repairs and renovations at chc, yelamanchili in anakapalli district.-earth work excavation for foundations (manual means) of buildings, septic tank, sump, compound wall in ordinary soils and depositing on bank with an initial lead of 10m and depth up to 3m including all operational, incidental, labour charges such as shoring, sheeting, planking, strutting etc., and for finished item of work excluding dewatering charges etc., as per ss 20 b(apss 308) filling with carted coarse sand, coarse agreegates (40mm, 20mm, 10mm, 6mm) inharvesting pit initial lead in layers not exceeding 30cm thick,watering and ramming including cost and conveyance of water to work site and all peraitonal,incidental ,labour charges,hire charges of t&p etc., and ..for fnished item of work(apss no.309&310) plain cement concrete (1:5:10) (cement: fine aggregate: coarse aggregate) for foundations and under flooring bed using coarse aggregate 40mm size hard , machine crushed granite from approved quarry using concrete mixer 10 / 7 cft (0.2 / 0.8 cum) capacity including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site including all charges for machine mixing and hire charges of concrete mixer, laying concrete in foundations and under flooring bed, ramming in 15 cm layers finishing top surface to the required level curing etc.,and complete for finished item of work. (apss no. 402) plain cement concrete m 20 nominal mix using 20mm size graded machine crushed hard granite metal (coarse aggregate - as per is 383 - 1970 and is 2386 part 1 to part 8) from approved quarry using concrete mixer 10 / 7 cft (0.2 / 0.8 cum) capacity including cost and conveyance of all materials like cement, fine aggregate(sand), coarse aggregate, water etc. to site including all charges centering, labour charges such as weigh batching, machine mixing, hire charges of concrete mixer, centering charges, laying concrete in position, curing etc., & lift charges , for steps for finished item of work. (apss no. 402) supply and placing of the design mix concrete m 25 grade corresponding to is 456 with cement content of 380 kgs per 1 cum of concrete using weigh batcher / mixer with 20mm size graded machine crushed hard granite metal (coarse aggregate - as per is 383 - 1970 and is 2386 part 1 to part 8) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site, centering using steel scaffolding pipes , jack props , wallers , foot plates , brackets , steel centering plates etc., including all operational, incidental and labour charges such as weigh batching, machine mixing, lifting of concrete manually, laying concrete, vibrating, curing etc., and ..but excluding cost of steel and its fabrication charges for finished item of work (apss no. 402) for plinth beam masonry work in cm(1:6) prop (cement : sand) in superstructure with fly ash cement / lime solid blocks of size 290mm x 225mm x 140mm from approved source having minimum crushing strength of 50 kg/sqcm. including cost and conveyance of all materials like cement, sand, fly ash cement / lime solid blocks, water etc., to site, labour charges, like mixing cement mortar, scaffolding charges, constructing masonry, lift charges, curing, etc., complete for finished item of work. (apss no. 501 & 504) reinforced masonry for partition walls (100 mm thick) in cm (1:4) prop. (cement : sand) using fly ash cement / lime solid blocks of size 290mm x 100mm x 140mm having minimum compressive strength of 50 kg/sq.cmand placing 2 nos. of 6mm m.s plain rods in every third layer with free ends of the reinforcement pegged into mortar joints of main brick walls where applicable including cost and conveyance of all materials like cement, steel, sand, fly ash cement / lime solid blocks, water etc., to site, all operational, incidental charges such as labour charges for mixing cement mortar, scaffolding charges, constructing masonry, lift charges, curing, etc., and ..but excluding cost of steel and its fabrication charges complete for finished item of work. (apss no. of 509) providing thermo mechanically treated (tmt) (fe 500 / fe 500 d grade as per is 1786-1979) of different diameters for rcc works including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 swg, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying etc., and ..for finished item of work.