tender for construction of 17 nonresidential qtrs [type-ii/12, type-iii/02 & typ-iv/03] at rtc,itb police, sivagangai (tn); 1 earth work in excavation by mechanical means (hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. all kinds of soil. 2 extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. all kinds of soil. 3 excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :all kinds of soil. pipes, cables etc, not exceeding 80 mm dia. 4 excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :all kinds of soil. pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia 5 filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. 6 supplying chemical emulsion in sealed containers including delivery as specified.chlorpyriphos/ lindane emulsifiable concentrate of 20% 7 diluting and injecting chemical emulsion for post-constructional anti-termite treatment (excluding the cost of chemical emulsion) :2.35.3 treatment of soil under existing floors using chemical emulsion@ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 coarse sand) to match the existing floor:with chlorpyriphos/lindane e.c. 20% with 1% concentration 8 supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. 9 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level : 1:1½:3 (1 cement: 1½ coarse sand (zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 10 providing & applying a coat of residual petroleum bitumen of grade of vg-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil. 11 making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-iii) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. 12 providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana / ordinary portland /portland slag cement, admixtures in recommended proportions as per is: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: note: extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. in case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. all works upto plinth level. concrete of m25 grade with minimum cement content of 330 kg /cum. 13 providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana / ordinary portland /portland slag cement, admixtures in recommended proportions as per is: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: note: extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. in case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. all works above plinth level upto floor v level. concrete of m25 grade with minimum cement content of 330 kg /cum. 14 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-iii) : 3 graded stone aggregate 20 mm nominal size). 15 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.thermo-mechanically treated bars of grade fe-500d or more. 16 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.thermo-mechanically treated bars of grade fe-500d or more. 17 centering and shuttering including strutting, propping etc. and removal of form for all heights : foundations, footings, bases of columns, etc. for mass concrete 18 centering and shuttering including strutting, propping etc. and removal of form for all heights : suspended floors, roofs, landings, balconies and access platform 19 centering and shuttering including strutting, propping etc. and removal of form for all heights : lintels, beams, plinth beams, girders, bressumers and cantilevers. 20 centering and shuttering including strutting, propping etc. and removal of form for all heights : columns, pillars, piers, abutments, posts and struts 21 centering and shuttering including strutting, propping etc. and removal of form for all heights : weather shade, chajjas, corbels etc., including edges 22 brick work with clay flyash f.p.s. (non modular) brick of class designation 7.5 in superstructure above plinth level up to floor five level in : cement mortar 1:4 (1 cement : 4 coarse sand) 23 half brick masonry with non modular fly ash bricks of class designation 10, conformingio is :12894, in super structure above plinth and upto floor v level. cement mortar 1 : 3 (1 cement : 3 coarse sand) 24 providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. granite of any colour and shade area of slab upto 0.50 sqm 25 providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. granite of any colour and shade area of slab above 0.50 sqm 26 providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer-in-charge. granite work 27 extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. 28 extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location inmarble/ granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 29 providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).second class teak wood 30 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including isi marked stainless steel butt hinges with necessary screws 31 providing and fixing 1mm thick m.s. sheet door with frame of 40x40x6 mm angle iron and 3 mm m.s. