providing infrastructure requirement in mro office musheerabad v)(m) in hyderabad district - repairs to existing building:- earth work excavation and depositing on bank (manual means) with initial lead of 10m and initial lift of 3m in loamy & clayey soils like bc soils, red earth & ordinary gravelly soils ( ss 20-b) including all operational incidental labour charges such as shoring, strutting, sheeting, planking and dewatering including cost of hire charges of t & p, labour charges etc., complete for finished item of work excluding seignerage charges and dewatering charges etc., complete for foundation of building.(apss no. 308) plain cement concrete corresponding to m5 grade as per is 456 equivalent to (1:5:10) proportion nominal mix (cement: fine aggregate: coarse aggregate) using natural river sand,40mm size hard blasted granite (is383, 1970) metal from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, including sales & other taxes on all materials, all operational, incidental, and labour charges such as mixing, laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete but excluding seigniorage chargesfor finished item of work for foundations and flooring bed (apss no. 402) plain cement concrete m20 design mix ( by weigh batching ) using and natural river sand, 20mm size (ss5) hard blasted trap machine crushed graded metal (coarse aggregate) from approved quarry, using a minimum quantity of 350 kgs. of cement per 1 cum of concrete including cost and conveyance of all materials like cement, fine aggregate (sand), coarse aggregate, water etc., to site and cost of all materials including steel centering, shuttering, machine mixing, laying concrete, lift charges, curing etc., complete but excluding seigniorage charges for finished item of work for steps in - situ - granolithic concrete flooring 20mm thick with cc(1:1:2) prop: using 6mm to 12mm size hbg machine crushed metal laid monolithically over existing cc flooring bed in alternate panels of size not exceeding 1.50m x 1.50m and finishing the top surface to required smoothness and slopes, thread lining as directed by the engineer - in - charge including cost and conveyance of all materials like cement, sand, water, etc. to site, seigniorage charges, sales and other taxes on all materials, all operational, incidental and labour charges such as mixing of cement concrete, laying, curing, lift charges etc., complete for finished item of work (apss no.701 & 710) dadooing to walls with white glazed tiles 1st. quality of any size of brand as approved by engineer - in - charge and set over a base coat of cm (1:5) using screened sand, 12mm thick and neat cement paste at the rate of 3.3 kg/sqmt. and jointed with white cement paste mixed with pigment of matching shade including cost and conveyance of all materials like cement, sand, water, tiles, etc. to site, sales and other taxes on all materials, c921 such as mixing of cement mortar, laying in position, curing, lift charges etc., complete but excluding seigniorage charges for finished item of work (apss no.701 & 707) in all floors flooring with ceramic tiles of 7.3mm thick 1st. quality of non-skid red or white full body ceramic floor tiles of size not less than 300 x 300 mm and thickness between 7-8 size as approved by engineer - in - charge set over a base coat of cm (1:8), 12mm thick laid over flooring bed / v.r.c.c. slab, with neat cement slurry of honey like consistency spread at the rate of 3.3 kgs of cement per sq.m and jointed with neat white cement paste to full depth mixed with pigment of matching shade including cost and conveyance of all materials like cement, sand, water, ceramic tiles etc. to site, sales and other taxes on all materials, all operational, incidental and labour charges such as mixing of cement mortar, laying, curing, lift charges etc., complete but excluding seigniorage charges for finished item of work.(apss no.701 & 707) providing & fixing of open able windows with fly-mesh made of pre-painted steel as per is 513 of 0.58 mm thick galvanized as per is 277 finish painted with a polyester paint and the section for outer frame of 72 x 55mm, centre mullion of 72 x 50mm, section for fixed glass beading section of 12 x 12 mm and section for shutters of 48 x 25 mm and outer frame & mullion sections with rebate for glazed shutters, fly mesh and a 20 mm provision for guard bars/grills and fly mesh shutter section of 20 x 40 mm, stay, handles, latch 2 nos of heavy duty stainless steel pivot hinges per shutter and panelled with 0.5 mm thick galvalume corrugated sheet and s.s. mesh for fly mesh shutter (304 grade), fitted using rubber gaskets including fixing the windows in the concrete/masonry wall by means of self expanding screws, including 10mm square guard bars with 6” (152.4mm) pitch , complete for centre fixed both side open able shutter window for a size 5’0”x4’0” (1524mm x1219.2mm). brick masonry in superstructure with cm (1:8) prop: using fly ash bricks of size 290x225x140mm with compressive of 50 kgs / sqcm from approved source including cost and conveyance of all materials like cement, sand, fly ash bricks, water etc., to site, including sales & other taxes on all materials, all operational, incidental and labour charges such as mixing cement mortar, constructing