tender for civil work, improvement/renovation of mh haiderpur as per ayam at haiderpur ward no. c-55 shalimar bagh-4 3 demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer in - charge. nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge. in cement mortar demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of engineer - in-charge. 18 dismantling dism steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. 10 5.25 dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. 15.56 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 1 14.1 repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of engineer-in-charge. 14.1.2 with cement mortar 1:4 (1cement: 4 coarse sand) 4.1 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level: 4.1.10 1:5:10 (1 cement: 5 coarse sand (zone-iii) derived from natural sources: 10 graded stone aggregate 40 mm nominal size derived from natural sources) 11.26 kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, induding rubbing and polishing complete with base of cement mortar 1: 4 (1 cement: 4 coarse sand): 11.26.1 25 mm thick kota stone slabs 20 mm thick in risers of steps skirting, dado and pillars laid on 12 mm (average thick cement mortar 1:3 (1 cement: 3 coarse sand and jointed with grey cement slurry mixed wit pigment to match the shade of the slabs, including rubbing and polishing complete. providing and laying vitrified floor tiles in differen sizes (thickness to be specified by the manufacturer with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 2 size of tile 600x600 mm providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to is: 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand), jointing with grey cement slurry@ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. form work 5.9 centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconiles and access platform providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement -all work up to plinth level: 1:1.5:3 (1 cement: 1.5 coarse sand (zone-iii) derived from natural sources 3 graded stone aggregate 20 mm nominal size de rived from natural sources) steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo-mechanically treated bars of grade fe-500d or more providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. distempering with oll bound washable distemper of approved brand and manufacture to give an even shade: new work (two or more coats) over and including water thinnable priming coat with cement primer providing and fixing isi marked flush door shutters conforming to is: 2202 (part i) non-decorative type, core of block board construction with frame of ist class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including isi marked stainless steel butt hinges with necessary screws providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, faclas and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to igive high gloss finish etc. complete at all levels granite stone slab colour black, cherry/ruby red area of slab over 0.50 sqm applying priming coat: with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) painting with synthetic enamel paint of approved brand and manufacture to give an even shade: two or more coats on new work providing and laying 75 mm thick compacted bed of dry brick aggregate of 40 mm thick nominal size including spreading, well ramming, consolidating and grouting with jamuna sand, including finishing smooth etc. complete as per direction of engineer in-charge. 1:12:3 (1 cement: 1½ coarse sand (zone-iii) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources) brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in: cement mortar 1:4 (1 cement: 4 coarse sand) half brick masonry with common burnt clay f.p.s.. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level. cement mortar 1:4 (1 cement: 4 coarse sand) mirror polishing on marble work/granite work/stone work where ever required to give high gloss finish complete providing and fixing isi marked oxidised m.s. sliding door bolts with nuts and screws etc. complete: 300 x 16 mm providing and fixing isi marked oxidised m.s. tower bolt black finish, (barrel type) with necessary screws etc. complete: 250x10 mm providing and fixing isi marked oxidised m.s. handles conforming to is:4992 with necessary screws etc. complete: 125 mm providing and fixing aluminlum hanging floor door stopper, isi marked, anodised (anodic coating not less than grade ac 10 as per is: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. twin rubber stopper providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works providing and fixing factory made isi marked steel glazed doors, windows and ventilators, side/top /centre hung, with beading and all members such as f7d,f4b, k11 b and k12 b etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of c.c. 1:3:6 (1) cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. hot finished welded type tubes providing and fixing stainless steel (grade 30 ralling made of hollow tubes, channels, plates et including welding, grinding, buffing, polishing a making curvature (wherever required) and fitting t same with necessary stainless steel nuts and bo complete, l/c fixing the ralling with necessa accessories & stainless steel dash fasteners, stainle steel bolts etc., of required size, on the top of th floor or the side of waist slab with suitab arrangement