tender for construction of two class room building pues at mangankadu habitation in sundaranayagipuram panchayat. cfsids 2023-24; 1 construction of two class room building pues at mangankadu habitationinsundaranayagipuram panchayat.cfsids 2023-24 2 earth work excavation in all class of soil except hard rock requiring blastingwith intial lead and lift etc. complete for foundation as per ss 20a 3 sand filling with good river sand including cost and conveyance of all materials and all labour charges for etc completed. 4 cement concrete 1 : 4 :8 mix using 40mm hbg metal for foundation including watering wherever necessary and laid in layers of not more than 15cm thick., compacting etc., complete complying with standard specifications and as directed for base course below wearing course to street. 5 refilling the approved good quality earth in plinths, area development etc. wherever specified in layers is not exceeding 200 mm thick, with available earth at site. 6 supplying and filling of good earth filling locally available earth transported from the outside including consolidation, leveling specifiedin layers of not exceeding 200 mm thick., etc. complete. 7 supplying & erecting centering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, complete complying with standard specifications and as directed by the departmental officers. rate for 10m2.for the following items. ( rcc floor slab, roof slab, rectangular / square, tee / ell beams, lintels, staircase waist slabs, landing slabs, landing beam, portico beam etc., ) . 8 grade beam 9 sunshade&loft, lintel beam and roof slab 10 column 11 cement concrete 1:1-1 / 2:3 ( one cement, one and a half crushed stone m.sand and three hard broken stone jelly ) using 20 mm gauge hard broken granite stone jelly for all rcc items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the rcc floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with cement mortar 1:3 ( one cement and three m.sand ) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers 12 foundation & basement 13 ground floor 14 steel - fe 500 d: supply, fabrication and placing of reinforcement steel of high yield strength ribbed bars of various diameters and grade conforming to is 1786 for reinforced concrete work. the work includes recoiling, straightening, cutting, bending, fabricating, and placing in position, at all levels including lead and lift, according to drawings, specifications etc. complete and supply & use of 18g black annealed binding wire double fold to tie the bars in position and providing precast cement / pvc cover blocks for main reinforcement to ensure specified cover and complete., including all labor charges etc as directed by departmental officers. 15 brick work in following cement mortar 1:5 using best quality ii class table moulded bricks 83 / 4 x 41 / 4 x23 / 4 for foundation and basement including curing etc., complete complying with standard specification.including scaffolding curing cost of reinforcement etc.all complete as per specifications and drawings as directed by the engineer in-charge. 16 foundation & basement 17 ground floor 18 brick partition walls of 11.50cm thickness using best qualityii class table moulded bricks 83 / 4 x 41 / 4 x23 / 4 in cement mortar 1:3 ( one cement and three sand ) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. 19 ground floor 20 terrace floor 21 providing and applying 10 mm thick cement plaster in cement mortar 1:3 ( one part of cement and three parts of sand ) , to finishing the exposed surfaces of r.c.c. items of works such as roof ( or ) floor slabs, beams, and sun shades etc.to correct plane and level including scaffolding, hacking of surface, chiselling the undulated surface wherever necessary and curing etc., all materials and labour complete in all respects including all lead, lift and descent and as directed by the enineer in charge. this rate includes the cost of providing cement mortar beadings for sun shades, steps, landing slabs, elevation etc. complete complying with standard specifications. 22 providing & applying 12 mm thick cement plaster in cm 1:5 ( 1 part of cement: 5 parts of sand ) to walls internally in single coat at all levels to correct line and level including chicken wire mesh at all joints of brick and concrete surfaces with minimum overlap of 150 mm in all directions, scaffolding, rounding off or chambering of corners, offsets, fin / bands, projections, etc. and cleaning of surface, raking out joints, roughening of surface, chiseling the undulated surface wherever necessary and curing, etc., all materials and labor complete in all respects including all lead, lift and descent andas directed. 