tender for annual plan-ajanur gp-pro.no.424/25-26-maintenance of madiyan school-general civil work - dismantling tiled roofing with battens, boarding etc. complete including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. 3 15.14.1:dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead:of sectional area 40 square centimetres and above 4 15.12.1:dismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead:of area 3 sq. metres and below 5 50.9.3.1:providing and fixing paneled or paneled and glazed shutters for doors, windows and clerestory windows, 30 mm thick shutters including isi marked m.s. pressed butt hinges bright finished of required size with necessary screws, excluding paneling which will be paid for separately, all complete as per direction 0f engineer in- charge. using anjili/ jack wood 6 50.9.4.1:providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured) paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick using good quality anjili/ jack wood 7 13.99.1:painting with synthetic enamel paint of approved brand and manufacture ofrequired colour to give an even shade :one or more coats on old work 8 50.9.15.5:providing and fixing iron hooks and eyes: 100 mm 9 9.48.2:providing and fixing m.s. grills of required pattern in frames of windows etc. with m.s. flats, square or round bars etc. including priming coat with approved steel primer all complete.fixed to openings/ wooden frames with rawl plugs screws etc 10 10.25.2:item shifted to sub head 14 as item 14.73item shifted to head 14 as item 14.74steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 11 2.8.1:earth work in excavation by mechanical means (hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.all kinds of soil 12 od185415/2025-2026:laterate masonry with neatly dressed laterate stone of size 35x20x20cm or nearest size in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc. 13 od178984/2025-2026:laterate masonry with neatly dressed laterate stone of size 35x20x20cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc. 14 12.48:providing & fixing on roof pressed clay tile (mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately) 15 od185379/2025-2026:providing & fixing on reroof departmental pressed clay tile (mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately) 16 13.1.2:12 mm cement plaster of mix:1:6 (1 cement : 6 fine sand). 17 13.45.1:finishing walls with textured exterior pint of required shade:new work (two or more coats applied @ 3.28 ltr/ 10 sqm ) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm 18 od186771/2025-2026:steel work for purlin/single section with ms pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete 19 12.50:providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by engineer-in-charge. the sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with epdm seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 20 od186773/2025-2026:providing and fixing 150 mm half cut pvc pipe over flat iron brackets 20x5 mm size including cost and conveyance of all materials and all labour charges etc. 21 50.18.9.18.2:providing and fixing pvc pipes including fixing the pipe with clamps/clips at 1.00 m spacing. this included jointing of pipes with one step pvc solvent cement and testing of joints complete as per direction of engineer-in-charge 75 mm dia 4 kfg/cm2 - external work - exposed on wall 22 21.1.1.1:providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is : 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminnium snap beading for glazing /paneling, c.p. brass/ stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge.(glazing, paneling and dash fasteners to be paid for separately):for fixed portionanodised aluminium (anodised transparent or dyed to required shade according to is : 1868, minimum anodic coating of grade ac 15) 23 21.1.2.1:for shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of epdm rubber/ neoprene gasket required (fittings shall be paid for separately)anodised aluminium ( anodised transparent or dyed to required shade according to is : 1868, minimum anodic coating of grade ac 15) 24 21.3.1:providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer - in -charge. ( cost of aluminium snap beading shall be paid in basic item):with float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) 25 50.9.13.1:supplying and fixing anjily wood wrought and put up for roof members including cost and conveyance of materials etc. complete . 26 50.9.14.1:supplying and fixing anjily wood reapers of size 50x25 mm with wire nails including cost and conveyance of materials etc. complete. 27 12.49:providing & laying on roof pressed clay tile ridge (mangalore tile) of 20 mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately ). 28 16.68:providing and laying 60 mm thick factory made cement concrete interlocking paver block of m - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of engineer-in-charge. 29 10.16.3:steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.electric resistance or induction butt welded tubes 30 4.1.4:providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level:1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources)