tender for annual plan-128/26-kalluvila-panimoola road in ward 12-pothencode gp-general civil work - road work 2 od90270/2025-2026:surface dressing of ground including removing vegetation and inequalities not exceeding 150 mm deep and disposal of rubbish lead up to 50 m and lift 1.5 m etc. complete. 3 3.2:preparation of foundation for embankmentscarifying existing bituminous surface to a depth of 150 mm by mechanical meansscarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per technical specification clause 301.4. 4 4.9:wet mix macadamproviding, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at omc in mechanical mixer (pug mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kn weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per tables 400.11 & 400.12 and technical specification clause 406.by mechanical means with 1 km lead 5 5.5.b.2a:modified penetration macadam 75 mm thick using bitumen s-65construction of penetration macadam over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kn static roller to achieve the desired degree of compaction as per technical specification clause 506.(b) 75 mm thick :- (ii) bitumen (s-65) 6 5.1.1a:prime coat :- low porosityproviding and applying primer coat with bitumen emulsion (ss-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per technical specification clause 502 7 5.2.3a:tack coat providing and applying tack coat with bitumen emulsion (rs-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with hydraulic broom as per technical specification clause 503. 8 5.2.1a:tack coat providing and applying tack coat with bitumen emulsion (rs-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with hydraulic broom as per technical specification clause 503. 9 5.11.1.a.2a:mix seal surfacing - manual means - type a - bitumen s-65providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (type-a) or 13.2 mm to 0.9 mm (type-b) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kn static roller and finishing to required level and grades as per technical specification clause 509by manual means :- type a(ii) bitumen (s-65) 10 75.8.1:providing plain cement concrete for road work cc 1:2:4 (1 cement: 2 fine aggregate: 4course aggregate) laid to required slope and camber in panels (@ 3 m c/c) as requiredincluding compaction, finishing and tamping etc .complete. max. size of courseaggregate not exceeding 25mm , mixed in concrete mixer etc complete as perspecification (i) nominal mix (1:2:4) 11 75.8.1.1.a:providing plain cement concrete for wearing coat cc 1:2:4 (1 cement: 2 fine aggregate:4 course aggregate) laid to required slope as required including compaction, finishingand tamping etc .complete. max. size of course aggregate not exceeding 25mm , mixedin concrete mixer etc complete as per specification (i) nominal mix (1:2:4) 12 od96975/2025-2026:supplying fixing name board 70x60cm installed in the appropriate place visible to the made of brick wall with granite plaque should be inserted and engraving letters etc.. complete as per the direction of department officers at site.