BRR:7520168 Material Supply For Annual Construction At.Gp. Shivapur , Construction Materials , Metal 80 Mm , Metal 40 Mm , Metal 20 Mm , Metal 12 Mm , Barbed Wire / Fenshing Wire , Sand , Murum , Cement 53 Grade Isi Mark , Road Rollar Rent , Water Tankar , Sittl 6Mm , Still 8 Mm , Still 10 Mm , Still 12 Mm , Still 16 Mm , Still 20 Mm , Centring Tar , Bricks (Red) , Bricks (Cement) , Mixer Machine , Tiles Ceramic , Tiles Vitrified , Tiles Polished Chequered , Iron Door With Frame & Palla , Cement Door Palla , Cement Door Frame , Iron Sheet Of 0.50 Mm , Islb Angle , Iron Angle , Iron Window Grill& Palla , Plastic Water Tank (1000 Lit.) , Plastic Water Tank (500 Lit.) , Distemper , Jcb , Damber/ Tar Oil , Alluminium Sliding Window , Cement Pipe 150 Mm With Collar , Cement Pipe 250 Mm With Collar , Cement Pipe 300 Mm With Collar , Cement Pipe 450 Mm With Collar , Cement Pipe 600 Mm With Collar , Cement Pipe 800 Mm With Collar , Cement Pipe 900 Mm With Collar , Khadanga , Centring Plate Rent , Information Board (0.90X0.60)Cm , Kota Stone , Vibrating Machine , Ms Grill , Snowsem , Cement Waterproof Paint , Oil Paint , Tarpipne , Wc Pan (Toilet Seat) , Pvc Pipe 1/2 Inch , Pvc Pipe 3/4 Inch , Pvc Pipe 1 Inch , Pvc Tee / Elbo , Paiwar Block , Rubble