23 providing & applying 20 mm thick cement plaster in cm 1:5 ( 1 part of cement: 5 parts of sand ) to walls externally in single coat at all levels to correct line and level includingscaffolding, rounding off or chambering of corners, offsets, fin / bands, projections, etc. and cleaning of surface, raking out joints, roughening of surface, chiseling the undulated surface wherever necessary and curing, etc., all materials and labor complete in all respects including all lead, lift and descent andas directed. 24 paving the floor with best approved quality fine polished shahabadstone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than adanga marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 ( one cement and three sand ) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., the kota stone slabs and other materials to be used shall be got approved by the executive engineer concerned before use on work, etc., complete as per standard speicification 25 providing granolithic floor finish in 1 : 2 : 4 mix using 20 mm hbg metal for foundation including watering wherever necessary and laid in layers of not more than 15cm thick., compacting etc., complete complying with standard specifications and as directed. - rate for 10 m3 26 fabricating, supplying and fixng in position of steel sheeted windows ( three leaves ) with the following specifications. outer frames of windows made of z section f7d of size 33 x 25 x 3mm at 1.419 kg / m and mullion j section ( f4b ) of size 46x25x3mm at 2.28kg / m and shutter section of made off7d of 33x25x3mm at 1.419 kg / m as specified in is 7452 / 1990. each openable shutter should not exceed a width of 600mm to enable separate operations and easy maintenance. the panel of the shutters to be covered with 18 gauge cold rolled sheet of superior quality and welded intact with shutter frames. horizontal stiffeners using 18x5mm ms flat at 0.70kg / m at 3 nos. for each shutter and additional diagonal stiffners of the same ms flats at all the four corners of each shutters to the suitable length welded to the shutters, for holding the cr sheets in position firmly. 2 numbers of sturdy hinges and one number of handle-cum-latch of special type made with 18x5mm ms flats are revetted to the shutters at an appropriate height in window. suitable opening is left for its easy operation. a stopper square rod for handle is provided in the mullion section at suitable place to catch the window handle. each window shutter having an adustable stay made out of 18 x 5mm at 0.70 kg / m ms flat of lenght 320mm with three adjustable position. a matching peg is provided in the outer frame of the window at suitable place. 4 nos. of hold fasts of 120mm length spliced at the ends are welded to the outer frame of the window by using ms flat of 18x5mm at 0.70kg / m, welded to the shutter at two place equivalent from each from top and bottom of the shutter. an ms square bar of 12mm size is welded to the inner face of the window at an equal interval not exceeding 100mm edge between them. all members are painted with one coat of anti-corrosive red oxide primer as directed by the departmental officers.all sections should be in confirmed with is 7452 / 1990.the cost includes cost of all materials, labour charges and other incidental charges, etc., complete 27 manufacturing, supplying and fixing of steel doors with following specification.ms angle of size 40x40x6mm at 3.5 kg / m used for outer frame and ms angle of size 35x35x5mm at 2.6 kg / m for the shutter frame.stiffeners with 32x6mm at 1.5 kg / m ms flat is provided as the lock rail of the door and welded intact on both ends to the shutter frame.18 g cr sheets of best quality is laid as panel in theshutter frames.18x5mm at 0.70 kg / m ms flat is welded over the 32x6mm at 1.50kg / m ms flat on the rear side of the door, sandwiching the cr sheet for rigidity. additional stiffeners with 18x5mm at 0.7 kg / m ms flats are provided diagonally on the rear side of the shutter. 300mm length ofhinges 2nos, for shutter is provided.6 nos. of 250mm length hold fasts 200mm length specified at the ends are welded to the outer frame of the door.tower bolt 2 nos. at the top provided. 28 supplying and painting new plastered surface with two coats of distempering one coat of distemper primer 29 supplying and painting new plastered internal wall surface with two coats of distempering one coat of distemper primer 30 supplying and painting the walls with one coat of wall primer and two coats of exterior emulsion ( apex or equivalent ) as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications ( the colour and shade of the cement paint shall be got approved by the executive engineer before use of work ) . 