tender for extension of emergency doctor room and renovation of toilet at aiims rishikesh; 1 providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge. (glazing, paneling and dash fasteners to be paid for separately) : for fixed portion powder coated aluminium (minimum thickness of powder coating 50 micron) 2 for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of epdm rubber / neoprene gasket required (fittings shall be paid for separately) powder coated aluminium (minimum thickness of powder coating 50 micron) 3 providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (cost of aluminium snap beading shall be paid in basic item): with float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) 4 providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to is: 12823 grade l type ll, in panelling fixed in aluminum doors, windowsshutters and partition frames with c.p. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin-charge. pre-laminated particle board with decorative lamination on both sides 5 supply and installation of aluminium composite panel sheet 4mm thick in mild steel framing by using screws and uv protective silicon in joints all complete as per instruction of engineer-in-charge. 6 providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of engineer- in-charge. 7 providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with isi, is : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete 8 providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :-200x10mm 9 providing and fixing aluminium sliding door bolts, isi marked anodised (anodic coating not less than grade ac 10 as per is : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete 300x16 mm 10 providing and fixing aluminium handles, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.125mm 11 providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of engineer-in-charge 12 providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per directions of engineer- in-charge. 13 wall painting with acrylic emulsion paint, having voc (volatile organic compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. one coat 14 wall painting with acrylic emulsion paint, having voc (volatile organic compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. two coat 15 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 16 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 17 providing & fixing sun ray film, thickness 50 micron and rejects up to 71% of the sun’s heat, glare reduction 96% made with a scratch-resistant coating & blocks harmful uv as per direction from engineer-in-charge. (based on item 8.30.1) 18 providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of size 595x595mm of approved texture, design and patterns as per cpwd specification 2019, to be laid in true horizontal level suspended on inter-locking metal t-grid of hot dipped galvanised iron section of 0.33mmthick (galvanized @ 120 grams per sqm including both sides)comprising of main-t runners of size 24x38 mm of length 3000 mm,cross - t of size 24x32 mm of length 1200 mm and secondaryintermediate cross-t of size 24x32 mm of length 600mm to formgrid module of size 600 x 600 mm, suspended from ceiling usinggalvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 12x50 mm long dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and l-shape level adjuster of size 76x25x25x1.6 mm fixed with grid and z cleat of size 25x37x25x1.6mm thick with precut hole on both 25mm flange to pierce into 12x50mm or even bigger size dash fastener if require, fixed with glavanised iron perimeter wall angle or size 24x24x0.40 mm of length 3000 mm to be fixed on periphey wall / partition with the help of plastic rawl plugs at 450mm center to center and 40 mm long dry wall s.s screws. the workshall be carried out as per specifications, drawing and as per directionsof the engineer-in-charge.with 15 mm thick tegular/butt edged without perforation plain/designer light weight calcium silicate anti-microbial bio-safe coated false ceiling tiles confirming to jis-z2801 and astm g-21 19 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. 20 mm nominal outer dia pipes 20 providing and fixing floor mounted, white vitreous china single piece,double traps syphonic water closet of approved brand/make, shape,size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing p/s trap, complete in all respect as per directions of engineer-in-charge. 21 providing and fixing c.p. brass angle valve for basin mixer and geyser points of approved quality conforming to is:8931, 15 mm nominal bore 22 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level :1:5:10 (1 cement : 5 coarse sand (zone-iii) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 23 providing and fixing p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete.flexible pipe 32 mm dia 24 providing and fixing uplasticised pvc connection pipe with brass unions : 45 cm length 15 mm nominal bore 25 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:white vitreous china wash basin size 550x400 mm with a pair of 15 mm c.p. brass pillar taps 26 dismantling aluminium/ gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by engineer-in-charge. 27 half brick masonry with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundations and plinth in :cement mortar 1:4 (1 cement : 4 coarse sand) 28 12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand) 29 15 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 fine sand) 30 dismantling w.c. pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of engineer-in- charge. 