580mm , flushing cisten p v c 10 ltr capacity (low level) white with fittings,accessories and flush pipe , 100 mm sci trap with vent heel , vitreous china flat back wash basin 550*400 mm , 15 mm c.p brass tap , cp brass waste 32 mm , ci bracket for wash basin and sinks , stainless steel kitchen sink without drain board 470*420 mm bowl depth 178 mm , semi rigid pvc waste pipe for sink and wash basin 32 mm dia with length not less than 700 mm i/c pvc waste fittings , brass bib cock 15 mm dia , polyethelene water storage tank with cover and suitable locking arrangement , second class kail woods in planks , second class kail woods in scantling , hollock ballies 125 mm diameter , multi surface paint , special primer (c.w) , pvc pipe 32 mm outer dia 6 kgf/cm2 , ptmt soap dish/holder 138*102*75 mm , vitrified floor tile 60*60 cm , high polymer modified quickset tile adhesive , eposy grout , brass stop cock 15 mm dia