tender for annual plan-project no: 554/25-26- renovation of phc in div.57 of vyttila zonal - kochi municipal corporation-phc naveekaranam-general civil work - providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is : 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminnium snap beading for glazing /paneling, c.p. brass/ stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge.(glazing, paneling and dash fasteners to be paid for separately):for fixed portionpowder coated aluminium (minimum thickness of powder coating 50 micron) 3 21.2.2:providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to is : 12823 grade i type ii, in panelling fixed in aluminum doors, windows shutters and partition frames with c.p. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer - in- charge.pre- laminated particle board with decorative lamination on both sides 4 21.5:providing and fixing powder coated aluminium work ( minimum thickness of powder coating 50 micron) consisting of tee /angle sections, of approved make conforming to is : 733 in frames of false ceiling including aluminium angle cleats with necessary c.p brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to g.i level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the engineer-in-charge ( level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately ). 5 21.6:providing and fixing 6 mm dia. g i level adjusting hangers ( upto 1200 mm length), fixed to roof slabs by means of ceiling cleats made out of g.i flat 40x3 mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per direction of engineer -in-charge. 6 50.12.4.1:providing and fixing false ceiling with 7.5 mm thick pvc plain panel board ceiling of approved quality in aluminium frame work with necessary screws etc complete (aluminium frame work shall be paid separately) 7 15.23.1:dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.for thickness of tiles 10 mm to 25 mm 8 4.1.5:providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level:1:3:6 (1 cement : 3 coarse sand (zone-iii) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) 9 11.46.2:providing and laying vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to i.s. 15622, ofapproved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.size of tile 600x600 mm 10 50.6.3.2:solid block masonry using pre cast solid blocks (factory made) of size 40x20x10 cm or nearest available size confirming to is 2185 part i of 1979 for super structure up to floor two level for 10 cm thick wall in : cm 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete 11 13.1.2:12 mm cement plaster of mix:1:6 (1 cement : 6 fine sand). 12 13.43.1:applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:water thinnable cement primer 13 17.10.2.3:providing and fixing stainless steel a isi 304 (18/8) kitchen sink as per is 13983 with c.i. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:kitchen sink without drain board470x420 mm bowl depth 178 mm 14 18.15.2:providing and fixing brass bib cock of approved quality :20 mm nominal bore 15 13.83.2:wall painting with premium acrylic emulsion paint of interior grade, having voc (volatile including applying additional coats wherever required to achieve even shade and colour.two coats 16 od302194/2025-2026:providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by engineer-in-charge) 0.350 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by engineer-in-charge. the sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with epdm seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 17 od304363/2025-2026:providing and fixing rain water gutter semi circular section using 150mm dia 6kgf pvc pipe including fitting with 32x5mm flat supporting at 1m intervals complete as per the direction of engineer in charge at site. 18 od303123/2025-2026:od1259108/2021_2022 :engaging mancoolies od36 19 od304430/2025-2026:engaging plumber for rerouting the existing plumbing line etc as per direction of eic