( apss no.126) for first floor providing mild steel (ms) steel bars (fe 250 grade as per is 432) of different diameters including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 swg, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying etc., and ..for finished item of work.( apss no.126) for first floor plastering 12mm thick single coat in cm(1:5) using screened sand including cost and conveyance of all materials like cement, sand, water etc., to site and all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, curing as directed by engineer-in-charge etc., and ..for finished item of work (ss 901,903 & 904) for first floor flooring with non-skid red or white full body ceramic floor tiles of size 300 mm x 300 mm and thickness between 7-8 mm 1st quality conforming to is:13711, is:13712, is:13630 (parts 1 to 15) of any colour and finish in all shades and designs as approved by engineer-in-charge, set over base coat of cement mortar (1:8), 12mm thick using screened sand over cc bed already laid or rcc roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, screened sand , water and tiles etc., and ..for finished item of work. (apss no.701 & 707) providing dadooing with glazed red or white full body ceramic wall tiles of size 300 x 450 mm / 320 mm x 400 mm and thickness 6 mm 1st quality conforming to is:13711, is:13712, is:13630 (parts 1 to 15) of any colour and finish in all shades and designs with borders as approved by engineer-in-charge flushed to wall surface set over base coat of cm(1:5) 12 mm thick using screened sand with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointing with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc., and ..for finished item of work. supply & application of one coat water based cement primer of interior grade i and two coats of synthetic polymer luxury plastic emulsion paint of superior grade having voc (volatile organic compound) content less than 50 grams/litre for internal walls including cost and conveyance of all materials to site, incidental, operational and all labour charges etc., and ..for finished item of work in all floors. supply & application of one coat water based cement primer of exterior grade ii and two coats of acrylic exterior emulsion paint having voc (volatile organic compound) content less than 50 grams/litre for exterior walls including cost and conveyance of all materials to site, incidental, operational and all labour charges etc.,and ..for finished item of work in all floors. painting two coats with synthetic enamel paint grade-ii voc (volatile organic compound) content less than 50 grams/litre over primer coat of red oxide to new iron work including cost and conveyance of all materials to site, incidental, operational and all labour charges etc., and ..for finished item of work in all floors. (ss no. 1201, 1212 & 1207). for ground floor supply and fixing of ms door as per the drawing with frame section of 40mmx40mmx5mm ms angles with double shutters with frame size of 35mmx35mmx4mm and with two parts of the bottom half with ms sheet and the above portion of the door with ms mesh and fan light portion of the door with all required number of ms fixtures complete for finished item of work for all floors supplying and fixing of ms doors, grill to windows / in open court yards using ms angles, flat, square bars including cost and conveyance of all materials, cutting, bending, welding, all operational charges, labour charges, etc., complete for finished item of work. supplying and fixing of pre-painted galvalume trapezoidal profile roofing sheets with 0.50mm thickness, coating: alu-zinc coating az150 gsm. tensile strength: 550 mpa. paint coating: regular modified polyester painting. painting thickness (top): 18 to 20 microns, (bottom): 5 to 7 microns. sheet width: 1.020, length: maximum 12 meters with regular range colours fixed with g.i ‘j’ bolts & nuts 8 mm dia with bitumen & g.i limpet washers filled with white lead & including a coat of approved steel primer and two coats of approved paint on over lapping of sheets complete (up to a pitch of 600) etc., complete, excluding the cost of purlins, rafters, trusses including cost and conveyance of all materials , labour charges , etc., complete for finished item of work in all floors. providing & fixing of mesh windows made of pre-painted