repairs and renovation at chc, madugula in anakapalli district.-dismantling, clearing away and carefully stacking useful materials for re-use and disposal of unserviceable materials with 100m lead as directed by executive engineer duly taking actual premeasurements before dismantling including all labour charges , etc., complete for brick masonry dismantling, clearing away and carefully stacking useful materials for re-use and disposal of unserviceable materials with 100m lead as directed by executive engineer duly taking actual premeasurements before dismantling including all labour charges , ..etc., complete for reinforced cement concrete dismantling, clearing away and carefully stacking useful materials for re-use and disposal of unserviceable materials with 100m lead as directed by executive engineer duly taking actual premeasurements before dismantling including all labour charges , ..etc., complete for flooring dismantling doors , windows and clear storey windows, ventilators etc., ( wood or steel ) shutters including chowkhats , architraves,hold fasts and other attachments etc., and stacking them within 100m lead including labour charge etc., ..complete for finished item of work for not exceeding 3 sqm in area : conveyance of un-useful excavated earth to a distance of 5 km for disposal including hire charges of t & p, labour charges etc., ..complete for finished item of work. earth work excavation for foundations (manual means) of buildings, septic tank, sump, compound wall in ordinary soils and depositing on bank with an initial lead of 10m and depth up to 3m including all operational,incidental, labour charges such as shoring, sheeting, planking, strutting etc., ..complete for finished item of work excluding dewatering charges etc., as per ss 20 b (apss 308) plain cement concrete (1:5:10) (cement: fine aggregate: coarse aggregate) for foundations and under flooring bed using coarse aggregate 40mm size hard , machine crushed granite from approved quarry using concrete mixer 10 / 7 cft (0.2 / 0.8 cum) capacity including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site including all charges for machine mixing and hire charges of concrete mixer, laying concrete in foundations and under flooring bed, ramming in 15 cm layers finishing top surface to the required level curing etc.,.. complete for finished item of work. (apss no. 402) for first floor vibrated plain cement concrete (1:3:6) nominal mix using 40mm size machine crushed hard granite metal and 20mm graded machine crushed hard granite metal (coarse aggregate) in (2:1) ratio from approved quarry using concrete mixer 10 / 7 cft (0.2 / 0.8 cum) capacity including cost and conveyance of all materials like cement, fine aggregate (sand), coarse aggregate, water etc. to site, all charges for mixing and hire charges of concrete mixer, centering charges, laying concrete in position, vibrating, curing, centering charges, ..etc.,for finished item of work for footings and basement .for first floor providing plinth protection with a bed of 100mm thick pcc(1:5:10) using 40mm size hb granite metal and on top of pcc, 20mm thick granolithic concrete flooring with cc(1:1:2) prop.using 6mm to 12mm size graded hard granite machine crushed metal laid monolithically already laid, in alternate panels of size not exceeding 1.5 x 1.5 mts. using 5mm thick glass strips and between the pannels and finishing the top surface to required smoothness and slopes including grooves, thread lining as directed by the engineer - in - charge including cost and conveyance of all materials to site including seigniorage charges, sales & other taxes on all materials and operational & incidental and labour charges like mixing of cement concrete, laying, curing, lift charges etc.,..complete including cost of cc bed for finished item of work. (apss no.701 & 710) for first floor supply and placing of the design mix concrete m 25 grade corresponding to is 456 with cement content of 380 kgs per 1 cum of concrete using weigh batcher / mixer with 20mm size graded machine crushed hard granite metal (coarse aggregate - as per is 383 - 1970 and is 2386 part 1 to part 8) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site, centering using steel scaffolding pipes , jack props , wallers , foot plates , brackets , steel centering plates etc., including all operational, incidental and labour charges such as weigh batching, machine mixing, lifting of concrete manually, laying concrete, vibrating, curing etc., ..complete but excluding cost of steel and its fabrication charges for finished item of work (apss no. 402) for plinth beam masonry work in cm(1:6) prop (cement : sand) in superstructure with fly ash cement / lime solid blocks of size 290mm x 225mm x 140mm from approved source having minimum