BRR:7521957 The Supply Of Primary Food Grade Packing Materials And Corrugated Cartons For The Use Of Milma Kozhikode Dairy The Supply Of Primary Food Grade Packing Materials And Corrugated Cartons For The Use Of Milma Kozhikode Dairy Peringolam Tender Period 01/12/2023 To 30/11/2024 , Paper Cups , 50 Ml Paper Cup And Lid Ice Cream (50 Ml +/-2 Ml Of Top Overflow Level) Paper Cup With West Coast Or Equivalent Paper Board Above 185 Gsm And Lid With White Back Above 200 Gsm. Inside Bottom To Rim Of Cup Height 30+/-1 Mm. Exterior Bottom To Rim Of Cup 40Mm+/-1Mm Bottom Diameter 50+/- 1Mm.Diameter At Rim Of The Cup 60+/-1Mm.Paper Cup With Food Grade Quality Is 10177(1998) Water Proof Pe Coated Material. Multicolor As Per Our Artwork. Paper Quality Shall Comply With Is 1776.1961.Samples Will Be Available In Kozhikode Dairy For Further Clarification , Corrugated Boxes , 50 Ml Single Colour Corrugated Box 3 Ply Corrugated Box To Pack 50 Ml Ice Cream Cups Hwc Duplex Board 200 Gsm ,120 Gsm 18 Bf Kraft With Single Colour Printing. Four 200 Gsm Partition Plates (18X12 Cm) Should Be Supplied With Each Box Size 20.0 L X 13.0 B X 13.0 H Cm-E Flute With Good Quality Gum And Carton Formation By Pasting Only (No Stapler).2 Holes With Size 35 Mm Dia At Each Side Should Be Provided For Air Passage. Cartons With Cutting Piece Of Hole Will Be Rejected. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Delite Single Colour Corrugated Box 3 Ply Corrugated Box To Pack 60 Ml Delite Ice Cream Cups Hwc Duplex Board 200 Gsm ,120 Gsm 18 Bf Kraft With Single Colour Printing. 3 Ply Corrugated Board With Size 28X8 Cm With 8 Holes Should Be Supplied With Each Box Size 26.0 L X 13.0 B X 10 H Cm-E Flute With Good Quality Gum And Carton Formation By Pasting Only (No Stapler).4 Holes With Size 25 Mm Dia At Each Side Of The Box Should Be Provided For Air Passage. Cartons With Cutting Piece Of Hole Will Be Rejected. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Chocobar Master Carton Corrugated Box 3 Ply Corrugated Box To Pack 35/60 Ml Choco Bar Ice Cream Hwc Duplex Board 200 Gsm , 120 Gsm 18 Bf Kraft With Single Colour Printing. Size 24.5 L X 15.0 B X 10.2 H Cm-E Flute With Good Quality Gum And Carton Formation By Pasting Only (No Stapler).4 Holes With Size 25 Mm Dia At Each Side Should Be Provided For Air Passage.Cartons With Cutting Piece Of Hole Will Be Rejected. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Kulfi Stick Master Carton 3 Ply Corrugated Box Hwc Duplex Board 200Gsm.120 Gsm 18 Bf Kraft Withsingle Colour Printing. Size 24.5 L X 15.0 B X 10.2 H Cm-E Flute With Good Quality Gum And Carton Formation By Pasting Only (No Stapler).4 Holes With Size 25 Mm Dia At Each Side Should Be Provided For Air Passage.Cartons With Cutting Piece Of Hole Will Be Rejected. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Tora Tora Corrugated Box 3 Ply Corrugated Box To Pack 100 Ml Cone Ice Cream Cups,200 Gsm Hwc Duplex Board 120Gsm 18 Bf Kraft With Single Colour Printing. Size 16.0 L X 13.0 B X 13.0 H Cm-E Flute With Good Quality Gum And Carton Formation By Pasting Only (No Stapler).4 Holes With Size 25 Mm Dia At Each Side Should Be Provided For Air Passage. Cartons With Cutting Piece Of Hole Will Be Rejected. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Honey Splashcarton Corrugated Box 3 Ply Corrugated Box To Pack 100 Ml Ice Cream Honey Splash Cups, 200 Gsm Hwc Duplex Board 120Gsm 18 Bf Kraft With Single Colour Printing. Size 23.5 L X 15.5 B X 7.5 H Cm-E Flute With Good Quality Gum And Carton Formation By Pasting Only (No Stapler).4 Holes With Size 35 Mm Dia At Each Side Of The Box Should Be Provided For Air Passage.Cartons With Cutting Piece Of Hole Will Be Rejected. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Mini Tora Corrugated Box 3 Ply Corrugated Box To Pack 45 Ml Cone Ice Cream Cups. 200 Gsm Hwc Duplex Board 120Gsm 18 Bf Kraft With Single Colour Printing. Size 21.0 L X 14.0 B X 10.0 H Cm-E Flute With Good Quality Gum And Carton Formation By Pasting Only (No Stapler).4 Holes With Size 25 Mm Dia At Each Side Should Be Provided For Air Passage. Cartons With Cutting Piece Of Hole Will Be Rejected. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Medium Cone Carton 3 Ply Corrugated Box To Pack 60 Ml Cone Ice Cream 200 Gsm Hwc Duplex Board 120Gsm 18 Bf Kraft With Single Colour Printing. Size 21.5L X 14.5 Wx 10.5 Cm H-E Flute With Good Quality Gumand Carton Formation By Pasting Only (No Stapler).4 Holes With Size 25 Mm Dia At Each Side Should Be Provided For Air Passage. Cartons With Cutting Piece Of Hole Will Be Rejected. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Fun Bar Master 3 Ply Corrugated Box To Pack 35/60 Ml Fun Bar / Twin Bar Ice Cream Bars 200 Gsm Hwc Duplex Board 120Gsm 18 Bf Kraft With Single Colour Printing. Size 24.5 L X 15.0 B X 10.2 H Cm-E Flute With Good Quality Gum And Carton Formation By Pasting Only (No Stapler).4 Holes With Size 25 Mm Dia At Each Side Should Be Provided For Air Passage. Cartons With Cutting Piece Of Hole Will Be Rejected. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Sugar Free Carton 3 Ply Corrugated Box To Pack 90 Ml Tub Ice Cream, 200 Gsm Hwc Duplex Board 120Gsm 18 Bf Kraft With Single Colour Printing. Size 14.5 L X 14.5 B X 15.8 H Cm-E Flute With Good Quality Gum And Carton Formation By Pasting Only (No Stapler).4 Holes With Size 25 Mm Dia At Each Side Should Be Provided For Air Passage.Cartons With Cutting Piece Of Hole Will Be Rejected. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Cartons For Cup Curd - 400Gm 3 Ply Corrugated Box To Pack 400 Ml Cup Curd, 250Gsm ,Hwc Duplex Board And Inner 140 Gsm 18 Bf Kraft With Single Colour Printing . One 230 Gsm Partition Plates (40X19.5 Cm) With 6 Holes Of 7 Cm Dia Should Be Supplied With Each Box Size 29.0 L X 20.0 B X 11.0 H Cm-E Flute With Good Quality Gum And Carton Formation By Pasting Only (No Stapler).4 Holes With Size 25 Mm Dia At Each Side Should Be Provided For Air Passage. Cartons With Cutting Piece Of Hole Will Be Rejected. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Cartons For Cup Curd - 200Gm 3 Ply Corrugated Box To Pack 200 Ml Cup Curd, 250Gsm ,Hwc Duplex Board And Inner 140 Gsm 18 Bf Kraft With Single Colour Printing . One 230 Gsm Partition Plates (18X18 Cm) Should Be Supplied With Each Box Size 19.5 L X 19.5 B X 17.0 H Cm-E Flute With Good Quality Gum And Carton Formation By Pasting Only (No Stapler).4 Holes With Size 25 Mm Dia At Each Side Should Be Provided For Air Passage. Cartons With Cutting Piece Of Hole Will Be Rejected. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Cartons For Cup Curd - 80Gm 3 Ply Corrugated Box To Pack 80 Ml Cup Curd, 250Gsm ,Hwc Duplex Board And Inner 140 Gsm 18 Bf Kraft With Single Colour Printing . Three 230 Gsm Partition Plates (20X12 Cm) Should Be Supplied With Each Box Size 21.0 L X 14.0 B X 15.0 H Cm-E Flute With Good Quality Gum And Carton Formation By Pasting Only (No Stapler).4 Holes With Size 35 Mm Dia At Each Side Should Be Provided For Air Passage. Cartons With Cutting Piece Of Hole Will Be Rejected. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Cartons For Cup Curd - 80Gm/Yoghurt 3 Ply Corrugated Box To Pack 80 Ml Cup Curd, 150Gsm ,Hwc Duplex Board And Inner 140 Gsm 18 Bf Kraft With Single Printing . Three 230 Gsm Partition Plates (20X12 Cm)Should Be Supplied With Each Box Size 21.0 L X 14.0 B X 15.0 H Cm-E Flute With Good Quality Gum And Carton Formation By Pasting Only (No Stapler).4 Holes With Size 35 Mm Dia At Each Side Should Be Provided For Air Passage. Cartons With Cutting Piece Of Hole Will Be Rejected. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Cartons For Cup Curd - 40Gm 3 Ply Corrugated Box To Pack 40 Ml Cup Curd Cups, Full Craft 140 Gsm 18 Bf Kraft With Single Colour Printing . Four 230 Gsm Partition Plates (18X11cm)Should Be Supplied With Each Box Size 20.5 L X 13.0 B X 14.0 H Cm-E Flute With Good Quality Gum And Carton Formation By Pasting Only (No Stapler).2 Holes With Size 35 Mm Dia At Each Side Should Be Provided For Air Passage. Cartons With Cutting Piece Of Hole Will Be Rejected. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Cartons For Kattathyru 3 Ply Corrugated Boxes To Pack 400 Gm Kattathyru, Full Craft 1 With Single Colour Printing . Each Box Size 29 Cm L X 19.5 Cmb X11.0 H Cm-E Flute With Good Quality Gum And Carton Formation By Pasting Only (No Stapler).2 Holes With Size 35 Mm Dia At Each Side Should Be Provided For Air Passage. Cartons With Cutting Piece Of Hole Will Be Rejected. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Ball Strawberry 100 Ml (Ice Cream) Food Grade Strawberry Shaped Ice Cream Ball With Lid, Printed 75 Ml With Milma Artwork And Vegetarian Logo, Capacity 100Ml +/- 2Ml, Weight Not Less Than Per Ball +/- 2Gms Should Be Supplied Polyethylene Lined Bundle/Back And Weight Of Bundle Should Be Mentioned. The Ball Colour Should Contrast With The Print Colour Used. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Ball Mango- 100 Ml (Ice Cream) Food Grade, Mango Shaped Ice Cream Ball, Printed 100 Ml With Milma Artwork And Vegetarian Logo. Minimum Weight Of Ball=Above 11 Gm/Ball+/-2Gm. Ball Should Be Supplied In Polythene Lined Bundle/Bag With Lids And The Weight Of Bundle Should Be Mentioned. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Ball Kulfi 100 Ml (Ice Cream) Food Grade, Mudka Shape, Single Colour Printed With Milma Artwork And Vegetarian Logo. Weight Of Ball Should Be 12Gm +/- 2 Gm. Ball Should Be Supplied Polythene Lined Bundle/Bag With Lids And The Weight Of Bundle Should Be Mentioned. The Print Colour Should Contrast With The Colour Of The Cup. Samples Will Be Available In Kozhikode Dairy For Further Clarification , 50 Ml Ball (Ice Cream) Material Hdpe Food Grade In Golden Yellow Colour For Balls And Various Colours For Lids.Volume 60 Ml Printing ;Screen Printing On Both Sides As Per Art Work By Using Food Grade Quality Of Ink , Tub, Lid And Other Pp Items , 350 Ml Tub With Lid (Food Grade) Ice Cream Tub With Lid, Cup Shall Be Printed 250 Ml With Milma Art Work (Capacity 350 Ml +/-2Ml At Top Over Flow Level). Weight Of Cup 10 G+/-1G And Lid 4.5G+/-1G. The Material Shall Be Food Grade Material. The Material Shall Withstand -20Oc Storage Temperature And Shall Not Be Brittle. The Lids Should Be Easily Positioned And Intact. Samples Will Be Available In Kozhikode Dairy For Further Clarification , 60 Ml Delite Tub With Lid (Food Grade) 60 Ml Milma Delight Ice Cream Cup (Capacity 60 Ml +/- 2Ml) 4 Colour Print And Single Colour Lid (Sundae Type). Cup Shall Be Printed With Milma Art Work. Weight 10.0 Gms With Lid+/-0.5 Gm. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Iml Casatta 75 Ml Tub With Lid (Food Grade) Arch Type, Size 8.4 Cm Radius, 13.0 Cm Length, 16 Gm Weight With Our Approved Iml Labelling. The Material Shall Be Food Grade Material. The Material Shall Withstand -20°C Storage Temperature And Shall Not Be Brittle. The Lids Should Be Easily Positioned And Intact. Samples Will Be Available In Kozhikode Dairyfor Further Clarification , 1000 Ml Euro Iml Tub (Food Grade) Poly Propylene Round Tapered Shape Container With Approved Iml Labelling With Container Top Outer Diameter 130+/-1Mm, Bottom Outer Diameter 108+/-1 Mm. Flat Round Lid With Iml Labelling Having Dia 126+/-1 Mm Has To Be Supplied Along With Tub. Minimum Weight Of The Container Along With Lid 47G. The Container &Lid Should Be Resistant To Cracking In The Deep Freeze Temp Of -30°C Both During Storage& Transportation. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Iml 500Ml (All Flavours) (Foodgrade) Container: Material Pp-Bassel ,Colour White Opaque ,Wt(Gm) 25 ,Total Wt In Gms 30.6Gm,Neck Opening Dia(Mm)Od=98Mm/Id=89Mm.Neck Height (Mm) 19M,Max.Outer Dia (Mm) 99Mm,,Max.Height In Mm 112.5Mm ,Max.Height Lid In Mm 113.5Mm,Volume Ml(Overflow)590. Lid: Material Pp-Bassel, Colour White Opaque, Wt (Gm) 5.6, Max.Outer Dia (Mm)96, Max.Height In Mm 9 Labeling : In Mould As Per Our Approved Design Quality: The Container &Lid Should Be Resistant To Cracking In The Deep Freeze Temp Of -30°C Both During Storage& Transportation , Iml 1Kg Curd (Food Grade) Poly Propylene Round Shape Container With Approved Iml Labelling With Container Outer Diameter 131±0.5Mm, Inner Diameter 122±0.5 Mm. Flat Round Lid With Iml Labelling Having Dia 130±0.5 Mm Has To Be Supplied Along With Tub. Minimum Weight Of The Container Along With Lid 55.1G±5%. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Honey Splash Tub (100 Ml) (Food Grade) Container Outer Dia 74.1+ /- 0.5Mm,Container Inner Dia 68+/-0.5Mm,Container Shape Round,Shape Of The Lid Dome Shape ,Lid Dia Mm 78+/0.5Mm,Ht Of Container With Lid 68+/-0.5Mm,Cup Wt(Gms)5.01+/- 5%,Lid Weight(Gms)4.50+/-5%,Material Polypropylene(Sryrene Based+Additive),Vol Till Fill Point 100Ml,Packing/Carton 1000Nos.Of Glass&Lid , Sugar Free Tub 90 Ml (Food Grade) Container Outer Dia 69+ /- 0.5Mm,Container Inner Dia 61+/-0.5Mm,Container Shape Round,Flat Lid With Dia Mm 67+/-0.5Mm, Ht Of Container With Lid 53+/-0.5Mm,Cup Wt(Gms)8.06+/- 5%,Lid Weight(Gms) 2.61+/-5%,Material Polypropylene,Vol Till Fill Point 100Ml,Packing/Carton 1 2000Nos.Of Tub & Lid , 125Ml Iml Tub (All Flavours/Food Grade) Container Outer Dia 68+ /- 0.5Mm,Container Inner Dia 61+/-0.5Mm,Container Shape Round,Flat Lid With Dia Mm 67+/-0.5Mm, Ht Of Container With Lid 68+/-0.5Mm, Bottom Diameter 54+/-0.5Mm. Cup Wt(Gms) 9.02+ /-5%,Lid Weight(Gms) 2.6+/-5%,Material Polypropylene,Vol Till Fill Point 175Ml,Packing/Carton 1 2000Nos.Of Tub & Lid , Kattathyru Bottle With Lid 500Gm Pet Jar Of Wt 29.4Gmoverflow Volume 585Gm,74Mm Dia With Thread Without Thread 71Mm And Total Height 111Mm , Cup For Curd 400Gm (Food Grade) Hips Curd Cups 95 Mm Dia With 7 Color Printing, Weight 12Gram. , Cup For Curd 200Gm (Food Grade) Hips Curd Cups 95 Mm Dia With 7 Color Printing, Weight 6 Gram. , Cup For Curd 80 Gm (Food Grade) Hips Curd Cups 69 Mm Dia With 7 Color Printing, Weight 5 Gram. , Yoghurt Cup- 80Gm (Food Grade) Hips Cups 69 Mm Dia With 7 Color Printing, Weight 5 Gram. , Cup For Curd 40 Gm (Food Grade) Hips Curd Cups 69 Mm Dia With 7 Color Printing, Weight 3 Gram. , Cup Curd Lid (Aluminium Foil) 400 Gm /200 Gm(95.5Mm Dia) 95Mm Dia 6 Color Printing,40 Micron, Material Sealable Hips , Yoghurt Foil (Food Grade) 69M M Dia 6 Color Printing,30 Micron, Material Sealable Hips , Cup Curd Lid ( Aluminium Foil) 80 Gm/ 40 Gm (69Mm Dia) 69Mm Dia 6 Colour Printing, 40 Micron, Material Sealable Hips , Kattathyru Bottle Lid 400Gm (Aluminium Plainfoil) 80Mm Dia Plane Aluminium Foil, 40 Micron, Material Sealable Hips , Duplex Cartons , 4000 Ml (All Flavours) Duplex Carton Duplex Cartons, Multi Colour Printing, Outer & Inner Side Food Grade Lamination (12 Mic), 400Gsm White Back Itc Or Equalent Board Size (22.5Lx8.5Bx10.5H) Cm Food Grade And Non Permeable. Samples Will Be Available In Kozhikode Dairy For Further Clarification , 2000 Ml (All Flavours) Duplex Carton Duplex Cartons, Multi Colour Printing, Outer & Inner Side Food Grade Lamination (12 Mic), 400Gsm White Back Itc Or Equalent Board Size (22.5Lx8.5Bx10.5H) Cm Food Grade And Non Permeable. Samples Will Be Available In Kozhikode Dairy For Further Clarification , 1250 Ml (All Flavours) Duplex Carton Duplex Cartons, Multi Colour Printing,Outer & Inner Side Food Grade Lamination (12 Mic), 400Gsm White Back Itc Or Equalent Board Size (9.5Lx6.5Bx24h) Cm Food Grade And Non Permeable. Samples Will Be Available In Kozhikode Dairy For Further Clarification , 750 Ml (All Flavours) Duplex Carton Duplex Cartons, Multi Colour Printing, Outer & Inner Side Food Grade Lamination (12 Mic), 350Gsm White Back Itc Or Equalent Board Size (20.0Lx05.0Bx7.5H) Cm Food Grade And Non Permeable. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Chocobar Duplex Carton Duplex Cartons, Multi Colour Printing, Outer And Inner Side Food Grade Lamination (12Mic, Popp), 280Gsm Duplex Board Grey Back (2Hx14lx5b Cm). Samples Will Be Available In Kozhikode Dairy For Further Clarification , Chotta Chocobar Duplex Carton Duplex Cartons, Multi Colour Printing, Outer And Inner Side Food Grade Lamination (12Mic, Popp), 280Gsm Duplex Board Grey Back (2Hx14lx5b Cm). Samples Will Be Available In Kozhikode Dairy For Further Clarification , Kulfi 100 Ml Duplex Carton Duplex Cartons, Multi Colour Printing, Outer & Inner Side Food Grade Lamination (12Mic), 300 Gsm Duplex Board Size (6.5Lx6.5Bx6.00Hcm) Food Grade And Non Permeable. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Kulfi Stick Duplex Carton Duplex Cartons, Multi Colour Printing, Outer And Inner Side Food Grade Lamination, Board Itc, 300Gsm Duplex. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Cone, Sleeve And Lid , Big Cone Sleeve With Lid (Food Grade) Multi Colour Printing On Aluminium Foil To Pack 100 Ml Cone. 16.5 Cm Length. Top Diameter 9.5 Cm Laminated Metalized Foil Paper With White Interiors As Per Approved Artwork. Multi Colour Print. Lids With Multi Colour Printing On White Back Poly Coated Paper 15 Micron Thick. Round Type 59 Mm Dia, 280 Gsm Thicknesses. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Big Rolled Cone Biscuit Rolled Cone Biscuit, Food Grade -Dry , Fresh, Size As Per Given Samples. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Big Rolled Cone +Sleeve+Lid(1 00 Ml) Multi Colour Printing On Aluminium Foil To Pack 100 Ml Cone. 16.5 Cm Length. Top Diameter 9.5 Cm Laminated Metalized Foil Paper With White Interiors As Per Approved Artwork. Multi Colour Print. Lids With Multi Colour Printing On White Back Poly Coated Paper 15 Micron Thick. Round Type 59Mm Dia, 280 Gsm Thickness. Food Grade Rolled Cone With Size To Fill 100 Ml Ice-Cream, Crispy, Dry, Sweet And Fresh. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Cone Sleeve(50 Ml)+Cone Lid For Mini Cone (Food Grade) Multi Colour Printing On Aluminium Foil To Pack 50 Ml Cone. 14 Cm Length. Top Diameter 8.0 Cm Laminated Metalized Foil Paper With White Interiors As Per Approved Artwork. Multi Colour Print. Lids With Multi Colour Printing On White Back Poly Coated Paper 15 Micron Thick. Round Type 4.7 Cm Dia, 280 Gsm Thickness. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Sugar Cone (50 Ml) For Mini Cone Sugar Wafer/ Rolled Cone Biscuit, Food Grade-Dry, Fresh, Size As Per Given Sample. The Item Should Be Quoted With Cost Of Sleeving, Sleeves Will Be Provided By Us. Quote Should Be Inclusive Of All, The Product Should Comply Is 7188-1989 Standard. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Medium Cone Sleeve With Lid Size- 150Mm, Paper- Alu; Coated Paper 100 Gsm(Food Grade), Printing- Multi Colour, Board- White Back Board 200 Gsm(Food Grade), Printing- Multi Colour, Polycoat- Inside. , Medium Cone Biscut (Food Grade) Length(Mm) – 95Mm, Weight(G) – 9G, Diameter(Mm) – 41Mm, Ingredients – Wheat Flour, Edible Vegetable Oil, Soya Lecithin Caramel, Sugar And Salt. , Spoons And Sticks , Wooden Stick With Printing- Small Size Birch Wood Stick Ab Grade Round Edge With Logo Printing Size 93 X 10 X 2 Mm To Use In Extrusion Line.(Food Grade) , Wooden Stick With Printing- Big Size Birch Wood Stick Ab Grade Round Edge With Logo Printing Size 114 X 10 X 2 Mm To Use In Extrusion Line.(Food Grade) , Wooden Spoon Premium 90Mm Length-90.00+Or- 1.00, Width- 17/11.00+Or-0.50 Thickness-1.35+Or-0.50, Bundled- Paper Band Condition- Clean And Normal Smell’ Shape- Spoon Normal, Spoon Should Be Food Grade And Wrapped In Printed One Side And Polycoated One Side Poster With Natural Itc 45 Gsm. , Wooden Spoon Premium 75 Mm Birch Wood Ab Grade Wooden Spoon With Food Grade Wood Size Of 75Mm Length, Free From Bitter Taste, Fungal Free, Smooth Finish And With Fine Edges. Spoon Should Be Wrapped In Printed One Side And Polycoated One Side Poster With Natural Itc 45 Gsm. , Packing Bags , Packing Bag For Ball, Kulfi 8*14.5 Inch Food Grade 90-95 Micron And Non Permeable. Minimum No .Per Kg Should Be Mentioned In The Tender/Po , Packing Bag For Chocobar, Mango Bar, Kucha (6.5(2+2)16 Inch Gazeyyed Bags 2(See Specimen). Food Grade 90-95 Micron And Non Permeable. Minimum No. Per Kg Should Be Mentioned In The Tender/Po , Packing Bag For Sip Up, Lolly, Cassatta 8*11.5 Inchfood Grade 90-95 Micronand Non Permeable Minimum No: Per Kg Should Be Mentioned In The Tender/Po , Stickers , 250 Ml (All Flavours) Sticker Multi Colour Printing, Round Type Size 11.0Cm Dia, Mirror Coat,70Gsm & 80Gsm, Release Paper, Gum Sheet Should Be Good Quality And Should Withstand 25*C At Deep Freezer And 6 Months Storage, Item Should Be The Supplied Flavour Wise Bundle In Poly Pouch Contains 200 Stickers. Samples Will Be Available In Kozhikode Dairy For Further Clarification , Sticker For Kattathyru Bottle -400Gm Multi Colour Printing Arch Type, 290Mm X 55Mm Samples Will Be Providing From Kozhikode Dairy Store , Flowwrap Film , Flow Wrap For Big Chocobar 12 Mic Polyester +25 Mic, Color Bopp Laminated Roll, Size.180/165 Mm Wide And 190Mm (Food Grade) , Flow Wrap For Chotta Chocobar 12 Mic Polyester +25 Mic, Color Bopp Laminated Roll, Size.180/165 Mm Wide And 190Mm (Food Grade) , Flow Wrap For Kucha Kucha Kulfi 12 Mic Polyester +25 Mic, Color Bopp Laminated Roll, Size.180/165 Mm Wide And 190Mm (Food Grade) , Flow Wrap For Fun Bar 12 Mic Polyester +25 Mic, Color Bopp Laminated Roll, Size.180/165 Mm Wide And 190Mm (Food Grade) , Flow Wrap For Twin Bar 12 Mic Polyester +25 Mic, Color Bopp Laminated Roll, Size.180/165 Mm Wide And 190Mm (Food Grade) , Sip Up Film , Film For Water Sip Up (Food Grade) Thickness : 65 Microns, Film Type: 3 Layer Transparent Ldpe Film Printing : 1 Color, Roll Weight: 6-7 Kgs Film Should Be Free From Pinholes, Streaks, Foreign Particles Organic Or Inorganic, Gauge Variation Bands And Undispersed Raw Material. The Film Should Have Even And Wrinkle Free Surface With No Visible Defects Such As Holes Tears Or Blisters. The Printing Shall Be Neat And Clean Without Any Defect. Ink For Printing Shall Conform To Is5931:1970. Winding Shall Be Uniform With Proper Tension Without Any Telescoping. The Reel Shall Be Packed In 3 Ply Corrugated Carton Or Stretch Wrap As May Be Suitable. , Film For Milk Lolly(Food Grade) Thickness : 65 Microns, Film Type: 3 Layer White Opaque Ldpe Film, Printing : 2 Colors, Roll Weight: 6-7 Kgs. Film Should Be Free From Pinholes, Streaks, Foreign Particles Organic Or Inorganic, Gauge Variation Bands And Undispersed Raw Material. The Film Should Have Even And Wrinkle Free Surface With No Visible Defects Such As Holes Tears Or Blisters. The Printing Shall Be Neat And Clean Without Any Defect. Ink For Printing Shall Conform To Is5931:1970. Winding Shall Be Uniform With Proper Tension Without Any Telescoping. The Reel Shall Be Packed In 3 Ply Corrugated Carton Or Stretch Wrap As May Be Suitable. , Film For Wing Lolly (Food Grade) Laminated Film Of 12 Micron Pet+40Micron Ldpe Film With Minimum Thickness Of 52Micron Free From Pinholes, Streaks, Foreign Particles Organic Or Inorganic, Gauge Variation Bands And Undispersed Raw Material. The Film Should Have Even And Wrinkle Free Surface With No Visible Defects Such As Holes Tears Or Blisters. Width Of The Film Should Be 80Mm And Diameter Shall Be 285Mm Including Core. Six Colour Printing As Per Artwork Approved By The Union, The Printing Shall Be Neat And Clean Without Any Defect. Ink For Printing Shall Conform To Is5931:1970. The Film Reel Shall Be Supplied With 75Mm Inner Diameter Paper Core Suitable For Mounting On Packing Machine. Winding Shall Be Uniform With Proper Tension Without Any Telescoping. The Reel Shall Be Packed In 3 Ply Corrugated Carton Or Stretch Wrap As May Be Suitable.

