tender for office and reconstruction work under project alankar at rashtriya inter college, surir mathura - excavation in foundation in ordinary soil (loam, clay or sand) including lift upto 1.50 m and lead upto 30m and including filling watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the engineer in-charge upto a distance of 30m from the foundation trenches. as per s.i. no. 2.8.1 2 excavating, supplying, stacking and filling of local earth (excluding royalty) by mechanicaltransport upto a lead of 5km also including ramming and watering of the earth in layers notexceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift. as per si no. 2.25 (a) 3 providing and laying cement concrete in 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) and curing complete, including cost of form work. in foundation and floors. as per s.i. no.4.1.8 4 sand filling in plinth including supply of necessary quantity of sand from a distance not exceeding 8 kms. from the site of work and including watering, dressing etc rate to include cost of all materials labour t & p etc required for proper completion of work. as per s.i. no. 2.27 5 antitermite treatment of along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete: with chlorpyriphos / lindane e.c. 20% with 1 % concentration. as per chapter no. 8 sl no-2.35.3.1 6 providing and laying in position specified grade of reinforced cement concrete, excluding thecost of centering, shuttering, finishing and reinforcement - all work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-iii) derived from as per s.i. no. 5.1.2 7 r.c.c. work with cement approved coarse sand and 2cm (3/4) gauge approved stone ballast in the proportion 1:1.5:3 (1 part cement, 1.5 part coarse sand and 3 part of 2cm stone grit) in heavier beams excluding supply of reinforcement and its bending and including its fixing and binding the same with 24 bwgi binding wire and including necessary centering and shuttering etc and also including supply of all materials labour and tools and plants etc. required to proper completion of the work/strength of the concrete shell not be less than m-15 grade. as per s.i. no. 5.3 8 r.c.c. work with cement approved coarse sand and 2cm (3/4) gauge approved stone ballast in the proportion 1:1.5:3 (1 part cement, 1.5 part coarse sand and 3 part of 2cm stone grit) in column excluding supply of reinforcement and its bending and including its fixing and binding the same with 24 bwgi binding wire and including necessary centering and shuttering etc and also including supply of all materials labour and tools and plants etc. required to proper completion of the work/strength of the concrete shell not be less than m-15 grade. as per s.i. no.5.2.2 9 m.s. (t.m.t fe 500) in plain work such as rcc work including bending for proper shape and including supply of steel and its wastage, bends, hooks and authorised overlapping shall be measured and including cost of binding wire as per dsr si no-5.22.6 10 mild steel or iron work of small sizes and sections such as holding down bolts, hold fast tierods,gratings etc. ( when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. 10.31 11 class-150 brick work in 1:6 cement and coarse sandmortar in foundation and plinth including supply of all materials, labour and t&p etc. required for proper completion of the work. as per s.i. no. 6.1.2 12 painting on d.p.c. with two coats of air blown bitumen vg-10 grade @ 1.70kg/sqm approximate including cost of fuel if any. as per s.i. no. 4.13 13 class-150 brick work in 1:6 cement and coarse sandmortar in in super structure above plinth level upto floor five level (upto five stories) including necessary cutting and moulding of brick work as required and also including honey combed brick work in thickness of wall more than 12cm. add to above items. as per s.i. no. 6.4.2 14 15 mm thick cement plaster in 1:4 in single coat of fair side of single of half brick wall for interior plastering upto floor two level including internal rounded angles chamfers, and/or rounded angles not exceeding 80mm. in girth and finished even and smooth no. extra for mixing any additive. as per s.i. no. 13.5.2(interior surface). 15 12mm thick cement plaster in 1:6 in single coat of fair side of single of half brick wall for interior plastering upto floor two level including internal rounded angles chamfers, and/or rounded angles not exceeding 80mm. in girth and finished even and smooth no. extra for mixing any additive. as per s.i. no. 13.4.2 (outer side) 16 15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand) si-13.5.1 17 distempering (two coat) with oil bound distemper of approved brand and manufacture and of required shade on undercoated wall surface to give an even shade over & including a priming coat with cement primer of approved brand and manufacture such as berger, j&n, shalimar, asian, paints after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even with plaster of approved synthetic material and sand papered smooth including cost of all materials. as per s.i. no. 13.41.1 18 finishing walls with water proofing cement paint of approved make such as super snowcem, durocem, robiance, guttucem, supercem quality and of required shade on undecorated wall surface (two coat) over and including one coat white cement primer to give and even shade after thoroughly after brushing the surface for each coat of waterproof cement paint after the first coat to give an even shade. as per s.i. no. 13.46.1 19 painting two coat over priming coat (but excluding cost of priming coat) on steel and other metal surfaces upto 10cm width or girth or small articles not exceeding 0.10 sq.m. in area with superior synthetic enamel such as luxol 3, hi gloss apcolite, superlac, dulux specified brushing to give and even shade and including the cleaning the surface of all dirt, dust and other foreign matter sand papering and scrapping