tender for addn/altn of otm accommodation at along mil station under ge 872 ews.; 1 dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof/ wall covering all as specified and directed 2 m&l dismantling structural steel work in any description complete all as specified and directed. 3 s&f rolled mild steel sections (fe-290 gde e- 165) joist, channel, angle, or tee sections as in cross beams, hip and jack rafters, purlins where connected to common rafters(cut to ordinary lengths i.e. within 20mm of the length indicated)complete all as specified and directed. 4 s&f steel work in tubular trusses including special shaped washer etc. complete using erw or induction butt welded tubes conforming to i. s.1161- 1979 grade st.-240 complete all as specified and directed. 5 s&f pre- painted galvalume aluminum zinc coating gi based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. 6 s&f pre-painted galvalume aluminium zinc coating gi based plain steel sheet 0.50mm of an colour having tensile strength of 550mpa as in roof covering/ridges/cladding to wall, fixed with self tapping screws complete all as specified and directed. 7 s&f 0.63mm galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 complete all as specified and directed. 8 m&l preparation of new or previously untreated steel surfaces exc 10 cm width or girthand applying two coat of synthetic enameled paint over one coatof red oxide primer completeall as specified and directed. 9 demolition of wall and ceiling boards (fibre,pulp,insulation etc) or insulation boards/ slabs/ blankets, any thickness, inculding cover fillets complete all as specified and directed. 10 dismantling of timber scantling 40 sqcm and over in section in any position for unframed workscomplete all as specified and directed. 11 s&f second class clean swan hardwood scantling complete all as specified and directed. 12 m & l preparing surface of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint complete all as specified and directed. 13 s&f 6mm thick plywood, grade,bwr, type bb, fixed with screws to timber frame work as in wall claddingcomplete all as specified and directed. 14 s & f 2nd class hard wood plain fillets square, rectangular or triangular in section, wrought secured with nails, cross sectional area exceeding 3 sq. cm but nexc 6 sqcm complete all as specified and directed. 15 s & f anodised aluminium snap grid frame work size 605mm x 605mm for false ceiling hangers with 6mm dia gi (upto 1200mm length) adjusting level fixed to roof and fixing of 6mm thick non asbestos fibre cement building boards fixed or laid/ inserted to timber/gi/aluminium framework complete all as specified and directed 16 taking down chowkhats or frames not exc 1.5 sqm each with shutters completeall as specified and directed. 17 taking down chowkhats or frames with shutters exc 1.5 sqm but not exc 4 sqm completeall as specified and directed. 18 s&f harrison rails, mild steel chromium plated with fixing brackets, stops, rollers etc. complete all as specified and as directed including taking out old one complete all as specified and as directed. 19 m&l rolled sections as in iron chowkats, framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc (grade fe 290 e 165) complete all as specified and as directed. 20 s&f iind class hard wood plain, solid, straight, chowkats and frame, wrought, frammed or rebated on the solid rounded or chamferred, put together with glue pinned at joints complete all as specified and as directed.. 21 m&l 30 mm thick 2nd class hardwood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied and fitted to chowkats complete all as specified and directed. 22 s&f 30mm thick, 2nd class hard wood in glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in ssr part i, section 8, clause 8.24 (a); supplied and fitted to chowkats completeall as specified and directed. 23 s&f powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified 24 s&f powder coated (thickness of powder coating not less than 50 micron) anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed. 25 s&f powder coated (thickness of powder coating not less than 50 micron) anodised aluminium window and ventilator shutters, as in multi traktype without sash bars, aluminium sectionsweighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminiumsnap beading, screws, anodised aluminium fittings such as locking arrangements complete all as specified and as directed. 26 s&f 12mm thick toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required complete all as specified and as directed. 27 s&f of 5.50mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as directed. 28 s&f double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and as directed. 29 s&f 150mm extruded brass handles, fabricated type polished complete all as specified and as directed. 30 s&f brass mortice lock,4 levers, vertical type, size 100 mm fixed with aluminium frame complete all as specified and as directed. 31 s&f 10mm thick toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required complete all as specified and as directed.. 32 s&f of aluminium (extruded section body) door closer hydrauically regulated, designation no. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and as directed. 33 s&f of 4.00mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as directed. 34 s&f providing and fixing factory made upvc white colour fixed window area exc 2.00 sqm made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). window profile with hollow section with multi chamber. frame (60mm x 58mm). t profile (onevertical length in between two shutters) (60mm x 74mm). glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, epdm gasket 1.2 +–0.2mm thick, galvanized steel frame (28mm x 21.5mm), t profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass complete all as specified and as directed. 35 s&f providing and fixing factory made upvc white colour casement (openable) door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). t profile (one vertical length in between two shutters) (60mm x 74mm). glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. epdm gasket 1.2 + -0.2mm thick galvanized steel frame (28mm x 21.5mm), sash (31mm x 27mm), t profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. hardware: [casement door handle made of zinc alloyed (white powder coated). corner striker. secondary strikers. cylinder. door transmission gear made of mild sleel with multi point locking system with strikes. 3d hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality glass complete all as specified and as directed. 36 s & f mild steel windows with side hung shutters including box type hinge with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed. 37 s & f mild steel windows with side hung shutters including projecting type hinge with steel handle and steel peg stay, complete with out glazing bars, dovetailed or welded complete all as specified and directed. 38 s&f factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of ms tube for top and bottom rail.ms frame shall be covered with heat moulded plain colour pvc ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour pvc sheet to be fitted in the ms frame welded/sealed to the stiles and rails with suitable pvc sheet beading and joined together with solvent cement complete all asspecified and directed 39 s&f solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with ms square tube, incl fixing arrangement, suppling & fixingin opening as per specification completeall as specified and directed. 40 m & l for preparing old previously treated surface of wood and wood based surfaces of any description not other wise described over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 41 s&f aluminium anodized 150mm long barrel tower bolt of extruded section completeall as specified and directed. 42 s & f aluminium handles size 150mm cast type anodised completeall as specified and directed. 43 s&f mild steel sliding door bolt, 300 mm plate type, stove enamelled black, with bright bolt not less than 12 mm dia with and incl a min of 6 bolts and nuts, four on bolt plate and two on staple plate completeall as specified and directed. 44 s&f 10mm butt hinges medium weight cold rolld mild steel completeall as specified and directed. 45 m&f for framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to fe.290.gde-e-165 complete all as specified and as directed. 46 m&l for mild steel work as in holdfasts ,knee piece and similar small article confiraming to fe-290 gde-e-165 complete all as specified and as directed. 47 m&l plain cement concrete 1:3:6 type c-1 (using 20mm graded stone aggregate) as in bed blocks for fixing hold fasts etc. complete all as specified and directed. 48 s&f galvanised ms wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tack or galvanised wire staples completeall as specified and directed. 49 s&f 3mm thick sheet glass, ordinary quality andglazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and as directed. 50 s&f 300 mm long ordinary rat tail rod pattern door springs including roller and roller plate complete and fixed to chowkats with welding or screws as per requirement completeall as specified and directed. 51 m&l preparation of new surface of wood and wood based surfaces of any description not otherwise described over 10 cms width or girth and applying 2 coats of synthetic enamel paint over a coat of pinkprimer all as specified and directed. 52 demolition of brick work or stone masonry built in cement mortar including all quoins, pillars, arches etc. complete all as specified and as directed. 53 m&l precast cement concrete 1:3:6 type c-1 (using 20mm graded aggregate) block masonry with solid blocks exc10 cm thick in width and setting in cement mortar 1:6 as in wall complete all as specified and as directed. 54 taking down cement or cement lime plaster of any discription on bricks or stone walls/ceiling etc including racking out joints, hacking for key, scrubbing down with water completeall as specified and directed. 55 m&l 10 mm thick plastering in cm 1:6 on brick/ concrete surfaces including finishing the surfaces fair and even complete all as specified and directed. 