provn of sewage line (100m) near office complex and living area at certain mil unit, special repair to bldg no p-11 (lrw) of certain mil unit and special repair to bldg no p-10 (c coy store) of certain mil unit at binnaguri under ge (s) binnaguri.; 1 dismantling asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings complete all as specified. 2 supply and fix 0.50mm thick prepainted galvalume polyester coated (smp coating) coloured metal roofing sheet trapezoidal profile having tensile strength 550mpa as in roof covering fixed with self drilling screws with epdm washer etc complete all as specified. 3 ditto--- all as per serial item no 2.00 described here-in-before but as in eaves board fixed with selp tapping screw as specified. 4 dismantling floor hearth or wall tilingincl cement mortar beddingand removing the rubbish off the premises complete all as specified 5 m&l for coloured non skid joint free ceramic tiles (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles and laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified 6 m&l for glazed colouredceramic tiles (350x450x7mm thick)on vertical surfaces such as skirting/dado set and jointed in neat cement slurry pointed in white or coloured cement to match with the shade of tile and fixed over and including 15mm thick rendering in cm(1:4) complete all as specified 7 demolition of cement concrete (un reinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified 8 m&l for machine cut kota stone slab flooring 20-25mm thick over cement screed base 15 mm thick in cm (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing completecomplete all as specified 9 m&l for 25 mm thick cement concrete type b1, 1:2:4 (using 20 mm graded stone aggregate) as in floor etc and finishing cement concrete for receiving floor finishes complete all as specified 10 m & l for kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed 10mm tick in cm (1:4)and jointed with ditto as per item9 above complete all as specified 11 m&l for cement concrete type c-2, 1:3:6 (using 40mm graded stone aggregate) 75mm thick as in plinth protection, footpath , under paver block etc and finished the surface even andsmoothcomplete all as specified 12 m & l for 80 mm thick m-30 grade factory made vibratory compacted cement concrete rubber moulded, interlocking paver block any shape and size confiroming to is 15658-2006 with grey cement and pigment as approved laid over and incl 50 mm thick consolidated sand cushion and joints filled with sand complete all as specified 13 m & l for pcc 1:2:4 type b-i ,(using 20 mm graded stoneaggregate) as. in coping /benching to sides of foot pathfininished fair and even including necessary use and waste of formwork etc complete all as specified 14 demolition of brickwork or stone/boulder masonry, built in cement mortar complete all as specified. 15 m&l for brickwork with burnt fly ash old size bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:6 complete all as specified 16 taking down of cement plaster of any description from brick wall surface etc including racking out joints and hacking for key, scrubbing down with water etc and removal of rubbinsh off the site complete all as specified 17 m&l for rendering 15 mm thick on fair faces of brick work or concrete surfaces of walls in cement morter 1:4 with water proofing compound finished even and fair complete all as specified (note : wpc shall be measured and paid separetely) 18 m&l for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement morter 1:6 finished even and smooth without using extra cement complete all as specified 19 m&l for rendering 5mm thick in cm (1:3) on fair faces of concrete surfaces as in celling finished fair and even without using extra cement complete all as specified 20 m&l for preparing of new plastered surfaces of wall and applying two coats of cement based wall care putty (agg thickness 1.5 mm) including preparation of surface to receive finishes (primer, distemper, paint etc.) complete all as specified 21 m&l for preparing new plasteredsurfaces of walls and finishing the walls with acrylic smooth exterior paint of required shade for new work two or more coats applied over and including priming one coat of exterior primer applied complete all as specified . 22 m&l for prepartion of newly plasteredsurfaces of walls and applying two coats of oil bound distemper over a coat of primer to wall surface complete all as specified 23 m&l for preparing newplastered surfaces of wall and applying three coat of white wash on ceiling surfacecomplete all as specified. 24 m&l for complete removal of existing treatment and finishing the walls with two coats of acrylic smooth exterior emulsion paint of required shade for new work over and including priming one coat of exterior primer applied all as per manufacturers specification and as specified. 