31 dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :of area 3 sq. metres and below 32 dismantling old c.i. pipes including excavation and refilling trenches after taking out the pipes, breaking lead caulked joints, melting of lead and making into blocks, including stacking of pipes at site lead up to 50 metre, 80 mm diameter c.i. pipe 33 dismantling old c.i. pipes including excavation and refilling trenches after taking out the pipes, breaking lead caulked joints, melting of lead and making into blocks, including stacking of pipes at site lead up to 50 metre, 100 mm diameter c.i. pipe 34 dismantling old c.i. pipes including excavation and refilling trenches after taking out the pipes, breaking lead caulked joints, melting of lead and making into blocks, including stacking of pipes at site lead up to 50 metre, labour for cutting c.i. pipe with steel saw.80 mm diameter c.i. pipe 35 dismantling old c.i. pipes including excavation and refilling trenches after taking out the pipes, breaking lead caulked joints, melting of lead and making into blocks, including stacking of pipes at site lead up to 50 metre, 100 mm diameter c.i. pipe 36 dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. for thickness of tiles 10 mm to 25 mm 37 demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge.in cement mortar 38 providing and laying water proofing treatment in sunken portion of wcs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. this layer will be allowed to air cure for 4 hours.(b) second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. this layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. the rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. 39 providing and laying rectified glazed ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to is : 15622, of approved make, in colours white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 40 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 41 half brick masonry with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level. cement mortar 1:4 (1 cement : 4 coarse sand) 42 15 mm cement plaster on the rough side of single or half brick wall of mix 1:6 (1 cement: 6 fine sand) 43 providing and fixing factory made upvc door frame made of upvc extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. the hinge side vertical of the frames reinforced by galvanized m.s. tube of size 19 x 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of engineer- in-charge.extruded section profile size 48x40 mm 44 providing and fixing to existing door frames.30 mm thick factory made polyvinyl chloride (pvc) door shutter made of styles and rails of a upvc hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. the styles and rails mitred and joint at the corners by means of m.s. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. the styles of the shutter reinforced by inserting galvanised m.s. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. the lock rail made up of h section, a upvc hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised m.s. u cleats. the shutter frame filled with a upvc multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . the panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised m.s. rod and fastened with nuts and washers, complete as per manufacturers specification and direction of engineer-in-charge. 45 providing and fixing pressed steel door frames conforming to is: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including m.s. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by engineer-in-charge: profile b fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) 46 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including isi marked stainless steel butt hinges with necessary screws 47 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). 48 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level thermo-mechanically treated bars of grade fe-500d or more. 49 centering and shuttering including strutting, propping etc. and removal of form for shelves (cast in situ) 50 providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. granite stone slab of colour black, cherry/ruby red. area of slab over 0.50 sqm 51 providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer-in-charge.granite work 52 providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main t runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross t of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main t at 600 mm center to center to form a grid of 1200x600 mm and secondary cross t of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. main t runners to be suspended from ceiling using gi slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm gi adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main t, bottom exposed width of 24 mm of all t-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by engineer-in-charge. gi metal ceiling lay in plain tegular edge global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of g i sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending 53 providing and fixing white vitreous china pedestal type water closet (european type w.c. pan) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :w.c. pan with isi marked white solid plastic seat and lid 54 providing and fixing water closet squatting pan (indian type w.c. pan ) with 100 mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests 55 extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 56 providing and fixing ptmt pillar cock of approved quality and colour.15 mm nominal bore, 125 mm long foam flow, weighing not less than 120 gms 57 providing and fixing p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete.semi rigid pipe.40 mm dia 58 providing and fixing ptmt angle valve for wash basin of approved quality conforming to is:8931. 