tender for special repair to bldg no. t-11 under ge 860 ews; 1 dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering or wall etc, complete all as specified and directed. 2 dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed by engr-in-charge. 3 s&f rolled ms rooftrusses ( framed ) , trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing ( beam, tee, angle, channel or flat sections ) including distance pieces, cleats etc conforming to fe-290 gde e-165 ) , complete all as specified and directed. 4 fixing only pre-painted galvalume aluminum zinc coating gi based plain or corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws, complete all as specified and directed. 5 m&l preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified 6 demolition of concrete ( un-reinforced ) including tiles / kota slab etc. in ground floor and paving etc in exec 15 cm thick below or above gl. complete all as specified and directed. 7 m&l for 100mm thick cement concrete type b-2, 1:2:4 using 40mm graded stone aggregate as in floor, finishing the surface even and smooth without using extra cement complete all as specified. 8 taking down of chowkats with shutter ( without taking of shutter from frame ) exc 1.5 sqm but n, exc 4.0 sqm each complete all as specified and directed by engr-in-charge. 9 s&f of 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by engr-in-charge. 10 s&f of 30mm thick, flush shutters, solid core construction, with block board core and plywood face panels, covered with decorative face veneer with lipping / frame to match on both sides, fitted to chowkats complete all as specified and directed by engr-in-charge. 11 m&l for coloured vitrified ceramic tiles dark shade 10 mm thick ( square / rectangular ) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc, set and jointed in neat cement slurry and pointed in whiteor coloured cement to matchincluding screed bed 15mm thick in cm 1:6 including dismantling floor, hearth or wall tiles complete all as specified and directed by engr-in-charge. 12 m&l for 15 mm thick rendering in cm 1:4 on fair faces of brickwork or concrete surfaces finished fair and evenincluding taking down cement plaster on brick or stone walls etc.including racking out joints, hacking for key scrubing down with water&receive plaster upto double story heightcomplete all as specified and as directed. 13 m&l for 10 mm thick rendering in cm 1:6 on fair faces of brickwork or concrete surfaces finished fair and even including taking down cement plaster on brick or stone walls etc.including racking out joints, hacking for key scrubing down with water&receive plaster upto double story heightcomplete all as specified and as directed. 14 m&l preparation of new plastered or unplastered surfaces and applying two coats of oil bound distemper on wall over a coat of alkali resistant primer over two coat of wall care putty ( water proof ) complete all as specified and darected. 15 m&l for preparation of new plastered surfaces of wall and applying two coats of 100 % premium acrylic emulsion paint having voc less than 50 gm / ltrs and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqm all as per the manufacturers instructions, complete all as specified and directed by engr-in-charge. 16 m&l for pre-cast cement concrete block masonry type c1, ( 1:3:6 ) ( using 20 mm graded crushed stone aggregate ) with solid blocks, exc. 10 cm in width and setting in mortar 1:6 including demolition of stone / boulder masonary work built in cm including all quoins, arches, pillars etc & removing from site.complete all as specified and directed. 17 s&f of 100mm size, butt hinges, cold rolled steelwith screw, medium weight , isi marked complete all as specified and directed by engr-in-charge. 18 s&f 200 mm long aluminium, anodised, barrel tower bolt, fixed with screws complete all as specified and directed by engr-in-charge. 19 s&f 150 mm size, extruded brass handles fabricated type polished complete all as specified and directed by engr-in-charge. 20 s&f of 300 mm long, brass, sliding door bolts, with sand or die-cast brass hasp, staple ( bolt type ) and fixing bolt with rolled or drawn brass bolts complete all as specified and directed by engr-in-charge. 21 dismantling wall and ceiling boards ( fibre, insulation etc or insulation boards, slabs, blankets any thickness including cover fillets complete all as specified and directed.note:- taking down carefully old electric fiitting recessed mounted light fittings / ceiling complete with all accessories and making necessary electric connection, complete all as spd & directed by engr-in-charge 22 s&f of coloured pvc designer modular wall cladding 5 to 6 mm thick with air gap, installed with necessary fixing gi channel or frame with end joints on edges ( designed colour patterns as per directed by engr - in- charge ) . the frame work will be fixed to wall using aluminium screws complete all as specified and as directed by engr-in- charge .note : if necessary size of the frame work / wall paneling will be changed as per site requirement. 