tender for special repair of bldg no to-20 and ta-267 at army avn unit under ge 865 ews; 1 demolition of cement concrete (un reinforced) in ground floors and pavings not exc 15 cm thick (below or above ground level) and removing debris off the premises complete all as specified and/or as directed by engr-in-charge. 2 demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing debris off the premises, complete all as specified and/or as directed by engr-in-charge. 3 dismantling floor, hearth or wall tiling including cement mortarbedding (but including backing), removing rubbish off the premises complete all as specified and/or as directed by engr-in-charge. 4 dismantling wall and ceiling boards (fiber, pulp, insulation, blankets) etc. any thickness including covered fillets and supporting members, complete all as specified and/or directed by engr-in-charge. 5 dismantling unframed wooden fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc.under 40 sqcm in section, complete all as specified and/or directed by engr-in-charge. 6 demolition of precast concrete block walling built in cement mortar including all quoins, arches, pillars etc. complete all as specified and/or directed by engr-in-charge. 7 taking down cement plaster on brick/pcc block or concrete surfaces including racking out joints, hacking for key, scrubbing down with water etc., complete all as specified and/or as directed by engr-in-charge. 8 taking down chowkat or frame with shutters (without taking of shutters from the frame)not exc 1.5 sqm each any type of door (wooden, aluminium & steel etc.) complete all as specified and/or as directed by engr-in-charge. 9 taking down chowkat or frame with shutters (without taking of shutters from the frame)exc 1.5 sqm each but not exc 4 sqm each any type of door (wooden, aluminium & steel etc.) complete all as specified and/or as directed by engr-in-charge. 10 dismantling plain or corrugated steel sheeting any gauge or thickness including nanital or similar pattern complete all as specified and as directed by engr-in-charge. 11 dismantling wrought iron or mild steel work of any description not otherwise provided for angle iron or flat iron as in post and guard bars or grating, complete all as specified and/or directed by engr-in-charge. 12 m&l for9mm thick prelaminated particle boardmedium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with nails to timber frame work as in wall panelling, shelves/boarding complete all as specified and as directed. 13 m&l for9mm thick prelaminated particle boardmedium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with nails to timber frame work as in ceiling panelling, complete all as specified and as directed. 14 m&l for 6mm (5 ply) thick veneered decorative (knoty pine) plywood, grade 1 (with bwr resin) with decorative face veneers on one face, fixed with nails to timber frame work on wall complete all as specified and/or as directed by engr-in-charge. 15 all as per srl item no 14 above, but fixed in ceiling. 16 m&l french polishing on wood or wood based surface of any width or girth or any description, including cleaning and preparing the surface including a coat of wood filler on new surface with two or more coats to obtain the required finish complete all as specified and/or as directed by engr-in-charge. 17 m&l for 2nd class soft wood clean sawn as in battens for grids of ceiling & liningfixed with nails exc 13 sqcm and not exc 25 sqcm in section, complete all as specified and directed by engr-in-charge 18 m&l for 2nd class soft wood clean sawn as in battens for grids of ceiling & liningfixed with nails exc 6 sqcm and not exc 13 sqcm in section, complete all as specified and/or as directed by engr-in-charge. 19 m&l for covered fillets of standard hard board not less than 6mm thick and up to 40mm wide and fixing with screws complete all as specified and/or as directed by engr-in-charge. 20 m&l for 75 mm thick pcc 1:3:6 type c-2 (using 20mm graded aggregate) as plinth protection finished even and smooth with out using extra cement, complete all as specified and/or as directed by engr-in-charge. 21 m&l forming contraction (dummy) joints 65 mm deep x 10mm wide, filled with sealing compound grade a in plinth protection, complete all as specified and/or as directed by engr-in-charge. 22 m&l for pcc 1:4:8, type d2 (using 40mm graded crushed aggregate) as in mass concrete and filling of foundation, complete all as specified and/or as directed by engr-in-charge. 23 m&l precast solid blocks in cement concrete 1:3:6 type c-1 (20mm graded crushed stone aggregate) as in block masonry, exc.10cm in width and set in cement mortar 1:6, complete all as specified and/or directed by engr-in-charge. 24 m&l for 15mm thick rendering on fair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 4 including mixing of liquid water proofing compound as per manufacturers instructions complete all as specified and as directed by engineer-in-charge. note : wpc will be measured and paid separately. 25 supply only integral liquid water proofing compound.make : pidilite/sika/asian paints. 26 m&l for preparation of new plastered wallsurface of any description and applying two coats of cement based paint over a coat of primer complete all as specified and/or as directed by engr-in-charge. 27 s&fpowder coated (minimum thickness of powder coating 50 micron) anodised aluminium frames for door, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and/or as directed by the engr-in-charge. 