tender for construction of 250 mt warehouse-2 excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (lift upto 0.00 to 1.50 m.) by mechanical means 3 filling in plinth and floors with contractors material/brought from outside and approved by engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete. 4 providing and laying cast in situ/ready mix cement concrete in m-10 of trap/ granite / quartzite / gneiss metal for foundation and bedding including bailing out water, steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based plc with scada enabled reversible drum type mixer/concrete batch mix plant (pan mixer) etc. complete. with fine aggregate (crushed sand vsi grade) 5 providing preconstructional antitermite treatment as per i.s. 6313 (part-ii) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper. 6 providing and laying cast in situ/ready mix cement concrete m- 20 of trap / granite /quartzite/ gneiss metal for r.c.c. work in foundations like raft, strip foundations, grillage and footings of r.c.c. columns and steel stanchions etc. including bailing out water, steel centering, formwork ,cover blocks, laying/pumping, compaction and curing roughening the surface if special finish is to be provided (excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based plc with scada enabled reversible drum type mixer/ concrete batch mix plant (pan mixer) etc. complete. with fine aggregate (crushed sand vsi grade) 7 providing and laying cast in situ/ready mix cement concrete in m-20 of trap/ granite/ quartzite/ gneiss metal for r.c.c. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (excluding reinforcement and structural steel).with fully automatic micro processor based plc with scada enabled reversible drum type mixer/ concrete batch mix plant (pan mixer) etc. complete. with fine aggregate (crushed sand vsi grade) 8 providing and laying in situ /ready mix cement concrete m-20 of trap / granite /quartzite/ gneiss metal for r.c.c. work in foundations like raft, strip foundations, grillage and footings of r.c.c. columns and steel stanchions etc. including bailing out water, steel centering formwork, laying/pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided (excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based plc with scada enabled reversible drum type mixer/ concrete batch mix plant (pan mixer) etc. complete. with fine aggregate (crushed sand vsi grade) 9 providing and laying cast in situ/ready mix cement concrete m-20 of trap/ granite / quartzite/ gneiss metal for r.c.c. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(excluding reinforcement and structural steel).with fully automatic micro processor based plc with scada enabled reversible drum type mixer/ concrete batch mix plant (pan mixer) etc. complete. with fine aggregate (crushed sand vsi grade) 10 providing and laying cast in situ/ready mixcement concrete m-20 of trap/ granite/ quartzite/ gneiss metal for r.c.c. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (excluding reinforcement and structural steel). with fully automatic micro processor based plc with scada enabled reversible drum type mixer/ concrete batch mix plant (pan mixer) etc. complete. with fine aggregate (crushed sand vsi grade) 11 providing and fixing in position tmt - fe - 500 bar reinforcement of various diameters for r.c.c. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. 12 providing second class burnt brick masonry with conventional/ i.s. type bricks in cement mortar 1:6 in foundations and plinth of inner walls/ in plinth external walls including bailing out water manually , striking joints on unexposed faces, raking out joints on exposed faces and watering etc. complete 13 providing second class burnt brick masonry with conventional/ i.s. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. complete 14 providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. 15 providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. 16 providing and applying white-wash in two coats on old / new plastered or masonry surfaces and asbestos cement sheets including scaffolding and preparing the surface by brushing and brooming down etc. complete. 17 providing and applying colour-wash of approved colour and shade in one coat to new surface including scaffolding, brushing and brooming down (excluding base coats of white wash) etc. complete. 18 providing and laying in situ cement concrete m20 with tremix treatment for 100mm thickness for flooring with groove cutting of 4mm wide and 20mm deep with necessary refilling with bitumen etc. complete. 19 providing structural steel work in trusses, other similar trussed purlins and members with all bracing, gusset plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting fixing in position, making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it 2 coats of oil painting approved quality and shade etc. complete. 