BRR:7521122 Tender For Annual Plan-Moonniyur Gp (2024-25) Pno:309 Parakkadavu Pattisseri Road In Ward No:11-Parakkadavu Pattisseri Road-General Civil Work; 1 Retarring 2 3.2:Preparation of Foundation for EmbankmentScarifying Existing Bituminous Surface to a Depth of 150 mm by Mechanical MeansScarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per Technical Specification Clause 301.4. 3 OD110420/2024-2025:Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade 4 4.9:Wet Mix MacadamProviding, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406.By Mechanical Means with 1 km lead 5 75.5.1.1pb:Prime Coat - Low porosity - With Packed Bitumen RatesProviding and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502 6 75.5.2.3pb:Tack Coat - With Packed Bitumen RatesProviding and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503. 7 75.5.11.1.A.2pb:Mix Seal Surfacing - Manual Means - Type A - Bitumen S-65 - Packed Bitumen RatesProviding, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type-B) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification Clause 509By Manual MeansType A(II) Bitumen (S-65)

BRR:7509642 Tender For Annual Plan-Projectno:375/25-Alungal Madathilthazam Road Renovation In Kodiyathur G.P-General Civil Work - Road Renovation 2 3.2:Preparation of Foundation for Embankment
Scarifying Existing Bituminous Surface to a Depth of 150 mm by Mechanical Means
Scarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per Technical Specification Clause 301.4. 3 4.9:Wet Mix Macadam
Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406.
By Mechanical Means with 1 km lead 4 75.5.1.1pb:Prime Coat - Low porosity - With Packed Bitumen Rates
Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502 5 75.5.2.3pb:Tack Coat - With Packed Bitumen Rates
Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503. 6 75.5.2.1pb:Tack Coat - With Packed Bitumen Rates
Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503. 7 75.5.5.A.1pb:Modified Penetration Macadam 50 mm thick using Bitumen S-65 - Packed Bitumen Rates
Construction of penetration macadam over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506. 8 75.5.5.B.2pb:Modified Penetration Macadam 75 mm thick using Bitumen S-65 - Packed Bitumen Rates
Construction of penetration macadam over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506. 9 75.5.11.1.A.2pb:Mix Seal Surfacing - Manual Means - Type A - Bitumen S-65 - Packed Bitumen Rates
Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type-B) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification Clause 509
By Manual Means
Type A
(II) Bitumen (S-65)

BRR:7520248 Tender For Repairs To Psb At Purjal Tq. Aundha - Removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete (Item No.46.19) 2 Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etc. complete. (Item No. 46.15) 3 Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) (Item No. 24.01) 4 Providing and fixing in position. (as per I.S.1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension 63.50 x 38.10 x 1.02 mm at weight 0.547 kg/Rmt. and window frame bottom track section 61.85 x 31.75 x 1.20 mm at weight 0.695 kg/Rmt. Top and side track section 61.85 x 31.75 x 1.30 mm at weight 0.659 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. And handle section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. and top section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc, complete. With colour Anodising with box. ( Item No. 39.37) 5 Providing and fixing solid core flush door shutter commercial in single leaf 32 mm thick without ventilator commercial type of exterior grade as per detailed drawings with wrought iron hold fast, stainless steel fixtures and fastenings and handles on both sides and finishing with oil painting 3 coats complete. (Item No. 39.10) 6 Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearingetc. complete. a) Flooring ( Item No. 33.40) 7 Providing and laying damp proof course 50 mm thick in M20 cement concrete layer and bitumen / using cement with waterproofing compound curing, formwork etc. complete.9 (Item No.31.01) 8 Providing and fixing mild steel grill work for windows, ventilators etc. 20 kg/sqm as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete. (Item No. 40.01) 9 Providing and fixing heavy duty inter locking concrete Rubber mould glossy paving blocks of 80 mm thickness of having a strength of 400 kg/Sq.cm. of approved quality and shape on a bed of crushed sand of 25 to 30 mm thick including skirting joints and cleaning etc.complete. (using 100% crushed sand) ( Item No. 33.54) 10 Providing and laying Cast in situ/Ready Mix cement concrete M-15 of trap/ granite/quartzite/gneiss metal for coping to plinth or parapet, moulded or chamfered as per drawing or as directed including steel centering, plywood/ steel formwork compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.) With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) ( Item No. 24.16) 11 Providingandfixingboarddisplayinginformation,suchasNameof work, Tender cost, Name of Contractor, Work completion and liability period etc, having rectangular shape of 1.20m x 0.90m size made out 18gauge(1.25mm)thickmildsteelsheetpaintedwithonecoatof Zinc chromate stoving primer and two coats of enamel paint on front sideandgreystoveenamelonbacksideandborder/messages/ symbols etc. with approved colour shade paint complete, on M.S.angleofsize35x35x3mmframewithproperlycrossbraced M.S.anglesofsize35mmx35mmx3mmdulypaintedincludingTwo M.S.angleironpostsofsize65mmx65mmx6mm,3.65mlong painted with alternate black and white bands of 25 cm width including all fixtures etc.and fixing the boards in 1:4:8 concrete block of size 60 cm x 60 cm x 75 cm including, excavation, refilling, transportation, and labour etc complete. Spec. No. As directed by Engineer in Charge (Item No. No. 6.36) 12 Add For Roylaty Sand 13 Add For Royalty Other 14 Add For Testing 15 Add For Insurance 16 AddFor GST

BRR:7526153 Supply With Transportation At Site Of Hydraulic Bale Press Machine For Pwm.