28 m&l for powder coated aluminium door shuttlers, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, hinge type b-21 100 mm longs (3 nos) suitable handle (2 nos) (glass / wiremesh should be measured seperately) complete all as specified and/or as directed by engr-in-charge. 29 s&f anodised aluminium window and ventilator shutters, including aluminium jali fixed in one side, side hung type without sash, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150mm long (1 no) hinges type b-21 100mm long (2 nos) suitable handle (1 no) etc. complete all as specified and/or as directed by engr-in-charge. 30 m&l sheet glass 5.5mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc. 0.50 sqm in each pane complete all as specified and as directed. 31 s&f in repairs galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and/or as directed by engr-in-charge. 32 s&f 150mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and/or as directed by engr-in-charge. 33 s&f 100mm long aluminium anodized, barrel tower bolt of extruded section, complete all as specified and/or as directed by engr-in-charge. 34 s&f 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and/or as directed by engr-in-charge. 35 s&f 100 mm size extruded aluminium alloy handles, fabricated type, anodized, complete all as specified and/or as directed by engr-in-charge. 36 s&f in repair aluminium (die cast) body door closer hydraulically designation no 3 universaltype suitable for door shutter of 851 to1000mm in width and weight61 to 80 kg complete all as specified and/or as directed by engr-in-charge. 37 s&f in repair 1200mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick ac building board or commercial ply wood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and/or as directed by engr-in-charge. 38 s&f floor door stopper (length of cover plate) 150mm long aluminium alloy body and tongue anodised with hard drawn steel springfixed in floor complete all as specified and/or as directed by engr-in-charge. 39 s&f 75mm long aluminium anodized, butt hinges of extruded section type c-21, complete all as specified and/or as directed by engr-in-charge. 40 s&f 100mm long aluminium anodized, butt hinges of extruded section type b-21, complete all as specified and/or as directed by engr-in-charge. 41 s&f 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and/or as directed by engr-in-charge. 42 m&l for 25 mm thickpcc 1:2:4 type b1 (using 20mm graded stone aggregate) as in sub base of floorcomplete all as specified and/or as directed by engr-in-charge. 43 m&l light shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exc. 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles including 15 mm thick screed in cement mortar (1:4) as in floors etc.complete all as specified.make : johnson (daisy sf/gloria sf) or equivalent from kajaria/somany as approved by ge. 44 m&l for non - skid coloured ceramic joint free tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exc. 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and/or as directed by engr-in-charge. 45 m&l for glazed ceramic coloured tiles in vertical surfaces of size 450x350x7mm/ 350x250x7mmthick set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including rendering 10 mm thick in cement mortar (1:4) as in backing coat complete all as specified and/or as directed by engr-in-charge. 46 dismantling water tank exc. 250 not exc. 500 litre capacity and removing to store complete all as specified and/or as directed by engr-in-charge. 47 s&f rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in ssr part-i of capacity 500 litres including all accessories, complete all as specified and/or as directed by engr-in-charge. 48 s&fin repairs towel hanger with 6 nos of pin and600mm long chromium plated etc. complete all as specified and/or as directed by engr-in-charge. 49 dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. complete all as specified and/or as directed by engr-in-charge. 50 m&l for cement concrete 1:4:8, type d-2, (using 40mm graded stone aggregate) 75 mm thick as in sub -floors, sub- bases, floors and pavings, etc. complete all as specified and/or as directed by engr-in-charge. 51 m&l for chequered cement concrete tiles (glazed) 30cm x 30cm x 20mm thick, set, pointed & jointed in neat cement slurry in floors polished with grey cement & pigments, laid over 20mm thick cement screed base (1:6) complete all as specified and/or as directed by engr-in-charge. 52 s&f ms rolled sections in main and cross beams, hip and jack rafters; purlins where connected to common rafters running rails and guids for sliding doors; fixed with angle cleats or other connecting plates and similar work confirming to fe-290, gde-e-165, complete all as specified and/or directed by engr-in-charge. 53 m&l for preparation new steel surfaces of any description, not otherwise described, over 10cm width/girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and/or as directed by engr-in-charge. 54 s&f pre- painted galvalume aluminum zinc coating gi based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and/or directed by engr-in-charge. 55 s&f pre- painted galvalume aluminum zinc coating gi based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and/or directed by engr-in-charge. 56 s&f in repair 19mm dia mild steel, chromium plated curtain rods,withbrackets, end bulbs complete all as specified and/or directed by engr-in-charge. 57 s&f in repair vitreous china wash basin fancy type pedestal pattern, white, flat back, size 550 x 400mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe, complete all as specified and/or directed by engr-in-charge. 