steel (base steel as per is 513 of 0.58mm thick galvanized as per is 277 with zinc of 120 gsm), primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer, section for outer frame of 47 x 36 mm, centre mullion of 60 x 36 mm, section mesh beading 18 x 6 mm and fly mesh shutter section of 20 x 40 mm, the sections cut to length meter joined with corner bracket and centre mullions fixed with mullion cap, handles, latch, 2 nos of heavy duty stainless steel pivot hinges per s.s. mesh for fly mesh shutter (304 grade) including fixing the frames in the concrete/masonry wall by means of self expanding screws complete for finished item of work. supplying and fixing of 4 (101.6mm) multi floor trap with jali - upvc/swr pipe fittings as per site requirements with standard practice for all floors including cost and conveyance of all materials to site, labour charges , etc., complete for finished item of work. supplying and fixing indian make flat back wash hand basin 1st quality conforming to is:2556-part-4:1972 of size 550mm x 400mm with 32 mm nominal size c.p. fitting with parallel pipe thread conforming to is:2963-1979 and fitted with 15 mm nominal bore chromium plated pillar tap of 1st quality indian make heavy duty complete with standard ci brackets including wooden blocks ,1 no.12.70mm pvc connection with brass union nuts cp coated , angle stop cock 12.70mm dia. first quality indian make heavy duty, 31.75mm dia. pvc flexible waste pipe 914.4mm length of 1st quality including cost and conveyance of all materials to site, labour charges , for finished item of work supplying and fixing european water closet of 1st quality conforming to is:2556-part-2-1973 of white glazed with s trap,supplying and fixing best indian make plastic seat and lid for european water closets with rubber or plastic buffers as per is 2548-1996 and 10 litres capacity single flush pvc low level cistern with internal components and fixed using required size of nails and screws, angle stop cock 12.70mm dia. first quality indian make heavy duty, 12mm pvc connections with brass union nuts cp coated including cost and conveyance of all materials to site, etc., complete for finished item of work for all floors. supplying and fixing np bib taps of size 12.70mm dia of indian make heavy duty (short body) as approved by the engineer-in-charge including cost and conveyance of all materials, labour charges , ..for finished item of work in all floors. supplying and fixing np bib taps of size 12.70mm dia of indian make heavy duty (long body) as approved by the engineer-in-charge including cost and conveyance of all materials, labour charges , ..for finished item of work in all floors. supplying and fixing of swr pvc pipes (prince/sudhakar/kisan/supreme or any isi brand) 4 kg/sq.cm. and fixing all special such as plain bends, off sets, door bends, single junctions, double junctions as per site requirement, fixing with pvc clamps if necessary with required number of bombay nails including cost and conveyance of all materials to site, labour charges, ..for finished item of work at all floor levels. (apss no. 1302 1319 & 1326) for 75mm dia supplying and fixing of swr pvc pipes (prince/sudhakar/kisan/supreme or any isi brand) 4 kg/sq.cm. and fixing all special such as plain bends, off sets, door bends, single junctions, double junctions as per site requirement, fixing with pvc clamps if necessary with required number of bombay nails including cost and conveyance of all materials to site, labour charges, ..for finished item of work at all floor levels. (apss no. 1302 1319 & 1326) for 110mm dia supply and fixing of ashirvad/ ajay/ astral flowguard or equivalent cpvc pipes and fittings sdr 11 to meet the requirement of astm-d 2846 and are produced in cts (copper tube sizes 1/2 to 2) for hot and cold water (is 15778:2007) including cost and conveyance of all materials to site, labour charges for fixing, ..for finished item of work at all floor levels. for 15.90mm od pipe supply and fixing of ashirvad/ ajay/ astral flowguard or equivalent cpvc pipes and fittings sdr 11 to meet the requirement of astm-d 2846 and are produced in cts (copper tube sizes 1/2 to 2) for hot and cold water (is 15778:2007) including cost and conveyance of all materials to site, labour charges for fixing, ..for finished item