as per approval of engineer-in charge, (for payment purpose only weight of stainless ste members shall be considered excluding fixin accessories such as nuts, bolts, fasteners etc.). providing & fixing uv stabilised fiberglass reinforce plastic sheet roofing up to any pitch, including fixin with polymer coated j or l hooks, bolts & nut 8mm dia. g.i plain/bitumen washers complete bu excluding the cost of purlins, rafters, trusses etc. the sheets shall be manufactured out of 2400 tex pane rovigs incorporating minimum 0.3% ultra-viole stabiliser in resin system under approximately 2400 psi and hot cured. they shall be of uniform pigmentation and thickness without alr pockets and shall conform to is 10192 and is 12866. the sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 12 mm thick flat 12 mm cement plaster of mix: 1:4 (1 cement: 4 coarse sand) providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with: 4.0 mm thick glass panes providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia m.s. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with m.s. tubes, m.s. tube challies, m.s. clamps and m.s. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after the scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of engineer in-charge the elevational area of the scaffolding shall be measured for payment purpose the payment will be made once irrespective of duration of scaffolding. note: this item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done, providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. lettering with black japan paint of approved brand and manufacture 1 2 1 4 1 1 0 providing and fixing concertina coll fencing with punched tape concertina coll 600 mm dia 10 metre openable length (total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron y shaped placed 2.4m or 3.00 m apart and with 9 horizontal r.b.t. reinforced barbed wire, stud tied with g.i. staples and g.i. clips to retain horizontal, including necessary bolts or g.i. barbed wire tied to angle iron, all complete as per direction of engineer-in-charge, with reinforced barbed tape(r.b.t.) / spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of m.s. angle, c.c. blocks shall be paid separately) providing and fixing water closet squatting pan (indian type w.c. pan) with 100 mm sand cast iron por s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to is: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests providing and fixing white vitreous china pedestal type water closet (european type w.c. pan) with seat. and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to is: 7231, with all fittings and fixtures complete, including cutting and. making good the walls and floors wherever required: w.c. pan with isi marked white solid plastic seat and lid providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and c.p. brass spreaders with brass unions and g.1 clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: one urinal basin with 5 litre white p.v.c. automatic flushing cistern providing and fixing wash basin with c.1. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: white vitreous china wash basin size 630x450 mm with a pair of 15 mm c.p. brass pillar taps. providing and fixing stainless steel a isi 304 (18/8) kitchen sink as per is:13983 with c.i. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: kitchen sink with drain board 510x1040 mm bowl depth 250 mm providing and fixing 8 mm dla c.p. / s.s. jet w flexible tube upto 1 metre long with s.s. triangu plate to eureopean type w.c. of quality and make approved by engineer - in charge. providing and fixing p.v.c. low level flushing ciste with manually controlled device (handle leve conforming to is: 7231, with all fittings and fixture complete. 10 litre capacity - white providing and fixing p.v.c. waste pipe for sink c wash basin including p.v.c. waste fittings complete. semi rigid pipe 32 mm dia providing and fixing mirror of superior glass (ou approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing: rectangular shape 453x357 mm providing and fixing ptmt waste coupling for wash basin and sink, of approved quality and colour. waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. internal work exposed on wall 15 mm nominal dia pipes 20 mm nominal dla pipes providing and fixing ball valve (brass) of approved quality, high or low pressure, with plastic floats complete: 15 mm nominal bore providing and fixing uplasticised pvc connection pipe with brass unions: 30 cm length 15 mm nominal bore providing and fixing g.i. union in existing g.i. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required: 15 mm nominal bore 20 mm nominal bore 1 providing and placing on terrace (at all floor level polyethylene water storage tank, is: 12701 marke with cover and suitable locking arrangement an making necessary holes for inlet, outlet and overflo pipes but without fittings and the base support fo tank. providing and fixing c.p. brass bib cock of approves quality conforming to is:8931 15 mm nominal bore providing and fixing c.p. brass long body bib cock c approved quality conforming to is standards an weighing not less than 690 gms. 15 mm nominal bore providing and fixing c.p. brass stop cock (concealed of standard design and of approved make conforming to is:8931. 