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. using m.s. angels 40x40x6 mm for diagonal braces 32 providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with c.p. brass screws and pvc sleeves etc., wherever necessary complete :25 mm dia 33 providing and fixing m.s. grills of required pattern in frames of windows etc. with m.s. flats, square or round bars etc. including priming coat with approved steel primer all complete.fixed to openings /wooden frames with rawl plugs screws etc. 34 providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws 35 mm thick shutters with isi marked stainless steel butt hinges of required size second class teak wood 35 providing and fixing factory made single extruded wpc (wood polymer composite) solid door/window/ clerestory windows & desertory other frames/chowkhat comprising of virgin pvc polymer of k value 58-60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying pvc solvent cement and screwed with full body threaded star headed ss screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 n (face) & 1100 n (edge), minimum compressive strength of 58 n/mm2, modulus of elasticity 900 n/mm2 and resistance to spread of flame of class a category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with m.s hold fast/lugs/ss dash fasteners of required dia and length complete as per direction of engineer-in- charge. (m.s hold fast/lugs or ss dash fasteners shall be paid for separately). note: for wpc solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall. frame size 45 x 85 mm 36 providing and fixing factory made single extruded wpc (wood polymer composite) solid door/window/ clerestory windows & desertory other frames/chowkhat comprising of virgin pvc polymer of k value 58-60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying pvc solvent cement and screwed with full body threaded star headed ss screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 n (face) & 1100 n (edge), minimum compressive strength of 58 n/mm2, modulus of elasticity 900 n/mm2 and resistance to spread of flame of class a category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with m.s hold fast/lugs/ss dash fasteners of required dia and length complete as per direction of engineer-in- charge. (m.s hold fast/lugs or ss dash fasteners shall be paid for separately). note: for wpc solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall. frame size 65 x 100 mm 37 providing and fixing factory made single extruded wpc (wood polymer composite) solid decorative type flush door shutter of required size comprising of virgin polymer of k value 58-60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 n (face) & 900 n (edge), minimum compressive strength 50 n/mm2, modulus of elasticity 850 n/mm2 and resistance to spread of flame of class a category with property of being termite/borer proof, water/moisture proof and fire retardant. wpc to be laminated with pvc foil of minimum 14 microns thick of approved design pasted with hot melt adhesive onboth faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk s.s screws, all as per direction of engineer-in- charge. (note:stainless steel butt hinges and necessary s.s screws shall be paid separately) 35 mm thick 38 26.89 providing and fixing factory made single extruded wpc (wood polymer composite) solid board one side white color and other side of board laminted with pvc foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of k value 58-60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheathusk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 n (face) & 900 n (edge), minimum compressive strength 50 n/mm2, modulus of elasticity 850 n/mm2 and resistance to spread of flame of class a category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk s.s screws, all as per direction of engineer-in- charge. (note: stainless steel piano hinges/soft close clip on concealed hinges and necessary s.s screws shall be paid separately) 18 mm thick 39 providing and fixing factory made upvc glazed/wire mesh windows/ doors comprising of lead free upvc multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for series r1 and r2 profiles and 2.10 mm for series r3 and r4 profiles conforming to en: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per cpwd specification, upvc extruded glazing beads, interlocks and inline sash adaptor (where ever required) of appropriate dimension, epdm gasket, hardware, ss 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide pa6 grade sleeve for fixing frame to finished wall as per is 1367: part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all comers, including drilling of holes for fixing hardware and drainage of water etc. after fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to cpwd specification & direction of engineer-in-charge. section of steel reinforcement and cross sections of upvc profiles to be as per design approved by engineersin charge.wire mesh/glazing of plain/ toughened/ laminated/ double glass unit with/without high performance coatings as per design requirements and conforming to 15: 3548 & is: 16231 shall be paid separately. note:- structural design proof checked from a government engineering institute, to be provided by the manufacturer for fil sites with basis wind speed note:- structural design proof checked from a government engineering institute, to be provided by the manufacturer for:(i) sites with basic wind speed> 45m /sec as per is 875 part 3 (ii) sites with structure height more than 20m for all wind speedsmake fenesta/ncl veka/saintgobin.three track three panels sliding window with twoglazed & one wire mesh panels with aluminium channel for roller track, wool pile, nylon rollers with ss 304 body.using r3 series with frame (98 mm & above) x (40 mm & above) & both glazed and fly screen sash (30 mm & above) x (55 mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-pointlocking system. (height upto 1.8m).make fenesta/ncl veka/saintgobin. 