masonry, scaffolding charges, lift charges, curing, etc., complete but excluding seigniorage charges for finished item of work. (apss no. 501 & 504). plastering 12mm thick in two coats with base coat of 8mm thick in cm (1:6) and top coat of 4mm thick in cm (1:4) dubara sponge finish including cost and conveyance of all materials like cement, sand, water etc., to site, sales & other taxes on all materials,all operational, incidental and labour charges such as mixing mortar, scaffolding charges, lift charges, including cutting of grooves wherever necessary as directed by engineer - in - charge, finishing, curing, etc., complete but excluding seigniorage charges for even surfaces of wall for finished item of work. (apss 901,903 & 904) providing impervious coat with required slopes in cm (1:3) prop. 20mm thick (average) mixed with water proofing compound manufactured by reputed manufacturers as approved by engineer-in-charge at 1kg/bag of cement, laid over roof slab when it is green, finished smooth with a floating coat of neat cement and thread lining at regular intervals of 45cmx45cm including cost and conveyance of all materials like cement, sand, water proofing compound, water etc., to site, sales & other taxes on all materials, all operational, incidental and labour charges such as mixing mortar, laying, rounding off at junctions of wall and slab, rendering smooth with thread lining, curing, lift charges, etc., complete but excluding seigniorage charges for finished item of work (apss no. 901 & 903). painting to new walls with two coats of acrylic emulsion paint of superior quality of approved brand and shade over base coat of cement primer interior grade -i making three coats in all to give an even shade after thoroughly brushing the surface to remove all loose powdered materials, including cost and conveyance of all materials, including cost and conveyance of all materials, cost of brushes, water to site, etc., sales & other taxes, all operational, incidental and labour charges such as scaffolding charges, lift charges, curing etc., complete for finished item of work in all floors for internal walls.(apss no. 912) in all floors painting to new walls with two coats of acrylic emulsion paint of superior quality of approved brand and shade over base coat of cement primer exterior grade -ii making three coats in all to give an even shade after thoroughly brushing the surface to remove all loose powdered materials, including cost and conveyance of all materials, including cost and conveyance of all materials, cost of brushes, water to site, etc., sales & other taxes, all operational, incidental and labour charges such as scaffolding charges, lift charges, curing etc., complete for finished item of work in all floors for external walls.(apss no. 912) in all floors painting to iron work with two coats of ready mixed synthetic enamel paint first quality all shades over an existing steel primer including cost and conveyance of all materials to site, sales & other taxes, incidental, operational and all labour charges etc., complete for finished item of work. (apss no. 1201, 1207 & 1212).in all floors painting to new wood work with two coats of ready mixed synthetic enamel paint grade i all shades to give an even shade over base coat primer with luppam finishing after thoroughly brushing the surface to remove all remains including cost and conveyance of all materials to site, sales & other taxes, all operational, incidental and labour charges etc., complete for finished item of work.(3 coats) (apss no. 1201 & 1212).in all floors first floor:- plain cement concrete m20 design mix ( by weigh batching ) using and natural river sand, 20mm size (ss5) hard blasted trap machine crushed graded metal (coarse aggregate) from approved quarry, using a minimum quantity of 350 kgs. of cement per 1 cum of concrete including cost and conveyance of all materials like cement, fine aggregate (sand), coarse aggregate, water etc., to site and cost of all materials including steel centering, shuttering, machine mixing, laying concrete, lift charges, curing etc., complete but excluding seigniorage charges for finished item of work for steps flooring with ceramic tiles of 7.3mm thick 1st. quality of non-skid red or white full body ceramic floor tiles of size not less than 300 x 300 mm and thickness between 7-8 size as approved by engineer - in - charge set over a base coat of cm (1:8), 12mm thick laid over flooring bed / v.r.c.c. slab, with neat cement slurry of honey like consistency spread at the rate of 3.3 kgs of cement per sq.m and jointed with neat white cement paste to full depth mixed with pigment of matching shade including cost and conveyance of all materials like cement, sand, water, ceramic tiles etc. to site, sales and other taxes on all materials, all operational, incidental and labour charges such as mixing of cement mortar, laying, curing, lift charges etc., complete but excluding seigniorage charges for finished item of work.