tender for sahu gopinath girls inter college bareilly. (alankar yojna), 1 boq 2 demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of engineer - in- charge. dsr 15.3 3 scraping old white or colour wash including disposal of refuse as directed by the engineer-in-charge within distance of 60 mt. (200 ft.).pwd sor s.no 708 4 demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge(.nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) dsr 15.2.1 5 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level :1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) dsr 4.1.8 6 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. dsr 15.56 7 12 mm cement plaster :1:6 (1 cement : 6 coarse sand) dsr 13.4.2 8 6 mm cement plaster of mix :1:3 (1 cement : 3 fine sand) in ceiling dsr 13.16.1 9 providing and laying vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to i.s. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.(size of tile 600x600 mm) dsr 11.46.2 10 dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead (:of area 3 sq. metres and below) dsr 15.12.1 11 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). dsr 5.3 12 brick work with common burnt clay f.p.s (non modular) brick of class designation 7.5 in super structure above plinth level up to floor v level in all shapes and sizes in : cement mortar 1:6 (1 cement : 6 coarse sand) dsr 6.4.2 13 1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) dsr 4.1.3 14 thermo-mechanically treated bars work such as in reinforced concreted or reinforced brick work (when not included in overall rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage. dsr 5.22.6 15 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. dsr 13.80 16 distempering with 1st quality acrylic distemper (ready mixed) having voc content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturers specification.new work (two or more coats) over and including water thinnable priming coat with cement primer having voc content less than 50 gram/litre dsr 13.41.1 17 finishing walls with acrylic smooth exterior paint of required shade :new work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) dsr 13.46.1 18 providing 10 mm thick plaster of paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately):( flat surfaces) dsr 13.31.1 19 painting steel work with deluxe multi surface paint to give an even shade. two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture dsr 13.48.3 20 providing and fixing pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board is : 3087 marked, with one side decorative and other side balancing lamination grade i, type ii exterior grade is : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately).(18 mm thick ) dsr 9.18.1 21 l/f of 19.00 mm thick black granite top over the laboratory counter, i/c rounding of edges and polishing as per d.s.r. 8.2.2.2 22 providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position:.second class sal wood complete of work as per dsr no. 9.1.2. 23 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters (:35 mm thick including isi marked stainless steel butt hinges with necessary screws) dsr 9.21.1 24 providing and fixing 30 mm thick kiln seasoned selected planks of sheesham wood panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, …….. (d.s.r.-9.5.3.2) 25 providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :4.0 mm thick glass panes dsr 10.30.1 26 providing and fixing m.s. grills of required pattern in frames of windows etc. with m.s. flats, square or round bars etc. including priming coat with approved steel primer all complete.fixed to steel windows by welding dsr 9.48.1 27 providing and fixing 2nd class teak wood wooden moulded beading 50x20 mm to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete:as per dsr 9.40.1.2 28 providing and fixing fly proof galvanised m.s. wire gauze to windows and clerestory windows using galvanised m.s. wire gage with average width of aperture 1.4 mm in both directions with wire of dia. 0.63 mm.with 12 mm mild steel u beading. dsr 9.51.2 29 providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). complete.as per dsr 9.53 30 providing and fixing aluminium sliding door bolts,300x16 mm isi marked anodised (anodic coating not less than grade ac 10 as per is : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : as per dsr. 9.96.1 31 providing and fixing aluminium tower bolts,300x10 mm isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. completer as per dsr 9.97.1 32 providing and fixing aluminium tower bolts,150x10 mm isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. completer as per dsr. 9.97.4 33 providing and fixing 125mm aluminium handles, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : completer as per dsr 9.100.1 34 providing and fixing lsi marked aluminium butt hinges 75x45x3.2 mm anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete:. as per s.i. 9.95.8 35 s/f of informatory sign board.........i/c painting,writing & fixing at site.... complete. 36 s/f of c.p brass waste jali 100mm dia complete. 37 s/f of p.v.c. pipe 100mm dia including all complete. s.no 730 38 providing and placing on tarees polithene water storage tank as per dsr 18.48. 39 providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre/8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. dsr 17.78 40 providingandfixing wash basin with c.i.brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting andmaking good the walls where required :white vitreous china wash basin size 550x400 mm with a pair of 15 mm c.p. brass pillar taps dsr 17.7.3 41 providing and fixing stainless steel a isi 304 (18/8) kitchen sink as per is:13983 with c.i. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :(470x420 mm bowl depth 178 mm) dsr 17.10.2.3 42 providing & fixing pvc waste pipe for sink oncluding pvc waste fitting complete (32mm dia) dsr 17.28.2.1 43 providing and fixing ptmt bottle trap for wash basin and sink.bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms. dsr 17.70.2 44 providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :(rectangular shape 1500x450 mm) dsr 17.32.4 45 providing and fixing toilet paper holder :(c.p. brass) dsr 17.34.1 46 providing and fixing ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less than 105 gms. dsr 17.71 47 providing & fixingptmt towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealedfittings arrangement of approved quality and colour weighing not less than 88 gms dsr 17.72 48 providing and fixing ptmt towel rail complete with brackets fixed wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms dsr 17.73.2 49 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge..internal work - exposed on wall( 15 mm dia nominal bore) dsr 18.7.1 50 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge..internal work - exposed on wall( 20 mm dia nominal bore) dsr 18.7.2 51 providing and fixing of gun metal gate valve with ci wheel of approved quality (screwed ends) (25mm dia, nominal bore) dsr 18.17.1 52 providing and fixing c.p. brass bib cock of approved quality confirming to is:8931(15mm nominal bore) dsr 18.49.1 53 providing and fixing c.p. brass long body bib cock of approved quality conforming to is standards and weighing not less than 690 gms.(15mm nominal bore) dsr 18.51.1 54 p/f of c.p. brass stopcock of 15mm dia nominal bore…….. including all complete of work.as per dsr 18.52.1. 55 providing and fixing c.p.brass angle valve for basin mixer and geyser points of approved quality conforming to is 8931 a) 15 mm nominal bore. dsr 18.53.1