tender for renovation of sub division office, control room and general miscellaneous civil works at 33kv s/s pratap nagar, jaipur - 1 part-a (bldg.) 2 1.8earth work in excavation by mechanical means (hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.all kinds of soils 3 3.1.6 & 3.1.2 providing & laying in position cement concrete i/c curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering – all work up to plinth level.: (a) 1:4:8 (1 cement:4 course sand: 8 graded stone aggregate 40 mm nominal size). 4 6.1.6/b-6random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in: cementmortar 1:6 (1- cement: 6- sand). 5 12.3.2/b-12plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish: (a) 20mm thick 6 (b) 12mm thick (12.3.3) 7 12.22.1providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete.(a)new plastered surface (three or more coats) 8 12.37.1 /b-12distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding: (a) new work (two or more coats) over and i/c scrapping and priming coat with cement primer. 9 12.42/b-12finishing walls with acrylic smooth exterior paint of required shade including all scaffolding new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ). 10 12.46.1painting with synthetic enamel paint of approved brand and manufacture to give an even shade: (a) two or more coats on new work. 11 9.2/b-9structural steel work riveted,bolted or welded in built up sections, trusses and framed work, including cutting, hoisting (height upto 10 m) , fixing in position and applying a priming coat of approved steel primer all complete: 12 9.8/b-9providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 13 9.8.1/b-9extra if square,rectangular hollow tubularsections are used or grill made by flats only 14 (b) welded mesh 25 mmx 25 mm x 2.1 mm (9.38.3) 15 3.16.2 /s-3p & f rigid pvc pipe ( is: 4985 make) class ii/(4 kg./cm2). approved quality /make including jointing the pipe with solvent cement rubber ring and lubricant.(a) 75 mm dia 16 (b) 110mm dia. (3.16.3) 17 3.17.9/s-3p & f rigid pvc pipe fitting ( is: 4985 mark) of approved quality /make including jointing the pipe with solvent cement rubber ring and lubricant.(a) bend 87.5 75mm dia 18 (b) bend 87.5 110mm dia(3.179-ii) 19 3.20.1/s-3construction of man hole, in all types of soil, inner size 1.5 x 1.2 m, with 450mm thick masonry in cm 1:6, 10 cm. thick cement concrete 1:5:10 in foundation, 20mm thick inside plaster in cm 1:6, finished with floating neat cement, 50 mm thick m-15 grade c.c. flooring making channels, 80 mm thick stone slab covering with 40 mm thick m-15 grade c.c.flooring, ferro cement cover with frame of 450mm dia, earthwork etc. complete including disposal of surplus earth within 50 mtr. lead as per design depth up to 1.5 m : 20 3.22.3construction of soakage well in all type of soil with 300 mm thick dry masonry, top and bottom 300 mm course in cm 1:6, 80mm thick stone slab, jointing of slab in cm 1 : 3, ralthal, kharanja, 40 mm thick m-15 grade c.c flooring , earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr.:size 240 cm. dia outside & 240 cm. depth. 21 e 1.1.1wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694)inrecessed isi marked mms ( is:9537 p - iii ) virgin material pvc conduit & itsisi marked (is:3419-1988) accessories, round tiles, 1.2 mm thickhot dipped galvanized modular box with earth terminal, 10a modular switch,modular face plate with grid plate, 3 pin ceiling rose / holder /3 way connector, screws,making connections, testing etc. as required.for specification of copperconductor,phenolic laminated sheets & electrical/ wiring accessories refer chapter e - 04, e - 05 & e - 07 for additional technical parameters of product / work refer annexure a attached with this bsr(a) short point (up to 3 mtr.) 22 (b) medium point (up to 6mtr). (e1.1.2) 23 (c) long point (up to 10mtr).(e1.1.3) 24 e 1.3.1wiring of 3/5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade(is:694) inrecessed isi marked mms ( is:9537 p - iii ) pvc conduit & its isi marked (is:3419-1988)accessories, hot dipped galvanizedmodular box of 1.2 mm thick with earth terminal, 10 a modularswitch, 3/5 pin 6 a modular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor,phenolic laminated sheets & electrical/ wiring accessories refer chapter e - 04, e - 05 & e - 07 for additional technical parameters of product / work refer annexure a attached with this bsron board. 25 1.4.2s&f following sizes (dia.) of isi marked virgin material mms ( is:9537 p - iii ) pvc conduit along withisi marked (is:3419-1988) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. for additional technical parameters of product / work refer annexure a attached with this bsr25mm 26 e 4.1.7supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130/iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a/c/d , flame retardant as per is 10810-53, better amperage rating as per is:3961 part 5,in existingsurface or recessed pvc/ ms conduit/casing capping making connections with copper lugs of suitable size, ferrules,testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr(a) 2 x 2.5 sqmm.+ 1x1.5 sqmm. 27 (b) 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. (e 4.1.14) 28 7.36providing and fixing of power plug point with non modular accessories as per pwd specification for electrical works withgalvanized box of 1.2 mm thickwith earth terminal with suitable size phenolic laminated sheet (is : 2036 -1995) cover including cost of 16 amp. switch (is :3854) and 3/6 pin 16 amp. socket outletmaking connection , testing , etc. as required. . for specification ofwiring accessories refer chaptere - 07 related item &for additional technical parameters of product / work refer annexure a attached with this bsr 29 6.1.1.2providing & fixing of 240/415 v ac mcb with positive isolation of 10 ka breaking capacity (b/ c/d tripping characteristic as per type of load andsite requirement) 4 kv impulse withstand voltage, isi marked is 8828(1996) / conforming to iec 60898-1 2002, iec 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec,minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board/sheets, minimum electrical operation 20,000 upto 20 a rating and 10,000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 6a to 32 a rating.single pole mcb 30 6.2.1.2providing & fixing of 240/415 v isolatorisi marked is:13947-iii/conforming to iec 60947-3, suitable for ac22a utilization category, 4kv impulse withstand voltage,true contact indication,red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting,minimum phase termination capacity of 35sq.mm.ip 20 contact protection and fitted in existing distribution board / sheetincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr double pole isolator 63 a rating 31 6.10.1.3providing & fixing of recessed/surface mounting heavy duty horizontal type double door ( metal / glazed )distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is-8623-1 & 3 / iec 61439- 1 & 3, powder painted complete with reversible door (for double door db only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsrmetal door (single phase) ik-09 and ip-43 with metal end box8 way (8+2) 32 11.38.1m-30, 60 mm thick to be used in non traffic areas like building premises, monument premises, land scapes, public gardens/ park, domestic drives, paths and patios, embankment slopes, sand stabilization area etc.( as per table 1 ofis 15658:2006category a denated units to key into each other on four faces zigzag shape as per irc sp 63:2004