56 m&l rendering 15mm thick in cm 1:4 onany faces of brick work or concrete surfacesincluding finishing the surfaces fair and even by using wpc as per manufacturers instructions complete all as specified and directed. note:- wpc will be measured & paid separately in respective item. 57 supply only water proofing compound complete all as specified and as directed. 58 s&f solid pvc wall lining consisting of5mm thick wooden grain pvc sheet inclusive of solvent cement and fixing atsite on pvc frame as per specifications and drawing complete all as specified and as directed. 59 s&f 5mm thick pvc sheet fillet of width35mm for wall paneling inclusive offixing on to wall to make pvc frame asper specification and drawing complete all as specified and as directed.. 60 m&l for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat primer and over a coat of 1mm thick (average) birla putty complete all as specified and directed. 61 m&l for complete removal of existing treatment old plastered or unplastered surfaces including preparation surfaces ofwalls and applying two coat of distemper oil emulsion on wall over a coat of primer and over a coat of 1mm thick (average) wall care putty all as specified and directed. 62 m&l for preparation of new plasteredsurface of wall and applying three coat of white wash complete all as specified and as directed 63 m&l for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed. 64 m & l rendering 5mm thick on ceiling surfaces on brick wall or concrete surface in cement mortar 1:3 finishedeven and smooth without using extra cement complete all as specified and as directed. 65 m&l for preparation of newlypalstered surfaces and applying three coats of white wash on ceiling all as specified and as directed. 66 demolition of cement concrete (unreinfoced) in ground floor,paving nexc 15mm thick(below or above gl) complete all as specified and directed 67 m&l for 25mm thick pcc 1:2:4 type b-0 (using 12.5 mm graded crushed stone aggregate) as in floors/paving/ path etc. complete all as specified and as directed. 68 m&l for 75mm thick plain cement concrete (1:3:6) type c-2 using 40mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement complete all as specified and directed. 69 dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed. 70 m&l for light shade vitrified ceramic tiles 10mm thick (square/rectangular) area of each tileexceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm screed in cm 1:4 complete all as specified and directed 71 m&l for light shade coloured vitrified ceramic tiles 10mm thick (square/ rectangular) area of each tile notexceeding 0.36 sqm, in floors, skirtings etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm screed in cm 1:4 complete all as specified and directed 72 m&l non-skid ceremic tiles coloured 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but n exc 0.18 sqm, in floors, skirtings etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles including for screed bed (or) bedding layer of cement morter 15 mm thick, in cement mortar 1:6 for laying floor finishes complete all as specified and directed. 73 m&l for coloured glazed tiles of size 450x 350x 7mm thick fixed with neat cement slurry in vertical surface to wall pointing in white/coloured cement to match over and including 10mm thick rendering in cm (1:4) complete all as specified and directed. 74 m&l for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, polishing and including 15mm screed bed in cm 1:6 complete all as specified and directed. 75 m&l for machine cutkota stone slab flooring 20-25mm thick over cement screedbase laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including 15mm screed bed in cm 1:6, rubbing and polishing complete all as specified and directed. 76 s&f in repairs bib taps chromium plated (fancy type) cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule suitable for 15mm bore pipe complete. 77 s&f in repairs vitreous china wash basin pedestal pattern size 600x480mm white including 32mm dia waste coupline 32mm dia ofbore waste coupling of ptmt(half or full threaded) .(minimum weight 32mm 45gms/40mm-60 gms) complete all as specified and as directed. 78 s&f sinks made of stainless steel 1mmthickkitchenor laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm and bowl size 410mm x 330mm x 160mm complete all as specified and as directed. 79 s&f in repair pillar tap 15mm bore (dia), cast copper alloy with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and as directed. 80 s&f in repair central hole wash basin mixer with 450mm long flexible hose complete all as specified and directed. 81 s&f in repair vitreous china squatting pan orrisa pattern 580x440mm size pan white with front or back inlet with integral foot rest, incl pvc (swr) p or s trap 110mm dia & provn of lime/cement concrete bedding and pvc flush pipe complete all as specified and as directed. 82 s&f in repairs10 ltr pvc valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including flush pipe of polyetylene of low or high density or pvc. 32mm dia, for low level cisterns brackets etc complete all as specified and as directed. 