providing infrastructure requirement in tahsil charminar (v)(m) in hyderabad district - providing and fixing factory made polyvinyl chloride (pvc) door frame of the size 50 x 47mm with a wall thickness of 5mm, made out of extruded 5mm rigid pvc foam sheet, mitre cut at two corners and joined with 2nos. of 150mm long brackets of 15x15mm m.s. square tube. the two vertical door profiles are to be reinforced with 19x19mm m.s. square tube of 19 gauge. the door frame shall be fixed to the wall using 65/100mm long m.s. screws through the frame by using pvc fasteners. a minimum of 4nos. of screws to be provided for each vertical member & minimum 2nos. for horizontal member etc. complete as per manufacturers specification and direction of engineer-in-charge for finished item of work providing and fixing 30mm thick solid panel pvc door shutter consisting of frame made out of m.s. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles, & 15mm x 15mm for top & bottom rails. m.s. frame shall have a coat of steel primers of approved make and manufacture. m.s. frame shall be covered with 5mm thick heat moulded pvc ‘c’ channel of size 30 x 50mm forming stiles, and 5mm thick, 75mm wide pvc sheets for top rail, lock rail & bottom rail on either side, and 10mm (5mm x 2) thick, 20mm wide cross pvc sheet as gap insert for top rail & bottom rail. panelling of 10mm thick pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with 30mm wide x 5mm thick pvc sheet beading on either side, and joined together with solvent cement adhesive etc. an additional 5mm thick pvc strip of 20mm width is to be stuck on the interior side of the ‘c’ channel using pvc solvent adhesive. complete as per direction of engineer-in-charge, manufacturer’s specification & drawing for finished item of work . supply and fixing of door with single leaf shutter, door size 0.90x2.13 mtrs with medium teak wood frame of sections size 75mm x 100mm with flush door shutter solid bond wood black board type with commercial ply on both faces of 35mm thick including cost of fixtures such as m.s.powder coated tower bolts 250mm long 1 nos, ms powder coated handels 150mm long 1 no, 300mm long ms powder coatedaldrops 1no, 125mm long ms powder coated butt hinges 3 nos, 300 mm long ms powder coated flat latch 1no, door stoppers 1 nos, ms hold fasts 6nos, sales and other taxes cost and convenyance of all materials to site all labour charges such as fixing of door frame on shutter fixing in position , with hardware fixtures etc., complete for finsihed item of work. providing and applying wall putty of white cement or polymer or cement based of average 1 to 2 mm thickness over plastered surface to prepare the surface even and smooth after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface, clean & wipe off loose dust, applying knifing paste filler by putty knife / muslin pad, air dry for 2 - 3 hrs, sand with 180 and 320 no., emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges, over heads and contractors profit etc., complete for finished item of work in all floors for internal walls painting to new walls with two coats of acrylic emulsion paint of superior quality of approved brand and shade over base coat of cement primer interior grade -i making three coats in all to give an even shade after thoroughly brushing the surface to remove all loose powdered materials, including cost and conveyance of all materials, including cost and conveyance of all materials, cost of brushes, water to site, etc., sales & other taxes, all operational, incidental and labour charges such as scaffolding charges, lift charges, curing etc., complete for finished item of work in all floors for internal walls.(apss no. 912) in all floors painting to new walls with two coats of acrylic emulsion paint of superior quality of approved brand and shade over base coat of cement primer exterior grade -ii making three coats in all to give an even shade after thoroughly brushing the surface to remove all loose powdered materials, including cost and conveyance of all materials, including cost and conveyance of all materials, cost of brushes, water to site, etc., sales & other taxes, all operational, incidental and labour charges such as scaffolding charges, lift charges, curing etc., complete for finished item of work in all floors for external walls.(apss no. 912) in all floors flooring with nano polished vitrified floor tiles of 1st quality and make as approved by engineer-in-charge of size not less than 600 mm x 600 mm , 8mm thickness regular finish and normal colours with borders and design as per the approved flooring pattern as directed by the engineer-in -charge, laying tiles using spacers of 2mm thick, set over a base coat of cm (1:8) prop. 12mm thick using screened sand over cc bed already laid or rcc roof slab , including neat cement slurry of honey like consistancy spread @ 3.3 kgs per sqm. and jointed neately with white cement paste to full depth mixed with pigment of matching shade including cost and conveyance of all materials like cement, sand, water, tiles, white cement etc., to site (excluding cost of c.c. bed) including cost of base coat and all labour charges for