15 mm nominal bore 59 providing and fixing unplasticised p.v.c. connection pipe with ptmt nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length 60 providing and fixing ptmt extension nipple for water tank pipe, fittings of approved quality and colour.20 mm nominal bore, weighing not less than 40 gms 61 providing and fixing ptmt waste coupling for wash basin and sink, of approved quality and colour.waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms 62 providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto 1 metre long with s.s. triangular plate to eureopean type w.c. of quality and make as approved by engineer - in - charge 63 providing and fixing ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 64 providing and fixing ptmt 15 mm urinal spreader size 95x69x100 mm with 1/2 bsp thread and shapes, weighing not less than 60 gms. 65 providing and fixing ptmt urinal cock of approved quality and colour.15 mm nominal bore, 80 mm long, 42 mm high and 30mm wide with bsp female threads weighing not less than 48 gms 66 providing and fixing ptmt bib cock of approved quality and colour.15 mm nominal bore, 165 mm long, weighing not less than 110 gms 67 providing and fixing ptmt grating of approved quality and colour.circular type.125 mm nominal dia with 25 mm waste hole 68 providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :rectangular shape 1500x450 mm 69 providing and fixing upvc swr pipes conforming to is:13592-92 type b, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes. 160 mm diameter 70 providing and fixing upvc swr floor trap conforming to is:13592-92 type b, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, 110 mm dia 71 providing and fixing upvc swr plain bend conforming to is:13592-92 type b, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, 150 mm dia 72 providing and fixing upvc swr plain tee conforming to is:13592-92 type b, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, 150 mm dia 73 providing and fixing white vitreous china flat back urinal basin of 355x340x535mm sizewith urinal valve auto closing system and c.p. brass spreaders with brass unions and g.i clamps complete. including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 74 core cutting of size 150 mm in floor and fixing of bend of size 150 mm and making water proofing arrangement all around as per instruction of engineer in charge 75 wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm frls/hffr pvc insulated copper conductor single core cable in surface/recessed steel conduit, with modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm frls/hffr pvc insulated copper conductor single core cable etc. as required. group c 76 wiring for circuit/ submain wiring along with earth wire with the following sizes of frls/hffr pvc insulated copper conductor, single core cable in surface/ recessed steel conduit as required 2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire 77 wiring for circuit/ submain wiring along with earth wire with the following sizes of frls/hffr pvc insulated copper conductor, single core cable in surface/ recessed steel conduit as required 2 x 4 sq. mm + 1 x 4 sq. mm earth wire 78 wiring for circuit/ submain wiring along with earth wire with the following sizes of frls/hffr pvc insulated copper conductor, single core cable in surface/ recessed steel conduit as required 4 x 4 sq. mm + 2 x 4 sq. mm earth wire 79 supplying and fixing suitable size gi/pvc box withmodular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 &15/16 a modular socket outlet and 15/16 a modular switch, connections etc. as required. 80 led panel light 2x2 ft. (system lumen efficacy ≥105 <120 lm/watt), supplying, installation, testing & commissioning of panel light 2x2 ft., of following body material and construction as per is : 10322 with driver as per the requirement with driver efficiency >85%, operating voltage ac 140- 270 volt, freq 50/60 hz, operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 kv with short & open circuit protection, thd < 10% , p. f.≥0.95, ip20, cri >80, ugr (unified glare rating) < 19, flicker free, (flicker should be below 5 %), life time (led,driver & electrical circuitry), of minimum 50000 burning hours with, 70% of initial lumen maintained till life, cct /6000°k / 6500°k (as per ansi bin), sdcm(standard deviation color matching) <3, maximum power consumption should not more than the specified rating and fixture shall be of relevant bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. complete in all respect i/c connections with 1.5 sq mm frls, pvc insulated copper conductor single core cable and earthing etc. as required with minimum 5 year oem warranty. system lumen efficacy ≥105 <120 lm/watt output . lm79 & lm80 test report from nabl lab for all testing required for led fixtures as per bis shall be submitted. shape size and cct shall be as approved by engineer-in-charge as per requirement. (thermal management: heat sink of aluminum housing such that led junction temperature shall not rise above 90°c). powder coated die cast / extruded aluminium body (thickness≥ 1.20 mm),36 watt 81 supply, installation, testing and commissioning of metallic exhaust fan in the existing opening, including making goodthedamage connection with existing light point/ fan point/ exhaust fan point/ call bell point with 3 x1.5 sq.mm flexible frls pvc insulated, copper conductor cable, body earthing and sundry materials complete with testing,commissioning etc.as required following specifications size of fan (in mm) 300,number of pole (in nos.) 4,number of blades 3,rated voltage 230 v, 50 hz, ac, single phase upto 300 mm sweep size.