25 m&l forapplying two coat of acrylic -based distemper of shade over a coat of primer over 1.00mm thick finished putty surface of old wall complete all as per manufactures specified as as speciffied 26 m&l for preparing old decorated/undecorated ceiling surfaces of wall and applying two coat of white wash complete all as specified. 27 supply only liquid water proofing compound (wpc) of best quality complete all as specified 28 s&f in repairs factory made z sectionsteel windowwith side hung shutter frame includingprojecting/ boxtype hinge with steel handle and steel peg stay, ms tower bolt etc. completewith glazing bars , dovetailed or welded including a shop coat red oxide priming complete all as specified 29 s&f in repairs factory made z section steel ventilator with top hung shutter incl hinges, steel peg stay,with glazing bars including a shop coat red oxide priming complete all as specified 30 supply and fix 4mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50sqm in each pane complete all as specified 31 m&l for applying two coat of synthetic enamel paint over a coat of red oxide primer after preparation of new steel surfaces over exc 10cm in width or girthcomplete all as specified 32 m&l for preparing old painted steel surface of any description not otherwise described for over 10 cm width or girth and applying one coat of synthetic ennamel paint complete all as specified 33 taking down chowkat or frame with door shutter (without taking off shutter from the frame) exc. 1.5 sqm and n.exc 4 sqm each, making good disturbed surfaces and removing materials from site of work complete all as specified 34 m&l for pressed steel door frame of size 105mm x 60mm with one or more rebates including necessaryfixing lugs , hinges, lock strike plate etc complete all as specified 35 s&f 30mm thick factory made flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides kiln seasoned and chemically pressure treated complete all as specified 36 s&f aluminium anodizedbarrel tower bolts, extruded section 200mm long complete all as specified. 37 s&f aluminium anodized handles, d type, 150mm size complete all as specified 38 s&f 300mm long aluminium alloy, anodiseal sliding bolt with hasp, staple (bolt type) and fixing clim of steel, cast or extruded section and fixing bolts and sliding bolts of extruded section or cost aluminimum alloy and fixed 39 m&l for cement concrete type b1 1:2:4 (20mm graded aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified. 40 supply & fixing in repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless and as required framing steel staples complete all as specified 41 m&l for preparation of new surface & applying two coats of synthetic enamel paint over a coat of pink primer to wooden surfaces exc 10 cm in width or girth complete all as specified 42 m&l preparing old painted wooden surface of any description not otherwise describedover 10 cm in width or girth and applying one coat of synthetic ennamel paint complete all as specified 43 excavation in trenches, n exc 1.5 mtr wide and n exc 1.5 mtr in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. n exc 10 sqm on plan and n exc 1.5 mtr in depth and getting out in soft/loose soil complete all as specified 44 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick in soft/loose soil complete all as specified 45 removing of surplus soil/excavated materials to a distance not exc 50 m away from the starting point and depositing where directed at a level not exc 1.5m above the ground level complete all as specified 46 m&l for pcc (1:4:8)type d2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified 47 m&l for precast rcc (1:2:4) type b1 using 20mm graded stone aggregate as in cover slabs of drains set in cm (1:6) including necessary use and waste of form work complete all as specified 48 m&l for mild steel tmt bars, 10 mm dia and over cut to length, bent to shape as required including cranking, bending and binding with and including mild steel wire (annealed)not less than 0.90 mm dia complete all as specified 49 s&f sgsw drain pipe of size internal 200 mm dia (grade a) laid in trenches and jointed in cement mortar (1:1) complete all as specified 50 m&l for concretebed in cement concrete 1:3:6 type c2 (using 40mm graded stone agg)to drain pipes of 200 mm boreincludingpacking under and hunching against the sides of pipes after they are laid and tested complete all as specified 51 cutting into existing man holes for connecting new drain of 200mm dia pipe and making good to pipes and rendering, cutting out existing benching for and forming branch channel(1/2 round or 3/4 section) in cement concrete 1:2:4 type b1 and finished and reforming benching as required complete all as specified 52 s&f in repairs 1.25mm thick steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod,hasp and staple and one shop coat of primer,erected in position as indicated, complete: push pull or manual type complete all as specified 53 -----blank----- 54 m&l for pcc (1:3:6) type c2 (using 20mm graded stone aggregate) as in surface channels/drain complete all as specified 55 extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends ect complete all as specified 56 supply and fix industrial socket tp and earth enclosure of 32 amps capacity 415 volts with socket and top with mcb 32 amps tp c curve, 10ka including taking down old unserviceable one complete all as specified. 