tender for repairing of boundary wall and general miscellaneous civil works at 33kv s/s panchwati, jaipur - 1 part-a (bldg.) 2 1.1earth work in surface excavation not exceeding 30cm. in depth but exceeding 1.5 meter in width as well as10 sqm on plan including disposal of excavated earth up to 50 mtr. and lift up to 1.5 mtr. disposed soil to be levelled and neatly dressed : all kinds of soil 3 3.1.6 & 3.1.2 providing & laying in position cement concrete i/c curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering – all work up to plinth level.: (a) 1:4:8 (1 cement:4 course sand: 8 graded stone aggregate 40 mm nominal size). 4 m15 grade nominal mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stoneaggregate 20mm nominal size). 5 5.8.3/b-5half brick masonry in super structure, above plinth levelupto 5th level using bricks of designation 75 in cement mortar 1: 6 (1- cement: 6- coarse sand). 6 6.17.3/b-6supply and fixing in walls machine cut and polished stone shelves, tands and sills in cm 1: 3 with machine cut edges. kota stone minimum 30mm thick. 7 5.2.2/b-5brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level upto floor v level in all shapes and sizes in :cement mortar 1:6 (1- cement: 6- coarse sand). 8 12.3.2/b-12plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish: (a) 20mm thick 9 12.22.1providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete.(a)new plastered surface (three or more coats) 10 12.42/b-12finishing walls with acrylic smooth exterior paint of required shade including all scaffolding new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ). 11 12.46.2painting with synthetic enamel paint of approved brand and manufacture to give an even shade: (a) one or more coats on new work. 12 9.39providing and fixing of double leaf steel shutterfor cupboard, the frame is made of pressed steelisi section 80x25 mmx1.25 mm thickwith 1.00 mm ms sheet to spot welded including holdfasts of 15x3mm, ms oxidized fittings such as butt hinges, sliding doors bolts, handles, tower bolts and twin peg etc completeincluding applying priming coat of approved steel primer of red oxide zinc chromate andspray painting in approved shade with decopaint of approved quality complete as per direction of engineer in charge 13 16.56(a)providing and fixing stainless steel railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).grade 304 14 13.29repair to damaged rcc slabs, beams and columns etc for strengtheing with cement mortar 1 : 2 in following stepsi) choping losse and cracked concrete to required depth, cleaning the exposed surface of steel and concrete with wire brush and sand papering , cleaning of concrete surface with water as necessary and getting dried.ii) applying epoxy primer on the exposed steel bars.iii) applying epoxy hardener and resin mix (as per manufectureds specification) on concrete and steel bars with brush.iv)speading dry cement mortar 1 : 2 mix over epoxy treated wet surface and allow it to dry for one day.v) plastering the surface with cement sand mortar 1 : 3 upto depth of 30mm complete.vi) cure the plastered surface for 15 days all work including scaffolding etc. complete in all respect. 15 13.1repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead :with cement mortar 1 :4 ( 1 cement : 4 coarse sand) 16 13.23repair of existing steel glazed doors, windows and ventilator, ms sheet door, garge doors, compound wall gates etc. by welding drilling complete include. cost of welding rods and hire charge of welding meachine and tp etc complete 17 e 1.1.1wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694)inrecessed isi marked mms ( is:9537 p - iii ) virgin material pvc conduit & itsisi marked (is:3419-1988) accessories, round tiles, 1.2 mm thickhot dipped galvanized modular box with earth terminal, 10a modular switch,modular face plate with grid plate, 3 pin ceiling rose / holder /3 way connector, screws,making connections, testing etc. as required.for specification of copperconductor,phenolic laminated sheets & electrical/ wiring accessories refer chapter e - 04, e - 05 & e - 07 for additional technical parameters of product / work refer annexure a attached with this bsr(a) short point (up to 3 mtr.) 18 (b) medium point (up to 6mtr). (e1.1.2) 19 (c) long point (up to 10mtr).