58 s&f in repairs 15mm bore cp wash basin mixer for mixing hot & cold water copper alloy fancy type high pressure screwed for iron pipe, complete all as specified and/or as directed by engr-in-charge. 59 s&f in repair towel rod brass cp 60 cm long between flanges and including all accessories like brackets/ screws etc as recommended by manufacturer and complete fixed in position complete all as specified and/or directed by engr-in-charge. 60 s&f in repairs 15mm dia angle stop valves, fancy type chromium plated with long shank and cast copper alloy, screwed down high pressure screwed both ends for iron pipes complete all as specified and/or directed by engr-in-charge. 61 taking up or down 25 mm bore steel tubing and connections and set aside for re-use or removal to store, complete all as specified and/or directed by engr-in-charge. 62 taking up or down 32 mm bore steel tubing and connections and set aside for re-use or removal to store, complete all as specified and/or directed by engr-in-charge. 63 s&f 25mm dia3 layer pp-r polypropylene random copolymer concealedpipes sdr 7.4 (pn 16) uv stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all pp-r plain & brass threaded polypropylene random fittings fixed complete all as per manufacture instructions and as directed by engr-in-charge. 64 s&f 32mm dia3 layer pp-r polypropylene random copolymer concealedpipes sdr 7.4 (pn 16) uv stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all pp-r plain & brass threaded polypropylene random fittings fixed complete all as per manufacture instructions and as directed by engr-in-charge. 65 s&f in repairs, 15mm bore, pvc connection pipe 600 mm long with ptmt nuts at both ends, complete all as specified and as directed. 66 s&f in repair 600x450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick ac building board or commercial ply wood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and/or directed by engr-in-charge. 67 taking down carefully copper/aluminium point wiring (light, fan, socket and power point) including complete fittings such as switches, ceiling rose, regulators, socket etc. and removing material from site and making good disturbed surfaces of walls, floors/ceiling to match the existing surface all as specified and directed by engr-in-charge. 68 point wiring complete with 1.5 sqmm nominal area of copper conductor multi stranded pvc insulated and unsheathed 1100 volts cable drawn through & including pvc casing & caping with standard accessories such as elbows, tees, junctions etc. and pvc moulded terminal box with top cover of including pvc insulated unsheathed solid 1.5 sqmm copper conductor cable as continuous earth lead complete all as specified and/or directed by engr-in-charge for the followings:- 69 one light/exhaust fan point controlled by one way switch. 70 one switch socket outlet 6 amps, 230 volts point on same board. 71 one switch socket outlet 6 amps, 230 volts point on independent board. 72 all as per srl item no 68 above, but using cables 4 sq mm size. 73 s&f switch piano flush button single pole 6 amps 230 volts one way complete all as specified and/or directed by engr-in-charge. 74 s&f switch socket outlet 2 in 1, 5 pin, 6 amps flush type 230 volts complete all as specified and/or as directed by engr-in-charge. 75 s&f switch socket combination outlet multi purpose 3/5 pin 6 amps and 16 amps 230 volts complete all as specified and/or directed by engr-in-charge. 76 s&f ceiling rose, surface bakelite three terminals complete all as specified and/or directed by engr-in-charge. 77 s&f inreplacement of sheet metal enclosure for dbs double door when mcbs to be used single pole & neutral 240 volts 12 ways complete all as specified and/or directed by engr-in-charge. 78 s&f mcb spn 40 to 63 amp 240 volts ac isi marked complete all as specified and/or directed by engr-in-charge. 79 s&f mcb sp 6-32 amps. 240 volts50 hz complete all as specified and/or directed by engr-in-charge. 80 taking down old unserviceable exhaust fan and supply and fix exhaust fan, steel body ac single phase. 230v of size 300m sweep with blades, frame and louvers, complete all as specified and/or as directed by engr-in-charge.note : old unsv fan shall be deposited to mes e/m store. 81 s&f in replacement led light fitting 1x20w, 220v, ac decorative box type with driver, holder including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and/or as directed by engr-in-charge. 82 m&l for submain wiring along with earth wire with the following sizes of frlsh pvc insulated copper conductor, single core cable in surface/recessed as required in pvc casing caping wire size 2x2.5 sqmm + 1x2.5 sqmm earth wire including taking down the existing one complete all as specified and/or directed by engr-in-charge. 83 m&l for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to and including 4 mm dia gi wire as earthing lead, by means of bolts, nuts, check nuts and washers of galvanised iron all as shown in electrical plate no 3 of mes ssr part i and testing on completion including excavation and earth work in any type of soil, pcc (1:3:6) type c1 chamber, ms frame and cover 6 mm thick in cement concrete (1:2:4) type b1 reinforced with welded steel wire fabric or xpm (weight not less than 4 kg per sqm) with cast iron frame, funnel with wire mesh, gi watering pipe 20mm dia medium grade and lugs complete all as specified and/or as directed by engr-in-charge.