BRR:7525713 Supply Of Slrm Operational Tools And Safety Equipment For Solid Liquid Resource Management On Rate Contract , Tarpalin Accessories (Size: 12X9) , Aluminium Basket (Big 20) , Aluminium Basket (Medium 15) , Aluminium Basket (Small 10) , Sitting Stool - 8 Height , Plastic Bora Bags (Big) , Plasticbora Bags (Medium) , Plasticbora Bags (Small) , Pest-O-Flash (Flies Trapping Light) , Small Knife For Plastic Cover Cutting (Reusable) , Tailoring Scissor , Pipe (½ Inches) , Stitching Needle (Plastic Cover) , Plastic Rope ( Sutli – Stitching) , “T” Type Angle (Drying) , Tea Filter (Big Size) , Cotton Mask (Eco-Friendly, Washable & Reusable) , Cap (Eco-Friendly, Washable & Reusable) , Raincoat-Free Size , Reflactive Jacket For Male(Free Size) , Gumboot Free Size , Canvas Shoes , Cotton Socks , Cotton Gloves (Eco-Friendly, Washable & Reusable) , Rubber Gloves (Size: 14) , Rubber Gloves (Size: 18) , Water Bottle (Steel) -1 Ltr , Name Badge , Id Card , Spade With Wooden Handle(Heavy Duty) , Crowbar (24 Inches) – Steel , Aluminium Mug (Small) , Felling Knife (Steel) , Shovel - Sharp Edge , Shovel - Broad Edge , Broom Stick - With Handle , Broomstick - Brush Type , Broomstick , Rake(Telescopic Garden Rake) , Rake With Angle (Big Size) , Pick Axe , Hammer(Medium Size) , First Aid Box With Kit (Medium Size) , Sanatizer , Drainage Spoon With Handle(Big Size) , Chain With Lock , Key Chain , Tool Box , Brass Bell 1.75-2.00 Kgs , Coir Brush – Handy , Iron Brush – Handy , Water Barrel-120 Ltr , Spring Balance 100Kgs , Weighing Machine 200 Kgs , Jute Bora Bags (Big) , Jute Bora Bags (Medium) , Jute Bora Bags (Small) , Bale Box , Leg Pump-Pressure Check , Hand Pump – Pressure Check , Sieve - Gi (Size:5 X 4) , Hose Pipe 30 Mt , Aluminium Pots , Flower Bucket , Iron Plates (Size: 6 X 8) , Hand Wash (Dettol) , Pounder , Rava - Sieve – Small , Emergency Light-6 Watt , Torch , Plastic Rope (Sutli – Baling) , Printer , Cartridge , Paper(A4) Rim , Legal Size Paper , Note Pad , Pen , Record Register , Attendance Register , Stapler(Big Size) , Stapler(Small Size) , Stapler Pin (Big Size) , Paper Pin , Stapler Pin(Small Size) , Mrker Pen (Permanent) , Marker Pen (Temperory) , Fevistick Glue , Single Round Paper Punching , Cello Tape , File Tag , Flat Office File , Office Ring File , Water Filter , Towel , Plastic Chair , Office Chair , Computer Table , Almira , Extension Board , Kitchen Utensies Set (Steel) , Plastic Mug , Kettle , Phenyl Balls , Toilet Cleaner Liquid , Toilet Brush , Bamboo Basket , Trycycle (For Collection Of Garbage) , Bleaching Powder , Sarees

BRR:7525146 Development Block Ramnagar Gram Sabha-Talaspur CC road construction work from Harilal Patels Chak to Rajendra Patels house - Excavation infoundations in ordinary soil (Loamclay or Sand) including lift upto 1.5 metre and lead upto 30Mand including filling watering and ramiming of excavated earth into the space between the bulding and the side offoundation trenches or into the plinth and removal and disposal of surplus earthad directed by the Engineer-in-chargeupto a distance of 30m from the foundation trenches including all T&P Phowarah and basket etc.Complete.As per S.I.No.251 3 Earthwork in cutting or in embankment in ordinary soil,excavation to be in the form of regular pits not exceeding 0.5m in depth and earthwork in embankment to be in 8 layers, including ramming and dressing the surface to required levels aand slopes and also inc. 1.5 m and 30 m lead. the earth form cutting to be used in making and embankment or to be deposited as spoil banks within 30 m distance as directed by the E/I.etc . and Including Cartage Upto 2Km. Distance As per S.I.No.253 4 Concrete with 40mm gauge brick ballast,sand of 1.25 F.M. & cement in proportion of 12:6:1 in foundation and under floors includingsupply of all materials,labour and Tools and Plantsetc.requiredfor proper completion of the work. As per S.I.No.273. 5 M-150 Brick work in 1:4 cement and coarse sand of 1.25 fineness modulous mortar in foundation and plinth including supply of all material,labour and tools and plants, etc. required for proper completion of the work. SI-305 B 6 CONTRUCTION of granular sub base(grade-1)G.S.B. by provided well graded material, spreading in unifrom layers with graded on prepared surface, mixingby mix in place method with rotavator at OMC and compacting with smooth rollar to achived the desired densty completeas per T.S.C.401 7 Providing laying spreading and compacting stone aggregates(size 22.40-53mm) ofwater bound macadam specification including spreading in uniform thickness hand packing-rolling with G-3- wheeled steel/vibratory roller 8-10 tonnes in stages to proper grade and camber applying and broomingrequisite type of screening/binding materials to fill-up the interstices of course aggregtate watering and compacting to the required density grading 3 as per Technical Specification clause 405. 8 Construction of un-reinforced, plain cement concrete pavement thickness as per design over a prepared sub base with 43 Grade cement or any other type as per clause 1501.2.2. M 30 (Grade) coarse and fine aggregates conforming to IS :383, maximum size of coarse aggregates not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weight batcher using approved mixed design, laid in approved fixed side form work ( steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plate, including levelling the formwork as per Drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion,construction, joints, applying debonding strips, primer, sealent, admixtures as approved, curing of concrete slabs for 14 days, curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501 9 R.C.C. Hume Pipe NP-350mm Including collars/Spigot Jointed withStiff Mixture of cement in the Proprotion of 1:2 (1 cement : 2 find Sand Including Testing of Joints. SI-26 10 Supply and fixing of informatory M.S sign board, size 1.2X0.90m made of 18mm gauge M.S sheet fic in ISA 40X40X6mm, frame support in back side by 40X5mm flat iron on all four side along with to vertical post of2.90mt. Diagonal bracing of size 40x5mm fiat iron, electrically welded and painted with one coat red oxide primer and 2 coat superier quality enamel paint with lettering work of required specified information also I/c fixing in trench both side C.C. 1:2:4 size 0.45 x 0.45x0.50 m Required for proper complation of the work. Reference SpecificationS.I. No. 502

BRR:7524264 Tender For Supply, Installation, Testing And Commissioning Of Floor Type Weighing Machine Of 1000 Kg Capacity At Domestic Cargo Terminal At Sgrdji Airport, Amritsar.

BRR:7522658 Tender For Purchase Of Industrial Accessories , Industrial Grade Stove/Burner Ladder , Ss Tank For Oil Storage , Ss Tank For Asav/Arishth , Electronic Platform Type Weighing Scale 1000 Kg , Electronic Platform Type Weighing Scale 500 Kg , Electronic Platform Type Weighing Scale 50 Kg , Electronic Platform Type Weighing Scale 10 Kg , Ss Container (Bhagona) , Platform Stool Ladder , Pallet For Godown Storage , Spatula (Palta) , Dump Cart Trolley For Material Handling , Centrifuge S.S.304 36

BRR:7522486 Tender for painting, whitewashing and other miscellaneous works of boundary wall of non-residential building in the premises of District Magistrate Office in Sant Kabir Nagar district Lot 02, 1 Laying and Jointing PVC Pipe. Heading 2 Finishing wall with water proof cement paint of approved make and quality on new work with 3 coats to give an even shade completion of the work. S.I N0 660+661Complete in all respects as Per direction of Ergineer-In-Charge. 3 Fencing with R.C.C. post placed at required distance, embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post one side only. provided with horizontal lines and two diagonals of barbed wire weighing 9.38 kg per 100 metres (minimum), between the two posts fitted and fixed with G.I. staples on wooden plugs or G.I. binding wire tied to 6 mm bar nibs fixed while casting the post (cost of R.C.C. posts, struts, earth work and concrete to be paid for separately) Payment to be made per metre cost of total length of barbed wire used. As per DSR 16.17.1 with G.I. Complete in all respects as Per direction of Ergineer-In-Charge. 4 Paninting on previously painted old surface with paint of mediam Quality on wood or steel snd other metal surface with superior synthetic enamel standard make brushing to give an even shade and finish and including cleaning the surface of all dirt dust and other foreign matter sand papering and stripping including cost of all materials labour T&P etc required for the proper complition of the work.as per SI No new item 3 ii (painting)Complete in all respects as Per direction of Ergineer-In-Charge. 5 Providing and fixing 1 mm. thick M.S. sheet garrage door with frame of 40x40 x 6 mm (11⁄2 x 11⁄2 x 4) angle iron, 3.15 mm 1/8 thick M.S. gusset plates at the junctions and corners, including supply and fixing of necessary fittings. lock rail of 37.5cm length of oxidised iron and including pintels, hooks at the top and applying a priming coat of red lead paint on all sides complete. item no. 517a Complete in all respects as Per direction of Ergineer-In-Charge. 6 Painting of Tree up to 1.20 m Hight (as per Market Rate) Complete in all respects as Per direction of Ergineer-In-Charge.

BRR:7522354 Tender For Ramjanaki Kharagpur Road To Atraulia Pathan Tola Link Road - WBM G-3 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheeled 80-100 kn in stages to proper grade and camber, applying and brooming crushable screening to fill up the interstices of coarse aggregate, watering and compacting to the required density grading-3 as per T.S.C. 405 including labour cess. (GST shall be paid extra) 2 Tack Coat-Providing and applying tack coat with bitumen (VG-10)using bitumen pressure distributor at the rate of 0.30kg per sqm on the prepared bituminous surfacecleaned with Hydraulic broom as per Technical Speicification Clause 503. including labour cess.(GST shall be paid extra) 3 Premix Carpet-Providing, laying and rolling of open-graded premix carpet of 20mm thickness composed of 13.2 & 11.2 mm aggregates either using penetration grade bitumen or emulsion to required line grade and level to serve as wearing coarse on a previously Prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100kN static roller capacity finished to required lavel and grades to be followed by seal coat as per Techincal Specification clause 508 including cost of bitumen & labour cess. (GST shall be paid extra) 4 Seal Coat-Providing and applying seal coat type C comprising of a layer of bituminous binder followed by a cover of stone chipping of specified grading and rolling with power roller 8-10 tonne kN Static roller and finishing to required level and grades as per Technical Specification Clause 510 including cost of bitumen & labour cess.(GST shall be paid extra). 5 Cement Concrete Pavement Construction of un-reinforced, dwel jointed, plain cement concrete pavement over a prepared sub base with approve grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous peration including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per design. including labour cess. 6 Earth Work in Patari as per Si.No. 253.

