repairs to drains, culvert, grill grating, ms railing and other petty repairs and repairs to plumbing services and misc sanitary works for pt/ ty bldgs at comd hq incl anc camp, ins jarawa incl mt, ndv, odv, kumarkheti incl inwtc and zephyr under ge haddo, sri vijaya puram; 1 excavation in trenches n. exc 1.5m wide and n. exc 1.5m in depth in hard/dense soil for foundation, etc or for shafts, wells, cesspits, manholes, pierholes, etc n. exc 10 sqm onplan and getting out complete all as specified and directed 2 returning filling in hard/dense soil including spreading levelling watering and well ramming in layers n. exc 25cm thick complete all as specified and directed 3 removing excavated material (any type of soil) to a distance n. exc 50m and depositing where directed at a level n. exc 1.5m above the starting point complete all as specified and directed 4 m&l cement concrete 1:4:8 type d2 (using 40mm graded stone aggregate) as in foundations or mass concrete complete all as specified and as directed 5 m&l for plain cement concrete 1:2:4 type b1 (using 20mm graded stone aggregate) as in surface channel or drain or benching in manhole including necessary formwork complete all as specified and directed 6 extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds, mitered/stoppedends etc complete all as specified and directed 7 demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed 8 m&l for nominal mix rcc 1:1.5:3 type a1 (using 20mm graded crushed stone aggregate) inslabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves, chajja/facia and the like complete all as specified and directed 9 m&l for nominal mix rcc 1:1.5:3 type a1 (using 20mm graded crushed stone aggregate) in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under-reamed piles and mass concrete complete all as specified and directed 10 m&l for nominal mix rcc 1:1.5:3 type a1 (using 20mm graded stone aggregate) in walls, retaining walls, basement walls, ballast walls and the like, any thickness; above top of footings, including attached pilaster and buttresses complete all as specified and directed 11 m&l formwork for rough finished flat surface to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (horizontal or sloping) complete all as specified and directed 12 m&l formwork for rough finished flat surface to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter complete all as specified and directed 13 m&l formwork for rough finished flat surface to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc, vertical or to batter complete all as specified and directed 14 m&l formwork rough finished surface of concrete to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n. exc 20 cm wide and sides of rcc/pcc bands in walls, horizontal or sloping and similar work n. exc 10 cm wide complete all as specified and directed 15 m&l for mild steel tmt bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed 16 m&l for mild steel tmt bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed 17 dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed 18 s&fframed work such as grills, gratings etc with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar works like cooler stand conforming to fe-290, gde -e-165 19 s&f mild steel roof trusses (framed), trrussed, purlins, crane gantries, rails and fastenings and heavy bracket framming (beam,tee, angle, channels or flat sections) including distance pieces, cleats etc conforming to fe 410-w (gde-e-250) quality-a 20 s&f plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to fe-410-w (gde-e-250) quality-a complete all as specified and directed 21 m&l forapplying two coat of synthetic enamel paint over a coat of red oxide primer includingpreparation of new steel surfaces of any description over 10cm width or girth not otherwise described complete all as specified and directed 22 dismantling plain or corrugated steel sheeting, any gauge, thickness including nainital or similar pattern in roof coverings complete all as specified and directed 23 s&f pre-painted galvalume aluminium zinc coating gi based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed 24 s&f pre-painted galvalume aluminium zinc coating gi based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, ridges, fixed with self tapping screws all as specified and directed 25 dismantling wood boarding, panels, beams or any description, fixed any position with nails 26 m&l for 18mm thick designed rubco hut rubber wood frame shutter for cupboard, whb counter cupboard, wall with finish to match all adjoining surfaces including sanding and applying mixture offiller and ncd thinner (sheenlac make), pasting chalk putty, applying sealer (sheenlac make) and wall nut colour stainer and finally applying waxpol (silicon make) complete all as specified and as directed 27 m&l for 30mm thick rubber wood superior quality, chemically pressure treated, egde glued, finger jointed, tongued, grooved as in door shutter and finished with two coats of melamine polish with asian sealer and wood filler over a coat of honey/natural colour wood filler putty for dust free surface etc including preparation and applying three types of sand papers and surface finish to a glossy/ mat finish to match with the adjoining surfacecomplete all as specified and as directed.make of rubber wood members : rubco/ india wood or equivalant 28 m&l for 18mm thick hdf boarding (fire and water proof) as in cup boards/shutters/racks/shelves exterior grade with one side white lamination and other side coloured prelaminated, size of the cabinet as per requirement of the site complete all as specified and as directed by engr-in-charge. make : bajaj/ axis/greenply/ archidply or equivalent.note : (i) cutting edges of cupboard shutter/ shelves to be finished with adhesive edge binding tape all as directed 29 m&l for preparation of new/old wooden surfaces and applying melamine polish through the process of sanding with wood sanding paper of size 60 & 80 and applying wood filler mixed with ncd thinner including applying wood putty on shabby/ nailing area and sanding with sand paper of size 120 and applying sealer and walnut colour stainer and sanding with sand paper of size 320 and melamine polishing with spray application and again sanding with 400 sand paper and finally applying silicon of make waxpol with soft fine cloth for better shining and finishing complete all as specified and directed 30 s&f stainless steel auto closing hinges of standard size complete all as specified and directed 31 s&f stainless steel 150mm cupboard handles complete all as specified and directed 32 s&f stainless steel 100mm long tower bolts complete all as specified and directed 33 s&f magnetic door catcher for cup board complete all as specified and directed 34 s&f telescopic ball bearing runners minimum length 400mm(ka 5632) full extension load capacity 45 kg complete all as specified 35 demolition of precast cement concrete block walling built in cm or cement lime mortar complete all as specified and as directed. 36 m&l precast cement concrete block masonry exc 10 cm width with solid block pcc 1:3:6 type c1 (using 20 mm graded stone aggregate) and settingin cement mortar 1:4 all as specified 37 taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed 38 m&l for 10mm thick plaster in cm 1:6 on fair face of concrete surface or brick walls finished even and smooth without using extra cement complete all as specified 39 m&l for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over a coat of average 1mm thick wall care putty to make the surface smooth complete all as specified and directed 40 m&l for applying two coats of oil bound distemper over a coat of average 1mm thick wall care putty to make the surface smooth after complete removal of existing treatment complete all as specified and directed 41 m&l for 15mm thick plaster in cm 1:4 on fair face of brick walls or concrete surface including mixing of liquid water proofing compound @ 200ml per 50 kg cement bag, finished the surface even and smooth without using extra cement complete all as specified. (note: water proofing compound shall be measured and paid separately) 42 m&l for preparing newly plastered wall surface and applying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm/litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm complete all as specified and directed 43 m&l for complete removal of existing treatment on plastered wall surface and applying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm/litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm complete all as specified and directed 44 m&l for 10mm thick plaster in cm 1:3 on concrete ceiling surfaces finished even and smooth without using extra cement complete all as specified 45 m&l for preparation of newly plastered ceiling surface and applying two coats of oil bound distemper of approved tint over a coat of average 1mm thick wall care putty complete all as specified and directed 46 m&l for applying two coats of oil bound distemper of approved tint over a coat of average 1mm thick wall care putty on ceiling after complete removal of existing treatment complete all as specified and directed 47 demolition of cement concrete (un-reinforced) in ground floors and pavings n.exc 15cm thick (above or below gl) complete all as specified and directed 48 m&l for 75mm thick pcc 1:3:6 type c1 (using 20mm graded stone aggregate) as in plinth protection/path laid in panels, finish the top surfaces even and smooth complete including filling the joints with mastic compound all as specified and directed 49 m&l for 100mm thick pcc 1:4:8 type d2 (using 40mm graded stone aggregate) as in path finish the top surfaces even and rough to receive top layer complete all as specified and directed 50 m&l for chequered cement concrete tiles of size 30cm x 30cm x 25mm thick with grey cement and pigments set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile as in floor over and including 20mm thick screed bed in cm 1:4 complete all as specified and directed 51 s&f for 60mm thick factory made chamfered edge cement concrete paver block of m-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc of required strength, thickness & size/ shape, made by table vibratory method using pu mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified 52 taking down chowkhats or frames area n. exc 1.50 sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed 53 taking down chowkatsexc 1.5 sqm but n. exc 4 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed 54 taking down shutter of any description n. exc 1 sqm each complete all as specified and directed 55 taking down shutter of any description exc 1 sqm but n. exc2 sqm each complete all as specified and directed 56 taking down shutter of any description n. exc 1 sqm each and refixing in the same opening including resecuring or easing of door shutters for easy closing/ opening, end tightening of butt hinges in position, adjustment of butt hinges in position, adjustment of existing aluminium mongry complete all as specified and directed 57 taking down shutter of any description exc 1 sqm but n. exc2 sqm each and refixing in the same opening including resecuring or easing of door shutters for easy closing/ opening, end tightening of butt hinges in position, adjustment