crushing strength of 50 kg/sqcm. including cost and conveyance of all materials like cement, sand, fly ash cement / lime solid blocks, water etc., to site, labour charges, like mixing cement mortar, scaffolding charges, constructing masonry, lift charges, curing, etc., complete for finished item of work. (apss no. 501 & 504). plain cement concrete m 20 nominal mix using 20mm size graded machine crushed hard granite metal (coarse aggregate - as per is 383 - 1970 and is 2386 part 1 to part 8) from approved quarry using concrete mixer 10 / 7 cft (0.2 / 0.8 cum) capacity including cost and conveyance of all materials like cement, fine aggregate(sand), coarse aggregate, water etc. to site including all charges centering, labour charges such as weigh batching, machine mixing, hire charges of concrete mixer, centering charges, laying concrete in position, curing etc., & lift charges , ..for steps for finished item of work. (apss no. 402) for first floor plastering 12mm thick single coat in cm(1:5) using screened sand including cost and conveyance of all materials like cement, sand, water etc., to site and all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, curing as directed by engineer-in-charge etc., ..complete for finished item of work (ss 901,903 & 904). for comound wall plastering 12mm thick single coat in cm(1:5) using screened sand including cost and conveyance of all materials like cement, sand, water etc., to site and all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, curing as directed by engineer-in-charge etc., ..complete for finished item of work (ss 901,903 & 904). for first floor supplying and fixing single side prelam solid panel pvc door frame (choukhat): providing and fixing factory made pac single side prelam door frame of the size 50x47 mm with a wall thickness of 5mm, made out of extruded 5mm rigid pac single side prelam sheet, meter cut at two corners and joined with 2 nos. of 150mm long brackets of 15 x 15mm ms square tube. the two vertical door profiles are to be reinforced with 19 x 19mm ms. square tube of 19 guage. the door frame shall be fixed to the wall using 65/100mm long ms. screws through the frame by using pac fasteners. a minimum of 4 nos. of screws to be provided for each vertical member and minimum 2nos. for horizontal member etc. complete as per manufacture specification and direction of engineer-incharge including conveyance of all materials, labour charges for fixing, ..complete for finished item of work. providing and fixing 30mm thick brand factory made moulded pvc door shutter- wood free consisting of frame made out of ms. tubes 19 gauge thickness and size of 25mmx25mm for styles, top and bottom rails. ms. frame shall hav e a coat of steel primers. the inner panel shall consist of 25mm thick high density eps conforming to is 4671-1984 bounded with 2mm thick termite proof, water proof and fire resistant moulded pac sheet with 2,4,6 raised panel design in different plain and / or pre-lam colours after routing to the moulded design on one side and 2mm plain and / or pre-lam pac sheet on other side of the eps. the edge of panel to be sealed with lipping of 10mm wide pvc sheet bottom (made by sticking 2 rigid foam sheet of 5mm thickness using pac solvent cement) and stiles sides 25mm(5mmx5) thick and 30mm width pac sheet fitted along ms tube for lock provision for lock height 5mm thick pac sheet of size 150mmx100mm fixed with upper and lower face of inner side of eps panel etc., complete as per direction of engineer – in-charge, manufacture specification and drawing including supplying and fixing isi marked aluminium fixtures 3 nos. butt hinges (is:205) of 150mm long, 1 no. aldrop (is:2681) 250 mm long, 1 no. tower bolt (is:204) of 150 mm x 10mm dia, 2 nos. 125mm long handles (is:208),1 no. rubber / nylon door stop bushes including labour charges for fixing the shutter to frame etc., including ..complete for finished item of work for door of size 800mm x 2100mm providing specialised acrylic cementitious elastomeric waterproof coating treatment complies with astm c 297 : providing and application of two coats of acrylic cementitious elastomeric waterproof coating with- roofcoat or equavalent like high elastomeric acrylic polymer modified cementiitious waterproof system. complete for finished item of work and as directed by the engineer- in - charge including cost and conveyance of all materials , labour charges , etc., complete for finished item of work. providing mild steel (ms) steel bars (fe 250 grade as per is 432) of different diameters including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 swg, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying etc., complete for finished item of work.