(apss no.701 & 707) electrification :- wiring with 2 runs of 22/0.3mm (1.5 sq.mm) fire retardant low smoke (frls) / hffr p.v.c. insulated 1100 v grade as per is: 694 / 1990 specification for flexible copper cable (isi mark) in existing pipe with 6a 1 way modular switch, ceiling rose including all labour charges etc., complete for light, bell, fan and exhaust fan points in non-residential buildings makes of wires : finolex / rr kabel / havells / polycab / kei (hffr) /dec (hffr)/ v-guard (hffr). makes of switches : legrand myrius / havells fabio / million mway/ gold medal curve / anchor roma viola / cpl vysma/ vimal / gm four-five / salzar / infinity supply, transportation of energy efficient fan, 1200 mm sweep, aluminium body, consuming 28 w, bee 5 star rated, ceiling fan with brush less direct current(bldc)motor, class of insulation: b, 3 nos blades, 30 cm long down rod, 2 nos canopies, shacklekit, safety rope, copper winding, power factor greater than 0.90, service value (cmmav) greater than 8.5, air delivery minimum 235 cmm, 350 rpm( tolerance as per is:374-2019), thd less than 10%. with remote or compatible to electronic step type regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree c(max), insulation resistance more than 2 mega ohm, suitable for 230v, 50 hz, single phase ac supply, earthing etc., including all standard accessories etc., complete. makes : atomberg (efficio ) / havells / orient supply and transportation of 20w +/- 10%, >/ 2000 lumens, 1200mm length led retro tube light, housing made with aluminum anodised body, wide operating voltage with double side connection, pf≥0.9, surge protection: > 2kv, thd<15%, with inbuilt driver and frosted cover cct: 3000k - 6500k as desired by the department and as per isspecifications, minimum cri≥80,.etc complete with 50,000 burning hours with bis certification. luminaire make: phillips / osram / wipro / crompton / bajaj / havells / jaquar / ib led / panasonic / halonix / hpl / syska / eveready / surya / keselec. led make : philips lumileds / cree / nichia / osram / samsung / lg leds. labour charges for fixing of ceiling fan and regulator including transportation and giving connections with twin core wire etc., complete.makes : finolex / rr kabel / havells / polycab / gm / million / v-guard / gold medal / kundancab / hpl / rpg /nandicab / nakoda / payal / finecab / gemini / vimal /suncab supply and fixing of modular electronic stept type fan regulator hum free step type socket size with ms box, front plate in the existing switch board ( modular type ) makes :makes : legrand arteor / schneider zen celo / honeywell blenge plus / cabtree amare / logus platina. supply and fixing of 6a 3/2 pin modular wall plug socket with shutter and 6a 1 way modular switch control on a common switch board with earth continuity including wire leads, earth connections along with all labour charges etc., complete. makes of switches : legrand myreus/crabtree verona / gold madel curve / million / logusanchor roma viola / great white /cpl/vimal/ gm four-five/hpl/l&t/salzar / stanjo supply and run of 3 of 2.5 sq mm pvc f.r l.s. / hffr p.v.c. insulated flexible copper cable 1100 v grade as per is: 694 / 1990 specifications in the existing conduit pipe for run of mains from main panel board to tpn dbs with pin type lugs and connection. makes of wires : finolex / rr kabel / havells / polycab / kei (hffr) /dec (hffr)/ v-guard (hffr). supply and fixing 8 way spn distribution board with ip-43 protection (metal door) suitable for 1 no. 40 a single phase elcb / rccb/dp isolator as incomer and 8 nos. 6-32 a 10ka sp mcbs as outing going including internal connection and labour charges for surface / flush mounting etc., complete makes :legrand / schneider / siemens /l&t / cabtree xpro / abb / c&s supply and transportation of of inverter model cool type split ac unit with high wall mounted single split 100% copper indoor and outdoor ondencing unit hermetically sealed compressor suitable for operation on 230v, 50hz, 1phase ac supply capable of performing heat cool dehumidifying air circulating and filtering with cooling and condensing units with 3.0 mts of copper piping, insulation kit and 4 mts of 4 core copper and cordless remote control with with warranty of compressor for 5 years iand comprehensive maintenance for 2 years -2.0 / 1.8 tr 5 star capable of delivering 21600 btu/hr and above with operating on refrigerant r-32 / r-410 makes : daikin / toshibha / carrier / blue star / hitachi or equivalent -elec-6.1.1 sanitory work:- supplying and fixing of 15 mm brass body cp finish bib tap of not less than 300 grams weight screw type (full turn) with internal /external threaded conenction conforming to is 8931 including cost and conveyance of all materials, labour charges etc., complete for finished item of work in all floors. supplying and laying, filling, jointing and testing swg sp-1 pipes of isi make confirming to is 1651 & 4127 1st quality with air tight cement joints in cm (1.5:1)prop. including excavation of trenches and socket pits in any soil (except rock requiring blasting) and refilling with watering and tamping including cost and conveyance of all materials to site and all labour charges for finished item of work (apss no 1301 & 1318) supply and fixing of 110mm dia isi mark pvc rain water spouts of 4 kg/cm2 pressure including cost of necessary pvc bends, shoes and m.s.clamps and all other accessories and fixing in position including cost and conveyance of all materials to site , seigniorage charges sales and other taxes on all materials, all operational, incidental and labour cahrges such as fixing in alignment etc., complete for finished item of work.