40 providing and fixing factory made upvc glazed/wire mesh windows/ doors comprising of lead free upvc multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for series r1 and r2 profiles and 2.10 mm for series r3 and r4 profiles conforming to en: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per cpwd specification, upvc extruded glazing beads, interlocks and inline sash adaptor (where ever required) of appropriate dimension, epdm gasket, hardware, ss 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide pa6 grade sleeve for fixing frame to finished wall as per is 1367: part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all comers, including drilling of holes for fixing hardware and drainage of water etc. after fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to cpwd specification & direction of engineer-in-charge. section of steel reinforcement and cross sections of upvc profiles to be as per design approved by engineersin charge.wire mesh/glazing of plain/ toughened/ laminated/ double glass unit with/without high performance coatings as per design requirements and conforming to 15: 3548 & is: 16231 shall be paid separately. note:- structural design proof checked from a government engineering institute, to be provided by the manufacturer for fil sites with basis wind speed note:- structural design proof checked from a government engineering institute, to be provided by the manufacturer for:(i) sites with basic wind speed> 45m /sec as per is 875 part 3 (ii) sites with structure height more than 20m for all wind speedsmake fenesta/ncl veka/saintgobin. fixed window / ventilator with mullion / transom.using r4 series with frame (64 mm & above ) x (50 mm & above) & mullion (64 mm & above) x (70 mm & above). (height upto 0.90 metre) 41 providing and fixing zinc alloyed (white powder coated) touch lock for upvc sliding window with necessary screws etc. complete. 42 filling the gap in between aluminium/ stone/ wood frame and adjacent rcc / brick / stone / wood/ ceramic / gypsum work by providing weather /structural non sag elastomeric pu sealant over backer rod of approved quality as per architectural drawings and direction of engineer-in-charge complete, complying to astm c920, din 18540- f & iso 11600 upto 5 mm depth and 5 mm width 43 providing and fixing glazing in pvc / aluminum door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin- charge. (cost of aluminum snap beading shall be paid in basic item.)with float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) 44 providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete with 12 mm mild steel u beading 45 providing and fixing aluminium handles, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm 46 providing and fixing aluminium sliding door bolts, isi marked anodised (anodic coating not less than grade ac 10 as per is : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :300x16 mm 47 providing and fixing aluminium sliding door bolts, isi marked anodised (anodic coating not less than grade ac 10 as per is : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :250x16 mm 48 providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm 49 providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 200x10 mm 50 9providing and fixing aluminium hanging floor door stopper, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. twin rubber stopper 51 providing and fixing circular/ hexagonal cast iron or m.s. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick m.s. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ m.s. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. clamp shall be made of 12 mm dia m.s. bar bent to shape as per standard drawing. 52 providing and fixing stainless steel ( grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 53 providing and laying polished granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the engineer-in-charge. polished granite stone slab colour of black, cherry/ruby red or equivalent 54 providing and laying vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. the tiles must be cut with the zero chipping diamond cutter only . laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. glazed vitrified floor tiles polished finish of size size of tile 800 x 800 mm 55 providing and laying vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. the tiles must be cut with the zero chipping diamond cutter only . laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. glazed vitrified tiles matt/antiskid finish of size size of tile 600 x 600 mm 56 providing and laying vitrified tiles in different sizes (thickness to be specified by manufacturer ), with water absorption less than 0.08 % and conforming to i.s. