repair and maintenance work of staff quarter type-iii (59 nos), type-ii (85 nos) and type-i (18 nos) in sector eta-i, greater noida repair and maintenance work of staff quarter type-iii (59 nos), type-ii (85 nos) and type-i (18 nos) in sector eta-i, greater noida , repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead: , with cement mortar 1:4 (1 cement : 4 coarse sand) (dsr-13/14.1.2/p-237) , providing and fixing isi marked flush door shutters conforming to is: 2202 (part-i) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. , 30 mm thick including isi marked stainless steel butt hingeswith necessary screws: (dsr-13/9.20.2/p-150) , providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). , sal wood. (dsr-13/9.1.2/p-147) , fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for hold fasts, embedding hold fasts in cement concrete blocks in size 15x10x10cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground within 50 meters lead: , door chowkhats (dsr-13/14.2.1/p-237) , providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes, including isi marked m.s. pressed butt hinges bright finished of required size with necessary screws. , kiln seasoned and chemically treated hollock wood. 30mm thick(dsr-13/9.9.2.2/p-149) , providing and fixing wire gauge shutters using galvanised m.s. wire gauge of average width of aperture 1.4mm in both directions with wire of dia 0.63 mm for doors, windows and clerestory windows with hinges and necessary screws: , 30mm thick shutters - with isi marked m.s. pressed butt hinges bright finished of required size. kiln seasoned and chemically treated hollock wood (dsr-13/9.27.2.1.2/p-151) , providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete: , 2nd class teak wood. 50x12mm (dsr-13/9.40.1.1/p-153) , kota stone slab flooring over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of 1:4 cement mortar 1:4 (1 cement : 4 coarse sand). , 25mm thick. (dsr-13/11.26.1/p-190) , marble stone flooring with 18mm thick marble stone, as per sample of marbleapproved by engineer-in-charge, over 20mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with: , raj nagar plain (dsr-13/11.23.2/p-189) , precast terrazzo tiles 22mm thick with graded marble chips of size upto 12mm, laid in floors, and landings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand): , ordinary cement without any pigment (dsr-13/11.16.4/p-188) , providing and fixing 18mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels. , granite of any colour and shade. area of slab upto 0.50 sqm. (dsr-13/8.2.2.1/p-128) , renewing glass panes, with wooden fillets wherever necessary: , float glass panes of thickness 4mm. (dsr-13/14.6.1/p-237) , providing and fixing aluminium sliding door bolts, isi marked anodised (anodic coating not less than grade ac 10 as per is: 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete: , 300x16mm (dsr-13/9.96.1/p-159) , 250x16mm (dsr-13/9.96.2/p-159) , providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: , 300x10mm (dsr-13/9.97.1/p-159) , 200x10mm (dsr-13/9.97.3/p-159) , 150x10mm (dsr-13/9.97.4/p-159) , providing and fixing aluminium handles,isi marked, anodised (anodic coating not less than grade ac 10 as per is: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: , 125 mm (dsr-13/9.100.1/p-160) , 100 mm (dsr-13/9.100.2/p-160) , providing and fixing aluminium hanging floor door stopper, isi marked, anodised (anodic coating not less than grade ac 10 as per is: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. , single rubber stopper (dsr-13/9.101.1/p-160) , providing and fixing aluminium casement stays, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. (dsr-13/9.102/p-160) , providing and fixing hand rail by welding etc. to steel ladder railing, balcony railing, staircase railingand similar works, including applying a priming coat of approved steel primer. , m.s. tube (dsr-13/10.26.1/p-180) , providing and fixing 1st quality ceramic glazed wall tiles conforming to is : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, inskirting, risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (dsr-13/11.36/p-191) , providing and laying ceramic glazed floor tiles of size 300x300mm (thickness to be specified by the manufacturer) of 1st quality conforming to is: 