supply, testing , installation & commissioning of instruments, shop outfit, equipment, machinery, etc.for the trade of fitter- 1 fitter : 2 pneumatic trainer kit, each consisting of the following matching components and accessories:compressor unit, suitable for pressure: 8 bar, delivery: 50 lpm ( or more ) , reservoir capacity: 24 litres ( or more ) , 230v, 50 hz, with pressure regulator and water separator- 1 no.i. single acting cylinder, max. stroke length 50 mm, bore dia. 20 mm - 1 no. ii. double acting cylinder, max. stroke length 100 mm, bore dia 20 mm, magnetic type - 1 no. iii. 3 / 2-way valve, manually-actuated, normally closed - 2 nos. iv.3 / 2-way valve, pneumatically-actuated, spring return-1 no. v. one-way flow control valve - 2 nos. vi. 5 / 2-way valve, with manually-operated switch- 1 no. vii. 5 / 2-way valve, pneumatically-actuated, spring return- 1 no. viii. 5 / 2-way pneumatic actuated valve, double pilot - 1 no. ix. 3 / 2-way roller lever valve, direct actuation normally closed- 2 nos. x. shuttle valve ( or ) - 1 no. xi. two-pressure valve ( and ) - 1 no. xii. pressure gauge, 0-16 bar - 1 no. xiii. manifold with self-closing, nrv, 6-way - 1 no. xiv. pushbutton station for electrical signal input, with 3 illuminated momentary-contact switches ( 1 no + 1 nc ) and 1 illuminated maintainedcontact switch ( 1 no + 1 nc ) , contact load 2a - 1 no. xv. relay station, with 3 relays each with 4 contact sets ( 3no+1nc or change-over type ) , 5 a - 1 no. xvi. 3 / 2-way single solenoid valve, with led - 1 no. xvii. 5 / 2-way single solenoid valve, with manual override and led - 1 no. xviii. 5 / 2-way double solenoid valve, with manual override and led - 1 no. xix. power supply unit, input voltage 85 – 265 v ac, output voltage: 24 v dc, output current: max. 4.5 a, short-circuit-proof.- 1 no. xx.pneumatic workstation ( to be fitted onto the pneumatic workstation ) with profile plate, anodised aluminium, 1100x700 mm, with carriers, mounting frames and mounting accessories - 1no.--- 40 mm aluminium profile legs, wooden square work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: ( 1 ) worktable – size ( approx. ) l1200mmxw900mmxh900 mm, with four castor wheels including two lockablewheels at the front side, ( 2 ) drawer – size ( approx. ) – l460mmxw495mmxh158mm each, and overall size of drawer unit ( approx. ) l470mmxw495mmxh825mm and ( 3 ) drawer slide height ( approx ) 85mm. - 1 no. carrier for mounting components, as pb & relay boxes.such - 1 no. cut section model for pneumatic components - 1 set. n.b :- all valves / components are properly mounted on work station and by suitable piping / cables with quick release coupling ( qrc ) . end fittings to construct various type of circuit. installation, demonstrations and commissioning must be satisfactory. 3 hydraulic trainer kit, each consisting of the following matching components and accessories:i. hydraulic power pack with, ( 1 ) external gear pump having a delivery rate of 2.5 lpm, ( approx. ) @ 1400 rpm operating pressure 60 bar, coupled to a single-phase ac motor ( 230 v ac ) having start capacitor and on / off switch and overloadprotection, ( 2 ) pressure relief valve adjustable from 0 – 60 bar, ( 3 ) oil reservoir, ≥5 litres capacity having sight glass, drain screw, air filter, and p and t ports. - 1 no. ii. pressure relief valve, pilot-operated - 1 no. iii. drip tray, steel, size 1160 mm x 760 mm.- 1 no. iv.pressure gauge, glycerin-damped, indication range of: 0 – 100 bars - 1 no. v. four-way distributor, with five ports, equipped with a pressure gauge - 1 no. vi. double acting hydraulic cylinder, with a control cam, piston diameter16 mm, piston rod diameter10 mm, stroke length 200 mm. - 1 no. vii. suitable weight, for vertical loading of hydraulic cylinder - 1 no. viii. mounting kit for weight, for realizing pulling and pushing load. - 1 no. ix. 3 / 2-way directional control valve, with hand lever actuation - 1 no. x. 4 / 2-way directional control valve, with hand lever actuation - 1 no. xi. 4 / 3-way directional control valve, close centre position with hand lever actuation. - 1 no. xii. non-return valve. - 1 no. xiii. pilot-operated check valve, pilotto open.- 1 no. xiv. one-way flow control valve, withintegrated check valve.- 1 no. xv. t-connector with self-sealing coupling nipples ( 2 nos. ) and quick coupling socket ( 1no. ) - 2 set.xvi.hydraulic workstation ( as set ) with profile plate, ( to be fitted onto the hydraulic workstation ) , anodised aluminium, 1100x700 mm, with carriers, mounting frames and mounting accessories. - 1 no.----40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide:, ( 1 ) worktable – size ( approx. ) l1200mmxw900mmxh900 mm, with four castor wheels including two lockablewheels at the front side, ( 2 ) drawer – size ( approx. ) l460mmxw495mmxh158mm each, and overall size of drawer unit ( approx. ) l470mmxw495 mmxh825mm and ( 3 ) drawer slide height ( approx. ) 85mm. - 1 no. cut-section models for hydraulic components. - 1 set. n.b :- all valves / components are properly mounted on work station and by suitable piping / cables with quick release coupling ( qrc ) . end fittings to construct various type of circuit. installation, demonstrations and commissioning must be satisfactory. 4 slip gauge as johnson metric set. 87 pieces as set 5 gauge set of plug. single ended 5 to 55 by 5 mm. 01 set of 11 pcs. 6 gauge telescopic set. 8 - 150 mm 7 digital verniercaliper. 0 - 150 mm with least count 0.02mm 8 digital verniercaliper.0 - 200 mm l.c. 0.01 mm ( optional ) 9 digital micrometer outside. 0 - 25 mm l.c. 0.001 mm. 10 surface roughness comparison plates. n1 - n12 grade ( as a set )