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.size of tile 600x600 mm 57 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of stepsand dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 58 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion,(i) single socketed pipes.110 mm diameter 59 providing and fixing on wall face unplasticised - pvc moulded fittings/ accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion bend 87.5° 110 mm diameter 60 providing and fixing on wall face unplasticised - pvc moulded fittings/ accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion shoe (plain) 110 mm 61 providing and fixing unplasticised -pvc pipe clips of approved design to unplasticised - pvc rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with m.s. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement: 4 coarse sand) and making good the wall etc. complete. 110 mm 62 12 mm cement plaster of mix :1 : 4 (1 cement: 4 coarsesand) 63 15 mm cement plaster on the rough side of brick wall of mix : 1: 4 (1 cement: 4 coarse sand) 64 6 mm cement plaster of mix :1:3 (1 cement : 3 fine sand) 65 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 66 wall painting with premium acrylic emulsion paint of interior grade,having voc (volatile organic compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.two coats 67 applying priming coats with primer of approved brand and manufacture, having low voc (volatile organic compound ) content. with water thinnable cement primer on wall surface having voc content less than 50 grams/litre 68 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade : new work (two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 69 painting with synthetic enamel paint of approved brand andmanufacture to give an even shade : two or more coats on new work 70 grading roof for water proofing treatment with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 71 providing and fixing water closet squatting pan (indian type w.c. pan ) with 100 mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests 72 providing and fixing white vitreous china pedestal type water closet (european type) with seat and lid, 10 litre low level white vitreous china flushing cistern & c.p. flush bend with fittings & c.i. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :w.c. pan with isi marked white solid plastic seat and lid 73 providing and fixing wash basin with c.i. brackets, 15 mm dia cp brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the wallswherever required:-white vitreous china wash basin size 550x400 mm with a 15 mm cp brass single hole basin mixer 74 providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. 75 providing and fixing stainless steel a isi 304 (18/8) kitchen sink as per is:13983 with c.i. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : kitchen sink with drain board 510x1040 mm bowl depth 250 mm 76 providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto 1 metre long with s.s. triangular plate to eureopean type w.c. of quality and makeas approved by engineer - in - charge. 77 providing and fixing p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete. semi rigid pipe 32 mm dia 78 providing and fixing p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete. semi rigid pipe 40 mm dia 79 providing and fixing 600x450 mm beveled edge mirror of superior nglass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. 80 providing and fixing toilet paper holder : c.p. brass 81 providing and fixing ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. 82 providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with c.p. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. 83 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. concealed work, including cutting chases and making good the walls etc. 15 mm nominal dia pipes 84 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. external work - exposed on wall 32 mm nominal dia pipes 85 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. external work - exposed on wall 40 mm nominal dia pipes 86 providing and fixing gun metal gate valve with c.i. wheel of approved quality (screwed end) : 32 mm nominal bore 87 providing and fixing ball valve (brass) of approved quality, high or low pressure, with plastic floats complete : 25 mm nominal bore 88 providing and fixing gun metal non- return valve of approved quality (screwed end) : 40 mm nominal bore (vertical) 89 providing and fixing uplasticised pvc connection pipe with brass unions : 45 cm length 15 mm nominal bore 90 providing and fixing c.p. brass shower rose with 15 or 20 mm inlet :150 mm diameter 91 providingmaterial and labour forplacing on terrace (at all floor levels) polyethylene water storage tank isi : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 92 providing and fixing c.p. brass long nose bib cock of approved quality conforming to is standards and weighing not less than 810 gms.15 mm nominal bore 93 providing and fixing c.p. brass stop cock (concealed) of standard design and of approved make conforming to is:8931. 