including cost of all materials, labour, tools and plants etc. required for proper completion of work. as per s.i. no. 13.62.1 20 painting two coat over priming coat (but excluding cost of priming coat) on on new wood surfaces upto 10cm width or girth or small articles not exceeding 0.10 sq.m. in area with superior synthetic enamel such as luxol 3, hi gloss apcolite, superlac, dulux specified brushing to give and even shade and including the cleaning the surface of all dirt, dust and other foreign matter sand papering and scrapping including cost of all materials, labour, tools and plants etc. required for proper completion of work. as per s.i. no. 13.48.2 21 centering and shuttering including strutting, propping etc. and removalof form for foundations, footings, bases of columns, etc. for mass concrete 5.9.1 22 centering and shuttering including strutting, propping etc. and removalof form for lintels, beams, plinth beams, girders, bressumers and cantilevers 5.9.5 23 centering and shuttering including strutting, propping etc. and removalof form for columns, pillars, piers, abutments, posts and struts 5.9.6 24 centering and shuttering including strutting, propping etc. and removalof form for suspended floors, roofs, slab, landing, balcony and access platform 5.9.3 25 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) non- decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including isi marked stainless steel butt hinges with necessary screws.(35mm thick single leaf). as per s.i. no. 9.21.2 26 providing and laying vitrified tiles in floor of 600x 600mm sizes (thickness 10mm), with water absorption less than 0.08% and conforming to is:15622, of approved brand & manufacturer, in desired colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to is : 15477, including grouting of joints.including 75 mm thick base with concrete 1:4:8 complete. as per chapter no 14 s.l. no.11.41.2 27 providing and laying vitrified tiles in floor of 600x 600mm sizes (thickness 10mm), with water absorption less than 0.08% and conforming to is:15622, of approved brand & manufacturer, in desired colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to is : 15477, including grouting of joints. in skirtin dado as per chapter no 14 s.l. no.11.46 28 supply of fixing first quality ceremic glazed tile in flooring or dado laid with 1:3 cement and approved coarse sand mortar finished with white cement jointed and polishing complete including supply of all materials, labour for proper completion of the work. as per s.i. no. 11.37a 29 providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestorywindows, all complete with :4.0 mm thick glass panes as per si no. 10.30.1 30 providing and fixing isi marked oxidised m.s. sliding door bolts with nuts and screws etc. complete (copper oxidised as per is 1378)(a) 250mm x 16 mm . as per si 9.62.1 31 prproviding and fixing isi marked oxidised m.s. tower bolt black finish, (barrel type) with necessary screws etc. complete (copper oxidised as per is 1378) (a) 250mm x 10mm. si 9.63.1 32 providing and fixing isi marked oxidised m.s. handles conforming to is:4992 with necessary screws etc. complete (copper oxidised as per is 1378)(a) 125 mm. as per si 9.66.1 33 providing and fixing isi marked oxidised m.s. tower bolt black finish, (barrel type) with necessary screws etc. complete (copper oxidised as per is 1378) (b) 200mm x 10mm. si 9.63.2 34 dismantling stone slab flooring laid in cement morter including stacking of serviceable material and disposal of unserviceable material with in 50m. lead as per dsr 15.25 35 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50m. lead as per dsr 15.56 36 dismantling doors, windows and ventilators including chawkhats, architrave, holdfasts etc. complete and stacking within 50m. lead as per dsr 15.12.1 37 providing and fixing water closet squatting pan (indian type w.c. pan) with 100 mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests 38 providing and fixing white vitreous china pedestal type water closet (european type w.c. pan) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to is : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required :w.c. pan with isi marked white solid plastic seat and lid 39 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required.(a)white vitreous china flat back wash basin size 550 x400 mm with single 15 mm c.p. brass pillar tap. 40 providing and fixing flexible p.v.c. waste pipe for sink or wash basin including pvc waste fittings complete. semi rigid pipe(a) 32mm dia 41 providing and fixing flexible p.v.c. waste pipe for sink or wash basin including pvc waste fittings complete. semi rigid pipe(b) 40mm dia 42 providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto 1 metre long with s.s. triangular plate to eureopean type w.c. of quality and make as approved by engineer - in -charge. 43 providing & fixing pvc pipes conforming to is make workinh pressure 6 kg/cm² including testing, labour, t&p and all complete fittings. 110mm dia 44 providing & fixing pvc pipes conforming to is make workinh pressure 6 kg/cm² including testing, labour, t&p and all complete fittings. 75mm dia 45 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. (internal work) exposed on wall 25mm dia nominal dia pipes 46 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. (internal work) exposed on wall 32mm dia nominal dia pipes 47 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. (internal work) exposed on wall 40mm dia nominal dia pipes 48 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. (internal work) concealed work, including cutting chases and making good the walls. 15mm dia nominal dia pipes 49 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. (internal work) concealed work, including cutting chases and making good the walls. 