57 s&f sheet metal enclosure for 8 way distribution boards (db’s), double door, single pole & neutral with din rail, ip-43 protection suitable for fixing mcbs/lsolators completeincluding provision of blanking plates as required and taking down the old one complete all as specified. 58 s&f mcb, triple pole neutral 100 amps, 415 volts, ‘c’ curve, 10 kaall completeincluding taking down the old one complete all as specified 59 supply and fix exhaust fan, steel body ac single phase 230v of size 300mm sweep with, blades,frame and louvers shutter voltage 230v, 50 hz, rpm 1200, copper winding of sweep 300mm and provision of 3 core flexible multistranded copper conductorof size 0.75 sqmm from ceiling rose to fan incl 20/25mm pvc electical flexible pipe including making hole to wall of suitable dia for housing exhaust fan complete all as specified. 60 taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified 61 m&l for point wiring complete with 1.5 sqmm multistranded copper conductor single core pvc insulated, is 694 unsheathed fr-ls cable 1100 volts grade (isi marked) with proper colour coding drawn through and including non-metallic rigid pvc medium grade conduit not less than 20mm dia and conduit accessories (isi marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 sqmm pvc insulated multistranded unsheathed copper conductor cable fr-ls (isi marked) as earth continuity conductor connected to common earth dolly, fabricated sunken terminal box made out of gi sheet steel not less than 1.22 mm thick for boxes duly painted with anticorrosive paint, concealed in walls with bakelite/plastic laminated sheet top cover fixed with cadmium plated iron screwsfor housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sunken for boxes and making good to the disturbed surface of wall/floor and matching with existing specificationsall as specified and where concealing of conduit is not feasible i.e on surface of roof /ceiling etc, conduit shall be fixed on surface with necessary saddles at no extra cost for the following :- 62 one light point controlled by one, lone way switch 5/6 amps complete all as specified. 63 one ceiling fan/exhaut fan point controlled by one, lone way switch 5/6 amps complete all as specified. 64 one socket out let 5/6 amps point on the same board complete all as specified 65 one socket out let 5/6 amps point on the independent board complete all as specified 66 ditto as per serial item no 61 described here-in-before but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified. 67 s&f switch piano flush type 5/6 amps single pole one way complete all as specified. 68 s&f socket 3 pin, 5/6 amps, white ivory finish flash type complete all as specified. 69 s&f of socket outlet 2 in 1, 5 pin, 5/15 amp,multipurpose 230 volt flash type complete all as specified by engr-in-charge. 70 s&f switch piano flush type 15/16 amps single pole one way complete all as specified. 71 s&fceiling rose, surface type with back plate, three terminal /pvc/ polycarbonate, isolated body complete all as specified. 72 s & f deluxe fan electronic regulator 230 volts ac 50 hzs rotary step white/ivory finish complete all as specified. 73 s&f led lights fitting 1x 20w, 220v ac decorative box type with driver,ip 20, class i, wall/ surface mounted, integrated type with extruded aluminium housing integrated high efficiency electronic driver and surge suppressor of 4kv or more, luminaire efficiency not less than 120 lumens/watt, power factor not less than 0.90, cri 80, thd 10%, operating range - 140 to 270 v, 50 hz fixed with 02 nos of pvc round/ square blocks, screws etc connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.complete with all accessories internally prewired and connecting up with complete all as specified. 74 s&f led bulk head lights fitting 1x 9/10w, 220v ac integrated high efficiency electronic driver and surge suppressor of 4kv or more, luminaire efficiency not less than 120 lumens/watt, power factor not less than 0.90, cri 80, thd 10%, operating range - 140 to 270 v, 50 hz fixed etc connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.complete with all accessories internally prewired and connecting up with complete all as specified. 