83 s&f in repair vitreous china white urinal, half stall type (excluding flushing cistern, flush pipe and waste pipe) including providing and fixing plugs, bedding urinals against wall in cement mortar 1:2, securing urinal to plug with and including 60mm long brass chromium plated screws, pointing around urinal back in cement mortar 1:3, fixing urinal spreader of ptmt, flush pipe, 50mm bore low density polyethylene (ldpe) pipes of pressure rating 6 kgf/sq. cm grating and union for discharge pipe complete all as specified and as directed. 84 s & f in repairs vitreous china water closet pan (pedestal pattern), white including fixing bolts, plastic water closet seat, black/white closed pattern with flat bottom and cover and mild steel chromium plated hinging device complete all as directed. 85 s & f in repairs vitreous china water closet one piece (incl flushing cistern) white including fixing bolts, plastic water closet seat cover, and mild steel chromium plated hinging device complete all as directed. 86 s & f in repair of brass cp wall mixer for shower including , mixing of hot & cold water screwed down for iron pipe of 15mm dia. complete all as specified and as directed. 87 m &l for preparing old previously treated steel surface of any description not other wise described over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 88 s & f steel tubing of 15mm bore medium grade including fittings fixed to wall/ celing laid in floors etc complete and making good the area to match with existing surface including taking down old steel tubing & connection complete all as specified. 89 m&l cutting chases, pinning in, (pcc blockwall) making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth 90 s & f steel tubing of 20mm bore medium grade including fittings fixed to wall/ celing laid in floors etc complete and making good the area to match with existing surfaceincluding taking down old steel tubing & connection complete all as specified. 91 s & f in repairsrotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position of 1000 litres capacity confiring to is specification complete all as specified and as directed.. 92 supply & fix in repairs ball valves high pressureof ptmt with epoxy coated aluminium rod & high density plastic ball screwedfor iron pipe or brass ferrule20mm bore weight not less than 210 gm. complete all as specified and as directed. 93 taking down/up unserviceable soil, waste and ventilating pipes 75mm/110mm bore (dia) with pipes fittings of any descriptions, fixing on walls or laid in floors, etc., complete all as specified and as directed. 94 s&f 110mm pvc (swr) pipes(isi marked) single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed. 95 s&f 75mm pvc (swr) pipes(isi marked) single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed. 96 s&f in repair high density polyethylene pipes (hdpe) 50mm dia of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc incl fittings required complete all as specified and as directed 97 s&f pvc (swr) bends (any radius), diminishing pieces or tapers (larger bore measured) fittings for pvc (swr) pipe 110mm bore (dia), jointing with solvent cement, complete all as specified and as directed. 98 s&f pvc (swr) bends (any radius), diminishing pieces or tapers (larger bore measured) fittings for pvc (swr) pipe 75mm bore (dia), jointing with solvent cement, complete all as specified and as directed. 99 s&f pvc (swr) 110mm bore (dia) junction, single (single t) equal or unequal with access door, etc., jointing with solvent cement, complete all as specified and as directed. 100 s&f pvc (swr) 75mm bore (dia) junction, single (single t) equal or unequal with access door, etc., jointing with solvent cement, complete all as specified and as directed. 101 s & f in repairs pvc connections 15mm size with ptmt nuts of length 450mm complete all as specified and as directed.. 102 s & f in repairs 15mm dia stop/angle valves, cast copper alloy , screwed down, high pressure with crutchor butterfly handle screwed both ends for iron pipes all as directed by engr-in-charge. 103 m&l for pvc (swr) floor trap withgrating including jointing to waste pipe fixed with solvent cement.diameter of outlet in 75 mm) complete all as specified. 104 s & f in repair ptmt grating doom 100mm dia (minimum weight 25gms) complete all as specified and as directed. 105 s & f in repairs tubular towel rail brass chromium plated, 20mm dia, d type 60 cm long between flanges complete all as specified and as directed. 106 s & f in repairs brass chromium plated shower rose 125mm size swivel type complete all as specified and as directed.. 107 s&f in repair hand shower (health faucet) with inner flexible tube not less than 1.20 metre in length and wall hook, complete all as specified and as directed. 108 s & f in repairs 600x450 mm bevelled edge mirror of selected quality glass mountedon pvc sheet / commercial ply / ac boardwith pvc moulded all around beading and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed. 109 m &l for preparation of plastered or unplastered old decorated surfaces of walls and applying one coat of cement base paint on walls complete all as specified and directed. 110 m &l for preparation of plastered or unplastered old decorated surfaces of walls applying one coat of white wash on walls complete all as specified and directed. 