( apss no.126) for second floor flooring with non-skid red or white full body ceramic floor tiles of size 300 mm x 300 mm and thickness between 7-8 mm 1st quality conforming to is:13711, is:13712, is:13630 (parts 1 to 15) of any colour and finish in all shades and designs as approved by engineer-in-charge, set over base coat of cement mortar (1:8), 12mm thick using screened sand over cc bed already laid or rcc roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, screened sand , water and tiles etc., ..complete for finished item of work. (apss no.701 & 707) for first floor flooring with soluble salt porcelain vitrified tiles screen printed and polished of size 600 x 600 mm and thickness between 8-10 mm 1st quality conforming to is:13711, is:13712, is:13630 (parts 1 to 15) of any colour and finish in all shades and designs with borders and design as per the approved flooring pattern as directed by the engineer-in -charge, laying tiles using spacers of 2mm thick, set over a base coat of cm (1:8) prop. 12mm thick using screened sand over cc bed already laid or rcc roof slab , including neat cement slurry of honey like consistancy spread @ 3.3 kgs per sqm. and jointed neately with white cement paste to full depth mixed with pigment of matching shade including cost and conveyance of all materials like cement, sand, water, tiles, white cement etc., to site (excluding cost of c.c. bed) including cost of base coat and all labour charges for mixing of cement mortar, laying tiles to required slope as directed by the engineer- in-charge etc.,..complete for finished item of work. (apss no.701 & 707) for first floor providing skirting to internal walls to 10 cm height with soluble salt porcelain vitrified tiles screen printed and polished of 8 to 10mm thick of any colour and finish in all shades and designs, length equal to flooring tiles, set over base coat of cm(1:5) 12 mm thick using screened sand with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointing with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc.,..complete for finished item of work.(apss no.701 &707) providing dadooing with glazed red or white full body ceramic wall tiles of size 300 x 450 mm / 320 mm x 400 mm and thickness 6 mm 1st quality conforming to is:13711, is:13712, is:13630 (parts 1 to 15) of any colour and finish in all shades and designs with borders as approved by engineer-in-charge flushed to wall surface set over base coat of cm(1:5) 12 mm thick using screened sand with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointing with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc., ..complete for finished item of work. providing and fixing factory made upvc white colour sliding glazed window upto 1.50 m in height dimension comprising of upvc multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to upvcprofile), appropriate dimension of upvc extruded glazing beads and upvc extruded interlocks, epdm gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), g.i fasteners 100 x 8 mmsize for fixing frame to finished wall and necessary stainless steel screwsetc. profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage ofwater etc. after fixing frame the gap between frame and adjacent finishedwall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of engineer-in-charge inclusive of cost of single / double glass panes, wire mesh and silicon sealent . note: for upvc frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.two track two panels sliding window made of (small series) frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (area of window upto 1.75 sqm) supply and fixing of doors as per approved drawings with medium teak wood frame of section 100mm x 65 mm with split type fan light of 500mm at the top fixed with 4mm thick pin headed glass using 12mm x 12mm teak wood beading and 2 nos. of 10mm ms square bars and isi marked flush door shutter of 30mm thick double shutters with bond wood solid block board type core having cross bands and face veneers, hot pressed bonded with water proof phenol formaldehyde synthetic resin factory made conforming to is 2202-1991 (part-i) both sides commercial ply with internal lipping on all sides, fixing 1mm thick mat finish laminated sheet to full width and height of the flush shutter both sidesincluding cost and conveyance to site of teak wood frame, flush shutter, laminate sheet including supply and fixing 6 nos. ms z hold fasts of size 300 mm x 40 mm x 5mm including cost of isi marked alumimium fixtures of 6 nos. butt hinges (is:205) 150mm long, 1 no. aldrop (is:2681) 300mm long, 2 nos. tower bolts (is:204) of 200 mm x 10 mm dia at top, 2 nos. 150mm long handles (is:208), 2 nos. door stoppers and 2 nos. rubber / nylon door stop bushes including fixing the fixtures to door with required number of screws, bolt and nuts including labour charges