20mm dia nominal dia pipes 50 providing and fixing 45 cm long unplasticised pvc connection pipe with brass unions. (a) 15mm nominal bore 51 providing & fixing cp brass bib cock of approved quality conforming to is 8931(a) 15mm nominal bore 52 providing & fixing c.p. brass long body bib cock of approved quality conforming to is standards and weighing not less than 690 gms. (a) 15mm nominal bore 53 providing & fixing c.p. brass angle valve for basin mixer and gyser points of approved quality conforming to is 8931 (a) 15mm nominal bore 54 providing and fixing gun metal gate valve with wheel of approved quality. (a) 25mm dia nominal bore 55 providing and fixing gun metal gate valve with wheel of approved quality. (d) 32mm dia nominal bore 56 providing and fixing gun metal gate valve with wheel of approved quality. (e) 40mm dia nominal bore 57 providing and fixing brass stop cock of approved quality. (a) 15 mm nominal bore 58 providing and fixing brass stop cock of approved quality. (b) 20 mm nominal bore 59 providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 60 excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m.including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m. (a) pipes 80mm to 300mm diameter. 61 providing, laying and joining glazed stone ware pipes grade awith stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. (a) 100mm diameter 62 providing, laying and joining glazed stone ware pipes grade awith stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete (b) 150mm diameter 63 providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround s.w. pipes including bed concrete as per standard design. (a) 100mm diameters.w. pipe 64 providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround s.w. pipes including bed concrete as per standard design. (b) 150mm diameters.w. pipe 65 providing and fixing square-mouth s.w. gully trap grade‘a’ complete with c.i. grating, brick masonry chamber with water tight c.i. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design. 150 x 100 mm size p type 66 constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) rcc top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design inside size 90x80cms and 45cms deep including ci cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg). with fps bricks of class designation 7.5 (i) for sewer line 67 wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm frls pvc insulated copper conductor single core cable in surface / recessed medium class pvc conduit, with modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm frls pvc insulated copper conductor single core cable etc. as required. 68 wiring for circuit/ submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required. 2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire 69 wiring for circuit/ submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required. 2 x 4 sq. mm + 1 x 4 sq. mm earth wire 70 supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. 71 supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. 72 supplying and fixing suitable size gi box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 a modular socket outlet and 5/6 a modular switch, connections etc. as required. 73 supplyingandfixingsuitablesizegiboxwithmodularplateandcoverinfronton surfaceorinrecess,includingprovidingandfixing6pin5/6&15/16amodular socket outlet and 15/16 a modular switch, connections etc. as required. 74 supplying and fixing 3 pin, 5 a ceiling rose on the existing junction box/ wooden block including connections etc. as required. 75 supplying and fixing brass batten/ angle holder including connection etc. as required. 76 installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (up to 30 cm) with 1.5 sq. mm frls pvc insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. 77 supplying and fixing extra conduit down rod of 20 cm length g.l. pipe 15 mm dia, heavy gauge including painting etc. as required. (note : more than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored) 78 supply, installation, testing and commissioning of 1200 mm sweep, bee 5 star rated, ceiling fan with brush less direct current (bldc) motor, class of insulation: b, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, power factor not less than 0.9, service value (cm/m/w) minimum 6.00, air delivery minimum 210 cum/min , 350 rpm (tolerance as per is : 374-2019), thd less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree c (max.), insulation resistance more than 2 mega ohm, suitable for 230 v, 50 hz, single phase ac supply, earthing etc. complete as required. 79 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (but without mcb/rccb/lsolator)12 way double door 80 supplying and fixing 5 a to 32 a rating, 240/415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. single pole 81 supplying and fixing 5 a to 32 a rating, 240/415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. double pole 82 supply and fixing of 18-22w led tube light with extruded aluminium housing special polycarbonate diffuser for glare free light disribution and suitable mounting for both surface & suspended, complete in all respect. cat-aa 1980-2420 system lumens, 110lm/w, pf>0.95, thd <10% at full load, cri>80, with 3 years warrantee. 83 supply and burring of safe earthing electrode t-19, (hot dip galvanized), length up to 3000mm, outer dia 50 mm inner dia 25 mm, terminal dia 12mm, outer gi pipe of 16 swg and inner gi pipe of 12 swg with hot dip galvanization up to 100 micron filled with crystalline conductive mixture (ccm) having anti corrosive & conductive property with 50 kgs activated soil (bfc) capable of reducing the soil resistivity with good mixture of retaining capacity and one earthing lead of 25mm x 3mm g.i. strip, upto switch board (from apron to switch board, the cost of g.i. strip will be extra) along with 30 cm square c.i. frame with hinged cover & masonry housing. 84 supply & fixing of sign board including painting writing all complete