111 m &l for preparation of (previously treated) plastered or unplastered surfaces of walls and applying one coat of oil emulsion distemper any tint of walls complete all as specified and directed. 112 m&l for pcc 100mm thick type b2, 1:2:4 using (40mm graded aggregate)as in paths/hardstanding even and broom finish without using extra cementetc complete all as directed. 113 demolition/dismantling of stone slabs/paver blocks and tiles of any description or thickness laid bedded and pointed in any mortar in floors, approns etc. and clean the surface to receive screed bed to lay new tiles complete all as specified and directed. 114 m&l chequerred tiles 20cm x 20cm x 25mm thick with grey pigment cemented and pigments set and jointedand pointed in neat cement slurry in floors by using grey cement and pigments over& including 15mm thick screed bed in cm 1:4 complete all as specified and directed. 115 removing building materials aggregates, pcc etc to a distance of 100m or under, beyond then lead included in the rates, including loading, unloading and stacking at the destination 116 s & f in repair galvanized mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with wooden beads complete all as specified and directed 117 excavation in trenches not exc 1.5 m wide & n.exc 1.5 m in depth for foundation etcn.exc 10 sqm on plan & n.exc 1.5 m in depth & getting out in soft/loose soil complete all as specified and directed. 118 demolition & breaking up drain/ seware pipe 100mm/110mm dia pipes (salt glazed ware, ac or reinforced concrete) including pcc haunching (except bed), set in cement mortar, complete all as specified and as directed. 119 m & l for pcc 1:3:6 type c2 (using 40mm graded stone aggregate) for concrete bed to drain pipe including packing under and haunching against the sides of pipes laid and tested for 100/110mm outer dia pipes, complete all as specified and as directed. 120 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.in loose soil all as specified & directed 121 removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed. 122 s&f hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to fe-290 gde e-165 all as specified & directed 123 taking down existing unserviceable point wiring of any description/type/ size of light/fan/tube/power/two way/bell etc on tw batten/conduit includingremovalof batten / conduit / gutties / wooden boards / switches / sockets / regulators/ light fittings etc and removal of unserviceable material out of site and making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes all as specified. 124 taking down the existing unserviceable main switch / cut out / dbs of any type / capacity / description as existing at site including making good the disturbed surfaces to match with the existing finishes all as specified. 125 taking out old unserviceable/burnt submain wiring of any size and making good the disturbed surfaces complete all as specified and directed. 126 m&l for point wiring with 1.5 sq mm copper conductor single core flame retardant pvc insulated unsheathed 1100 volts multistranded drawn through and including rigid pvc caping and casing surfacetype andaccessories of suitable size isi marked and pressed steel terminal boxes of 2 mm thick ms of suitable size duly painted with red oxide metal primer including fixing/grouting sunken/ surface as per site requirement incl provision of 3 mm thick laminated hylem sheet for mounting the switches/sockets/regulators/ceiling rose etc including running up of 1.5 sq mm copper conductor flame retardant pvc insulated cable as earth continuity conductor along with wiring and connecting to the common earth dolly all as specified for one light point controlled by one, one way switch, 5 amps with cable 1.5 sqmm size. 127 all as per item no 126 above but one ceiling fan point controlled by one, one way switch, 5 amps with cable 1.5 sqmm size. 128 all as per item no 126 above butone exhaust fan point controlled by one, one way switch, 5 amps with cable 1.5 sqmm size. 129 all as per item no 126 above butone bell/ buzzer point controlled by one push button on the same board with other switches or independent with cable 1.5 sqmm size. 130 all as per item no 126 above but one 3 pin socket outlet, 5 amps, same board, with cables 1.5 sq. mm size. 131 all as per item no 126 above but one 3 pin socket outlet, 5 amps, independent, with cables 1.5 sq. mm size. 132 all as per item no 126 above butbutusing 2.5 sq mm single core copper conductor cable of multistranded flame retardant pvc insulated unsheathed 1100 volts grade for 5/15 amps switch socket, independent incl running of1.5 sq mm copper conductor flame retardant pvc wire as earth continuity conductor along with wiring and connecting to the common eath dolly. 133 all as per item no 126 above butbutusing 4 sq mm single core copper conductor cable of multistranded flame retardant pvc insulated unsheathed 1100 volts grade for 5/15 amps switch socket, independent incl running of1.5 sq mm copper conductor flame retardant pvc wire as earth continuity conductor along with wiring and connecting to the common eath dolly. 