for fixing the frame in position, fixing the shutter to the frame, fixing glass in fan light portion etc., including complete for finished item of work as per apss 1001 & 1002 (the vertical frame of door shall be embedded in flooring for a depth of not less than 10 mm) (1500mm x 2600mm) supply and fixing of doors as per approved drawings with medium teak wood frame of section 100mm x 65 mm with split type fan light of 500mm at the top fixed with 4mm thick pin headed glass using 12mm x 12mm teak wood beading and 2 nos. of 10mm ms square bars and isi marked flush door shutter of 30mm thick single shutter with bond wood solid block board type core having cross bands and face veneers, hot pressed bonded with water proof phenol formaldehyde synthetic resin factory made conforming to is 2202-1991 (part-i) both sides commercial ply with internal lipping on all sides fixing 1mm thick mat finish laminated sheet to full width and height of the flush shutter both sides including cost and conveyance to site of teak wood frame, flush shutter, laminate sheet including supply and fixing 6 nos. ms z hold fasts of size 300 mm x 40 mm x 5mm including cost of isi marked aluminium fixtures of 3 nos. butt hinges (is:205) 150mm long , 1 no. aldrop (is:2681) 300mm long, 1 no. tower bolt (is:204) of 200 mm x 10 mm dia at top, 2 nos. 150mm long handles (is:208), 1 no. door stopper and 1 no. rubber / nylon door stop bushes including fixing the fixtures to door with required number of screws, bolt and nuts including labour charges for fixing the frame in position, fixing the shutter to the frame, fixing glass in fan light portion etc, including ..complete for finished item of work as per apss 1001 & 1002 (the vertical frame of door shall be embedded in flooring for a depth of not less than 10 mm) (1000mm x 2600mm) supply and fixing doors as per drawings with medium teak wood frame of section 100mm x 65mm and isi marked flush door shutter of 30mm thick single shutter with bond wood solid block board type core having cross bands and face veneers, hot pressed bonded with water proof phenol formaldehyde synthetic resin factory made conforming to is 2202-1991 (part-i) both sides commercial ply with internal lipping on all sides including cost and conveyance to site of medium teak wood door frame, flush shutter, including suply and fixing 6 nos. ms z hold fasts of size 300mm x 40mm x 5mm including isi marked aluminium fixtures 3 nos. butt hinges (is:205) of 150mm long, 1 no. aldrop (is:2681) 250 mm long, 1 no. tower bolt (is:204) of 150 mm x 10mm dia, 2 nos. 125mm long handles (is:208),1 no. rubber / nylon door stop bushes including pvc door cladding 1.50mm thick to the flush doors shutters pasted with fevicol complete as per direction of engineer –in – charge, manufacturers specification and drawing to full height of the shutter inside including labour charges for fixing the frame in position, fixing the shutter to the frame etc., including ..complete for finished item of work as per apss 1001 & 1002. (the vertical frame of door shall be embedded in flooring for deth of not less than 10mm) (800mm x 2100mm) supplying and fixing of ms doors, grill to windows / in open court yards using ms angles, flat, square bars including cost and conveyance of all materials, cutting, bending, welding, all operational charges, labour charges, etc., complete for finished item of work. almirah ss1 internal size of almirah: 1850 (h) x 900 (w) x 450 (d) mm, 2 leg size of almirah: 150 (h) x 120 (w) x 450 (d) mm, 3 rack with 5 compartments. 4 distance between each shelf will be 360 mm. 5 these 4 shelves should be hanging arrangement (adjustable). 6 one shelf should have internal door and lock7 standard lock and 2 sets of keys. 8 the thickness of the almirah sheet shall be 18 swg. 9 the body of the almirah shall be manufactured from cold rolled ms sheet (c. r. sheet) with antirust treatment and shall be finished with powder coating the quality of used m.s sheet for making almirah shall be free from any pitting and corrosion etc. 10 h/d rubber bushes shall be provided to the bottom of legs of almirah.certificates : iso 9001 and bis/notified ce supplying and fixing of pre-painted galvalume trapezoidal profile roofing sheets with 0.50mm thickness, coating: alu-zinc coating az150 gsm. tensile strength: 550 mpa. paint coating: regular modified polyester painting. painting thickness (top): 18 to 20 microns, (bottom): 5 to 7 microns. sheet width: 1.020, length: maximum 12 meters with regular range colours fixed with g.i ‘j’ bolts & nuts 8 mm dia with bitumen & g.i limpet washers filled with white lead & including a coat of approved steel primer and two coats of approved paint on over lapping of sheets complete (up to a pitch of 600) etc., complete, excluding the cost of