of butt hinges in position, adjustment of existing aluminium mongrycomplete all as specified and directed 58 s&f solid pvc door frame of size 50mm x 47mm made out of 5mm both side prelam pvc sheet and edges will be painted to match with the prelam sheet reinforced with ms square tube in opening incl necessary fixing arrangements as per specification and drawing complete all as specified and directed 59 s&f factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of ms tubes for top and bottom rails.ms frame shall be covered with heat moulded prelam pvc c channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and both side prelam pvc sheetfor top rail, lock rail and bottom rail on either side as gap insert for top rails, bottom rail, panelling of both side prelam pvc sheet to be fitting in the ms frame welded/sealed to the stiles and rails with suitable pvc sheet beading and joined together with solvent cement in the frame at site as per specification and drawing 60 s&f for 2nd class hard wood (sal) plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed 61 m&l for pcc 1:3:6 type c1 (using 20mm graded aggregate stone aggregate) as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in item 04028, water troughs and the like including weathering, holdfast, slightly rounded or chamfered angles and throatingcomplete all as specified and as directed 62 s&f 30mm thick flush shutter solid core construction with block board core and ply wood face panels, commercial type both sides complete all as specified make : green/century ply 63 s&f 30mm thick plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkhats complete all as specified 64 s&f 30mm thick 2nd class hard wood factory made glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified 65 s&f 100mm size stainless steel butt hinges medium weight complete all as specified 66 s&f 150mm aluminium, anodised, barrel tower bolts of extruded section all as specified 67 s&f 150mm size extruded aluminium alloy handles, fabricated type, anodised all as specified 68 s&f 250mm mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate 69 s&f floor door stopper ofaluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 140mm overall length of cover plate 70 s&f door seal bottom of width not less than 30mm and length (ranges 500mm to 1200mm) suitable according to door shutter width to protect entry of insects efficiently complete all as specified and directed 71 m&l for applying two coats of synthetic enamel paint to new undecorated wooden surfaces over a coat of pink primer including preparation, over 10cm width or girth complete all as specified 72 m&l for anodised aluminium frame for doors, windows, ventilators, partition, wind tie with one or more rebates including joining cleat for fixing etc complete as specified 73 m&l for anodised aluminium door shutters, aluminium section weighing not less than 1.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 nos in each door, hinges, tower bolts, anodised aluminium snap beading screws etc complete all as specifiednote : supply only floor spring, glass, ss friction hinges,particle board, wire gauze will be measured seperately 74 m&l for anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified complete all as specifiednote : supply only glass, particle board, wire gauze will be measured seperately 75 m&l for anodised aluminium window and ventilator shutters, side hung/sliding type without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays/imax hinges 01 no, hinges type b-21 100mm long 02 nos suitable handle 01 no per shutter or as required etc complete all as specified note : supply only glass, particle board, wire gauze will be measured and paid seperately 76 s&f anodised aluminium grill (anodised transparent or dyed to required shade according to is : 1868 with minimum anodic coating of grade ac 15) of approved design/ pattern, with approved standard section and fixed to the existing window frame with cp brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete all as specified and directed 77 hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone or steel/ aluminium frame concrete or brick surrounds, glazed complete all as specified 78 supply only figured glass, pin head type sheet glass 4 mm thick ordinary quality and glazing with aluminium glazing clip in aluminium window/ventilator shutter not exc 0.5 sqm in each pane 79 supply only sheet glass 4 mm thick ordinary quality and glazing with aluminium glazing clip in aluminium window/ventilator shutter not exc 0.5 sqm in each pane 80 supply only sheet glass 4 mm thick ordinary quality and glazing with aluminium glazing clip in aluminium window/ventilator shutter exc 0.5 sqm in each pane 81 supply only sheet glass 5.5mm thick ordinary quality and glazing with aluminium glazing clip in aluminium door/window/ventilator shutter not exc 0.5 sqm in each pane 82 supply only 12mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination, fixed with screws to timber frame work complete all as specified 83 supply only aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.4mm and fixed with aluminium wire staples all as specified and directed 84 m&l for aluminium composite panel sheet of 3mm thick with skin thickness of 0.25mm of aluminium on both sides, sandwiched by 2.5mm polyethylene core with pvdf coating of 30.0 micron fixed over framemade up of aluminium hollow section of 25x50mm, 2.0mm thick, duly fixed to wall/ceiling with expansion fastener having panels not exc 1200x1200mm with necessary silicon filling, in approved pattern as in columns, beams, walls etc complete all as specified and as directed.note : necessary scaffolding required for the work upto three storeyed bldg shall be deemed to include in the unit rate quoted 85 taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories complete all as specified and directed 86 s&f pvc (swr) pipe 110mm bore, single socketed, in any length including bends, socket etc with rubber ring joints and jointed with approved adhesive and fixed to wall complete all as specified and directed 87 s&f pvc (swr) pipe 110mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive laid in trenches or in floors complete all as specified and directed 88 s&f in repair pvc (swr) 110mm dia bend of any radius and jointed with approved adhesive complete all as specified and directed 89 s&f pvc (swr) pipe 75mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive fixed to walls complete all as specified and directed 90 s&f pvc (swr) pipe 75mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive laid in trenches or in floors complete all as specified and directed 91 s&f in repair pvc (swr) bend 75mm dia with access door, any radius as required and jointed with approved adhesive complete all as specified and directed 92 s&f in repair75mm outlet dia pvc (swr) floor trap with grating including jointing with solvent cement to waste pipe complete all as directed 93 taking up or down 15mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed 94 s&f 20mm outer dia cpvc pipes sdr 13.5 and plain cpvc sdr 11 fittings on walls/ceiling or laying in floors including suitable reducer for 15mm dia taps fitting as required complete all as specified 95 cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10 cm girth 96 taking up or down 20mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed 97 s&f of 25mm outer dia cpvc pipes sdr 13.5 and plain cpvc sdr 11 fittings on walls/ceiling or laying in floors complete all as specified 98 s&f in repair aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.4mm and fixed with aluminium wire staples all as specified and directed 99 s&f in repair stainless steel imax hinges for aluminium window shutters complete all as specified and directed 100 s&f in repair 600x450x6mm thick looking mirror bevelled edge of selected quality glass fixed with stainless steel glass fastner complete all as specified 101 s&f in repair curtain rods 25mm dia, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified 102 s&f in repair door closer hydraulically regulated aluminium (die cast) body, designation no 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified 103 s&f in repair double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed 104 s&f in repair vitreous china wash down water closed pan (pedestal pattern) white, including connection to drain (or out going pipe) and to flush pipe, antisypthonic (excluding flushing cistern and flush pipe) complete all as specified 105 s&f in repair plastic water closet seat cover, white, closed pattern with flat bottom including mild steel chromium plated or aluminised hinging device complete all as specified 106 s&f in repair vitreous china wash down closet pane (pedestal pattern white) standard size with s or p trap and other connecting items approved brand including fix with white cement complete all as specified make : jaquar (cat part no : lys wht 0314) or equivalent 107 s&f vitreous china water closet orissa pattern of size 580 x440mm white isi marked including provn of cement concrete bedding including connections to flushing cistern/pipe and making good disturbed portion to match existing surfaces complete all as specified 108 s&f in repair pvc white low level flushing cistern 10 ltr capacity with all fittings syphonic action push type with inlet ball valve and float including flush pipe long 32mm dia, ball valve, handle, bracket etc complete all as specified and directed 109 s&f in repair vitreous china counter wash hand basin oval shape of size 550x400mm including brackets, 32 mm cp waste coupling, chain and plug, waste fittings all necessary inlet and out let connections complete all as specified 110 s&f in repair vitreous china urinal, half stall type (back or corner wall type), white complete including providing and fixingplugs, bedding urinal against wall in cement mortar 1:2, securing urinal toplug with and including 60mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe grating and union for discharge pipe (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and as directed 111 s&f 15mm dia brass cp urinal spreader complete all as specified 112 s&f in repair pvc connection 15mm bore dia 450mm long with 2 nos ptmt nuts with washer complete all as specified 113 s&f 32 mm dia pvc flush pipe of polyethylene of low or high density for whb, sink, urinal complete all as specified and directed 114 s&f in repair chromium plated brass shower roses with or without swivel joints square type 125mm size including shower arm complete all as specified 115 s&f in repair health faucet (abs body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and abs wall hook including making connections and fixed in position complete all as specified and directed 116 s&f in repair toilet paper holder make : jaquar code acn-1153n or equivalent model inparryware /prayag / gem 117 s&f in repair towel ring round make : jaquar aqn -7721 or equivalent model in parryware /prayag / gem 118 s&f in repair 20 mm dia brass stainless steel tubular towel rail d type600mm long complete all as specified 119 s&f in repair tubular towel rail, brass, chromium plated, 20mm dia, d type, 60cm long between flanges, fixed in repairs complete all as specified and as directed make : jaquar cat part no aqn-7711 120 s&f