134 s&f switch piano, flush type,single pole one way 5 amp complete all as specified and directed. 135 s&f modular switch 1 way 6 a, 1 module complete all as specified and directed. 136 s&f switch piano, flush type,single pole one way 16 amp complete all as specified and directed. 137 s&f modular switch 1 way 16 a, 1 module complete all as specified and directed. 138 s&f bell push, flush type, 5 amp complete all as specified and directed. 139 s&f modular bell push 6 amp, 1 module. 140 s&f buzzer, ding dong ac. 230 volts, single pole complete all as specified and directed. 141 s&f ceiling rose, pvc/polycarbonate, isolated body 3 terminal complete all as specified and directed. 142 s&f socket outlet 2 in 1, 3 pin, 5 amps flush type universal complete all as specified and directed. 143 s&f modular socket, 6a - 2/3 pin combined 2 module complete all as specified and directed. 144 s&f socket outlet 2 in 1, 3 pin, 6 and 16 amp flush type universal complete all as specified and directed. 145 s&f modular socket 6a/16a - 2/3 pin combined 2 module complete all as specified and directed. 146 s&f stepped type electronic fan regulator flush type complete all as specified and directed. 147 s&f modular fan step regulator, 120w - 2 module complete all as specified and directed. 148 s&f modular white colour plate with frame 1 module complete all as specified and directed. 149 s&f modular white colour plate with frame 3 module complete all as specified and directed. 150 s&f modular white colour plate with frame 4 module complete all as specified and directed. 151 s&f modular white colour plate with frame 8 module complete all as specified and directed. 152 s&f modular white colour plate with frame 10 module complete all as specified and directed. 153 s&f modular metal flush box 1/2 module complete all as specified and directed. 154 s&f modular metal flush box 3 module complete all as specified and directed. 155 s&f modular metal flush box 4 module complete all as specified and directed. 156 s&f modular metal flush box 8 module complete all as specified and directed. 157 s&f modular metal flush box 10 module complete all as specified and directed. 158 s&f lamp holder, pvc polycarbonate type with back plate suitable for batten/angular fittings complete all as specified and directed. 159 s&f led tube light fitting 1 x 20 watt, 220 volts, ac decorative box type with driver, holder incl led tube light connecting up with 3 core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. 160 supply and fixing led luminaire 600 mm x 600 mm, 40 watt, 220 v ac recessed type with high efficiency pmma diffuser soft glare free light complete with driver, holders & led lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. 161 supply and fixing led luminaire, 18 watt, 220 v ac, round recessed type down light with die-cast aluminium housing finished in premium white powder coating, efficiency 100 lm/w & 120 lm suitable for roof ceiling complete all as specified and directed. 162 s&f led light fitting 1x9/10 watt bulkhead luminaires including led light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. 163 s & f bldg security light fittings high-quality group control enabled integrated led building security light with a minimum system lumen of 3000 lm and system wattage not exceeding 25w with a nominal system efficacy of 110 lumen/watt. the led used shall have cct of 5700k, sdcm ≤ 5 and cri≥70. the housing should be made of lm6/adc12 alloy, non-corrosive single piece pressure die-cast aluminum, to withstand extreme environments. the spigot shall be part of “single piece pressure die-cast housing” & shall not be bolted to the luminaire housing to ensure robust design. the name of the brand should be embossed/engraved & should not be mentioned using sticker/screen printing. it should have corrosion resistant powder coating to pass nss of 500 hrs. the luminaire led shall have declared lifetime of 75k hours@l70. the product should be designed for continuous operation (10-12 hrs. per day). the ingress protection should be minimum ip66 & impact resistance shall be ik10.control gear compartments shall be top maintainable without accessing/opening the optical compartment. the luminaire should have a minimum 20 kv/10ka spd duly bolted in the luminaire. the spd should be able to sustain a minimum 15 hits of 10ka rating i.e. total of 45 hits across all the three modes as per ieee 62.41.2. contd...... 