bill of quantities for special maintenance and repair of type v / 8 and sports clubat 220 k.v. substation sikandra, agra- concrete with 4cm gaugestone ballast, coarse sand ( f.m. 1.8 to 2.5 ) & cement in proportion of 12:6:1 in foundations &under floors including supply of all materials, labour and tools and plants etc. required for proper completion. ( csi no. 5.02 ) 2 cement concrete with 2cm gauge approved hard stone ballast, coarse sand ( f.m. 1.8 to 2.5 ) and cement in proportion of 4:2:1including supply of all materials, labour, side shuttering ifrequired and t&p etc. required for proper completion of work. ( csi no. 5.06 ) 3 rcc work with cement, approved coarse sand ( f.m. 1.8 to 2.5 ) and2 cm gauge graded approved hard stone ballast like granite, quartzite etc from dalla, jhansi or other quarries in proportion 1:1.5:3in lintels of doors and windows, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and t&p. . ( csi no.5.23 ) 4 first class brick work in 1:6 cement and coarse sand ( f.m.1.8 to 2.5 ) mortar in foundation and plinth including supply of allmaterials, labour & t&p etc. required for proper completion of work. ( csi no. 6.01 ) 5 as in item 4 above but for walls of one brick thickness.add for extra labour to the rates of item no.6.07. ( csi no.6.01+ 6.08 ) 6 mild steel or iron work in heavy sizes such as trusses built upgates, door frames, record, racks roof work gates etc. wrought torequired form including holes rivetting or welding where necessary and also fixing in proper position and alignment including cost of all materials supplied by contractor. ( csi no. 9.01 ) 7 mild steel or iron in plain / torwork in plain work such as r.c.c. or r.b. work ( when not included in over all rates ) wrought to required shape as necessary includingbending as per requirement and direction of e / ifor proper completion of the work and including supply of steel, its wastage, bend, hook and authorised overlapping in reinforcement shall be measured. ( steel shall be arranged by the contractor ) ( csi. no. 9.03 ) 8 supply and fixing galvanised mosquito proof jali ( 16x24 gauge ) withm.s. flat of 20 x 3 mm. size, on both sides screwed or welded to windowor door frame. ( csi no. 9.18 ) 9 12 mm thick plaster with cement mortar consisting of one part of cement & four part of coarse sand ( 1:4 ) , minimum thickness not to be less then 10 mm including supply of all material, labour and t&p etc for proper completion of work. ( csi no. 11.07 ) 10 12 mm thick plaster with cement mortar consisting of one part of cement & six part of coarse sand ( 1:6 ) , minimum thickness not to be less then 10 mm including supply of all material, labour and t&p etc for proper completion of work. ( csi no. 11.09 ) 11 add for extra labour and materials for plaster over rough face ofone brick thick wall. ( csi no. 11.12 ) 12 2 cm. thick cement plaster in dado or skirting in 1:2 consisting of onepart of cement and two parts of approved coarse sand laid inpanels finished with 3mm.floating coat of neat cement or cementand marble dust in ratio of 5:1 including supply of all materials, labour & t&p etc. required for proper completion of the work. ( csi no.11.13 ) 13 s / mixing approved water proofing compound ( cico, dr fixit etc ) in cementmortar in plaster or concrete work in the proportion as recommended by the manufacturer. ( csi no. 11.15 ) 14 making drip coarse ( 25x12 ) mm in 1:2 cement and coarse sandincluding supply of all materials, labour and t&p etc requiredfor proper completion of work. ( csi no. 11.19 ) 15 4.0 cm thick 1:2:4 plain cement concrete floor with cement, approved coarse sand & 2cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and removing any overlapping mortar at the joints of the panels if any and giving them a uniform finish including supply of all materials, labour and t&p etc, required for proper completion of the work. without base cc ( csi no. 12.04 ) 16 providing and laying floor of 8 mm thick vitrifiedtiles in flooring or skirting of approved brand ( bell, johnson or equi. make ) size of 600x600 mmof approved shade, colour and pattern , laid over base cement mortar 1:4 mix including finishing the joints with white cementmixed with pigment to match the shade of tile including cost of all material, labour and t&p required for proper completion of the work. ( csi no. 12.18 ) 17 supply and laying 8 mm thickglazed floor tiles of somany, johnson or equivalent make, , laid with1:3 cement and approved coarse sand mortar finished with whitecement slurry, jointing and polishing complete, including supplyof all materials, labour and t&p etc. required for proper completion of the work. ( csi no. 12.11 ) 18 painting or varnishing new iron work in small areas or new woodwork with one coat of ready mixed priming paint and one coat ofapproved superior quality ready mix paint luxol or equivalentbrand or varnish including supply of all materials, labour and t&p etc. required for proper completion of the work. paint to be used should conform to the i.s. 103-1950. ( csi no. 13.01 ) 19 as in item 18 above but every coat after the first coat. ( csi no. 13.02 ) 20 as in item 18 above but for every coat on previously paintedold wood or iron work including its sand papering, rubbing andcleaning as required, for proper completion of work. ( csi no. 13.03 ) 21 removing paint or varnish with paint remover or with caustic soda including supply of all materials, labour and t&p etc. required for proper completion of the work. ( csi no. 13.07 ) 22 one priming coat and one coat oil bound distemper on new work includingsupply of all materials, labour and t&p etc. required for propercompletion of the work. ( csi no. 13.08 ) 23 as in item 22 but for every coat after the first coat. ( csi no. 13.09 ) 24 as in item 22 but for every coat on previously old oil bound distemper surface. ( csi no. 13.10 ) 25 applying birla or equivalent putty on new interior or exterior surface over one coat of water based cement primer of ici or