in repair chromium plated soap dish of size 120x80mm, fixed to plugs with chromium plated brass screws complete all as specified 121 s&f in repair 15mm dia cast copper alloy chromium plated long body bib tap fancy type with wall flange complete all as specified 122 s&f in repair bib tap, brass, 15mm dia, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule complete all as specified and as directed make : jaquar cat part no con-107kn 123 s&f in repair two way bib cock, 15mm dia cast copper alloy chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule complete all as specified 124 s&f in repair 15mm dia cast copper alloy, chromium plated pillar tap long body swan neck type with fly nut capstan head screwed for 15mm bore dia of pipe complete all as specified 125 s&f in repair 15mm stop valve angle cock cast copper alloy, fancy type, chromium plated with long shunk and cup high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified 126 s&f in repair angular stop cock, 15mm dia, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for unions complete all as specified and as directedmake : jaquar cat part no con-053kn or equivalent in prayag / leader / zoloto 127 s&f in repair 15mm concealed type angle cock cast copper alloy,fancy type, chromium plated with long shunk and cup high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified 128 s&f in repair whb mixer, 15mm dia, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, with long shank with central hole screwed down, screwed both ends for iron pipe or for unions complete all as specified and as directed make : jaquar cat part no con-167knb equivalent in prayag / leader / zoloto 129 s&f in repair cp brass hot and cold 15mm dia wall mixture 3-in-1 system with provision for both hand shower and overhead shower complete with 115mm long bend pipe, connecting leg and wall flange complete all as directed. make : jaquar cat part no : con-281kn or equivalent model in parryware/prayag / gem 130 s&f in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm complete all as specified 131 s&f in repair sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified 132 s&f in repair 100mm size, 4 levers brass mortice lock, vertical type complete all as specified 133 demolition stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed 134 m&l 14-16mm granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. 135 dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed 136 m&l for light shade vitrified ceramic tiles minimum 8mm thick (square/ rectangular) polished area of each tiles n. exc 0.36 sqm (600x600mm) in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:4 complete all as specified and directed 137 m&l for light shade vitrified ceramic tiles minimum 8mm thick (square/ rectangular) polished area of each tiles n. exc 0.36 sqm (600x600mm) in vertical surfaces such as skirting, dados and riser etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick screed bed of cement mortar 1:3 complete all as specified and directed 138 m&l for non skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tiles exc 0.18 sqm but n. exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:4 complete all as specified and directed 139 m&l for non skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tiles exc 0.18 sqm but n. exc 0.36 sqm in skirting/dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick screed bed of cement mortar 1:3 complete all as specified and directed 140 m&l for non skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tiles exc 0.06 sqm but n. exc 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:4 complete all as specified and directed 141 m&l for non skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tiles exc 0.11 sqm but n. exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:4 complete all as specified and directed 142 m&l for coloured glazed ceramic tiles in vertical surfaces 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement over and including 10mm thick rendering or bedding layer of cement mortar 1:3 complete all as specified and directed 143 dismantling of wallandceilingboards(fibre, pulp, insulation etc) or insulationboards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed 144 m&l anodized aluminium snap grid framework incl 4 mm thick non asbestos fibre cement building boards 600x600mm incl two coats obd and preparation of surfaces over boardinserted to framework with screws with hangers 6mm dia gi (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of gi flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed 145 m & l for seamless gypsum board false ceiling 12mm thick including for any sunk or raised moulding with 25mm long self drilling/ tapping screws having philipshead with joining compound and 48mm wide fiber tape to provide seam less finish and including gi frame work of seamless ceiling comprising of gi perimeter channel 0.55mm thick with two unequal flangeof 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm c/c intermediate channel 0.9mm thick having two equal flanges of 15mm suspended from soffit at approx 900mm c/c with gi cleats and steel expansion fasteners with and incl ceiling section ( not exc 1.2m length) of 0.55mm thick having kurled web of 50mm an flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting across the intermediate channel at 457mm c/c incl hangers 6mm dia gi adjusting level fixed to roof slabs by means of ceiling cleats made out of gi flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete and finally applying two coats of oil bound distember with roller finish over a coat of primer complete all as specified and directed.