75 s&f sheet metal enclosure for 4 way distribution boards (db’s), double door, single pole & neutral with din rail, minimum ip-43 protection suitable for fixing mcbs/lsolators completeincluding provision of blanking plates as required and taking down the old one complete all as specified 76 s&f mcb, single pole & neutral 6 to32 amps, 240 volts, ‘c’ curve, 10 kaall completeincluding taking down the old one complete all as specified 77 s&f mcb, single pole, 6 to32 amps, 240 volts, ‘b’ curve, 10 kaall completeincluding taking down the old one complete all as specified 78 m &l for earthing complete with gi earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal gl. connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washersincluding necessary excavation and earth work in soft/loose soil, gi protection pipe light grade 15mm bore for protecting the gi wire mesh funnel alternate layer of charcoal dust, and saltpcc pit 1:3:6 type c1 using 20mm graded stone aggregate and 50mm thick rcc 1:2:4 type bo using 20mm graded stone aggregate cover re-inforced with 8 mm dia ms tmt bars 80mm c/c both ways complete all as specified and shown in electrical plate no.3 ssr part-1 and connected to the earth point and testing complete including taking out the old one complete all as specified 79 m & l sub main wiringconcealed type with two run single core cable pvc insulated cable with4.0sqmm (nominal area) multi stranded copper conductor frls cable 1100 volts gde incl earth continuity conductor using pvc insulatedcable of stranded copper conductor of size 4.0 sqmm connected to common earth dolly anddrawing into rigidpvc conduitsof 25 mm dia medium gradesize,making good the disturbed surfacescomplete including necessary taking down.(note : two run of submain wiring cable alongwith one run of earth wire and concluding shall be measured as one length. 80 taking down ceiling fan sealing cable end, dismantling blades and removing fan and blades to store complete all as specified. 81 m&l for painting of ceiling fans of any make/model and size complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc.complete all as specified. 82 m&l for hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified. 83 supply, laying, jointing & testing in trenches or passing through pipe, 1100 volts grade, xlpe insulatedpvc bedded, galvanized steel strip or wire armoured lt electric power ug cables, heavy duty with stranded aluminium conductor of cross sectional area 16 sqmm 2 core with and including all fixing & connecting accessories such as aluminium cable lugs, cable gland, nut, bolts, washer etc complete including taking out old unsv cable complete all as specified.(note: earthwork & excavation, gi pipe, bricks for protection etc shall be measured and paid separately under relevant items of this schedule a). 84 supply, laying, jointing & testing in trenches or passing through pipe, 1100 volts grade, xlpe insulatedpvc bedded, galvanized steel strip or wire armoured lt electric power ug cables, heavy duty with stranded aluminium conductor of cross sectional area 50 sqmm 4 core with and including all fixing & connecting accessories such as aluminium cable lugs, cable gland, nut, bolts, washer etc complete including taking out old unsv cable complete all as specified.(note: earthwork & excavation, gi pipe, bricks for protection etc shall be measured and paid separately under relevant items of this schedule a). 85 supply and lay dry river sand filling for under ground cable protection with a layer of 8cm thick before laying and 15cm thick covering above the top edge of cable after laying complete all as specified.note : punned down thickness upto 18cm shall only be measured and paid 86 supply and laying sub class b bricks of size 25cmx12.5cmx7.5cm (+/-10% tolerance) for protection of ug cable with width equal to length of bricks as mechanical protection laid dry and flat complete all as specified. 87 m & l for horizontal boring across the existing road without disturbing the road surface for insertinggi pipe complete all as specified note :- (i) removal of surplus soil shall be deemed to be include in the unit rate. (ii) gi pipe will be measured and paid separately under relevant item of sch a. 88 m&l for 40 mm bore steel tubing light grade isi marked for protection of cable including necessary joints complete all as specifiedmake: tata/jindal/bansal 89 m&l sub main wiring concealed type with four run single core cable pvc insulated cable with 4.0 sqmm (nominal area) multi stranded copper conductor frls cable 100 volt gde incl earth continuity conductor using pvc insulated cable of stranded copper conductor of size 4.0 sqmm connected to common earth dolly and drawing into rigid pvc conduits of 25 mm dia medium grade size making good the disturbed surfaces complete including necessary taking down. note : four run of submain wiring cable alongwith one run of earth wire and concluding shall be measured as one length