purlins, rafters, trusses including cost and conveyance of all materials , labour charges , etc., complete for finished item of work in all floors. supplying and fixing of ms doors, grill to windows / in open court yards using ms angles, flat, square bars including cost and conveyance of all materials, cutting, bending, welding, all operational charges, labour charges, etc., complete for finished item of work. white washing two coats with white cement to ceiling to give an even shade after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials including cost of all materials , labour charges and incidental such as scaffolding , lift charges etc., ..complete for finished item of work in all floors. supply & application of one coat water based cement primer of interior grade i and two coats of acrylic emulsion paint having voc (volatile organic compound) content less than 50 grams/litre for internal walls including cost and conveyance of all materials to site, incidental, operational and all labour charges etc.,..complete for finished item of work in all floors. for first floor supply & application of one coat water based cement primer of exterior grade ii and two coats of acrylic exterior emulsion paint having voc (volatile organic compound) content less than 50 grams/litre for exterior walls including cost and conveyance of all materials to site, incidental, operational and all labour charges etc.,..complete for finished item of work in all floors. painting to new wood work and flush shutters with lappam finish , over a primary coat and painting two coats of synthetic enamel paint grade-i voc (volatile organic compound) content less than 50 grams/litre of approved shade including cost and conveyance of all materials to site cost of primer coat and all labour charges etc. complete including applying sand paper on lappam coats for neat finish ..complete in all floors (apss no.1200, 1207 & 1211). for first floor construction of granular sub-base by providing hbg material confirming to grading - iii of mort & h table 400-2 including cost and conveyance of all material to work site and spreading in uniform layers with motor grader or by approved means, on prepared surface mixing by mix place method with rotavator/ approved means, at omc and compacting with vibratory roller to achieve the desired density etc., complete for finished item of work as per mort& h specification 401 (4th revision) and as directed by the engineer- in - charge including cost and conveyance of all materials , labour charges , ..etc., complete for finished item of work (payment will be made based on levels for finished item of work construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per clause 1501.2.2 m 30 (grade), coarse and fine aggregates conforming to is : 383, maximum in a concrete mixer of not less than 0.2 cum capacity and appropeiate weigh batcher using approved mix design, laid in approved fixed side formwork ( laying and fixing of 125 mictron thick polythene film including levelling the formwork as per drawing), spreading the concrete with sholvels, rakes, compacted using needle, scareed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge / culvert and construction joints, admixtures as approved, curing of concrete slabs for 14- days, curing compound (where specified) and water finishing to lines and grade as per drawing and technical specification clause 1501 mord including cost and conveyance of all materials , labour charges , ..etc., complete for finished item of work. supplying and fixing of 4 (101.6mm) multi floor trap with jali - upvc/swr pipe fittings as per site requirements with standard practice for all floors including cost and conveyance of all materials to site, labour charges , ..etc., complete for finished item of work. supplying and fixing indian make flat back wash hand basin 1st quality conforming to is:2556-part-4:1972 of size 550mm x 400mm with 32 mm nominal size c.p. fitting with parallel pipe thread conforming to is:2963-1979 and fitted with 15 mm nominal bore chromium plated pillar tap of 1st quality indian make heavy duty complete with standard ci brackets including wooden blocks ,1 no.12.70mm pvc connection with brass union nuts cp coated , angle stop cock 12.70mm dia. first quality indian make heavy duty, 31.75mm dia. pvc flexible waste pipe 914.4mm length of 1st quality including cost and conveyance of all materials to site, labour charges , ..for finished item of work supplying and fixing european water closet of 1st quality conforming to is:2556-part-2-1973 of white glazed with s trap,supplying and fixing best indian make plastic seat and lid for european water closets with rubber or plastic buffers as per is 2548-1996 and 10 litres capacity single flush pvc low level cistern with internal