tender for general-improvement work-improvements and providing bm & bc works to malappuram - parappanangadi road b/w ch. 17/700 and 20/510 in vengara lac-general civil work - road surface 2 3.6:excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m 3 3.15:scarifying the existing bituminous road surface to a depth of 50 mm and disposal of scarified material with in all lifts and lead upto 1000 metres by mechanical means 4 3.16:construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2. 5 3.17:construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of table 300-2. 6 od42850/2025-2026:supplying and filling with granular material in the slushy area under culvert culvert bed to achieve adequate bearing strength and for drainage layer laid in the line and level ,compacted with plate vibrator etc complete (item no 13.9.a). 7 4.1.b.1:construction of granular sub-base by providing graded material, spreading in uniform layers with a motor grader on a prepared surface, mixing by mix in-place method with rotavator at omc, and compacting with a vibratory roller to achieve the desired density, complete as per clause 401. grading-v - for sub-base cum drainage layer - mix in place method 8 4.12:providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at omc in mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density. 9 5.1.a:providing and applying primer coat with bitumen emulsion ( ss) on prepared surface of granular base including clearing of road surface and spraying primer at the rate of 0.70 - 1.0 kg/sqm using mechanical means. 10 5.2.b:providing and applying tack coat with bitumen emulsion (rs) using emulsion pressure distributor at the rate of 0.25 - 0.30 kg per sqm on the prepared granular surface cleaned with mechanical broom. 11 5.2.a:providing and applying tack coat with bitumen emulsion( rs) using emulsion pressure distributor at the rate of 0.20 - 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom. 12 5.3.2.a:providing and laying bituminous macadam with 80-100 tph hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with a bituminous binder (vg 30), transported to the site, laid over a previously prepared surface with paver finisher to the required grade, level, and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction for grading ii - (19 mm nominal size) 13 5.6.2.a:providing and laying bituminous concrete with 80-100 tph hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with a bituminous binder( nrmb) @ 5.4 percent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level, and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per morth specification clause no. 507 complete in all respects for grading - ii (13.2 mm nominal size) 14 55.24:providing and laying bituminous concrete with 80-100 tph hot mix plant producing an average out put of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder (nrmb) @ 5.4 percent of mix and filler, transporting the hotmix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per morth specification clause no. 507 complete in all respects (using 7% shredded plastic)grading - ii (13.2 mm nominal size) 15 drain, side protection and berm concrete 16 2.4.2.a:dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including t&p and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metrescement concrete grade m-15 & m-20 - by mechanical means 17 2.4.2.b:dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including t&p and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metresprestressed / reinforced cement concrete grade m-20 & above - by mechanical means 18 2.4.4.d:dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including t&p and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metresdismantling stone masonry - dry rubble masonry 19 3.13.1.b:earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work. ordinary soil - mechanical means - (depth upto 3 m) 20 3.13.2.b:earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work.
ordinary rock (not requiring blasting) - mechanical means
21 12.4:plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days. 22 12.8.a.1:plain/reinforced cement concrete in open foundation complete as per drawing and technical specifications.pcc grade m15 23 od164171/2025-2026:plain/reinforced cement concrete in open foundation complete as per drawing and technical specifications
pcc grade m2020mm aggregates (without formwork) (12.8.b &12.8.1.c) 24 12.8.1.c.1:plain/reinforced cement concrete in open foundation complete as per drawing and technical specificationsrcc grade m20 - using concrete mixer 25 12.40:supply, fitting and placing un- coated hysd bar reinforcement in foundation complete as per drawing and technical specifications 26 od137303/2025-2026:wrought iron and mild steel welded work (using angles square bars, tees and channel grills, grating frames, gates and tree quads of any size and design etc including cost and screens and welding rods or bolts and nuts complete fixed in position but without the cost of excavation and concrete for fixing which will be paid separately 27 od42851/2025-2026:pvc weep holes- providing weep holes using 75mm dia. pvc pipes working pressure 4kg /sq.cm including cost of materials, conveyance, labour charges etc. complete.( derived from 60.6 ) 28 55.22:supplying and laying interlocking tile 100 mm or nearest size thickness, minimum strength m 40 including providing a layer of 6 mm aggregate for 5 cm thickness, then laying interlock cobbles in lines and levels as per the directions of the departmental officers at site inclusive of all cost & conveyance charges etc.; complete. 29 od157249/2025-2026:engaging man mazdoor where ever required 30 road safety work 31 8.13:providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads on bituminous surface @ 250 gms per sqm area, the thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35. the finished surface to be level, uniform, and free from streaks and holes. 