BRR:7522349 Bids Are Invited For Lab Stools Revolving Stainless Steel , Burette clamp with iron stand iron , Burette B grade , Chemical balance with weight box , Digital Calorie meter , Funnel Pack of 2 50MM 65MM 75MM , Test tubes Borosilicate glass with Stand 15ML Pack of 12 , Test tubes 3 ML Pack of 48 , Boiling Tube Pack of 12 , Pipettes 10ML Pack of 4 , Conical flask Pack of 8 , Volumetric flask Pack of 5 , Graduated centrifuge tube Pack of 25 , Dropper Pack of 25 , Reagent bottle , KIPPs apparatus Set , Conductivity Meter , Colorimeter , Deep freezer 150 , Hot air oven , Electronic top pan balance 1 Mg to 220 Grm , Filter flask 1000 ml Borosil , Melting point apparatus Manual , Aspirator Bottles 250ML 500ML Set of 2 , Nesslers Cylinders Pack of 10 , Desiccators Set of 3 , Petri Dishes Set of 3 , Distilling Apparatus , Filtration Assembly All Glass Filter Holder , Gas Generator 500ML and 1000 ML , Forceps and Pointed Dissecting Set of 5 , Triangular Tripod , Optical Microscope with Transmitted Stand , Centrifuge , pH Meter , Spirit lamp , Micrometer Screw Gauge , Stop Watch Digital Racer , Plug Key Two and Four way Set of 6 , Sprit level 250MM 400MM , Multimeter , Rheostant Set of 2 , Spherometer , Reading lenses Magnifying , Stop Clock Mechanical , Galvanometer thirty zero thirty , Ammeter 0 to 3amp and 0 to10 amp , Battery Eliminator , Flywheel Complete set with vernier callipers digital stop watch set of weight and a pen , Zener Diode Characteristic , Characteristic of Transistor , Tunnel Diode characteristic apparatus , Carry foster bridge complete set , Analog Anderson Bridge , DC Power Pigtail Male Cable Wire , Hartley Oscillator complete set , Digital Oscilloscope , Operational Amplifier Discrete Component Trainer , Digital Storage Oscilloscope , Quinckes Tube , Torsional Pendulum Hall Effect Experiment , Stadiometer , Refrigerator , R O Water purifier , Harpenden Calliper , Polygon Law of Forces Apparatus , Verification Of Lamis Theorem , Simply Supported Beam Apparatus , Inclined Plane SetUp , Bell Crank Lever Apparatus , Moment Of Inertia Of Flywheel SetUp , Screw Jack SetUp combined , Wheel and Axial SetUp , Worm and Worm Wheel SetUp , Reynolds Apparatus , Bernoullis Theorem Apparatus , Mouthpiece Orifice , Impact of Jet On Vanes , Triangular Rectangular Notch , Venturi Meter and Orifice Meter , Friction Factor Apparatus Miner Losses , Centrifugal Pump Constant Speed , Tachometer , Kaplan Turbine , Hydraulic Jump , Hydraulic Tilting Flume , Turbine Flow Meter , Micro Manometer , Binacular Polarizing Microscope , Hydraulic Mounting press 3T , Specimen leveler , Damped Spring Mass Vibrating System , Static Balancing Using Steel Balls , Motorized Gyroscope , Whirling of Shaft Apparatus , CAM Analysis Apparatus , Universal Governor Apparatus , Universal VIB Vibration Lab , Epi Cyclic Gear Train Holding Torque Apparatus , Turn Table Apparatus , 4 Bar Mechanism Slider Crank Oscillating Cylinder Whitworh 4Bar link Mechanism , Gear Trains Single Stage Spur gear with intermediate Gear Differential Gear , Stefen Boltzman Constant Apparatus , Heat and Mass Transfer Apparatus , Thermal Conductivity Of Insulating Powder Apparatus , Heat Transfer Through Heat Exchanger Apparatus , Four Probe Conductivity Energy gap of semiconductor , Dielectric Constant dielectric constant of insulating materials , Capacitance Box , He Ne Laser determination of wavelength of laser , Spectrometer dispersive power Determination of wavelength of source , Bomb Calorimeter calorific value of solid liquid lab , Digital Conductivity Meter Determination of conductance and strength of the acids and base , Photo Electric Calorimeter Determination of Absorbance and verification of beers law , Refractometer Refractoriness of the solids and liquid samples , Digital Bulk Density apparatus to Determination of density of solid substances , Redwood Viscometer No II To determine the viscosity of Thin samples , Water Analyzers includes calorimeter DO Conductivity TDS pH Salinity and Temperature , BOD Incubator determine the amount of biological oxygen required in water samples , COD Apparatus determine the Chemical oxygen requirement in water samples , Torsion Testing Machine , Tensile Testing Machine Springs , Vernier Calipers 200 mm and 300 MM , Universal Testing Machine 60 Tones , Dial Gauge Plunger and Lever Type with Magnetic Stand , Malus Law Apparatus , Electric Vibrator , Gray Prism Spectrometer , Newtons Ring with Spherometer a Total Quantity : 423

BRR:7522027 Bids Are Invited For Spares For Self Loader Concrete Mixer 4 Cum Ajax 444466 Filter For Water Pump Section , A3891 Return Suction Filter , 1000008003 Eco Matrix Cluster 00804 , A9389111001 Filter Element , 200100003703 Radial Ball Bearing 444466 Filter For Water Pump Section, A389111 Return , Oem Spares For Automobiles Total Quantity : 11

BRR:7521645 Tender For Supply of Material Supply Mini Mcf - mild steel tubes hot finished welded type Red oxide Zinc chromate primer welding by electric plant Galvanised wire mesh of average width of apeture 1.4 and nominal diaof wire 0.63 mm wire nails Gi Traffold profile sheet 0.35 mm thick Bitumin washer Stainless steel screws50 mm Collection ofStone aggregate 20 mm nominal sizeincluding all cost conveyance labour charges etc complete. Collection ofStone aggregate 10 mm nominal sizeincluding all cost conveyance labour charges etc complete. Collection ofcoarse sand zone III (M-sand) all cost conveyance labour charges etc complete. Collection of Cement including all cost conveyance labour charges etc complete. Higher charges of concrete mixer .25 to 0.40 cum hopper Vibrator (needle type 40 mm)

BRR:7521625 Tender For Mgnrega Material Work Ward 1-3 Material Supply For Mgnrega Work Ward 1-3 , Material Work Ward 1-3 , Stone For Masonry Work , Quarry Waste , Stone Aggregate(Single Size): 40 Mm Nominal Size , Stone Aggregate(Single Size):20 Mm Nominal Size , Stone Aggregate(Single Size): 10 Mm Nominal Size , Coarse Sand (Zone Iii) , Portland Cement , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With Hopper , Vibrator (Needle Type 40 Mm) , Sundries , Wall Form Panel 1250X500 Mm , Corner Angle 45X45x5 Mm 1.50 M Long , 100 Mm Channel Shoulder 2.5 M Long , Double Clip (Bridge Clip) , Single Clip , M.S. Tube 40 Mm Dia , Wall Form Panel 1250X450xmm , Column Clamp 450X1070 Mm , Prop 2 M (2-3.5M) , Laterate Stone Of Size 40X20x15cm , Royalty For Good Earth , Twisted Steel/Deformed Bars , Fine Sand (Zone Iv) , Solid Blocks Of Size 40X20x15cm , Mild Steel Tubes Hot Finished Welded Type , Red Oxide Zinc Chromate Primer , Welding By Electric Plant , Gi Trafford Profile Sheet 0.35Mm Thick , Bitumen Washer , Stainless Steel Screws 50 Mm , Rolling Shutter Made Of 80X1.25 Mm Machine Rolled Laths , Top Cover For Rolling Shutters 1.25 Mm Thick , 27.5 Cm Long Wire Spring Grade No 2 For Rolling Shutters , Galvanised Wire Mesh Of Average Width Of Aperture 1.4 And Nominal Dia. Of Wire 0.63 Mm , Wire Nails , Deharadun White Lime , Plastic Emulsion Paint , Vitrified Floor Tile 60X60 Cm , Black Plastic Seat (Soild) With Lid C.P.Brass Hinges And Rubber Buffers , Vitreous China Pedestal Type Wate Closet , Flushing Cistern P.V.C. 10 Lts Capacity (Low Level) (White) (With Fittings, Accessories And Flush Pipe) , Pvc Pipe 25 Mm Outer Dia. 10Kgf Cm2 , Factory Made Door Frame Size 50X47 Mm With Wall Thickness 5 Mm Made Of Single Piece Extruded Profile

BRR:7521624 Tender For Mgnrega Material Work Ward 4-6 Material Supply For Mgnrega Work Ward 4-6 , Material Work Ward 4-6 , Stone For Masonry Work , Quarry Waste , Stone Aggregate(Single Size): 40 Mm Nominal Size , Stone Aggregate(Single Size):20 Mm Nominal Size , Stone Aggregate(Single Size): 10 Mm Nominal Size , Coarse Sand (Zone Iii) , Portland Cement , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With Hopper , Vibrator (Needle Type 40 Mm) , Sundries , Wall Form Panel 1250X500 Mm , Corner Angle 45X45x5 Mm 1.50 M Long , 100 Mm Channel Shoulder 2.5 M Long , Double Clip (Bridge Clip) , Single Clip , M.S. Tube 40 Mm Dia , Royalty For Good Earth

BRR:7521621 Tender For Mgnrega Material Work Ward 7-9 Material Supply For Mgnrega Work Ward 7-9 , Material Work Ward 7-9 , Stone For Masonry Work , Quarry Waste , Stone Aggregate(Single Size): 40 Mm Nominal Size , Stone Aggregate(Single Size):20 Mm Nominal Size , Stone Aggregate(Single Size): 10 Mm Nominal Size , Coarse Sand (Zone Iii) , Portland Cement , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With Hopper , Vibrator (Needle Type 40 Mm) , Sundries , Wall Form Panel 1250X500 Mm , Corner Angle 45X45x5 Mm 1.50 M Long , 100 Mm Channel Shoulder 2.5 M Long , Double Clip (Bridge Clip) , Single Clip , M.S. Tube 40 Mm Dia , Twisted Steel/Deformed Bars

BRR:7521619 Mgnrega Material Work Ward 10-12 Material Supply For Mgnrega Work Ward 10-12 , Material Work Ward 10-12 , Stone For Masonry Work , Quarry Waste , Stone Aggregate(Single Size): 40 Mm Nominal Size , Stone Aggregate(Single Size):20 Mm Nominal Size , Stone Aggregate(Single Size): 10 Mm Nominal Size , Coarse Sand (Zone Iii) , Portland Cement , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With Hopper , Vibrator (Needle Type 40 Mm) , Sundries , Wall Form Panel 1250X500 Mm , Corner Angle 45X45x5 Mm 1.50 M Long , 100 Mm Channel Shoulder 2.5 M Long , Double Clip (Bridge Clip) , Single Clip , M.S. Tube 40 Mm Dia , Twisted Steel/Deformed Bars , Safeda Ballies 125 Mm Diameter , Second Class Kail Wood In Scantling , Second Class Kail Wood In Planks , Structural Steel Such As Tees, Angles, Channels And R.S. Joists , Adjustable Span Eso+Si (2.35-3.40) , Adjustable Telescopic Prop 3 M (2.02-3.75M) , Twisted Steel/Deformed Bars , Pvc Pipe 63 Mm Outer Dia . 6Kgf/Cm2 , Pvc Bend 63 Mm Dia , Pvc Door Tee 63 X63x63mm Dia , Pvc Vent Cowl 63 Mm Dia , Column Clamp 450X1070 Mm , Prop 2 M (2-3.5M)

BRR:7521616 Mgnrega Material Work Ward 13-15 Material Supply For Mgnrega Work Ward 13-15 , Material Work Ward 13-15 , Stone For Masonry Work , Quarry Waste , Stone Aggregate(Single Size): 40 Mm Nominal Size , Stone Aggregate(Single Size):20 Mm Nominal Size , Stone Aggregate(Single Size): 10 Mm Nominal Size , Coarse Sand (Zone Iii) , Portland Cement , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With Hopper , Vibrator (Needle Type 40 Mm) , Sundries , Wall Form Panel 1250X500 Mm , Corner Angle 45X45x5 Mm 1.50 M Long , 100 Mm Channel Shoulder 2.5 M Long , Double Clip (Bridge Clip) , Single Clip , M.S. Tube 40 Mm Dia , Wall Form Panel 1250X450xmm , Corner Angle 45X45x5 Mm 2.50 M Long , Column Clamp 450X1070 Mm , Prop 2 M (2-3.5M)