15 mm nominal bore 94 providing and fixing c.p. brass angle valve for basin mixer and geyser points of approved quality conforming to is:8931 15mm nominal bore 150 mm nominal size square 100 mm diameter of the inner hinged round grating 95 providing and fixing ptmt grating of approved quality and colour. rectangular type with openable circular lid 96 providing and fixing ptmt soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. 97 providing and fixing square- mouth s.w. gully trap class sp-1 complete with c.i. grating brick masonry chamber with water tight c.i. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 180 x 150 mm size p type with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 98 constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with r.c.c. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- iii) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- iii) : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :inside size 90x80 cm and 45 cm deep including c.i. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 99 extra for depth for manholes size 90x80cm with sewer bricks conforming to is : 4885 100 providing and laying non-pressure np2 class (light duty) r.c.c. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1;2 (1 cement : 2 fine sand) including testing of joints etc. complete: 150 mm dia. r.c.c. pipe 101 providing and laying non-pressure np2 class (light duty) r.c.c. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1;2 (1 cement : 2 fine sand) including testing of joints etc. complete: 250 mm dia. r.c.c. pipe 102 consultancy services for architectural, structural and mep services. i.e for carrying out of geo tech incesativation preparation of structural drawings,architectural drwaings, desining of mepdrawings and issuance good for construction drawings etc on stage wise for smoothful execution of works till finishing of project. 103 providing and fixing unplasticized poly vinyl chloride (upvc) swr pipes fittings type b for sewerage waste discharge system (is:13592 : 1992 marked) of approved quality /make supreme, jain pipes, sudhakar, prince or equivalent 100 mm dia 104 providing and fixing unplasticized poly vinyl chloride (upvc) swr pipes fittings type b for sewerage waste discharge system (is:13592 : 1992 marked) of approved quality /make supreme, jain pipes, sudhakar, prince or equivalent 75mm diameter : 105 providing and fixing unplasticized poly vinyl chloride (upvc) swr pipes fittings type b for sewarage waste discharge system (is:13592 : 1992 marked) of approved quality /make bend of required degree with access door,100 mm dia 106 providing and fixing unplasticized poly vinyl chloride (upvc) swr pipes fittings type b for sewarage waste discharge system (is:13592 : 1992 marked) of approved quality /make bend of required degree with access door,75 mm dia 107 providing and fixing unplasticized poly vinyl chloride (upvc) swr pipes fittings type b for sewarage waste discharge system (is:13592 : 1992 marked) of approved quality /make plain bend of required degree.100 mmdia 108 providing and fixing unplasticized poly vinyl chloride (upvc) swr pipes fittings type b for sewarage waste discharge system (is:13592 : 1992 marked) of approved quality /make. plain bend of required degree.75 mm dia 109 wiring for light point/ fan point/exhaust fan point/call bell point with 1.5 sq. mm frls pvc insulated copper conductor single core cable in surface/recessed medium class pvc conduit, with modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq. mm. frls pvc insulated copper conductor single core cable etc as required. group-c (primary point ) 110 wiring forgroup controlled (looping) light point /fan point / exhaust fan point/call bell point (without independent switch etc) with 1.5 sqmm frls pvc insulated copper conductor cable in surface/recessedpvc conduitand earthing the point with 1.5sqmm frls pvc insulated copper conductor single core cableetc.as required.group-c (looping point ) 111 wiring for twin control light point with 1.5 sq.mm frls pvc insulated copper conductor single core cable in surface / recessed medium class pvc conduit, 2 way modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm. frls pvc insulated copper conductor single core cable etc as required. 112 supplying and fixing suitable size gi box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (for light plugs to be used in non residential buildings). 113 supplying and fixing suitable size gi box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. 