bids are invited for facility management services - lumpsum based - as per atc; remodelling of r d first floor to develop project office at msb concentrator plant; consumables to be provided by service provider (inclusive in contract cost) - providing and fixing false ceiling with 12 mm thick plain/ semi perforated or with design ceiling tiles of bwp type phenol formaldehyde synthetic resin bonded pressed particle board conforming to is:3087 finished with a coat of aluminum pr , providing and fixing at all height false ceiling including providing and fixing of frame work made of special sections power pressed from m.s. sheet and galvanised in accordance with zinc coating of grade 350 as per is : 277 and consist , providing and fixing stainless steel a isi 304 (18/8) kitchen sink as per is 13983 with c.i. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required: 460x915 , wall painting with acrylic emulsion paint of approved brand , providing and fixing telephone shower , providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with c.p. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete , providing and fixing ply board of 6 mm thick with necessary screw, nails etc on existing false ceiling. , providing and fixing of 1st quality sunmica on top and vertical portion of the table including providing & fixing plywood, wooden bids polishing all complete. the rate are inclusive of all the materials & manpower. , varnishing with varnish of approved brand and manufacture: two or more coats of glue sizing with copal varnish over an under coat of flatting varnish , providing and laying 32mmid hdpe pipe of screwed ends connected through sockets including providing sealant compound in joints â all complete , providing and fixing isi marked steel glazed doors, windows and ventilators of standard rolled steel sections, joints mitred and welded with 15x3mm lugs, 10cm long embedded in cement concrete blocks 15x10x10cm of 1:3:6 (1 cement: 3 coarse s , providing and fixing factory made panel pvc door shutter consisting of frame made out of m.s. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles , providing and fixing 25 m.m. thick shutters for cupboard second class teak wood including isi marked anodised aluminioum but hinges with necessary screws , providing and fixing flush door shutters non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial ply veneering with vertical grains or cross bands and face veneers on both faces o , providing and fixing p.v.c. low level flushing cistern with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete.10 litre capacity – white , providing and fixing p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete.semi rigid pipe32 mm dia , providing and fixing uplasticised pvc connection pipe with brass unions :30 cm length15 mm nominal bore , providing and fixing g.i. pipes complete with g.i. fittings includingtrenching and refilling etc. external work20 mm dia. nominal bore , providing and fixing oxidised m.s. tower bolt (barrel type) with necessary screws etc. complete: 150*10 mm. , providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and c.p. b , providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 100 mm outlet sand cast iron , structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete: , 15 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement: 4 fine sand) , brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level up to floor v level in all shapes and sizes in :cement mortar 1:6 (1 cement : 6 coarse sand) , neat cement punning , providing and fixing oxidised m.s. sliding door bolts with nuts and screws etc. complete. , 12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand) , painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :one or more coats on old work. , centering and shuttering including strutting, propping etc. and removal of form for : suspended floors, roofs, landings, balconies and access platform , providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. , providing and fixing g.i. pipes complete with g.i. fittings including trenching and refilling etc. external work15 mm dia. nominal bore , providing and fixing brass bib cock of approved quality :15 mm nominal bore , providing and fixing brass stop cock of approved quality :15 mm nominal bore , half brick masonry with f.p.s. bricks of class designation 7.5 in super structure above plinth level up to floor v level. cement mortar 1:4 (1 cement : 4 coarse sand) , providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position : sal wood , renewing glass panes with putty and nails wherever necessary as per direction of engineer-in-charge. glass panes weighing 13.75 kg/sq.m (4mm thick) , chipping & removing plaster from old wall or floor surface at all heights and places, scraping and clean the surface and disposing off the debris within lead of 2 k.m. , providing and laying pcc 1 : 2:4 etc. complete as per direction of engineer incharge , excavation in foundation tranches in all kinds of soils including soil mixed gravel, slag, boulders etc. up to a depth of 2 m include watering wherever required back filling the trenches with good quality soil in 150mm layers, watering and , dismantling or cutting openings in r.c.c. or other high grade concrete structures, and disposing off the debris as directed within a lead of 2 km. , providing and fixing isi marked oxidised m.s. handles conforming to is:4992 with necessary screws etc. complete : 125 mm , providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and