BRR:7521611 Supply of Materials for Flood protection works underMGNREGAscheme-Balussery Grama Panchayath-Collection of STONEincluding all cost conveyance labour charges etc complete. 2 Supplying and stacking in standard profile and heap for measurement at site Quarry waste ,including all cost and conveyance and all labour charges including stacking etc complete 3 Supplying and stacking in standard profile and heap for measurement at site Stone aggragate 40 mm nominal size ,including all cost and conveyance and all labour charges including stacking etc complete 4 Supplying and stacking in standard profile and heap for measurement at site Stone aggragate 20 mm nominal size ,including all cost and conveyance and all labour charges including stacking etc complete 5 Supplying and stacking in standard profile and heap for measurement at site Stone aggragate 10 mm nominal size ,including all cost and conveyance and all labour charges including stacking etc complete 6 Supplying and stacking for measurement at site Portland Cement (ISI standard) , including all cost and conveyance and all labour charges including stacking etc complete 7 Supplying and stacking in standard profile and heap for measurement at site Coarse Sand - zone III (M sand for concrete work) ,including all cost and conveyance and all labour charges including stacking etc complete 8 Collection of twisted steel/deformed barscost conveyance labour charges etc complete. 9 Collection of M.S Tube 40mm diacost conveyance labour charges etc complete. 10 Collection of single clipcost conveyance labour charges etc complete. 11 Collection of double clip(bridge clip)cost conveyance labour charges etc complete. 12 Collection of 100mm channel shoulder 2.5m longcost conveyance labour charges etc complete. 13 Collection of corner angle 45x45x45mm 1.5m longcost conveyance labour charges etc complete. 14 Collection of wall form panel 1250x500mmcost conveyance labour charges etc complete. 15 Collection of Finesand (zone Iv)cost conveyance labour charges etc complete. 16 Higher charges of concrete mixer 0.25 to 0.40cum hopper 17 Higher charges of Vibrator (needle type 40 mm )

BRR:7521607 Supply of Materials forSHG work shed underMGNREGAscheme-Balussery Grama Panchayath-Collection of STONEincluding all cost conveyance labour charges etc complete. 2 Supplying and stacking in standard profile and heap for measurement at site Stone aggragate 20 mm nominal size ,including all cost and conveyance and all labour charges including stacking etc complete 3 Supplying and stacking in standard profile and heap for measurement at site Stone aggragate 10 mm nominal size ,including all cost and conveyance and all labour charges including stacking etc complete 4 Supplying and stacking in standard profile and heap for measurement at site Coarse Sand - zone III (M sand for concrete work) ,including all cost and conveyance and all labour charges including stacking etc complete 5 Supplying and stacking for measurement at site Portland Cement (ISI standard) , including all cost and conveyance and all labour charges including stacking etc complete 6 Solid blocks of size 30x20x15cm 7 Structural steel such as tees, angles, channels and R.S. joists 8 Red oxide Zinc chromate primer 9 Adjustable telescopic prop 3 m (2.02-3.75m) 10 Beam clamp 300-380 mm (450-1070 mm) 11 Collection of twisted steel/deformed barscost conveyance labour charges etc complete. 12 Stone Aggregate(single size): 40 mm nominal size 13 Fine sand (zone IV) 14 Water thinnable cement primer for interior wall surface, having VOC content less than 50 gms/litre 15 Plastic emulsion paint 16 Ceramic Glazed Tiles Ist quality minimum thickness 5 mm in all colours shades and designs except burgundy, bottle green black 17 Epoxy paint 18 Ceramic Glazed Tiles Ist quality 300 x 300 mm in all shades and designs of White, Ivory, grey, Fume Red brown etc. 19 Mild steel sheets for tanks 20 Iron pintels including weldded pin 21 Mild steel sheets with bolts and nuts to rest on pintels 22 Mild steel hooks 23 Hollock wood in planks 24 Kiln seasoning of timber 25 Float glass sheet of nominal thickness 4 mm (weight not less than 10 kg/sqm) 26 Bright finished or black enameled mild steel butt hinges 100x58x1.90 mm 27 Bright finished or black enameled mild steel butt hinges 50x37x1.50 mm 28 Bright finished or black enameled mild steel screws 40 mm 29 Bright finished or black enameled mild steel screws 20 mm 30 Mild steel tubes hot finished welded type 31 Welding by electric plant 32 Galvanised steel J or L hooks 8 mm dia 33 Bitumen washer 34 G.I. Plain washer thick 35 Precoated Aluminium Trafford sheet 0.450mm thick 36 Black plastic seat (soild) with lid C.P.brass hinges and rubber buffers 37 Vitreous china pedestal type wate closet 38 Flushing Cistern P.V.C. 10 lts capacity (low level) (white) (with fittings, accessories and flush pipe) 39 Hire charges of Concrete Mixer 0.25 to 0.40 cum with Hopper 40 Higher charges of Vibrator (needle type 40 mm )

BRR:7521600 Supply of Materials for Road works underMGNREGAscheme-Balussery Grama Panchayath-Collection of Red earth ncluding all costconveyance labour charges including stacking etc complete. 2 Supplying and stacking in standard profile and heap for measurement at site Quarry waste ,including all cost and conveyance and all labour charges including stacking etc complete 3 Supplying and stacking in standard profile and heap for measurement at site Stone aggragate 40 mm nominal size ,including all cost and conveyance and all labour charges including stacking etc complete 4 Supplying and stacking in standard profile and heap for measurement at site Stone aggragate 20 mm nominal size ,including all cost and conveyance and all labour charges including stacking etc complete 5 Supplying and stacking in standard profile and heap for measurement at site Stone aggragate 10 mm nominal size ,including all cost and conveyance and all labour charges including stacking etc complete 6 Supplying and stacking for measurement at site Portland Cement (ISI standard) , including all cost and conveyance and all labour charges including stacking etc complete 7 Supplying and stacking in standard profile and heap for measurement at site Coarse Sand - zone III (M sand for concrete work) ,including all cost and conveyance and all labour charges including stacking etc complete 8 Higher charges of concrete mixer 0.25 to 0.40cum hopper 9 Higher charges of Vibrator (needle type 40 mm )

BRR:7521598 Material Supply For Individual Work Material Supply For Individual Work For Mgnrega , Soak Pit,Cib & Nursery , Second Class Kail Wood In Planks , Second Class Kail Wood In Scantling , Safeda Ballies 125 Mm Diameter , Stone Aggregate(Single Size):20 Mm Nominal Size , Stone Aggregate(Single Size): 10 Mm Nominal Size , Coarse Sand (Zone Iii) , Portland Cement , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With , Vibrator (Needle Type 40 Mm) , Sundries , Twisted Steel/Deformed Bars , Pvc Pipe 63 Mm Outer Dia . 6Kgf/Cm2 , Pvc Bend 63 Mm Dia , Pvc Door Tee 63 X63x63mm Dia , Pvc Vent Cowl 63 Mm Dia , Citizen Information Board 3 X 4 , Citizen Information Board 2 X 3 , Citizen Information Board 2 X 3 Wall Writing , Royalty For Good Earth , Cowdung , Green Net 75% Shade , Aracanut Post , Polyurethene Bags , Chicko Seeds , Guava (Pera ) Seeds , Pomegranate(Mathalam) Seeds , Jack Fruit Seeds , Rambuttan Seeds

BRR:7520324 Supply, installation and commissioning Vartical Milk Storage Tank (Silo) Capacity 30000 ltr. At Rahta Taluka Sahakari Dudh Utpadak Sangh RahtaDist- A.Nagar. -

BRR:7520315 Supply Of Various Type Material At Village Pangri Ugale Tq Sindkhed Raja Dist Buldhana , Name Of Items : , All In One Lager Printer , 25Lph Ro , 18 W Light , Solar Light , 24 W Light , 36 W Led Light , 1 Meter Wire 1Mm , Holder (1 Nos) , Clamp And Pipe Set , Tcl Power 25 Kg Bag , Weighing Scale 100Kg And Above , Hight Chart , Infrentometer , Stadiometer With Weighing Scale , Weighing Scale For Baby , Aakar Khelni Sanch 0 Te 5Yr With Chart , Anganwadi Karita Kothi 100 Kg , Anganwadi Karita Kothi 50 Kg , Kapat 4X3 Size , Kapat 7X3 Size , Kukar 10Kg , Kukar 25Kg , Palte Pavbhaji , Water Glass Ss , Table 2X4 Size , Khurchi Nilkamal Plastice , Hand Wash Station 1 Besin , Hand Wash Station 4 Besin , Led Smart Tv 32 , Led Smart Tv 40 , Led Smart Tv 50 , Cricket Set (2 Bat , 6 Ball, 2 Pair Stamp, Hand Glos 3 Pair, Pad 3 Pair , Helmet 3 Pair) , Sound System Withmick And Trolly (10) , Foot Ball , Pen Drive 64 , Medical Kit (Oximter, Turmameter, Bandez, Iodine,Cipladim) , B P Aprates (Isi Mark) , Saniterypad (6 Nos Set) , Suger Test Kit (Isi Mark) , Bebi Powder (Jonsun Baby) , Bebi Powder (Himalay) , Machardani For 0 Te 1 Yr Baby , Tharmameter , Preganews Kit , Kadahi 10Kg , Bhagune 10Kg , Baket 10Ltr , Topale 5 Kg , Bhat Wadi , Vaghral , Kavcha , Mat 12X20 Size , Mat 6X10 Size , Computer Set (500Gb Hhd,4Gb Ram, I3 Processer With Keybord Mouse, Vga And Power Supply) 1 Year Warranty , Moniter 22 , Moniter 15 , Laptop (1Tb Hhd,4Gb Ram, I3 Processer) 1 Year Warranty , Small Tractor For Rent Per Day With Fawarni Yantra With Driver , Deltafog 1 Ltr , Deskbench Small Size 1 To 5 Year Childern , Babay Chire 40X32x30x20 Size , Slide 58X18x36x54 Size , Super Swing 30X33x43 , Book For Laburary (1 Set Samaj Sudharak Yanche 5 Book, Bharat History 1Book, Othe R4 Book ) 10 Book Set , Water Jar 18 Ltr , Handicap Wheel Chire (For Handicap) , Balnket , Handicap Walker , Ciling Fan , Childer Dress 1 Yr , Childer Dress 2 Yr , Childer Dress 3 Yr , Childer Dress 4 Yr , Childer Dress 5 Yr , Wheel Chare