114 supplying & fixing suitable size gi box wih modular plate and cover in front on surface or in recess including providing and fixing 25 a modular socket outlet and 25 a modular sp mcb, c curve including connections, painting etc. as required. 115 wiring for circuit/ submain wiring along with earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required:2 x 1.5 sq. mm + 1 x 1.5 sq. mm earth wire for light extra loop. 116 wiring for circuit/ submain wiring along with earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required: 2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire for light circuit point 117 wiring for circuit/ submain wiring along with earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required: 2 x 4 sq. mm + 1 x 4 sq. mm earth wire for power circuit point 118 wiring for circuit/ submain wiring along with earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required: 4 x 10 sq. mm + 2 x 10 sq. mm earth wire for submain wire / cable of db 119 wiring for circuit/ submain wiring along with earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required::4 x 10 sq. mm + 2 x 6 sq. mm earth wire for submain wire / cable of db 120 supplying and installing following size of perforated pre-painted m.s. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with m.s. suspenders including bolts & nuts, painting suspenders etc as required:100 mm width x 50 mm depth x 1.6 mm thickness 121 supplying and installing following size of perforated pre-painted m.s. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with m.s. suspenders including bolts & nuts, painting suspenders etc as required: 150 mm width x 50 mm depth x 1.6 mm thickness 122 supplying and installing following size of perforated pre-painted m.s. cable trays bends with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with m.s. suspenders including bolts & nuts, painting suspenders etc as required.100 mm width x 50 mm depth x 1.6 mm thickness 123 supplying and installing following size of perforated pre-painted m.s. cable trays bends with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with m.s. suspenders including bolts & nuts, painting suspenders etc as required.150 mm width x 50 mm depth x 1.6 mm thickness 124 supplying and installing following size of perforated pre-painted m.s. cable trays reducers with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with m.s. suspenders including bolts & nuts, painting suspenders etc as required. 100 mm width x 50 mm depth x 1.6 mm thickness 125 supplying and installing following size of perforated pre-painted m.s. cable trays reducers with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with m.s. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width x 50 mm depth x 1.6 mm thickness 126 supplying and installing following size of perforated pre-painted m.s. cable trays tee’s with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with m.s. suspenders including bolts & nuts, painting suspenders etc as required. 100 mm width x 50 mm depth x 1.6 mm thickness 127 supplying and installing following size of perforated pre-painted m.s. cable trays tee’s with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with m.s. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width x 50 mm depth x 1.6 mm thickness 128 supplying and installing following size of perforated pre-painted m.s. cable trays cross members with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with m.s. suspenders including bolts & nuts, painting suspenders etc as required.100 mm width x 50 mm depth x 1.6 mm thickness 129 supplying and installing following size of perforated pre-painted m.s. cable trays cross members with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with m.s. suspenders including bolts & nuts, painting suspenders etc as required.100 mm width x 50 mm depth x 1.6 mm thickness 150 mm width x 50 mm depth x 1.6 mm thickness 130 supplying and fixing following way, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 v, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (but without mcb/rccb/isolator) 8 way (4 + 24), double door 131 supplying and fixing 5 amps to 32 amps rating, 240/415 volts, “c” curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with onnections, testing and commissioning etc. as required. single pole (6/32 amps) 132 supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (rccb), having a sensitivity current 30 ma in the existing mcb db complete with connections, testing and commissioning etc. as required. 40 a 133 supplying and fixing following rating, four pole, 415 volts, isolator in the existing mcb db complete with connections, testing and commissioning etc. as required. 63 amps 134 supplying and fixing single pole blanking plate in the existing mcb db complete etc. as required. 