32 8.35:providing and fixing reflective road studs (raised pavement marker) of category a made out of asa/hips/abs moulded body with shanks and conforming to astm d 4280, strong enough to support a load of more than 13.635 t when tested in accordance with astm d 4280, reflective panel confirming to astm d 788, and reflectivity conforming to clause 804.4. including installation, drilling, fixing with adhesive etc. with 2 years warranty for the road stud as well as for in field performance as per clause 804.7.3 road markers/road stud with lense reflector :- 33 8.4.1:providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign with 7years warranty manufactured as per irc :67 made of type iv micro prismatic grade sheeting vide clause 801.3.3 fixed over aluminum sheeting, 2 mm thick/aluminum composite material sheeting 4 mm thick with suitable back supporting frame of ms angle 25x25x3 and supported on gi pipe pole 50mm nb confirming to is 1239 firmly fixed to the ground by means of properly designed foundation with m 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer and as per approved drawing and clause 801 including lettering symbols etc. 90 cm equilateral triangle 34 8.4.10:providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign with 7years warranty manufactured as per irc :67 made of type iv micro prismatic grade sheeting fixed over aluminum sheeting, 2 mm thick/aluminum composite material sheeting 4 mm thick with suitable back supporting frame of ms angle 25x25x3 and supported on gi pipe pole 50mm nb confirming to is 1239 firmly fixed to the ground by means of properly designed foundation with m 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer and as per approved drawing and clause 801 including lettering symbols etc. 90 cm circular 35 8.4.7:providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign with 7years warranty manufactured as per irc :67 made of type iv micro prismatic grade sheeting fixed over aluminium sheeting, 2 mm thick/ aluminium composit material sheeting 4 mm thick with suitable back supporting frame of ms angle 25x25x3 and supported on gi pipe pole 50mm nb confirming to is 1239 firmly fixed to the ground by means of properly designed foundation with m 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer and as per approved drawing and clause 801 including lettering symbols etc. 90 cm high octagon 36 8.5:providing and fixing of direction and place identification retro-reflectorised sign with 7 years warranty manufactured as per irc :67 made of type iv micro prismatic grade sheeting fixed over aluminium sheeting, 2 mm thick/ aluminium composit material sheeting 4 mm thick with area not exceeding 0.9 sqm, with suitable back supporting frame of ms angle 40x40x6 and supported on gi pipe pole 50mm nb confirming to is 1239 firmly fixed to the ground by means of properly designed foundation with m 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer and as per approved drawing and clause 801 including lettering symbols etc. 37 8.6:providing and fixing of direction and place identification retro-reflectorised sign with 7 years warranty manufactured as per irc :67 high intensity micro prismatic (type iv) grade sheeting fixed over aluminum sheeting, 2 mm thick/aluminum composite material sheeting 4 mm thick with an area exceeding 0.9 sqm, with suitable back supporting frame of ms angle 40x40x6 and supported on suitably designed gi pipe pole not less than 50mm nb , 2 nos. confirming to is 1239, firmly fixed to the ground by means of properly designed foundation with m 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer and as per approved drawing and clause 801 including lettering symbols etc. 38 55.10.1:providing and erecting retro-reflectorised object hazard marker 300mm x 900mm providing and erecting retro-reflectorised object hazard marker sign with 07 years warranty, manufactured as per irc 67 using type iv astm d 4956-09 micro prismatic retro reflective sheeting fixed over aluminium sheetig, 2 mm thick / aluminium composit material sheeting 4 mm thick with suitable back support frame and supported on a mild steel angle iron post 75mmx75mmx6mm, firmly fixed 30cm above ground level by means of properly designed foundation with m 15 grade cement concrete 30cmx30x45cm, 45cm below ground level including painting all non-reflective faces with epoxy paint 2 coats over epoxy primer as per approved drawing and clause 801.300 mm x 900 mm 39 8.4.12:providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign with 7years warranty manufactured as per irc :67 made of type iv micro prismatic grade sheeting fixed over aluminum sheeting, 2 mm thick/aluminum composite material sheeting 4 mm thick with suitable back supporting frame of ms angle 25x25x3 and supported on gi pipe pole 50mm nb confirming to is 1239 firmly fixed to the ground by means of properly designed foundation with m 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer and as per approved drawing and clause 801 including lettering symbols etc. 50cmx 60 cm rectangular (single chevron etc.) 40 55.14:providing and fixing retro-reflectorised ceramic tilesproviding and fixing retro-reflectorised ceramic tiles of size 10cmx20cm using high intensity micro prismatic (type iv) grade sheeting with 7 years warranty fixed over ist quality ceramic glazed tiles including cost of glue, cutting charges, fixing with suitable adhisive on concrete or other surface etc complete. 41 8.14.2:reinforces cement concrete m 15 grade kilometre stone of standard design as per irc:8-1980, fixing in position including painting and printing etc ordinary kilometer stone ( precast) 42 8.14.3:reinforced cement concrete m15 grade hectometer stone of standard design as per irc-8-1980, fixing in position including painting and printing etc hectometer stone (precast) 43 8.8:painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces 44 8.15:supplying and installation of delineator (roadway indicators) posts 80- 100cm high above ground level, pained black, and white in 15 cm wide strips, fitted with min. 80 x 100 mm rectangular or 75 mm dia circular retro reflectorized panels at the top with minimum visibility of 300m with provisions to prevent edge lifting and vandalisam, and conforming to clause 806 , irc-79 and the drawings including fixing to ground (the deleniator shall be of approved type as per specification) 45 od137337/2025-2026:providing and fixing of defect liability boards (1.20 m x 0.60 m) made of printing reflective type fixed over aluminium composite panel with suitable back supporting frame of ms angle 25x25x3 and supported on suitably designed gi pipe pole not less than 50mm nb , 2 nos. confirming to is 1239, firmly fixed to the ground by means of properly designed foundation with m 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, on ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer and as per approved drawing and clause 801 including lettering symbols etc.