mixing of cement mortar, laying tiles to required slope as directed by the engineer- in-charge etc.,and overheads & contractors profit complete for finished item of work. (apss no.701 & 707) providing impervious coat with required slopes in cm (1:3) prop. 20mm thick (average) mixed with water proofing compound manufactured by reputed manufacturers as approved by engineer-in-charge at 1kg/bag of cement, laid over roof slab when it is green, finished smooth with a floating coat of neat cement and thread lining at regular intervals of 45cmx45cm including cost and conveyance of all materials like cement, sand, water proofing compound, water etc., to site, sales & other taxes on all materials, all operational, incidental and labour charges such as mixing mortar, laying, rounding off at junctions of wall and slab, rendering smooth with thread lining, curing, lift charges, etc., complete but excluding seigniorage charges for finished item of work (apss no. 901 & 903). supplying and fixing gyp board fine line grid false ceiling (gs-flc-4.6)using 12.5mm thick gyp board sheet tiles of size 595mm x 595mm conforming to is 2095 - 1992 fixing to gyp steel precoated gi wall angle of size 25mm x 25mm x 0.70mm thick along the perimeter of ceiling screw fixed to brick work / partition at 610mm center to center and suspending the frame work using precoated gi tee section (24mm x 38mm x 0.7mm) from soffit at 1220mm center to center fixed with gi soffit cleat, rawl plugs and steel expansion fasteners & connecting clip to the gi tee section with 4mm dia gi rod with galvanised spring steel level clip of pvc unversal holding clips system at 1200mm center to center and fixing the 12.5mm gypboard sheet tiles of size 595mm x 595mm and finishing two coats of drywall top coat, overheads and contractor profit complete for finished item of work in all floors. providing and fixing of louvered ventilators made of pre-painted steel as per is 513 of 0.80 mm thick galvanized as per is 277 with a polyester paint with and fitted with 4 mm thick plain float glass including fixing the frames in concrete/masonry wall by means of self expanding screws, etc., complete for finished item of work for (i) single fixed louvers ventilator size of 2’ 0” x 2’ 0” (609.6 x 609.6mm) outer frame box section size of 80 x 45mm and (ii) double fixed louvers ventilator size of 4’ 0” x 2’ 0” (1219.2mm x 609.6mm) outer frame box section size of 80 x 45mm, vertical mullion section size of 80 x 60 mm and (iii) double fixed louvers ventilator size of 4’0” x 3’0” (1219.2mm x 914.4mm) outer frame box section size of 80 x 45mm , vertical mullion section size of 80 x 60 mm supply and transportation of of inverter model cool type split ac unit with high wall mounted single split 100% copper indoor and outdoor condencing unit hermetically sealed compressor suitable for operation on 230v, 50hz, 1phase ac supply capable of performing heat cool dehumidifying air circulating and filtering with cooling and condensing units with 3.0 mts of copper piping, insulation kit and 4 mts of 4 core copper flexible chord (voltage range 160- 264 volts) and cordless remote control with with warranty of compressor for 5 years iand comprehensive maintenance for 2 years 2.0 / 1.8 tr 5 star capable of delivering 21600 btu/hr and above with operating on refrigerant r-32 / r-410 makes : daikin / toshibha / carrier / blue star / hitachi or equivalent wiring with 2 runs of 22/0.3mm (1.5 sq.mm) fire retardant low smoke (frls) / hffr p.v.c. insulated 1100 v grade as per is: 694 / 1990 specification for flexible copper cable (isi mark) in existing pipe with 6a 1 way modular switch, ceiling rose including all labour charges etc., complete for light, bell, fan and exhaust fan points in non-residential buildings makes of wires : finolex / rr kabel / havells / polycab / kei (hffr) /dec (hffr)/ v-guard (hffr). makes of switches : legrand myrius / havells fabio / million mway/ gold medal curve / anchor roma viola / cpl vysma/ vimal / gm four-five / salzar / infinity supply and run of 3 of 2.5 sq mm pvc f.r l.s. / hffr p.v.c. insulated flexible copper cable 1100 v grade as per is: 694 / 1990 specifications in the existing conduit pipe for run of mains from main panel board to tpn dbs with pin type lugs and connection. makes of wires : finolex / rr kabel / havells / polycab / kei (hffr) /dec (hffr)/ v-guard (hffr). supply and fixing of 16a/6a 3pin plug socket with shutter and 16a modular switch control duly recessed in wall with galvanised hot deep box of with common switch board including earth connections and all labour charges etc., complete. makes of switches : legrand myrius / havells fabio / million mway/ gold medal curve / anchor roma viola / cpl vysma/ vimal / gm four-five / salzar / infinity supply,transportation of light duty exhaust fan 9(225 mm) size 900 rpm with metal blades wiremesh with all accessories etc complete. makes : crompton / bajaj bahar wg / havells ventil air-db / orient hill air. supply and fixing and transportation of 22w +/ 10% , >/ 2300 lumens, 1200mm length led light housing made with alluminium anodised body, wide operating voltage with pf≥0.9, surge protection: > 2kv, thd<10%, with inbuilt driver and frosted cover cct: 3000k - 6500k as desired by the department as per is, minimum cri≥80 etc., complete with 5 years warranty with bis certification with bis certification. luminaire make: phillips / osram / ge venture / wipro / crompton / bajaj / havells / jaquar / ib led / panasonic / halonix / hpl / syska / eveready / surya / keselec/ fiem / arraystorm / gm / goldmedalled make : philips lumileds / cree / nichia / osram / samsung / lg leds. supply, transportation of energy efficient fan, 1200 mm sweep, aluminium body, consuming 28 w, bee 5 star rated, ceiling fan with brush less direct current(bldc)motor, class of insulation: b, 3 nos blades, 30 cm long down rod, 2 nos canopies, shacklekit, safety rope, copper winding, power factor greater than 0.90, service value (cmmav) greater than 8.5, air delivery minimum 235 cmm, 350 rpm (tolerance as per is:374-2019), thd less than 10%. with remote or compatible to electronic step type regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree c(max), insulation resistance more than 2 mega ohm, suitable for 230v, 50 hz, single phase ac supply, earthing etc., including all standard accessories etc., complete.makes : atomberg (efficio ) / havells / orient supply and fixing of modular electronic stept type fan regulator hum free step type socket size with ms box, front plate in the existing switch board ( modular type ) makes makes of switches : legrand myrius / havells fabio / million mway/ gold medal curve / anchor roma viola / cpl vysma/ vimal / gm four-five / salzar / infinity labour charges for fixing of ceiling fan and regulator including transportation and giving connections with twin core wire etc., complete. makes : finolex / rr kabel / havells / polycab / gm / million / v-guard (hffr) / gold medal / kundancab / hpl / rpg /nandicab / nakoda / payal / finecab / gemini / vimal /suncab supplying and fixing approved make wash down european water closet of 1st quality conforming to is:2556-part-2-2004 of white glazed with s trap,supplying and fixing best indian make plastic seat and lid for european water closets with rubber or plastic buffers as per is 2548-1996 and 10 litres capacity single flush pvc low level cistern with internal components and fixed using required size of nails and screws, 15 mm brass angle stop valve of quarter turn spindle type of not less than 400 grams weight with internal threaded conforming to is 8931, 15mm pvc connections with brass union nuts cp coated including cost and conveyance of all materials to site, overheads & contractors profit etc., complete for finished item of work for all floors. supply and fixing of white glazed flat back bowl urinals of size 440 mm x 265 mm x 315 mm with internal rim flushing mm fixied with screws complete inidan make (hs w/parry/neycer) conforming to is 2556 -1995 as approved be engineer - in - charge 12.7 mm pvc connection with brass plumber union nuts cm coated. including 12.70 mm push cock 1st qulaity of approved make including supply & fixing 31.75 m dia pvc flexible waser pipe of 914.40 mm lenght of 1st including cost and conveyance of all materials to site labour charges etc., complete for finished item of work for all floors s&f of 15 mm brass body cp finish bib tap of not less than 300 grams weight with quarter turn spindle with either internal or external threaded connection conforming to is 8931 including cost and conveyance of all materials, labour charges etc., complete for finished item of work in all floors. supplying and fixing indian make flat back wash hand basin (hsw/parryware/ neycer) 1st quality conforming to is:2556-part-4:1972 of size 550mm x 400mm with waste fittings like rubber plug, chain, 32 mm nominal size c.p. fitting with parallel pipe thread conforming to is:2963-1979 and fitted with 15 mm nominal bore chromium plated pillar tap of 1st quality indian make 400 grams seiko/ esso or equivalent complete with standard ci brackets including wooden block ,1 no.12.70mm pvc connection with brass union nuts cp coated , 1 no.12.70mm np bib tap 300 gms seiko or equivalent including cost and conveyance of all materials to site, labour charges etc. complete for finished item of work supply and fixing of ashirvad/ajay/astral flowgaurd or equivalent cpvc pipes and fittings to meet the requirement of astm-d 2846 and are produced in cts( copper tube sizes 1/4 to 2 ) ashirwad flowgaurd sdr11 and sdr 13.5 pipes are made from identical cpvc components having the same physical properties for hot and cold water confirming to (is 15778-2007) 28.60mm supplying and fixing ppr ball valve of 25 mm dia confirming to din standards 8077/8092 , indian make heavy type including cost and conveyance of all materials , labour charges etc. complete for finished item of work. providing and placing on terrace (at all floor levels) polyetheylene water storage tank with double layer approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet and outlets and over flow pipes but without fittings and base support for tanks including cost and conveyance of all materials and labour charges for placing and fixing in position as directed by engineer-in-charge.