31 weathering coarse with brick jelly lime concrete using 20mm brick jelly with slacked lime in the ratio f 32:12.5 including cost and conveyance of all materials to site and all labour charges for mixing , laying , and finishing etc complete 32 finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in cement mortar 1:3 ( one cement and three sand ) 12mm thick mixed with water proofing compound conforming to iss at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers. 33 painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. ( the make, quality and colour of paint should be got approved by the executive engineer before use on works. ) 34 supplying and fixing cuddapah slab for cupboard shelf 35 providing cup-board shutter with frame using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the departmental officers. the design pattern, water proof plywood, laminate sheet and other materials should be got approved from the executive engineer befoe use on wor 36 supplying and fixing pvc rain water down fall pipes of following dia meter etc., complete. 37 electrification 38 wiring 2 x 1.5 sq.mm ( 22 / 0.30 ) pvc insulated unsheathed sc.cu.conductor of 1100 v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box with in flush with wall covered with hylem sheet of 3 mm thick with painting of suitable colour for concealedpvc light / fan point ( sd no.25 ) 39 supply and fixing of4-18wled tube with fitting inclusive of all charges 40 wiring 2 x 1.5 sq.mm ( 22 / 0.30 ) pvc insulated unsheathedsc.cu. conductor of 1100 v grade in suitable pvc rigid pipe on wall and ceiling with pvc accessories with tw switch box with in flush with wall covered with hylem sheet of 3 mm thick with painting of suitable colour for concealedpvc plug point ( sd no.38 ) 5 pin plug point 41 wiring with 2 x 4 sq.mm. ( 56 / 0.3 ) pvc insulated sc unsheathed copper conductor cable of 1100v grade in suitable heavy gauge ms conduit pipe concealed in wall and ceiling with ms accessories in flush with wall with 150mm x 100mm x 75mm ms switch box concealed type with 3mm thick hylum sheet cover for 15a 3 pin flush type non interlocking cs plug with continuous earth wire connection of 14 swg tc wire and rnaking good of the concealedportion for concealed power plug point ( sd no.15 ) 15 pin plug point 42 supply and fixing of 1200mm sweep ac ceiling fan complete with stepped electronic regulator with 300mm down rod on the existing clamp sd 106 43 supply and fixing of water tight bulk head fitting with guard ( philips / bajaj / crompton / klite ) suitable for incandencent lamp and 60w bulb ( sd n0.83 ) 44 supply and run of 2 of 1.50 sq.mm polythene insulated pvc sheathed heavy duty sc copper conductor of 1100 v grade on 7 / 20 gi bearer wire for service connection mains ( sd no.64 ) 45 supply and fixing of tneb meter board suitable for 32a single phase service connection with 32a fuse unit ( 500v ) 32a neutral link and earth link ( 1 x 1 / 8 copper flat ) on tw plank of size 375mm x 300mm x 19mm with supporting tw reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the tw plank on wall with earth connection and inter connection with 7 / 20 pvc insulated copper wire from eb meter to fuse unit. ( sd no. 125 ) 46 supply and run of 2x4 sqmm ( 22 / 0.3 ) pvc insulated sc unsheathed cu.conductor of 1100v grade in 25mm dia gi pipe ( class b ) suitably bent at both ends with necessary angle iron upright and end supports for mains sd 70 47 supply and fixing of 16 amps dp switch of500v with metal clad with fuse and neutral sd 142 48 sd 139 49 sd 134 50 sd 234 51 plinth protection 52 earth work excavation for foundation in all clauses of soils and sub soils to full depth as may be directed except in hard rock requiring blasting but inclusive of shoring strutting and boiling out water whenever necessary et complete complying with standard specification 53 supplying and filling in basement with filling riversand in layer of not more than 15 cm thick well rammed etc., complete. 54 cement concrete 1:4:8 mix ( one cement four sand and eight aggregate ) using 40mm gauge handbroken granite tone jelly for foundation including dewatering if found ecessary and laid in layers of not more than 15 cm thick and compacted, etc., complete complete 55 brick work in cm 1:5, using country bricks, including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc compete. 56 providing granolithic flooring with cc 1:2:4, using 10-12 mm chips, 25 mm tk, including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc compete. 57 plastering in cm 1:5, 12 mm tk, including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc compete. 58 gst amount for providing service to government contract works for the above construction works. { gst amount is the total gst amount for total overall quoted amount above this row in column bb for all works in this package }