164 the luminaire should be of class b serviceability. the led used in the luminaire shall be smd type only & shall be from either lumileds, osram, nichia, cree & apt electronics make or equivalent. the driver should be asphalt potted & should be a bis approved driver. the driver shall have operating voltage of 120v to 270v, pf≥0.95 @ full load, thd≤10% @ full load. the driver should be capable of withstand voltage stress of 440v for 8 hrs., should have an auto shutdown @ 325v(±15v) and have an auto recovery feature. the driver shall comply to iec61547 & iec 61000-3-2.the luminaire driver & it’s spd shall be of the same make/manufacturer as that of led luminaires.luminaire manufacturer must have in-house nabl accredited lab to conduct lm79, type test as per is10322 & fat before dispatch as per is 10322. the contractor must submit the nabl accreditation certificate for luminaire manufacturer along with sample approval. the led luminaire & its driver both should be bis registered. contractor shall submit the following reports before supply of material for approvals: lm79 issued by nabl accredited lab, lm80 issued by led manufacturer, type test report for luminaire as issued by nabl accredited lab, rohs compliance issued by led luminaire manufacturer, bis certificate for led luminaire & driver and including 1.2m long 32mm dia gi pipe light grade bend to shape and fixed using two nos clamps fabricated using ms flat iron 40x5mm including necessary nut bolts and washers and making electrical connection using 1.5sqmm, 3 core multi-stranded copper conductor pvc insulated and over all pvc sheathed cable form light fitting complete all as specified and directed 165 taking down ceiling fan 1200 / 1400 mm sweep of any capacity, sealing cable end, dismantling blades and removing fan and blades from existing position for depositing at mes store ward complete all as specified and directed. taking down fan, 166 s&f ceiling fan 230 volts, 1200 mm sweep having minimum air delivery 220 cfm with service value 6.00 bee, five star rating with brushless direct current (bldc) motor, with three blades, down rod, top & bottom canopy, rubber reel, clamps and other fixing accessories and connecting up by using three core flexible copper conductor cable complete all as specified and directed. 167 taking down the existing storage type water heater (geyser) of any capacity, type and size by disconnecting all electrical, mechnical and plumbing connections and depositing at mes store ward complete all as specified and directed. 168 s & f of hot water storage (geyser) 25 ltrs capacity, bee 5 star rated, vertical type, digital temperature display with suitable size of fastner and incl provision and connecting up of ss braided pipe with adopter for inlet and outlet water connection, copper element corrosion resistance antiscaling magnesium anode, having adjustable knob for temperature control and inner tank material of superior glassline coating / percelain enamel coating / titanium enamel coating / nano blue diamond glass coating / coating with single weld line tank and outer body material abs with high pressure with standing capacity upto 8 bar pressure, multiple safety systems for protection against dry heating, overheating and over pressure, ipx4 waterproof technology for longer product life having heating element 2 kw and minimum two year warranty on product, minimum 3 years warranty on heating element 5 years on tankcomplete all as specified and directed. 169 m & l submain wiring with 2 runs of single core 6sqmm pvc insulated unsheated multistranded 1100 volts grade with copper conductor drawn through and including non-metalic rigid in pvc casing and caping isi marked and itsaccessoriesincluding one run of single core 6 sqmm pvc insulatedunsheated multistranded 1100 volts grade with copper conductor cable as earth continuty conductor along with the wiring and connected from db to db/main board/plug and socket for accomplete all as specified and as directed. 170 s&f single pole enclosure with a two pin and earth plug and socket (ac box) complete with one double pole mcb 20 amps complete all as specified and directed. 171 s&f sheet metal enclosures fordb, single pole & neutral, 12 way with 200 amps rated bus bar, double door, 240 volts complete all as specified and directed. 172 s&f sheet metal enclosures fordb, single pole & neutral, 8 way with 200 amps rated bus bar, double door, 240 volts complete all as specified and directed. 173 s&f sheet metal enclosures fordb, single pole & neutral, 4 way with 200 amps rated bus bar, double door, 240 volts complete all as specified and directed. 174 s&f isolator tpn, 415 volts, 63 amps complete all as specified and directed. 175 s&f mcb spn, 240 volts, 32 amps, 10 ka, 50 hz complete all as specified and directed. 176 s&f mcb sp, 240 volts, 6-32 amps, 10 ka, 50 hz complete all as specified and directed. 177 s&f rcbos for earth leakage, overload & short circuit protection, four pole, 30ma, 240 volts, 63 amps complete all as specified and directed. 178 s&f rcbos for earth leakage, overload & short circuit protection, double pole, 30ma, 240 volts, 32 amps complete all as specified and directed. 179 m & l for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr deep below normal ground level, connected to db/pole/la etc and incl gi earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers, protected with and incl 15 mm dia light grade gi pipe, 20 mm dia gi pipe (medium grade) for watering, necessary earth work.pcc 1:3:6 type c1 concrete pit, rcc (1:1.5:3) type a1 pre-cast cover (54x54x5 cm) duly reinforced with and incl 8 mm dia tmt bar @ 150 mm c/c both ways, one lifting handle made of 8 mm dia tmt bar, embedded in pre-cast cover slab all as specified and shown in electrical plate no-3 of ssr part-i incl testing on completion alongwith including dismantling/taking down old unsv earth plates complete all as specified and directed.