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including pointing the joints with white cement and matching pigment etc., complete. (dsr-13/11.37/p-191) , providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - all work upto plinth level: (cast-in-situ) , 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size). (dsr-13/4.1.8/p-85) , providing and fixing water closet squatting pan (indian type w.c. pan) with 100mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to is: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: , white vitreous china orissa pattern w.c. pan of size 580x440mm with integral type foot rests. (dsr-13/17.1.1/p-287) , providing and fixing white vitreous china pedestal type water closet (european type w.c. pan) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming tois : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: , w.c. pan with isi marked white solid(dsr-13/17.2.1/p-287) , providing and fixing wash basin with c.i. brackets, 15mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: , white vitreous china wash basin size 630x450 mm with a pair of 15mm c.p. brass pillar taps. (dsr-13/17.7.1/p-288) , providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing: , oval shape 450x350mm (outer dimensions). (dsr-13/17.32.3/p-291) , providing and fixing pvc waste pipe for sink or wash basin including pvc waste fittings complete. , flexible pipe: 32mm dia. (dsr-13/17.28.2.1/p-291) , providing and fixing ball valve (brass) of approved quality, high or low pressure, with plastic floats complete: , 25 mm nominal bore (dsr-13/18.18.3/p-321) , providing and fixing unplasticised pvc connection pipe with brass unions: , 45 cm length: 15 mm nominal bore (dsr-13/18.21.2.1/p-322) , providing and fixing c.p. brass shower rose with 15 or 20mm inlet: , 100 mm diameter (dsr-13/18.22.1/p-322) , providing and placing on terrace (at all floor levels) polythylene water storage tank, isi : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. (dsr-13/18.48/p-327) , providing and fixing c.p. brass bib cock of approved quality conforming to is: 8931: 15mm nominal bore (dsr-13/18.49.1/p-327) , providing and fixing c.p. brass long nose bib cock of approved quality conforming to is standards and weighing not less than 810 gms. 15mm nominal bore (dsr-13/18.50.1/p-328) , providing and fixing c.p. brass stop cock (concealed) of standard design and of approved make conforming to is: 8931: 15mm nominal bore (dsr-13/18.52.1/p-328) , providing and fixing 3 layer pp-r (poly propylene random copolymer) pipes sdr 7.4, uv stabilized and anti- microbial fusion welded, having thermal stability for hot & cold water supply, including all pp-r plain & brass threaded polypropylene random fittings, including fixing the pipe with clamps at 1.00m spacing. this includes the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer-in-charge. concealed work, including cutting chases and making good the walls. etc.: , pn - 16 pipe,20 mm od (dsr-13/18.5.2/p-318) , providing and fixing 3 layer pp-r (poly propylene random copolymer) pipes, u v stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all pp-r plain & brass threaded polypropylene random fittings including trenching, refilling & testing of joints complete as per direction of engineer in charge. external work: , pn - 16 pipe, 20 mm od (sdr-7.4) (dsr-13/18.6.2/p-318) , providing, laying, jointing and testing of pvc pipe (finolex make ring fit) of following dia 6kg/cm2 including all specials & fittings etc. as required for proper completion of work (the contractor has to arrange the source of water and require head for testing). (ar/gnida) , 110 mm dia (o.d.) , 90 mm dia (o.d.) , providing and fixing rigid pvc nahani trap of self cleaning design with complete including costof cutting and making good the walls and floors(a.r./gnida) , 110mm inlet and 110mm outlet. , 110mm inlet and 90mm outlet. , providing and fixing stainless steel jali (grating) with or without hole for waste pipe for nahani trap. (a.r./gnida) , providing and fixing brass gate valve with ci wheel of approved quality (screwed end)(a.r./gnida) , 15mm nominal bore , 20mm nominal bore , supplying and fixing c.i. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5kg. (dsr-13/19.20/p-354) , supplying and fixing c.i. cover without frame for manholes: , 455x610mm rectangular c.i. cover (light duty) the weight of the cover to be not less than 23 kg. (dsr-13/19.18.1/p-354) , providing and fixing g.i. union in g.i. pipe including cutting and threading the pipe and making long screws etc. complete (new work). , 20 mm nominal bore (dsr-13/18.46.2/p-327) , providing and fixing c.p. brass angle valve for basin mixer and geyser points of approved quality conforming to is: 8931 : 15mm nominal bore (dsr-13/18.53.1/p-328) , providing and fixing p.v.c. low level flushing cistern with manually controlled device (handle lever) conforming to is: 7231, with all fittings and fixtures complete. , 10 litre capacity - white (dsr-13/17.18.1/p-290) , providing and fixing solid plastic seat with lid for pedestal type w.c. pan complete: , white solid plastic seat with lid. (dsr-13/17.20.1/p-290) , providing and fixing on wall face unplasticised - pvc moulded fittings/accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is: 5382, leaving 10mm gap for thermal expansion. , coupler: 110 mm (dsr-13/12.42.1.2/p-209) , single tee with door: 110x110x110 mm (dsr-13/12.42.3.2/p-209) , single tee without door: 110x110x110 mm (dsr-13/12.42.4.2/p-209) , bend 87.50 : 110 mm bend (dsr-13/12.42.5.2/p-209) , constructing masonry chamber 60x60x75 cm. inside, in bricks work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with c.i. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and rcc top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size), i/c necessary excavation,foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design: , with bricks of class designation-150 (dsr-13/18.33.1/p-324) , providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with c.p. brass screws and wooden plugs etc., wherever necessary complete: , 20 mm dia (dsr-13/9.46.2/p-154) , steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. , in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works (dsr-13/10.25.2/p-180) , providing and fixing isi marked oxidised m.s. pressed butt hinges with necessary screws etc. complete. , 125x65x2.12 mm (dsr-13/9.57.1/p-155) , providing and fixing bright finished brass night latch of approved quality including necessary screws etc. complete. (dsr-13/9.78/p-157) , providing & fixing fly proof wire gauze to windows, clerestory windows & doors with m.s. flat 15x3mm and nuts & bolts complete. , stainless steel (grade 304) wire gauze of 0.5mm dia wire and 1.4mm aperture on both sides. (dsr-13/10.29.2/p-180) , making cornish with p.o.p. at the junction of slab & wall including supply of all material, labour, t&p etc. complete as per directed byengineer-in-charge. (a.r/gnida) , making moulding with p.o.p. on ceiling including supply of all material, labour, t&p etc. complete as per directed byengineer-in-charge. (a.r/gnida) , making gola with p.o.p.around the fan and light point on ceiling including supply of all material, labour, t&p etc. complete as per directed byengineer-in-charge. (a.r/gnida) , 60cm dia (fan) , providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. (dsr-13/13.26/p-224) , distempering with oil bound washable distemper of approved brand and manufacture to given an even shade: old work (one or more coats) (dsr-13/14.45.1/p-241) , removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. (dsr-13/14.46/p-241) , finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade. , old work (two or more coats applied @ 1.43 ltr./10sqm) over existing cement paint surface. (dsr-13/14.67.1/p-243) , providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (dsr-13/13.80/p-229) , painting with synthetic enamel paint of approved brand and manufacture of requiredcolour to give an even shade: one or more coats on old work. (dsr-13/14.54.1/p-242) , supply of labour (ar/gnida) , supplying chemical emulsion in sealed containers including delivery as specified. chlorpyriphos/lindane emulsifiableconcentrate of 20%. (dsr-13/2.34.1/p-76) , diluting and injecting chemical emulsion for post-constructional anti- termite treatment (excluding the cost of chemical emulsion): , along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litre per linear metre including drilling and plugging holes etc. with chlorphyriphos/lindane e.c. 20% with 1% concentration. (dsr-13/2.35.2.1/p-76) , add labour cess @ 1% on all above items