135 supplying and fixing of following sizes of medium class pvc conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20mm 136 supplying and fixing of following sizes of medium class pvc conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25mm 137 supplying and fixing of following sizes of medium class pvc conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32mm 138 supply, fixing, connecting and testing of elephone/computer/tv modular sockets modular plate anodised ms box and blanking late in surface/recessedincluding connectionetc as required. telephonic socket outlet 139 supply, fixing, connecting and testing of elephone/computer/tv modular sockets modular plate anodised ms box and blanking late in surface/recessedincluding connectionetc as required.tv antenna socket outlet 140 supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. 141 supplying and fixing modular blanking plate on the existing modular plate& switch box excluding modular plate as required.1 or 2 module 142 supplying and fixing folowing modular base & cover plate on exiting modualr metal boxes as etc as required 143 supplying and fixing 3 pin, 5 a ceiling rose on the existing junction box/ wooden block including connections etc. as required. 144 supplying and fixing call bell/ buzzer suitable for single phase, 230 v, complete as required. 145 supplying and fixing pvc batten/ angle holder including connections etc. as required. 146 supplying drawing, connecting and testing of 0.61mm dia annealed copper conductor pvc insulated pvc sheathed telephone wire/cables in existing pvc conduit or a racks as required. 2 pair telephone cable. (0.61sq mm) 147 supplying and fixing metal box of following sizes (nominal size) on surface or in reces with suitable size of phenolic laminated sheet cover in front including painting etc as required. 75 mm x 75 mm x 60 mm deep 148 earthingwithgipipe4.5mlongx40mmdiai/c accessoriesandprovidingmasonaryenclourewith cover palte having locking arrangement etc with charcoal or coke and salt complete etc as reqd. 149 providingandfixing25mmx5mmg.i.stripin40 mm dia g.i. pipe from earth electrode including connectionwithg.i.nut,bolt,spring,washer excavation and re-filling etc. as required 150 pdg.& fixing 25mmx5mm gi strip onsurface or in recess for connection etc. as reqd. 151 providing and fixing of lightning conductor finial, madeof25mmdia300mmlong,g.i.tube,having singleprongattop,with85mmdia6mmthickg.i. base plate including holes etc. complete as required. 152 jointing copper/ g.i. tape (with another copper/g i tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required. 153 providing and fixing g.i. tape 20 mm x 3 mm thick on parapetorsurfaceofwallforlightningconductor complete as required. (for horizontal run) 154 providing and fixing g.i. tape 20 mm x 3 mm thick on parapetorsurfaceofwallforlightningconductor complete as required. (for vertical run) 155 supply, installation, testingand commissioning of 1200mmsweep,bee5starrated,ceilingfanwith brush less direct current (bldc) motor, class of insulation:b,3nos.blades,30cmlongdownrod,2 nos.canopies,shacklekit,safetyrope,copper winding, power factor not less than 0.9, service value (cm/m/w) minimum 6.00, air delivery minimum 210 cum/min , 350 rpm (tolerance as per is : 374-2019), thdlessthan10%,remoteorelectronicregulator unitforspeedcontrolandallremainingaccessories includingsafetypin,nutbolts,washers,temperature rise=75degreec(max.),insulationresistancemore than2megaohm,suitablefor230v,50hz,single phase ac supply, earthing etc. complete as required. 156 led down lighter (smd type) (system lumen efficacy ≥120<135lm/watt) supplying, installation, testing & commissioning of led recessed/surface down lighter (round/ square/ rectangular) smd type of following body material with pmma and prismatic diffuser and construction as per is : 10322 with driver as per the requirement with driver efficiency >85%, operating voltage ac 140-270 volt, frequency 50/60 hz, operating temp range -5 0c to 400c centigrade, internal surge protection of 2.5 kv with short & open circuit protection ,thd < 10%, p. f.≥0.95, ip20, cri >80, ugr (unified glare rating) <19, flicker free (flicker should be below 5 %), life time (led, driver & electrical circuitry), life time of minimum 50000 burning hours with 70% of initial lumen maintained till life ends, cct 3000°k / 4000°k / 5700°k /6500°k (as per ansi bin), sdcm(standard deviation color matching) <3, maximum power consumption should not more than the specified rating and fixture shall be of relevant bis standard. manufactures word mark/ name engraved/ embossing/ screen printing on housing complete in all respect i/c external connections with 1.5 sq mm frls/hffr, pvc insulated copper conductor single core cable and earthing etc. as required with minimum 5 year oem warranty. system lumen efficacy ≥120 <135 lm/watt output . lm79 & lm80 test report and all testing required for led fixtures as per bis shall be submitted.. shape size and cct shall be as approved by engineer-in- charge as per requirement. (thermal management: heat sink of aluminum housing such that led junction temperature shall not rise above 90°c).powder coated die powder coated die cast /extruded aluminums body including trim .22 watt 157 led batten light (system lumen efficacy ≥120 <135 lm/watt) supplying, installation, testing & commissioning of led surface mounted batten light of following body material and construction as per is : 10322 with driver (replaceable) as per the requirement with driver efficiency >85%, operating voltage ac 140- 270 volt, frequency 50/60 hz, operating temp range -5 0c to 40 0c, internal surge protection of 2.5 kv with short & open circuit protection ,thd < 10% , p. f.