(apss no1328) in all floors constructing 904.0 mm (3’0”) dia solid block masonry inspection chamber as per is - 4111: part-1:1986 with cement mortar (1:6) prop using fly ash blocks of 225mm thick from approved source having a minimum crushing strength of 10 n/sq.mm including plastering with cement mortar 1:3 prop; ½” thick both inside and outside fitted with 20” dia rcc manhole covers and frames including excavating pits up to a depth of 904 mm (3-0) in all sorts of soils (exculding rock) and laying cement conrete (1:4:8) 150 mm thick using 40 mm hbg metal and p.c.c. 1:2:4 benching and channel 100 mm thick as per standard specification and including cost and conveyance of all materials like cement, sand, bricks, water etc., to site, cost of seigniorage charges on all materials and all incidental and operational, labour charges like mixing cement mortar, constructing masonry, lift charges, curing etc., complete for finished item of work as per standard specification. supplying and fixing of swr/ pvc pipes (as per isi standards) 4 kg/sq.cm. prince/sudhakar or any isi brand and fixing all special such as plain bends, off sets, door bends, single junctions, double junctions as per site requirement, fixing with pvc clamps if necessary with required number of bombay nails including cost and conveyance of all materials to site, labour charges etc.complete for finished item of work at all floor levels. (apss no. 1302 1319 & 1326) 110mm dia 3 mts single socket providing and fixing factory made solid wood polymer composite (wpc) single extruded door frame section of 100*65 mm with encapsulation of 6 mm rigid layer on all external surfaces. the door frame will have a rebate of 32mm/ 37 mm. the two vertical members are to be joined together with the horizontal member using 8x75 mm long ms star full thread screws to be used with reverse forward speed control hand drilling machine. the ready/assembled door frame is fixed to wall using z hand fast 300 mm long hold fast etc. complete as per manufacturers specification and direction of engineer-in-charge for finished item of work providing and fixing 30mm thick solid panel pvc door shutter consisting of frame made out of m.s. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles, & 15mm x 15mm for top & bottom rails. m.s. frame shall have a coat of steel primers of approved make and manufacture. m.s. frame shall be covered with 5mm thick heat moulded pvc ‘c’ channel of size 30 x 50mm forming stiles, and 5mm thick, 75mm wide pvc sheets for top rail, lock rail & bottom rail on either side, and 10mm (5mm x 2) thick, 20mm wide cross pvc sheet as gap insert for top rail & bottom rail. panelling of 10mm thick pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with 30mm wide x 5mm thick pvc sheet beading on either side, and joined together with solvent cement adhesive etc. an additional 5mm thick pvc strip of 20mm width is to be stuck on the interior side of the ‘c’ channel using pvc solvent adhesive. complete as per direction of engineer-in-charge, manufacturer’s specification & drawing for finished item of work . supplying and fixing 580 mm x 440 mm long orissa pan white glazed water closet 1st qualityisi marked confirming to is:2556-part-3-1981 with p or s trap hindware / parryware / neycer with brick masonry seat, cc squatting plate and fixing 12.70mm dia np push cock 1st quality , p trap or s trap of indian w.c. shall be encased on cc (1:2:4) 150mm alround well above the joint to stop leakage at the joint etc., complete including cost and conveyance of all materials to site, cost of cc bed, labour charges and seigniorage charges etc., complete for finished item of work. supply and fixing of ashirvad/ajay/astral flowgaurd or equivalent cpvc pipes and fittings including the cost of pipe, required number of connectors such as elbows, tees, couplers, connectors, solvent cement etc., and labour charges complete including cost and conveyance of all materials to site, all operational, incidental , labour charges, etc. complete for finished item of work as directed by engineer-in charge: 22.2 mm od pipe sdr 13.5 supply and fixing of ashirvad/ajay/astral flowgaurd or equivalent cpvc pipes and fittings including the cost of pipe, required number of connectors such as elbows, tees, couplers, connectors, solvent cement etc., and labour charges complete including cost and conveyance of all materials to site, all operational, incidental , labour charges, etc. complete for finished item of work as directed by engineer-in charge: 28.6 mm od pipe sdr 13.5 supplying and fixing ppr ball valve of 25 mm dia confirming to din standards 8077/8092 , indian make heavy type including cost and conveyance of all materials , labour charges etc. complete for finished item of work. providing and placing on terrace (at all floor levels) polyetheylene water storage tank with double layer approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet and outlets and over flow pipes but without fittings and base support for tanks including cost and conveyance of all materials and labour charges for placing and fixing in position as directed by engineer-in-charge.