equivalent brand for smoothening and levelling of the surface as per requirement and direction of engineer i / c including cost of all material, labour, t & p etc required for proper completion of work. ( csi no. 13.20 ) 26 applying birla putty or equivalent putty on previousaly bila putty smoothen surface over one cost of water base cement primer of ici or equivalent brand for smoothining and leveling of the surface as per requirement and direction of e / i including cost of all material , labour and t&p required for proper completion of work. ( csi no.13.21 ) 27 providing and laying water proofing treatment in sunken portion of wcs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : ( a ) first layer of slurry of cement @ 0.488 kg / sqm mixed with water proofing cement compound @ 0.253 kg / sqm. this layer will be allowed to air cure for 4 hours. ( b ) second layer of slurry of cement @ 0.242 kg / sqm mixed with water proofing cement compound @ 0.126 kg / sqm. this layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. the rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. ( csi no. 28.26 ) 28 finishing walls with water proof exterior emulsion paint oface ( asian ) or equivalent brand on already well prepared new wall surfaces with one coat of primer ( ici ) followed by two coats of ace exterior empulsion paint to give an even shade including thorough washing with water including as per direction of e / i direction of including cost of all materials, labour, t&p etc requried for proper completion of the work ( nsi ) 29 finishing walls with water proof exterior emulsion paint oface ( asian ) or equivalent brand on old surfaces to give an even shade including thorough washing with water including as per direction of e / i direction of including cost of all materials, labour, t&p etc requried for proper completion of the work ( nsi ) 30 dismantling brick work or stone work in lime or cement mortar andincluding stacking of materials as directed by theengineer-in-charge within a distance of 60 metres. ( csi no. 15.01 ) 31 dismantling reinforced cement concrete or reinforced brick work, including stacking of dismantled materials as directed by theengineer-incharge within a distance of 60 metres. ( csi no. 15.03 ) 32 dismantling of griders, trusses and other steel works including stcking of materials as directed by engg-in-charge within a distance of 60 mtrs. ( csi no. 15.08 ) 33 dismantaling doors and windowschowkhatsincluding stacking of materials as directed by engg-in-charge within a distance of 60 meters. ( csi no. 15.10 ) 34 dismantling existing plaster including disposal of refuse asdirected by the engineer-i / c within a distance of 60 m. ( csi no. 15.11 ) 35 renewing panes of 4 mm glass including supply of glass with putty and brads including supply of all materials, labour and t&p etc. required for proper completion of the work. ( b ) same as above itembut 4 mm thick panes. ( csi no. 20.04i ) ( 806b ) 36 disposal of rubbish / debris out side the uppcl area as per direction of er / in- charge including cartage, labour and materials, t&p etc. required for proper completion of the work. ( no. deduction for voids shall be made ) . ( csi no. 20.16 ) 37 supply and replacing of following chromium polished iron fittings including cost of nuts, bolts etc.complete. ( a ) l drops 16 mm dia x 300 long. ( csi no. 20.17a ) 38 ( c ) tower bolts 10 mm dia x 100 mm long. 39 ( d ) iron hinges 100 mm size.12 gauge.thick 40 ( e ) iron door spring. 41 ( f ) m.s.handles 100 mm size 42 s / laying chicken mesh of ( 20 mm. ) hexagonal heavy quality over roofs of joints of roof as per direction of the engineer - in - charge. ( csi no. 20.21 ) 43 providing and fixing pvc ball float valve 25 mm dia. with brass & union complete, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. ( csi no. 26.06 c ) 44 providing and fixing non return reflex valve, 20 mm dia isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. ( csi no. 26.07 b ) 45 providing and fixing non return reflex valve, 25 mm dia isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. ( csi no. 26.07 c ) 46 providing and fixing pvc connection pipe, 300x15 with 2 brass units isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. ( csi no. 26.09 ) b 47 p / f gi unions nominal bore 25 mm, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. ( csi no. 26.10 c ) 48 p / f gi unions nominal bore 20 mm, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. ( csi no. 26.10 b ) 49 supply and fixing of syntex or equivalent make water storage tank including all materials, labours, t&p etc required for proper completion of work. ( csi no. 26.12 ) 50 providing and fixing cp brass bib cock15 mm dia. heavy quality ( 200gm ) ( l & k and equi. ) fittings, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. ( csi no. 26.16 b ) 51 providing and fixing of 110 mm dia pvc pipe 6 kg / sq.cm forwith special such as tee, bend, socket, elbow etc including supply of all labour, material, t & p etc complete required for proper completion of work. ( csi no. 26.17 ) 52 p / f 32 mm dia c.p. waste jali with cheknut complete. ( s.no. 25.29 ) 53 p / f 25 m.m dia upvc pipe complete with upvc special such as bends, tee, socket, cross, clamp etcrequired for proper completion of the work the rate also including upvc fitting where required cutting and making good the wall etc and all materials labour t&p etc complete ( nsi ) 54 p / f 20 m.m dia cpvc pipe complete with cpvc special such as bends, tee, socket, cross, clamp etcrequired for proper completion of the work the rate also including cpvc fitting where required cutting and making good the wall etc and all materials labour t&p etc complete ( nsi ) 55 p / f 15 m.m dia cpvc pipe complete with cpvc special such as bends, tee, socket, cross, clamp etcrequired for proper completion of the work the rate also including cpvc fitting where required cutting and making good the wall etc and all materials labour t&p etc complete ( nsi )