components and fixed using required size of nails and screws, angle stop cock 12.70mm dia. first quality indian make heavy duty, 12mm pvc connections with brass union nuts cp coated including cost and conveyance of all materials to site, ..etc., complete for finished item of work for all floors. supplying and fixing of stainless steel sink of size 508.00mm x 457.2mm x 203.20mm, 1mm thick of indian make fixed on cantilever brackets including supply and fixing 31.75mm c.p. waste coupling, 31.75 mm dia pvc flexible waste pipe of 914.4 mm length of ist quality ncluding chiselling brick masonry wall and making good & restoring to original surfaces , ..complete for finished item of work in all floors. supplying and fixing np soap dish heavy type of approved make isi quality with np screws etc., complete including cost and conveyance of all materials, labour charges for fixing , ..for finished item of work in all floors supplying and fixing tv shape mirror with plastic frame of size 609.6mm x 457.2mm , plywood back with np screws 1st quality including cost and conveyance of all materials, labour charges , ..for finished item of work in all floors. supplying and fixing of 25.4mm dia , 609.6mm long aluminium anodized towel rods with brackets and aluminium screws including cost and conveyance of all materials, labour charges , ..for finished item of work. supplying and fixing np bib taps of size 12.70mm dia of indian make heavy duty (short body) as approved by the engineer-in-charge including cost and conveyance of all materials, labour charges , ..complete for finished item of work in all floors. supplying and fixing np bib taps of size 12.70mm dia of indian make heavy duty (long body) as approved by the engineer-in-charge including cost and conveyance of all materials, labour charges , ..complete for finished item of work in all floors. supplying and fixing of swr pvc pipes (prince/sudhakar/kisan/supreme or any isi brand) 4 kg/sq.cm. and fixing all special such as plain bends, off sets, door bends, single junctions, double junctions as per site requirement, fixing with pvc clamps if necessary with required number of bombay nails including cost and conveyance of all materials to site, labour charges, ..complete for finished item of work at all floor levels. (apss no. 1302 1319 & 1326) for 75mm dia supplying and fixing of swr pvc pipes (prince/sudhakar/kisan/supreme or any isi brand) 4 kg/sq.cm. and fixing all special such as plain bends, off sets, door bends, single junctions, double junctions as per site requirement, fixing with pvc clamps if necessary with required number of bombay nails including cost and conveyance of all materials to site, labour charges, ..complete for finished item of work at all floor levels. (apss no. 1302 1319 & 1326) for 110mm dia supply and fixing of ashirvad/ ajay/ astral flowguard or equivalent cpvc pipes and fittings sdr 11 to meet the requirement of astm-d 2846 and are produced in cts (copper tube sizes 1/2 to 2) for hot and cold water (is 15778:2007) including cost and conveyance of all materials to site, labour charges for fixing, ..complete for finished item of work at all floor levels. for 15.90mm od pipe supply and fixing of ashirvad/ ajay/ astral flowguard or equivalent cpvc pipes and fittings sdr 11 to meet the requirement of astm-d 2846 and are produced in cts (copper tube sizes 1/2 to 2) for hot and cold water (is 15778:2007) including cost and conveyance of all materials to site, labour charges for fixing, ..complete for finished item of work at all floor levels. for 22.20mm od pipe supply and fixing of ashirvad/ ajay/ astral flowguard or equivalent cpvc pipes and fittings sdr 11 to meet the requirement of astm-d 2846 and are produced in cts (copper tube sizes 1/2 to 2) for hot and cold water (is 15778:2007) including cost and conveyance of all materials to site, labour charges for fixing, ..complete for finished item of work at all floor levels. for 28.60mm od pipe supplying and fixing gunmetal gate ( gm peet ) valve as per is-778 class - i , indian make heavy type including cost and conveyance of all materials , labour charges , ..complete for finished item of work. for 15mm nominal bore supplying and fixing gunmetal gate ( gm peet ) valve as per is-778 class - i , indian make heavy type including cost and conveyance of all materials , labour charges , ..complete for finished item of work. for 20mm nominal bore supplying and fixing gunmetal gate ( gm peet ) valve as per is-778 class - i , indian make heavy type including cost and conveyance of all materials , labour charges , ..complete for finished item of work. for 25mm nominal bore supply and fixing of 25mm outer dia (1.60 to 1.80)mm thicknes medium grade with is:9537 part 3 frls rigid surface p.v.c. pipe (isi marked) on