15 mm nominal bore providing and fixing ptmt ball cock of approved quality, colour and make complete with epoxy coated aluminium rod with l.p./ h.p.h.d. plastic ball. 115 mm nominal bore, 105 mm long, weighing not less than 138 gms 1 providing and fixing ptmt extension nipple for water tank pipe, fittings of approved quality and colour. 15 mm nominal borc, weighing not less than 32 gms excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: all kinds of soil 2 pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia providing, laying and jointing glazed stoneware pipes class sp-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 2 150 mm diameter providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) all-round s.w. pipes including bed concrete as per standard design: 150 mm diameter s.w. pipe 2 providing and laying non-pressure np2 class (light duty) r.c.c. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement: 2 fine sand) including testing of joints etc. complete: 300 mm dia. r.c.c. plpe providing and fixing square-mouth s.w. gully class sp-1 complete with c.i. grating brick maso chamber with water tight c.i. cover with frame 300 x300 mm size (inside) the weight of cover to not less than 4.50 kg and frame to be not less th 2.70 kg as per standard design: 100x100 mm size p type with common burnt clay f.p.s. (non modular) bric of class designation 7.5 constructing brick masonry road gully chamb 50x45x60 cm with bricks in cement mortar 1:4 cement: 4 coarse sand) including 500x450 mm pre cast r.c.c. horizontal grating with frame complete a per standard design: with common burnt clay f.p.s. (non modular) brick of class designation 7.5 providing and fixing aluminium work for doors windows, ventilators and partitions with extrude built up standard tubular sections/ appropriate sections and other sections of approved make conforming to 15: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, l.e. at top, bottom and sides with required epdm rubber neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for, glazing/paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge. (glazing, paneling and dash fasteners to be paid for separately): for fixed portion anodised aluminium (anodised transparent or dyed to required shade according to is: 1868, minimum anodic coating of grade ac 15) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of epdm rubber / neoprene gasket required (fittings shall be paid for separately) anodised aluminium (anodised transparent or dyed to required shade according to is: 1868, minimum anodic coating of grade ac 15) providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to is: 12823 grade 1 type ii, in panelling fixed in aluminum doors, windows shutters and partition frames with c.p. brass stainless steel screws etc. complete as per architectural drawings and directions of engineer-in- charge. pre-laminated particle board with decorative lamination on both sides providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (cost of aluminium snap beading shall be paid in basic item): of work with float glass panes of 5 mm thickness (welght no less than 12.50 kg/sqm) providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to is 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece m.s. sheet outer box with silde plate etc. complete as per the direction of engineer-in charge. 5 5.1 16 with stainless steel cover plate minimum 1.25 mm thickness providing and fixing brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary screws etc. complete. anodized (ac 15) aluminium providing and fixing aluminium round shape handle of outer dia 100 mm with ss screws etc. complete as per direction of engineer-in-charge 16.1 anodized (ac 15) aluminium 0.3 96 providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of t-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. providing and fixing aluminium sliding door bolts, isi marked anodised (anodic coating not less than grade ac 10 as per is: 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete: 96.1 97 300x16 mm providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: 300x10 mm 97.1 100 providing and fixing aluminium handles, isi marked, anodised (anodic coating not less than grade ac 10 as per is: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete. : 00.1 125 mm 8.45 finishing walls with textured exterior paint of required shade: 45.1 new work (two or more coats applied 3.28 itr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm k carriage of material by mechanical transpor including loading, unloading and stacking: 20 km lea lime, moorum, building rubbish 20 km lead providing and fixing on wall face unplasticised rigi pvc rain water pipes conforming to is: 13592 typ a, including jointing with seal ring conforming to is 5382, leaving 10 mm gap for thermal expansion, (i single socketed pipes. 110 mm diameter providing and fixing on wall face unplasticised pvc moulded fittings/ accessories for unplasticised rigic pvc rain water pipes conforming to is: 13592 type a, including jointing with seal ring conformning to is 5382, leaving 10 mm gap for thermal expansion. bend 87.5° 110 mm providing and fixing unplasticised -pvc pipe clips of japproved design to unplasticised pvc rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with m.s. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement: 4 coarse sand) and making good the wall etc. complete. 110 mm