23 stage floor ( wooden flooring ) .m&l for sdc laminated flooring 8mm thick of any coloured, manufactured by direct pressure laminated ( dpl ) wherein the empty abrasive aluminium oxide overlay alongwith metamine impregnated decorated film is directly fused with the back with flooring locking profile in designed with double click locking system on the length and single locking width alongwith desire locking strength, complete all as directed. 24 accoustic fabric cloth. providing and fixing 2 mm thick spun cord fabric glued cloth fixed directly to the existing wall paneling board.the color shade of fabric as approved by architect including all accessories, material and labour complete all as specified and directed by ge.note:- make confirming to is 1950 ( 1962 ) and specification as approved by ge. 25 accoustic measures ceiling.providing and fixing soft fiber ceiling 595 x 595 x 15 mm thick is made fine micro glass fibre as per the below mentioned specifications colour : plain white, core : soft fiber, suspended ceiling system which includes main-t of size 32 x 15 x 0.30 mm at every 1200 c / c and cross t of size 26 x 15 x 0.30 mm are fixed to the perimeter of wall with the suitable fasteners.the suspension is done with all accessories like soffit cleat, leveling clips & wire rods as per dwgs.t-grid system charasteristics : 0.9 nrc broadband sound absorption, highest for modular ceilings.white surface finish with fine monolithc texture or high light reflectance, less lighting requirements.black surface for full light absorption. at 1.5-3kgs / m2, does not contribute siginificantly to structural load of building including all accessories, material & labour complete all as directed by ge.note:- make confirming to is 1950 ( 1962 ) and specification as approved by ge. 26 synthetic flooring.providing and fixing of loope pile fiber : 100% bcf polypropilience yarn construction & type : soluthion dyed bulk continuous filament machin gauge & stich rate : 2.54mm ( 1 / 10 ) 39.4 rows / 100mm, 48 / 10 cms.construction : loop pile high low scroll graphic.density factor : 189, 600 tufts / sq.mtrs tufted pile weight & hight : 650 gm / sq.mtr, 6mm ( 5% + / - ) backing : primary : woven polyproplene, secondary : action back moth proffing : 20 newton flammability : ( astm d 2859-96 & cpsc-ft-170 ) 8 passes static generation : under 3 kv light fastness: 5+ usage area : commercial heavy duty like auditorium office 7 heacy traffic area with backing of 8mm thick armour fixing on the floor with using fevicol sr 505 solution and fixing the carpet above armour including all acessaries, material & labour complete all asdirected by ge. note:- make confirming to is 1950 ( 1962 ) and specification as approved by ge. 27 taking down carefully alluminium / copper point wiring complete for light, fan, socket or power point etc with fittings fixtures such as ceiling rose, holders, electric fittings, switchs, sockets, aluminium conductor cable with and incl wooden batten or fr pvc conduit and its accessories such as wooden gutties, rawl plugs, gi screws, aluminium clips, nails etc complete and removing the material from site and making good the disturbed surface of wall / floor / ceiling etc as original i.e. brick work, plastering, white washing, obd etc as required, complete all as specified and directed. 28 m&l for point wiring complete for one light point / exhaust fan point / bell point controlled by one 1-way switch / bell push, with 1.5 sq mm ( nominal area ) frls pvc insulated un-sheathed and stranded copper conductor cable isi marked and pvc concealed conduit isi marked of size 20 mm dia medium grade and pvc conduit fittings such as tees, bends, elbow, reducers with and including frls pvc insulated unsheathed 1.5 sqmm copper earth wire, connecting to common earth dolly with and incl metal flush box of suitable size for fixing modular switches / sockets etc and making good surface by wall panelling etc, complete all as specified and directed. note : 1. the cost ofmetal flush boxes and accessories etc is deemed to be included in quoted rate.2. in case cutting & chasing of conduit is encountered with any beam / column, the pvc casing & capping or surface conduit will be used to avoid any damage to the rcc portion.3. no cutting & chasing shall be done on ceiling surface for laying pvc conduit for ceiling fan point wiring etc, hence the pvc casing & capping or surface conduit will be used for the same. 29 all as per srl item no. 28here-in-before but for one socket outlet 3 pin, 5 amps on independent board. complete all as specified and directed. 30 all as per srl item no. 28here-in-before but for one socket outlet 3 pin, 5 amps on same board. complete all as specified and directed. 31 all as per srl item no. 28here-in-before but with 2.5 sq mmfrls copper wire with 1.5 sqmm frls copper earth wire for indpendent 15 amp point. complete all as specified and directed. 32 s & fin replacement of modularswitch1way 6a , 1modulecomplete all asspecified and directed. 33 s & fin replacement of modularswitch1way 16a , 1modulecomplete all as specified and directed. 34 s & f in replacement of modularbellpush 1way 6a , 1modulecomplete all as specified and directed. 35 s & fin replacement of modularsocket , 6 a , 5 pin , 2modulecomplete all as specified and directed. 36 s & fin replacement of modularsocket , 6 a / 16 a , 5 pin , 2modulecomplete all as specified and directed. 