BRR:7519978 E-Tender For Repairing Of Low Cost Bio Medical Equipment At Rg Kar Mch- 1 Refrigerator 2 Change of cooling coil 3 Repair of compressor 4 Change of compressor 5 Change relay/overload/timer 6 Gas charge 7 Repair of leg 8 Repair of body 9 Dressing Drum 10 Change of hinge 11 Repair of belt 12 Change of lock 13 Repair of Body 14 Change of jacket 15 Change of handle 16 Sterilizer machine 17 Change of thermostat 18 Change of plug top 19 Change of element 1 KW 20 Change of element 1.5 KW 21 Change of element 2 KW 22 Change of kettle element 1/ 1.5 kw 23 Change of U element ( 1 / 1.5 kw) 24 Change of Cable (3 Core) 25 Repair of body 26 B P Apparatus digital 27 Change of Cuff 28 Repair of PCB 29 Repair of air pump 30 B P Apparatus Aneroid 31 Change of ball 32 Change of cuff 33 Change of valve 34 Change of bellow 35 Repair of dial 36 B P Apparatus mercury 37 Change of ball 38 Change of cuff 39 Change of valve 40 Change of bellow 41 Change of glass 42 Mercury 43 X Ray View box 44 Change of Tube 45 Change of plug Top 46 Change of power Cable 47 Change of choke 48 Change of starter 49 Change of vinyl 50 Lamp Infra red 51 Change the lamp itself 52 Change of holder 53 Change of cable 54 Change of plug top 55 Lamp UV 56 Change the lamp itself 57 Change of holder 58 Change of cable 59 Change of plug top 60 Flicker Fusion Apparatus 61 Change of probe 62 Change of power supply board 63 Change of transformer 64 Change of meter 65 Nebulizer 66 Change of motor 67 Change of piston 68 Change of power cord 69 Change of plug top 70 Change of fuse 71 Syringe electrical 72 Syringe itself petty repair 73 Needle Destroyer 74 Change of transformer 75 Change of power cord 76 Change of plug Top 77 Change of main switch 78 Change of cutting plate 79 Illuminator 80 Complete repair 81 Vision chart 82 Change of light 83 Change of fiber body 84 Change of cable 85 Change of plug top 86 Stirrer magnetic 87 Change of board 88 Change of power supply board 89 Change of regulating knob 90 Change of power cord 91 Automatic razor sharpener 92 Complete repair 93 Hand and foot puva 94 Complete repair 95 Laryngoscope 96 Change of bulb 97 Pipette 98 Change of pipette tip 99 Calibration required 100 Slide warmer 101 Change of heater 102 Change of light 103 Weighing scale 104 Complete repair 105 Flame photometer 106 Change of jar 107 Change of lense 108 Change of burner 109 Hot plate 110 Change of board 111 Change of main switch 112 Change of heating element 113 Change of regulator 114 Foetal Doppler 115 Change of digital board 116 Change of power supply board 117 Change of battery 118 Change of charger 119 View Box LED 120 Change of power supply 121 Change of Led strip 122 Change of power cable 123 Change of switch 124 Copper Drum 125 Change of heating element 3 KW 126 Change of Tap 127 Change of Power Cable 128 Change of plug Top 16 A. 129 Extension Board 130 Change of plug base 131 Change of switch 132 Change of Board 133 Change of Power cable 134 Washing Machine 135 Change of motor 136 Change of In let / Out let pipe 137 Repair of digital board 138 Repair of power supply pcb 139 Repair of solenoid valve 140 Weighing scale Digital 141 Change of power cable 142 Change of digital board 143 Change of power supply board 144 Dryer Machine 145 Change of motor 146 Change of In let / Out let pipe 147 Repair of digital board 148 Repair of power supply pcb 149 Repair of solenoid valve 150 Electric Kettle 151 Change of heating element 152 Change of switch 153 Change of power cable 154 Change of male socket 155 Change of female socket 156 Weighing scale 157 Change of spring 158 Change of display 159 Change of Balance 160 Air mattress Pump 161 Change of power cable 162 Change of air pump

BRR:7519693 Imp dev of road by pdg RMC P-4-Imp dev of road by pdg. RMC H. No. P-4/145 to H. No. P-4/168 and P-4/169 to P-4/192 Ward No. 50 Mangolpuri M-1/RZ., DSR DAR CIVIL-2018 and approved items; 2 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) 3 15.7.4:Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar 4 19.19.3.1:Providing and fixing in position Pre-cast R.C.C. manhole cover and frame of required shape and approved quality.H D - 20Circular shape 560 mm internal diameter 5 19.26.4:Raising manhole cover and frame slab to required level including dismantling existing slab and making good the damage as required (Raising depth of manhole to be paid separately :Circular manhole 140 cm dia with circular cover 600 mm dia of grade EHD - 35 6 16.64:Providing and laying 75 mm thick compacted bed of dry brick aggregate of 40 mm thick nominal size including spreading, well ramming, consolidating and grouting with jamuna sand, including finishing smooth etc.complete as per direction of Engineer-in- Charge. 7 16.75:Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately). 8 110.10:Providing and fiving name board made of MS Sheet 90x60cm, 1mm thick with frame of MS angle 50x50x6mm, two diagonal braces at the back of the sheet of MS flat 40x6mm, total height of the board above ground level 2.40m, length of legs below ground 0.30m embedded in CC block 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) 30x30x45cm including excavation and removal of surplus earth with in 50m lead, applying priming coat of approved steel primer, painting with synthetic enamel paint of approved quality and lettering with enamel paint of approved colour (one side) as per drawing/direction of Engineer-in-Charge 9 110.12:P/F precast R.C.C. stab/grating 70mm thick manufactured with CC 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 20 mm nominal size) reinforced with 96 kg/m3 of R.C.C including lapping all four side with M.S. sheet 1.6 mm thick & fixing in position complete. (Drain covers with or without holes) 10 1.1.1_08:Disposal of materials by mechanical transportincluding loading ,unloading and stacking lime ,moorum, buildingrubbish for lead 8 km

BRR:7519692 Tender For Civil Work - Const Of Road By Pdg Rmc-Const. Of Road By Pdg. Rmc Djb Office To Park Corner In Mangolpuri Ward 50 M-1/Rz., Dsr Dar Civil-2018 And Approved Items; 2 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) 3 15.7.4:Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar 4 19.19.3.1:Providing and fixing in position Pre-cast R.C.C. manhole cover and frame of required shape and approved quality.H D - 20Circular shape 560 mm internal diameter 5 19.26.4:Raising manhole cover and frame slab to required level including dismantling existing slab and making good the damage as required (Raising depth of manhole to be paid separately :Circular manhole 140 cm dia with circular cover 600 mm dia of grade EHD - 35 6 16.64:Providing and laying 75 mm thick compacted bed of dry brick aggregate of 40 mm thick nominal size including spreading, well ramming, consolidating and grouting with jamuna sand, including finishing smooth etc.complete as per direction of Engineer-in- Charge. 7 16.75:Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately). 8 110.10:Providing and fiving name board made of MS Sheet 90x60cm, 1mm thick with frame of MS angle 50x50x6mm, two diagonal braces at the back of the sheet of MS flat 40x6mm, total height of the board above ground level 2.40m, length of legs below ground 0.30m embedded in CC block 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) 30x30x45cm including excavation and removal of surplus earth with in 50m lead, applying priming coat of approved steel primer, painting with synthetic enamel paint of approved quality and lettering with enamel paint of approved colour (one side) as per drawing/direction of Engineer-in-Charge 9 110.12:P/F precast R.C.C. stab/grating 70mm thick manufactured with CC 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 20 mm nominal size) reinforced with 96 kg/m3 of R.C.C including lapping all four side with M.S. sheet 1.6 mm thick & fixing in position complete. (Drain covers with or without holes) 10 1.1.1_08:Disposal of materials by mechanical transportincluding loading ,unloading and stacking lime ,moorum, buildingrubbish for lead 8 km 11 16.45:Providing and fixing in position pre- moulded joint filler in expansion joints. 12 16.46.1:Providing and laying in position bitumen hot sealing compound for expansion joints etc. Using grade A sealing compound.

BRR:7519651 Supply Of Material For The Work Of Construction Of Post Harvesting Facilility Structure And Pucca Storage Facilities At Soriankuppam Village Panchayat In Bahour Commune Of Ariyankuppam Block, Puducherry. , [ Psr Code No.0983 - Pdy ] Supply Of Fine Sand (Zone Iv) , [ Psr Code No.0810 A - Pdy ]Supply Of Gravel , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With Hopper , Hire Charges Ofvibrator (Needle Type 40 Mm) , Supply Of Portland Cement , [ Psr Code No.0295 - Pdy ] Supply Of Stone Aggregate (Single Size) : 20Mm Nominal Size , [ Psr Code No.0982 - Pdy ] Supply Of Coarse Sand (Zone Iii) , [ Psr Code No.0293 - Pdy ] Stone Aggregate:40Mm Nominal Size , [ Psr Code No.0297 - Pdy ] Supply Ofstone Aggregate (Single Size) : 10 Mm Nominal Size , Supply Of Common Burnt Clay F.P.S. (Non Modular) Bricks Class Designation 3.5 , Hire Charges Ofwall Form Panel 1250X500 Mm , Hire Charges Of100 Mm Channel Shoulder 2.5 M Long , Hire Charges Ofdouble Clip (Bridge Clip) , Hire Charges Ofsingle Clip , Hire Charges Of M.S. Tube 40 Mm Dia , Supply Of Twisted Steel/Deformed Bars , [9999A] Supply Ofm30 Grade Cover Block , Supply Ofbitumen Hot Sealing Compound : Grade A , Supply Ofbitumen Solution Primer Of Approved Quality , Supply Of Flame Retardant Face Inslulating, Impregnated Fibre Board 12 Mm Thick , Supply Of Deharadun White Lime , Hire Charges Of A Welding By Electric Plant , Supply Of Mild Steel Tubes Hot Finished Welded Type , Supply Of Red Oxide Zinc Chromate Primer , Supply Of Precoated Glavanished Iron Profile Sheet 0.50 Mm Tct , Supply Of G.I. Plain Washer Thick , Supply Of Bitumen Washer , Supply Of Galvanised Steel J Or L Hooks 8 Mm Dia , Supply Of Mild Steel Sheets For Tanks , Structural Steel Such As Tees, Angles, Channels And R.S. Joists , Supply Of Iron Pintels Including Weldded Pin , Supply Of Mild Steel Sheets With Bolts And Nuts To Rest On Pintels , Supply Of Mild Steel Hooks , Supply Of Synthetic Enamel Paint In Black Or Chocolate Shade , Hire And Running Charges Of Hydraulic Piling With Power Unit Etc. Including Complete Accessories And Shifting At Site , Hire And Running Charges Of Light Crane , Production Cost Of Concrete By Batch Mix Plant , Pumping Charges Of Concrete Including Hire Charges Of Pump, Piping Work & Accessories Etc. , Hire Charges Of C.I. Pile Shoe , Hire Charges Of M.S. Clamps For Pile Shoe , Supply Of Plasticizer / Super Plasticizer , Providing One Number Of Citizen Information Board Of Size 0.90 X 1.20M For Community Work As Per The Standard Drawing Of Mord. Mgnrega(R.C.C. Precast)

BRR:7519650 Supply Of Material For The Work Of Construction Of Retaining Wall Back Side Of Pudukuppam Tsunami Nagar At Krishnavaram Village Panchayat In Bahour Commune Of Ariyankuppam Block, Puducherry. , [ Psr Code No.0983 - Pdy ] Supply Of Fine Sand (Zone Iv) , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With Hopper , Hire Charges Ofvibrator (Needle Type 40 Mm) , Supply Of Portland Cement , [ Psr Code No.0295 - Pdy ] Supply Of Stone Aggregate (Single Size) : 20Mm Nominal Size , [ Psr Code No.0982 - Pdy ] Supply Of Coarse Sand (Zone Iii) , [ Psr Code No.0293 - Pdy ] Stone Aggregate:40Mm Nominal Size , [ Psr Code No.0297 - Pdy ] Supply Ofstone Aggregate (Single Size) : 10 Mm Nominal Size , Hire Charges Ofwall Form Panel 1250X500 Mm For Centering , Hire Charges Of100 Mm Channel Shoulder 2.5 M Long For Centering , Hire Charges Ofdouble Clip (Bridge Clip) For Centering , Hire Charges Ofsingle Clip For Centering , Hire Charges Of M.S. Tube 40 Mm Dia For Centering , Providing One Number Of Citizen Information Board Of Size 0.90 X 1.20M For Community Work As Per The Standard Drawing Of Mord. Mgnrega(R.C.C. Precast)

