material supply for mgnregs , quarry waste , stone aggregate(single size): 40 mm nominal size , stone aggregate(single size):20 mm nominal size , stone aggregate(single size): 10 mm nominal size , stone aggregate(single size): 06 mm nominal size , fine sand (zone iv) , coarse sand (zone iii) , gravel 5mm to 10mm , stone for masonry work , portland cement , m.s. tube 40 mm dia , mild steel tubes hot finished welded type , galvanised steel bolts & nuts 6 mm dia and 25 mm long round head with slots , galvanised steel j or l hooks 8 mm dia , g.i limpet washer , bitumen washer , mild steel round bar 12 mm dia and below , mild steel round bar above 12 mm dia , mild steel sheets with bolts and nuts to rest on pintels , iron pintels including weldded pin , mild steel sheets for tanks , mild steel hooks , mild steel plate , mild steel tubes electric resistant or induction butt welded , welding by electric plant , wire nails , bright finished or black enameled mild steel butt hinges 100x58x1.90 mm , bright finished or black enameled mild steel screws 40 mm , bright finished or black enameled mild steel screws 20 mm , powder coated m.s. butt hinges 100 mm x58 mm x 1.9 mm , flats up to 10 mm in thickness , galvanised wire mesh of average width of aperture 1.4 and nominal dia.of wire 0.63 mm , g.i trafford profile sheet 0.35mm thick , precoated aluminium traffored sheet 0.450 mm thick , structural steel such as tees,angles,channels and rs joists , stainless steel screws 50 mm , red oxide zinc chromate primer , precoated galvanised steel plain ridges , stainless steel (grade - 304) hollow section round/square tubes , stainless steel bolts /square bar and plates , g.i pipe 40mm dia , gi plain washer thick , twisted steel/deformed bars , hire charges of concrete mixer 0.25 to 0.40 cum with hopper , vibrator (needle type 40 mm) , hire charge of 10 hp engine and pump set - materials , wall form panel 1250x500 mm , corner angle 45x45x5 mm 1.50 m long , 100 mm channel shoulder 2.5 m long , double clip (bridge clip) , single clip , wall form panel 1250x450xmm , corner angle 45x45x5 mm 2.50 long , column clamp 450x1070 mm , prop 2 m (2-3.5m) , adjustable telescopic prop 3 m (2.02-3.75m) , beam clamp 300-380 mm (450-1070 mm) , adjustable span eso+si (2.35-3.40) , second class kail wood in planks , second class kail wood in scantling , hollock ballies 125 mm diameter , solid blocks of size 30x20x20cm , solid blocks of size 30x20x15cm , hollow blok of size 40x20x10cm , interlocking c.c. paver block (80 mm thick, m-30) , pvc vent cowl 63 mm dia , pvc vent cowl 110 mm dia , brass bib-cock-15 mm dia , pvc pipe 63 mm outer dia . 6kgf/cm2 , pvc pipe 110 mm outer dia 6kgf/cm2 , pvc pipe 25 mm outer dia . 12 kgf/cm2 , pvc pipe 32 mm outer dia. 10kgf/cm2 , pvc elbow 63 mm dia , pvc 45 degree elbow 63 mm dia , pvc door elbow 63 mm dia , pvc bend 63 mm dia , pvc tee 63x63x63 mm dia , pvc socket/coupling 63 mm dia , pvc elbow 110 mm dia , pvc 45 degree elbow 110 mm dia , pvc door elbow 110 mm dia , pvc bend 110 mm dia , pvc tee 110x110x110mm dia , pvc socket/coupling 110 mm dia , pvc pipe 40 mm outer dia. 10kgf/cm2 , pvc pipe 20 mm outer dia 10 kfg/cm2 , pvc pipe 63 mm outer dia . 4kgf/cm2 , pvc pipe 32 mm outer dia 6kgf/cm2 , pvc pipe 40 mm outer dia. 6kgf/cm2 , pvc pipe 75 mm outer dia 6kgf/cm2 , pvc pipe 110 mm outer dia. 4kgf/cm2 , pvc pipe 160 mm outer dia. 4kgf/cm2 , pvc elbow 75 mm dia , pvc 45 degree elbow 75 mm dia , pvc socket/coupling 75 mm dia , pvc reducer 63x50 mm dia , pvc vent cowl 75 mm dia , vitreous china orrisa type w.c. pan size 580 mm , brass stop-cock 15 mm dia , flushing cistern p.v.c. 10 lts capacity (low level) (white) (with fittings, accessories and flush pipe) , 100 mm s.c.i. trap with vent heel , black plastic seat (soild) with lid c.p.brass hinges and rubber buffers , vitreous china pedestal type water closet , stainless steel kitchen sink - without drain board 470x420 mm bowl depth 178 mm , c.i. bracket for wash basin and sinks , polyethylene water storage tank with cover and suitable locking arrangemnet , vitreous china flat back wash basin 550x400 mm , 15 mm c.p.brass tap , c.p. brass waste 32 mm , rectangular shape 453x357 mm mirror with plastic moulded frame , rawl plug 50 mm (designation 10 nos) , ptmt - towel rail (600 mm) , chromium plated brass screws 25 mm , white vitreous china 10 lit. (full flush) capacity controlled low level flushing cistern with all fittings , factory made door frame size 50x47 mm with wall thickness 5 mm made of single piece extruded profile , 35 mm thick factory made solid panel pvc door shutter of single piece extruded profile non decorative finished (matt finished) , float glass sheet of nominal thickness 4 mm (weight not less than 10 kg/sqm) , aluminium t or l sections , hard board 6 mm thick , powder coating 50 microns on aluminium sections , neoprene / epdm rubber gasket , second class teak wood in scantling , 200 mm aluminium aldrop , multi surface paint , special primer (c.w) , synthetic enamel paint in black or chocolate shade , acrylic exterior paint , premium acrylic emulsion of interior grade, having voc content less than 50 gm/litre , exterior primer , epoxy paint , deharadun white lime , vitrified floor tile 60x60 cm , ceramic glazed tiles ist quality 300 x 300 mm in all shades and designs of white, ivory, grey, fume red brown etc. , ceramic glazed tiles ist quality minimum thickness 5 mm in all colours shades and designs except burgundy, bottle green black , bamboo nails , aracanut post , royalty for good earth , common burnt clay f.p.s. (non modular) bricks class designation 7.5