of work at all floor levels. for 22.20mm od pipe supply and fixing of ashirvad/ ajay/ astral flowguard or equivalent cpvc pipes and fittings sdr 11 to meet the requirement of astm-d 2846 and are produced in cts (copper tube sizes 1/2 to 2) for hot and cold water (is 15778:2007) including cost and conveyance of all materials to site, labour charges for fixing, ..for finished item of work at all floor levels. for 28.60mm od pipe supplying and fixing gunmetal gate ( gm peet ) valve as per is-778 class - i , indian make heavy type including cost and conveyance of all materials , labour charges , ..for finished item of work. for 15mm nominal bore supplying and fixing gunmetal gate ( gm peet ) valve as per is-778 class - i , indian make heavy type including cost and conveyance of all materials , labour charges , ..for finished item of work. for 20mm nominal bore supplying and fixing gunmetal gate ( gm peet ) valve as per is-778 class - i , indian make heavy type including cost and conveyance of all materials , labour charges , ..for finished item of work. for 25mm nominal bore providing and placing on terrace (at all floor levels)polyetheylene water storage tank with double layer approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet and outlets and over flow pipes but without fittings and base support for tanks including cost and conveyance of all materials and labour charges , ..for finished item of work. supply and fixing of 25mm outer dia (1.60 to 1.80)mm thicknes medium grade with is:9537 part 3 frls rigid surface p.v.c. pipe (isi marked) on wall with all required pvc junction boxes confirms to is : 3419 and all accessories fixing on chromium plated metallic base saddles for run of mains including all labour charges etc., complete. including all labour charges etc., complete. makes: precision/universal& marudhar/vip / goldmedal / million plast / gm / sudhakar /polycab/anchor/ polyline/ orbit/akg/beljin/vasavi/dec wiring with 2 runs of 22/0.3mm ( 1.5 sq.mm) frls / frlsh / hffr / zhfr p.v.c. insulated 1100v grade as per is : 694 / 1990 specification flexible copper cable (isi marked) in existing pipe with 6a modular switch (isi marked) with cover plate, ceiling rose/bh/ sbh, including all labour charges etc., complete for light, bell, fan and exhaust fan points etc., complete. (for non residential building).makes of wires: finolex / rr kabel / havells/finecab/kei/polycab/gloster/goldmedal/gm/ fortune arrt/anchor/million/ apar(anushakthi)makes of switchs : legrand(myrius/lyncus)/schneider(clipsal x/livia ab)/ crabtree (murano/athena)/lauritz knudsen-englaze (formerly l&t)/ gm-(four-five)/goldmedal(gifa)/million (m-vee)/anchor (roma plus)/precision(series7)/honeywell(blenzepro) supply and run of 3 of 2.5 sq.mm (phase neutral and earth) frls / frlsh / hffr / zhfr p.v.c. insulated 1100v grade as per is : 694 / 1990 specification flexible copper cable in existing ms conduit pipe for individual ligting circuits including labour charges etc., complete as required for switch boards.makes: finolex / rr kabel / havells/finecab/kei/polycab/gloster/goldmedal/gm/ fortune arrt/anchor/million/ apar(anushakthi) supply and fixing of 20-24w, not less than 1100mm length led batten light with extruded alluminium / crca housing and polycarbonate cover, input voltage ac 220 - 260 volts with pf>0.9, surge protection: 2kv, thd<15%, with high power leds having efficacy of ≥ 120 lumens / watt with inbuilt and replacable driver with earth connection brought outside and frosted cover cct: 3000k - 5700k, minimum cri>70 etc., complete including fixing on wall / ceiling with pvc/tw round blocks with all accessories including giving connections and all labour charges etc., complete with 5 years warranty.make: a) luminaire make : phillips / ge- venture / crompton / wipro / bajaj / havells / halonix/jaquar/hpl/gm / greenlites / gold medal/eveready// rhino/panasonicb) led make : philips lumileds / cree / nichia / osram / samsung/ everlight supply and transportation of 48 (1200mm) sweep star rated ceiling fan , with double ball bearings, air delivery more than 200 cubic meter/min but without regulator.makes: crompton (hs plus/hs) / havells (es plus/ss390es) /orient energy star/ halonix(zephyr)/polycab(synergy 50 isi) / g.m. (air wave premium)/bajaj-edge/arcline (glacier)