(e1.1.3) 20 e 1.3.1wiring of 3/5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade(is:694) inrecessed isi marked mms ( is:9537 p - iii ) pvc conduit & its isi marked (is:3419-1988)accessories, hot dipped galvanizedmodular box of 1.2 mm thick with earth terminal, 10 a modularswitch, 3/5 pin 6 a modular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor,phenolic laminated sheets & electrical/ wiring accessories refer chapter e - 04, e - 05 & e - 07 for additional technical parameters of product / work refer annexure a attached with this bsron board. 21 1.4.2s&f following sizes (dia.) of isi marked virgin material mms ( is:9537 p - iii ) pvc conduit along withisi marked (is:3419-1988) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. for additional technical parameters of product / work refer annexure a attached with this bsr25mm 22 e 4.1.7supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130/iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a/c/d , flame retardant as per is 10810-53, better amperage rating as per is:3961 part 5,in existingsurface or recessed pvc/ ms conduit/casing capping making connections with copper lugs of suitable size, ferrules,testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr(a) 2 x 2.5 sqmm.+ 1x1.5 sqmm. 23 (b) 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. (e 4.1.14) 24 7.36providing and fixing of power plug point with non modular accessories as per pwd specification for electrical works withgalvanized box of 1.2 mm thickwith earth terminal with suitable size phenolic laminated sheet (is : 2036 -1995) cover including cost of 16 amp. switch (is :3854) and 3/6 pin 16 amp. socket outletmaking connection , testing , etc. as required. . for specification ofwiring accessories refer chaptere - 07 related item &for additional technical parameters of product / work refer annexure a attached with this bsr 25 6.1.1.2providing & fixing of 240/415 v ac mcb with positive isolation of 10 ka breaking capacity (b/ c/d tripping characteristic as per type of load andsite requirement) 4 kv impulse withstand voltage, isi marked is 8828(1996) / conforming to iec 60898-1 2002, iec 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec,minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board/sheets, minimum electrical operation 20,000 upto 20 a rating and 10,000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 6a to 32 a rating.single pole mcb 26 6.2.1.2providing & fixing of 240/415 v isolatorisi marked is:13947-iii/conforming to iec 60947-3, suitable for ac22a utilization category, 4kv impulse withstand voltage,true contact indication,red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting,minimum phase termination capacity of 35sq.mm.ip 20 contact protection and fitted in existing distribution board / sheetincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr double pole isolator 63 a rating 27 6.10.1.3providing & fixing of recessed/surface mounting heavy duty horizontal type double door ( metal / glazed )distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is-8623-1 & 3 / iec 61439- 1 & 3, powder painted complete with reversible door (for double door db only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsrmetal door (single phase) ik-09 and ip-43 with metal end box8 way (8+2) 28 17.1.1providing & fixing of ip20 smd mid power led batten type integrated light fixture made from powder coated extruded aluminiumhousing with in built driver, system lumen efficacy ≥ 110 lm/watt output, internal surge protection of 2.5 kv with short & open circuit protection ,thd < 10% , p. f.≥0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k/ 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79 & lm80) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr .1170mm(+/-10%) led batten with min. lumen output 2200 lm 29 9.2/b-9structural steel work riveted,bolted or welded in built up sections, trusses and framed work, including cutting, hoisting (height upto 10 m) , fixing in position and applying a priming coat of approved steel primer all complete: 30 9.38.3providing and fixing welded mesh/expanded metal mesh in frame work, flat iron beading 20x3mm including top cross laps inside and out sides welding, iron bolts, crews, clips etc. complete (excluding frame work) of size.welded mesh 25 mmx 25 mm x 2.1 mm (9.38.3) 31 9.13supplying and fixing rolling shutters of approved make, made of 80 x 1.25mm. m.s. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including cost of spring hooks, providing and fixing necessary 25.3cm. long wire springs grade no. 2 and m.s. top cover 1.25mm thick for rolling shutters as per design & is 6248- 1979. (clear openable area to be measured for payment).