wall with all required pvc junction boxes confirms to is : 3419 and all accessories fixing on chromium plated metallic base saddles for run of mains including all labour charges etc., complete. including all labour charges etc., complete. makes: precision/universal& marudhar/vip / goldmedal / million plast / gm / sudhakar /polycab/anchor/ polyline/ orbit/akg/beljin/vasavi/dec supply and fixing of of 16a/6a, 2 in one, modular type power socket outlet with 16a switch (isi marked) modular type and 2 no of 6a modular type sockets with 6a modular type (isi marked) switch control with front cover plate on existing modular switch box including all labour charges, giving all connections etc., complete with following configurations1) 16a socket - 2 no2) 16a switch - 2 no3) 6a socket - 2 no. 4) 6a switch - 2 no makes:legrand(myrius/lyncus)/schneider(clipsal x/ livia ab)/ crabtree (murano/athena)/lauritz knudsen-englaze (formerly l&t)/ gm-(four-five)/goldmedal(gifa)/million (m-vee)/anchor (roma plus)/precision(series7)/honeywell(blenzepro) supply and run of 3 of 2.5 sq.mm (phase neutral and earth) frls / frlsh / hffr / zhfr p.v.c. insulated 1100v grade as per is : 694 / 1990 specification flexible copper cable in existing ms conduit pipe for individual ligting circuits including labour charges etc., complete as required for switch boards.makes: finolex / rr kabel / havells/finecab/kei/polycab/gloster/goldmedal/gm/ fortune arrt/anchor/million/ apar(anushakthi) supply and 3 runs of 4.0 sq mm (phase neutral and earth) frls / frlsh / hffr / zhfr p.v.c. insulated 1100v grade as per is : 694 / 1990 specification flexible copper cable in existing conduit pipe for run of mains including labour charges etc., complete as required including labour charges for 16a sockets.makes: finolex /rrkabel/havells/finecab/kei/polycab/gloster/goldmedal/gm/ fortunearrt/anchor/million/ apar(anushakthi) supply & run of 5 of 10.0 sqmm (phases, neutral and earth) frls / frlsh / hffr / zhfr p.v.c. insulated 1100v grade as per is : 694 / 1990 specification flexible copper cable in the existing conduict pipe for run of mains from power panel board to tpn dbs with pin type lugs and connections etc., complete. [for pdbs] makes: finolex / rr kabel / havells/finecab/kei/polycab/gloster/goldmedal/gm/ fortune arrt/anchor/million/ apar(anushakthi) supply and fixing of tpn 4 way distribution board with ip-43 protection and as per is 8623; is 13032; iec 61439-3, (8+12 module) with provision to accommodate the elcb incomer and suitable for single pole outgoing mcbs in sheet steel enclosure with 63a, 10 ka breaking capacity c curve 4 pole mcb as incomer and 12 no of 6 to 32a, single pole, 10 ka breaking capacity c curve mcbs as outgoings including making connections etc., complete on wall. (lighting db). makes: legrand (ekinox 3) / schneider-a9/hager -novello+/ seimens/havells stadx/ lauritz knudsen (formerly l&t)-newrange/indo asian-opti pro/ hpl (techno)/ anchor (uno plus) supply and fixing of single phase db in sheet steel enclosure as per is 8623; is 13032; iec 61439-3 with metalic plug and socket with 1 no. 20/32a,10ka c curve spmcb control including labour charges and giving connections etc., complete concealed in wall. makes for dbs: legrand(ekinox 3) / schneider-acti9/hager-novello+/seimens/l&t-newrange and makes for mcbs: legrand-dx3 / schneider-acti9/hager-h3/ siemens-5sx4/ l&t-au . supply and fixing of 20-24w, not less than 1100mm length led batten light with extruded alluminium / crca housing and polycarbonate cover, input voltage ac 220 - 260 volts with pf>0.9, surge protection: 2kv, thd<15%, with high power leds having efficacy of ≥ 120 lumens / watt with inbuilt and replacable driver with earth connection brought outside and frosted cover cct: 3000k - 5700k, minimum cri>70 etc., complete including fixing on wall / ceiling with pvc/tw round blocks with all accessories including giving connections and all labour charges etc., complete with 5 years warranty.make: a) luminaire make : phillips / ge- venture / crompton / wipro / bajaj / havells / halonix/jaquar/hpl/gm / greenlites / gold medal/eveready// rhino/panasonicb) led make : philips lumileds / cree / nichia / osram / samsung/ everlight supply and transportation of 48 (1200mm) sweep star rated ceiling fan , with double ball bearings, air delivery more than 200 cubic meter/min but without regulator.makes: crompton (hs plus/hs) / havells (es plus/ss390es) /orient energy star/ halonix(zephyr)/polycab(synergy 50 isi) / g.m. (air wave premium)/bajaj-edge/arcline (glacier) supply, transportation, installation, testing and commissioning of the following inverter model cool type split ac unit with high wall mounted single split indoor unit and outdoor condencing unit hermetically sealed compressor suitable for operation on 230v, 50hz, 1phase ac supply capable of performing heat cool dehumidifying air circulating and filtering with cooling and condensing units with 3 mts of copper piping, insulation kit and 4 mts of 4 core copper flexible chord with cordless remote control etc., dual barrier coating in order to protect coil form oxidigation 1.5 tr 5 star capable of delivering 18000 btu/hr and above with operating on refrigerant r-32/ r-410a, cop not less than 4.5. makes: / blue star / daikin / hitachi/carrier / lg/lloyd (prevailing models in the market). supply, fabrication of 1set ms bracket suitable for fixing out door unit of split ac unit. supply and fixing of copper pipes of different dia and thickness for distribution, half drawn, tempered, seamless, phosphorous deoxidized, non arsenic and decreased confirming to bs 2871-1971 part-1 (table-x) and the chemical compositions shall be as per bs 6017 of 1981 table-2 with lloyd test certification, including cost and conveyance of pipes, cost of necessary specials made of copper and suitable for a steam working pressure of 17 bar and should confirm to bs 864 with specially made for brazed socket type connections, including taxes, transportation charges including laying and jointing, testing, commissioning and all other labour charges etc. complete for finished item of work. make: ibp conex / maxflow. for 12mm o.d x 0.7 mm supply and fixing of copper pipes of different dia and thickness for distribution, half drawn, tempered, seamless, phosphorous deoxidized, non arsenic and decreased confirming to bs 2871-1971 part-1 (table-x) and the chemical compositions shall be as per bs 6017 of 1981 table-2 with lloyd test certification, including cost and conveyance of pipes, cost of necessary specials made of copper and suitable for a steam working pressure of 17 bar and should confirm to bs 864 with specially made for brazed socket type connections, including taxes, transportation charges including laying and jointing, testing, commissioning and all other labour charges etc. complete for finished item of work. make: ibp conex / maxflow. for 15mm o.d x0.9mm supply and fixing of copper pipes of different dia and thickness for distribution, half drawn, tempered, seamless, phosphorous deoxidized, non arsenic and decreased confirming to bs 2871-1971 part-1 (table-x) and the chemical compositions shall be as per bs 6017 of 1981 table-2 with lloyd test certification, including cost and conveyance of pipes, cost of necessary specials made of copper and suitable for a steam working pressure of 17 bar and should confirm to bs 864 with specially made for brazed socket type connections, including taxes, transportation charges including laying and jointing, testing, commissioning and all other labour charges etc. complete for finished item of work. make: ibp conex / maxflow. for 22mm o.d x0.9mm supply and fixing of isolation valves with necessary brass end fittings designed for a working pressure of 300 psi / 27 inc. hg. vacuum, non ferrous, non lubricated with 90 degrees turn, hand lever operated of standard make of valves including cost and conveyance of all materials, taxes, transportation charges, fixing charges and testing charges and all labour charges etc. complete for finished item of work. make: ibp conex / maxflow for 15 mm valves (1/2) supply and fixing of oxygen flow meters with humidifier bottles.makes: aktiv technologies// atlas capco/ draeger medical/ / airox technologies / aastha medical technologies/ gmp technical solutions / medicare gas pipe line/mediline engineers supply and fixing gas outlet points for oxygen / air / vaccum with s brackets, self ceiling bross valves / din type outlets with nut and cap and it shuld be 100% self sealing type , so that at the time of removal of probe, it shuld stop gas flow automatically, out let shuld be single hand insertion, non inter changeable for specific gas, it should accept only correct medical gas adapter. with down tube of the specific gas should be brazed with brass bracket of the outlet, there after brass bracket should be fixed in wall with the help of the steel screw, with self sealing valve which should be screwed with the front portion of brass bracket and there after it should be covered by plastic cover duly colour coded as per specific gas, design of outlet should be such that it can be installed vertically on wall, horizontally on iccu panel and also vertical to fit in pendants including cost and conveyance of all materials, errection charges, commissioning charges and all other labour charges etc, complete for finished item of work. makes: aktiv technologies// atlas capco/ draeger medical/ / airox technologies / aastha medical technologies/ gmp technical solutions / medicare gas pipe line/mediline engineers