20 providing and fixing 45 cm wide mild steel ladder of 40mm x 6 mm mild steel flat stringers and steps of 18 mm dia. mild steel bar for water tank including fixing it in (1:2:4) m-15 cement concrete block 60cm x 30cm x 30cm and painting the ladder complete. (anti corossive paint) 21 providing and fixing corrugated galvanised iron sheets of 0.63 mm thick (24 b.w.g.) for roofing without wind tiles including fastening with galvanised iron screws and bolts, lead and bitumen washers as per drawing etc. complete. (weight of 5.5 kg / sqm.) 22 providing and fixing of colour coated zincaluminium( r ) az150 ( min 150 gms/sq.mt. total on each side ) profiled sheets for roofing. the feed material is manufactured out of nominal 0.45 mm base metal thickness ( bmt ) (0.5 mm tct ), hi-strength steel withmin.550 mpa yield strength, metallic hot dip coated withaluminium-zinc alloy (55% aluminiumm 43.4% zinc 1.6% silicon) with colorbond ( r ) steel quality super durable polyster paint coat ( with inorganic pigment). the paint shall have a total coatingthickness of nominal 35 mm, comprising of nominal 25mmexterior coat on top surface and nominal 10 um reverse coat on back surface. profile sheet shall have nom. 950-1050 mm effective cover width and nominal 25-30 mm deep ribs with sublet square fluting inthe five pan at nominal 180-250 mmcenter- to-center. the end rib shall be designed for anti-capacity groove. and return leg. the feed material should have coil manufacturers product details marked a regular interval. including fasteners with min. fastened with min. 25 um zinc-tin alloy coated, hex head, self-drilling screw etc. complete. (weight of profile 4.52 kilogram/ one square metre) 600 mm girth (surface width). 23 providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9 mm with lock plate of 3.15 mm thickness reinforced with 35 x 35 x 5 mm angle section fitted with sliding bolts and handles for both sides, deep m.s. channel section of depth and thickness not less than 65 mm and 3.15 mm respectively with hold fast arrangements, m.s. bracket plate 300 x 300 x 3.15 mm minimum size and shape with square bar, suspension shaft of minimum 32 mm diameter, hood cover of m.s. sheet not less than 0.9 mm thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc. complete. (i.s. 62481979) (with mechanical gear) 24 providing and fixing steel window of various sizes as per detailed drawing without hot dip zinc coating, without ventilators, including fabricating / glazing with plain / obscured glass panels of approved type and quality, iron oxidised fixtures and fastenings, finishing with oil painting two coats complete (with guard bars 12 mm square at 10 cm c/c.) 25 supply & fixing of turbo ventilator with 610 mm throat, having base ring & top plate in stainless steel of 0.8 mm thick, rotated using twin bearings of skf - 600122 & 600322 permanently lubricated & sealed. fixed in frp base plate of2mm thk clear 1.020 mtr wide & 1.7 mtr long. 26 supplying and erecting mains with 3 x 2.5 sq.mm frlsh copper pvc insulated wire laid in provided conduit / trunking / inside pole / bus bars or any other places as per specification no: wg-ma/bw 27 supplying and erecting led panel light (600mm x 600mm) max. 30 having crca powder coated housing, polystyrene diffuser having system lumens output of min. 3600 lumens, min. efficacy of 120 lumen/w, cri>80, cct upto 6500k, beam angle of 120 deg., max. ripple of 5%, thd<10%, p.f. >0.95, operating range of 120-270v, surge protection of 2.5 kv, life class of 50,000 hrs. at l70b50 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty. 28 point wiring in for light/fan/bell in 20 mm metal conduit with 1.5 sq.mm (2+1e) frlsh grade copper wire, flush type switch, earthing and required accessories as per specification no: wg-pw/sw 29 supplying and erecting steel tubular swaged pole 139.7 x 114.3 x 88.9 mm dia with 4.5x3.65x3.25 mm thickness (4.5 + 1.75 + 1.75 m) length respectively and total 8.0 m long with pole cap, base plate in provided foundation. (weight 101 kg) as per specification no. oh- pl/stp 30 providng earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. ea-ep 31 providing pipe type earthing with 40mm. dia. g.i. pipe or 20 mm dia. g.i. rod complete with all materials testing and recording the results as per specification no. ea-ep 32 supplying, erecting & marking dp-mcb 6a to 32a, c-series with rated short - circuit breaking capacity (icn) 10ka in provided distribution board as per specification no. sw-swr/mcb 33 supplying, erecting & marking dp-mcb 6 a to 32 a, b-series with rated short - circuit breaking capacity (icn) 10ka in provided distribution board as per specification no. sw-swr / mcb 34 supplying and erecting gi sheet 1.6 mm (16 swg) having zinc coating of 350 microns with galvanization process compliance to is 2629:1985 to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint. 35 supplying and erecting marine (waterproof) plywood 18/19 mm thick fixed to wall or on provided panel board with necessary materials such as screws, wall fasteners, supports, nut bolts etc. complete with compliance to is 720:2010 36 wiring for plug on board with switch socket surface/concealed type, copper wiring and earthing and with modular accessories as per specification no: wg pw/cw 37 supplying and erecting regular/ standard model ceiling fan of 900 /1050 mm. sweep complete erected in position as per specification no. fg-fn/cf 38 supplying, erecting and marking double pole isolator only switch version of miniature circuit breaker of 40a with required wiring connections and lugs etc. in provided distribution board. 39 material testing cement - fineness, standard consistency, setting time (initial & final ), compressive strength, soundness 40 concrete m-25 - mix design with all tests on basic materials 41 concrete m-25, m20 and m-10 grade - concrete compressive strength 42 crushed metal - water absorption, specific gravity,impact value,crushing value 43 brick - crushing value, water absorbation, & specific gravity 44 steel - tensile strength ,yield stress, ultimate tensile stress, %elongation, weight per running meter,bend/rebend test.(set of 3 bars) 45 murum - plasticity index & murum - field density of compacted layer 46 sand test -sieve analysis & sand test -silk connect test 47 royalty charges sand 48 other than sand material 49 prviding and managing 20 trees in the same premises, under management strategies and implementation plan ( msip ) to manage environmental , social , health and safety. please enable macros to view boq information