37 s & fin replacement of modularcoverplatewithframe 6 module. complete all as specified and directed. 38 s & fin replacement of modularcoverplatewithframe 4 module.complete all as specified and directed. 39 s & f in replacement of modularcoverplatewithframe 3 module. complete all as specified and directed. 40 s & fin replacement of modularcoverplatewithframe 2 module. complete all as specified and directed. 41 s & fin replacement of modularcoverplatewithframe 1 module. complete all as specified and directed. 42 s & fin replacement of modularmetalflashbox6module. complete all as specified and directed. 43 s & fin replacement of modularmetalflashbox4module. complete all as specified and directed. 44 s & fin replacement of modularmetalflashbox3module.complete all as specified and directed. 45 s & fin replacement of modularmetalflashbox1 / 2module. complete all as specified and directed. 46 s&f in replacement of electric call bell ding dong ac 230 volts single pole. complete all as specified and directed. 47 s&f, in repalcement, of lamp holder, metal cased, bakelite body, 230 volts, complete all as specified and directed. 48 s&f in replacement of led lamp 9 / 10w complete all as specified and directed. 49 s&f, in repalcement, of ceiling rose, two to three terminals, bakelite body, 230 volts, complete all as specified and directed. 50 s&f, in replacement of led lights fitting 1x 20w, 220v, ac decorative box type with driver, holder including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. 51 s&f, in replacement of led luminaire 600 mm x 600 mm, 35 / 36 watt, 220 v ac recessed type with high efficiency pmma diffuser soft glare free light complete with driver, holders & led lamp suitable for roof ceiling 6500k including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and directed. 52 s&f, in replacement of round shape 12 watt 220 volts ac recessed type with high efficiency pmma diffuser soft glare free light 6500 k complete with drivers, holders, led lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. 53 s & f in replacement led light fitting 1x9w / 1x10w bulkhead luminaires including led light driver holder connecting up with three core flexible copper conductor cable of suitable size. complete all as specified and directed. 54 m&l for sub main wiring with 2 run of 4 sqmm fr, pvc insulated, unsheathed and stranded copper conductor cable with and incl 4 sqmm ( nominal area ) frls, pvc insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main db to sub main db, drawn in to separate concealed medium grade, isi marked, non metallic pvc conduit 15 mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor / ceiling etc as original by brick work, plastering, white washing, obd etc as required, complete all as directed.note : 1. the cost of concealed conduit & accessories is deemed to be included in quoted rates.2. the two run of 4 sqmm wire and one run of 4 sqmm wire will be measured as one unit. 55 all as per srl item no. 54here-in-before but with 2 run of 6.0 sq mm fr copper wire with 6.0 sqmm frls copper cable as earth wire. complete all as specified and directed.note : 1. the cost of concealed conduit & accessories is deemed to be included in quoted rates.2. the two run of 4 sqmm wire and one run of 4 sqmm wire will be measured as one unit. 56 s&f in replacement of db, double door, made out of crca mild steel sheet surface with insulated material like polyester or with epoxy powder coating and ip 43 & ik 09 protection, spn 12 way, 240 volts with bush bar rating 200 amps, dust and vermin proof, suitable for incorporation of mcb’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed. 57 s&f in replacement of db, double door, made out of crca mild steel sheet surface with insulated material like polyester or with epoxy powder coating and ip 43 & ik 09 protection, spn 4 way, 240 volts with bush bar rating 200 amps, dust and vermin proof, suitable for incorporation of mcb’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed. 58 s&f in replacement of mcb, c curve type, 10 ka, 40 to 63 amp, spn with over load and short circuit protection, complete all as specified and directed. 59 s&f in replacement of mcb, c curve type, 10 ka, 6 to 40 amp, single pole with over load and short circuit protection, complete all as specified and directed. 60 m&l for earthing with galvanized steel earth plate electrode of size 600 x 600 x 6 mm buried directly in ground earth pit not less than 2.25 mtr below of normal ground level with top edge of earth plate should not less than 1.5 mtr below normal ground level and connected to galvanized iron earth lead wire of size 4 mm dia by means of bolts, nuts, washers of galvanized iron or steel all as shown in electrical plate no.3 of mes ssr part i connecting to earthing test point on completion with and including 15 mm bore gi light grade protection pipe ( 7.5 mtr long ) for earth lead gi lead wire 4mm dia ( 7.5 mtr long ) , pcc pit with cover in pcc 1:2:4 type b-1 reinforced with 8 mm dia tor bars @ 80mm c / c, 20mm dia medium grade watering pipe with funnel, wire mesh, common salt, charcoal, necessary excavation and earth work, complete all as specified and directed. 61 schedule of credit