≥0.95, ip20, cri >80, flicker free (flicker should be below 5 %), life time (led,driver & electrical circuitry), of minimum 50000 burning hours with 70% of initial lumen maintained till life ends, cct 3000°k / 4000°k / 5700°k /6500°k (as per ansi bin), sdcm(standard deviation colour matching) <3, maximum power consumption should not more than the specified rating and fixture shall be of relevant bis standard. manufactures word mark/ name engraved/ embossing/ screen printing on housing. complete in all respect i/c external connections with 1.5 sq.mm frls/hffr, pvc insulated copper conductor single core cable and earthing etc. as required with minimum 5 year oem warranty. system lumen efficacy ≥120 <135 lm/watt output . lm79 & lm80 test report and all testing required for led fixtures as per bis shall be submitted. shape size and cct shall be as approved by engineer-in-charge as per requirement. (thermal management: heat sink of aluminium housing such that led junction temperature shall not rise above 90°c). powder coated crca sheet body (thickness > 0.50 mm). 40 watt 158 supply ,fixing , testing and commissioning of exhaust fan of 300 mm. all accessories as required. 159 supply ,fixing , testing and commissioning of 2 ft mirror light. all accessories as required. 160 supplying, installation, testing and commissioning of powder coated, 14 swg crca sheet steel enclosed 11 kv h.t. metering panel complete with the following:i) 1set of 11/√3kv / 110/√ 3 volt, 100 va burden & accuracy class 0.2, single phase construction, dry type cast resin pt. over voltage factor: 1.2 continous ii) 3 nos. of dual core 60/5a, 15 va burden, accuracy class cl 0.5, 11 kv cast resin cts iii) one set of phase indicating lamps. iv) 1 sets of hrc fuses with fuse base (h.t. fuse - 1a & lt fuse 2-6a). v) 1 nos. indoor cable end box for suitable for 3c x 240 sq.mm. 11 kv(e), aluminium conductor xlpe ar. cable (incoming & outgoing cable).vi) space provision for 1 no.for seb approved digital trivector meter with mdi in kva of accuracy class - 0.2 for adjustment purpose in metering panel - outdoor duty metering cubicle with metering ct, pt, abt bi-directional meter as per local eb norms note: the contractor shall get the trivector meter, cts& pt tested by seb in requiredand the charges for liasioning for the same will be in contractor scope. rate inclusive ofsupply rate for metering panel as described above including installaion, commissioning for metering panel 161 supply , installation , testing and commissioning of cubical type floor mounted panel suitable for 415 v , 3 phase , 4wire 50 hz ac supply system of minimum depth 300mm fabricated in compartmentalized design from crca sheet steel of 3mm. thick for frame work and covers , 3mm thick for gland plate i/c cleaning complete with 7 tank process for powder coating in approved shade , having 150 amp capacity extensible type tpn aluminium alloy bus bars of high conductivity , dmc / smc bus bar supports ,with short circuit withstand capacity of 31 mva for 1 set . with 2 no. earth stud , solid connections from main bus bar to switch gears with required size of al. bus bar making interconnection etc providing and fixingfollowing switch gears :-(cable entry from bottom ) incoming :a) 63 amp 4 pole mccb with 25 ka breaking capity - 1 set . b) 3 nos. phase indication led lamps with 2 amp back up mcb , breaker on/off indicating light with 2 amp mcb ,test terminal block set circuit as per standard practic etc as required .bus bar :-100 amp. tpn al. extensible type outgoings :i) 16 / 20 amp 2 pole mcb - 10 ka -12 nos.ii) 20 amp industrial socket with 2 polemcb ( ip 66 )- 10 ka - 2 nos. iii) 70 amp tp contactor with no /nc contacts - 1 nos.iv) 24 hour time - 1 no. 162 supplying & laying of following 1100 voltgrade xlpe insulated extruded pvc sheathed aluminium conductor armoured cables as per specification in existing cable trays / pipe rack ,ducts, over bed of sand, clamped to wall with suitable clamps including, saddles fixing bolts, connecting testing and commissioning. 3.5 c x 95 sq. mm 163 supplying & laying of following 1100 voltgrade xlpe insulated extruded pvc sheathed aluminium conductor armoured cables as per specification in existing cable trays / pipe rack ,ducts, over bed of sand, clamped to wall with suitable clamps including, saddles fixing bolts, connecting testing and commissioning. 3.5 c x 70 sq. mm 164 supplying & laying of following 1100 voltgrade xlpe insulated extruded pvc sheathed aluminium conductor armoured cables as per specification in existing cable trays / pipe rack ,ducts, over bed of sand, clamped to wall with suitable clamps including, saddles fixing bolts, connecting testing and commissioning. 3.5 c x 50 sq. mm