BRR:7519583 Tender For Purchase Of Goods And Services Mnrega And Rd Schemes For Year 2025-26 Gram Panchayat Uparla , Purchase Of Goods And Services Mnrega And Rd Schemes For Year 2025-26 Gram Panchayat Uparla - 1 PARTICULARS 2 Ghadla / Kankar / Jhajhra 3 Mortar - Soil / Mud Masala 4 Lime - Lime from brick kiln for masonry work 5 Cement 6 PPC 7 White Cement 8 FINE AGREEGATE 9 Sand / Gravel 10 Gravel - Local / LOCAL 11 Rakhi (FLY ASH) 12 Surkhi 13 Stone Dust (Stone Dust, used in masonry work) 14 Ballast of stone / brick (FOR OTHER THAN ROAD WORK) 15 Stone 40 MM measured (grit broken by hand) (wides cut 1/11) 16 Stone 40 MM grit (broken by crusher) (wides cut 1/11) 17 Stone 20 MM grit (broken by crusher) ) 18 Stone 12 /10 /6 MM Grit (Broken by Crusher) 19 Brick Ballast 20 Road Works Material (5 Km. Lead Including) 21 63-40 mm (Broken by Crusher) (Wides Cut 1/11) 22 63-40 mm (Broken by Hand) (Wides Cut 1/11) 23 90-45 mm (Broken by Hand) (Wides Cut 1/11) 24 Kaveri Rubbish (Wides Cut 1/6) 25 Gravel (Wides Cut 1/6) 26 Kankar (Wides Cut 1/6) 27 Binding Material ( PI 4-6) (Wides Cut 1/6) 28 Brick (22.5 X 11 X 7.50 cm) 29 First Class (I CLASS) 30 Second Class (II CLASS) 31 Soiling/Kharanja/Masonry Stone 32 Masonry Beradda (RR) 33 Masonry Radda (CR) 34 Kharanja Soling (for flooring work upto 15 CM height) 35 Kharanja Soling (for road Kharanja work upto 23 CM height) 36 Jodhpuri type stone strip/champ/katli pieces (length 2-3, width 10-12, pearl 2.5-3.5) 37 Stone arch (FLAKY MATERIAL)(3-4 THICK & LENGTH & WIDTH1-2) 38 Sandstone (DPC, SILL, COPING, LINTEL, TAND, ALMIRAH, ETC) 39 Upto 25 MM thickness 40 25 - UPTO 40 MM THICKNESS 41 40- 50 MM THICKNESS 42 50 - 75 MM THICKNESS 43 75 - 100 MM THICKNESS 44 100 -150 MM THICKNESS 45 FLOORING / STRIP PAINTING KATLA STONE 46 FLOORING KATLA UPTO 35 MM THICK , min. 3 sqft or more area 47 KATLA FOR STRIP PAINTING 60 -75 mm THICKNESS , min. 3sqft or more area 48 Unpolished Rough Kota Stone 49 Upto 900 sq.cm 50 Upto 901 to 2300 sq.cm 51 More than 2300 sq.cm 52 Polished Kota Stone (One Side Polished) 53 Upto 900 sq.cm 54 Upto 901 to 2300 sq.cm 55 More than 2300 sq.cm 56 Marble Stone (Makrana Adanga 20mm Thick) 57 Upto 900 sq.cm 58 Upto 901 to 2300 sq.cm 59 More than 2300 sq.cm 60 Marble Chips 61 Marble Powder 62 Marble Stone (Rajnagar II Quality/Local 20mm Thick) 63 Upto 900 sq.cm 64 Upto 901 to 2300 sq.cm 65 More than 2300 sq. cm 66 Single petam size 100 x 75 mm 68 Double petam size 125 x 75 mm 69 Stone slab 70 Up to 1.5 m length , minimum 40 mm thick 71 1.5 m to 2.40 m length, minimum 50 mm thick 72 2.4 m to 3.0 m length , minimum 6 5 mm thick 73 above 3.0 m length, minimum 75 mmthick 74 Precast Tiles / Blocks 75 glazed size 30 x 45 cm 76 Mosaic Size - 40 mm thick 77 Vitrified Size- 60 x 60 cm 78 interlock tiles / brick / block for road work 79 Cement Interlocking Block M - 30 grade , 60 mm Thick 80 Cement Interlocking Block M - 30 grade ,80 mm Thick 81 Cement Interlocking Block M - 30 grade , 100 mm Thick 82 FR PVC Insulated Copper Conductor Single Core Cable ISI Marked 83 1.50 Sq.mm. 84 2.50 sq. mm. 85 0.50 sq mm 86 1.00 sq. mm. 87 4.00 sq. mm. 88 6.00 sq. mm. 89 Local wood with fittings (for doors, windows and furniture) 90 Mango 91 Babul 92 Others 93 Factory made doors (30mm thick, solid core single leaf) 94 Structural steel 95 Iron (Tor steel Fe 415 / 500 for reinforcement) 96 Winding wire 18 yards 97 Iron girders 98 Conical iron / square bar / strip / angle iron) 99 Barbed iron wire (size 12 guage wire and 12 guage strad / 12 guage wire and 14 guage strad / 14 guage 100 Mesh 101 Iron mesh (24 gauge, 14 mesh) 102 Cement concrete mesh Akash Patal 40 mm thick 103 Glass 104 3 mm thick glass 105 Colour - Paint 106 Enamel Paint 107 Decolorant (Water Bound) 108 Lime - For Painting (Aras / Kali) 109 Primer (For Iron / Wood) 110 Petroleum Products 111 Diesel HSD 112 Mobil Oil 113 Bitumen Shalitex Board (25 mm thick) 114 Plain Sheet 115 G.I. Sheet 22 Gauge (0.80 mm) 116 G.I. Sheet 24 Gauge (0.63 mm) 117 M.S. Sheet 22 Gauge (0.80 mm) 118 M.S. Sheet 24 Gauge (0.63 mm) 119 Corrugated Sheet 120 G.I. Sheet 1 mm thick 121 GI Sheet 22 Gauge (0.80 mm ) 122 Aswests Cement Sheet 6 mm ( 2.5 / 2.75 x 1m) 123 Other Sheets 124 PVC Sheet 1 mm thick ( Coloured / Plain ) 125 Green Yellow Literof Expo Sheet (183 x 90 ) 126 Pipes 127 GI 15 mm dia ( B Class) 128 GI 20 mm dia ( B Class) 129 GI 25 mm dia ( B Class) 130 AC 75 mm dia 131 AC 100 mm dia 132 PVC 90 mm Diameter (with ring) 133 P.V.C. 110 mm. Diameter (with ring) 134 P.V.C. 140 mm. Diameter (with ring) 135 P.V.C. 110 mm. (2.5 kg / sq. cm) with coupler 136 Sanitary 137 Indian W.C. 138 Orissa W.C. 139 European W.C. 140 FOOT REST 141 Porcelain Urinal 430 * 350 * 300 mm with coupler, bracket and P.V.C. waste pipe 142 Wash - Basin 450 * 300 mm with coupler, bracket and P.V.C. Waste pipe 143 Stone Bore (S.W.) pipe 100 mm dia, 0.6m long, 144 C.P. Pillar Cock (dia 15 mm ) (IS MARK ) 145 C.P. Bibb Cock (dia 15 mm ) (IS MARK ) 146 125 mm dia CP GRATTING 147 R.C.C. NP3 Hume Pipe with Collar 148 1200 mm dia 149 1000 mm dia 150 750 mm dia 151 600 mm dia 152 450 mm dia 153 300 mm dia 154 Steel Conduit ISI MARKED 155 20 mm dia 156 25 mm dia 157 Charcoal 158 P.V.C. WATER TANK WITH COVER (Conforming to IS : 12701 - 1989) 159 13/0.20 mm Twin Car PVC Blank with Flange Flexible Copper Cable 160 Steel Fasteners 6 mm x 75 mm 161 PVC CONDUIT ISI MARKED 162 25 mm Diameter 163 20 mm Diameter 164 JUNCTION BOX 165 20 mm Two Way 166 20 mm One Way 167 25 mm Two Way 168 20 mm One Way(PVC) 169 MODULE GI BOX 170 For 3 Modules 171 For 2 Modules 172 MODULE BASE COVER & PLATE 173 For 2 Modules 174 For 3 Module 175 Module Switch One Way, ISI MRKED 176 SP 15 /16 Ampere 177 SP 5 /6 Ampere 178 Modular Socket Outlet, ISI MRKED 179 3 Pin 5 /6 Ampere 180 6 Pin 15 /16 Ampere 181 MCB DB 182 2+2way, SPN, Single door 183 2+4way, SPN, Single door 184 2+6way, SPN, Single door 185 GI Pipe (Medium grade) 186 15.00 mm dia 187 40.00 mm dia 188 Copper wire 8 SWG (4.00 mm dia) (0.117 kg/m) 189 CI/MS cover plate, attached to frame of locking arrangement 190 Approved Equipment Hire Rate (with POL & Driver) 191 Diesel Road Roller 8 to 10 ton 192 Sheep Foot Roller 193 Truck 9 ton 194 Tractor (25 - 40 HP) 195 Tractor with Trolley 196 Tractor Water Tanker Capacity 4000 Liter Water 197 Cement Concrete Mixer 5 - 7 Cubic Feet 198 Pumping Set 15 H. P. 199 NIDDLE / PLATE VIBRATOR WITH OPERATOR 200 CAMEL CARTRID / BELL CARTRID WITH DRIVER 201 GRINDING MACHINE WITH OPERATOR (LARGE, MOTOR DRIVEN) 202 COMPRESSOR 203 HYDROLIC EXCAVATOR / JCB (BUCKET CAPCITY 0.4 CUM) 204 DUMPER 205 SCRAPER 206 SHUTTERING OF WOODEN FROST, WITH BEINGS AND OTHER MATERIALS, ADDED AT SITE, REMOVED AFTER THE SPECIFIED PERIOD 207 SHUTTERING OF PLY, WITH BEINGS AND OTHER MATERIALS, ADDED AT SITE, REMOVED AFTER THE SPECIFIED PERIOD 208 SHUTTERING OF IRON PLATE, WITH BEINGS AND OTHER MATERIALS, ADDED AT SITE, REMOVED AFTER THE SPECIFIED PERIOD 209 WATER AND PUMPING EXPENSES (FILLING) 210 Grinding machine with operator (small, hand operated) 211 Iron frame for well (diameter 3 m, height 75 cm) with TP, to be installed at site, removed after stipulated period 212 Cultivator etc

BRR:7519113 Tender For Gt Road Se Tiuri Pal Basti Road - Providing,laying,spreading and compacting stone aggregates of specific sizes (22.4-53 mm)to water bound macadam specification including spreading in uniform thickness,hand packing,rolling with smooth wheeI roller 80-100 KN in stages to proper grade and camber, applying and brooming requisite type of screening / binding materials to fill up the interstices of coarse aggregate,watering and compacting to the required density. WBM Grading-III as per Technical Spcification clause 405. 2 Providing and applying primer coat with bitumen emulsion (SS) on prepared surface of granular base including cleaning of road surface and spraying primer @ 0.70 kg/sqm using mechanical means as per Technical Specification Clause 502. 3 Providing and applying tack coat with bitumen (VG-10) using bitumen Emulsion pressure distributor @ 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with mechanicalbroom as per Technical Specification Clause 503. 4 Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen @1.46 kg/sqm to required line,grade and level to serve as wearing course on a previously prepared base including mixing in a suitable plant, laying and rolling with three wheel 80-100 kN static rollar capacity finished to required level and grades to be followed by seal coat of Type-C as per TechnicalSpecificationClause 508. 5 Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels grade and cross fall using Type-C with bitumen binder @ 0.65 kg/sqm including cost of bitumen as per Technical Specification Clause 510. 6 Construction of un-reinforced, dowel jointed, at expansion and construction joints only plain cement concrete pavement thicknees as per deigns over a prepared sub base with 43 grade cement or any other type as per clause 1501.2.2 M 30( Guide)coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less 0.2 cum capacity and appropriate weighbatcher using approved mix design,laid in approved fixed side fromwork (steel channel)laying fixing of 125 micron thick polythene firm wedge steel plate including leveling the fromwork as per drawing uploading the concrete withshovels rakes compacted using needle screed and polate vibrators and finished in sonnotous operation including provision of contraction and expention construction joints applying debonding strip primer scalant dowel bar near approaches to bridge /culvert and construction joints admixturesas approved curing compound (where specified) and water finishing to liner and grade as per drawing and technical specification clause 1501 7 Earthwork in cutting or in Patri in ordinary soil, excavation to be in the form of regular pits not exceeding 0.50m in depth and earthwork in embankment to be in 20 cm layers including ramming & dressing the surface to required levels and slopes and also including lift up to 1.50 m and lead upto 30 m. the earth cutting to be used in making embankment or to be deposited as spoil banks within 30m distance as directed by the Engineer-in-charge & as per S.I.No.253. 8 Maintance Cost of Ist year for P.C. Work @ 0.00% 9 Maintance Cost of Ist year for P.C. Work @ 1.5% 10 Maintance Cost of Ist year for P.C. Work @ 3.00% 11 Maintance Cost of Ist year for P.C. Work @ 4.50% 12 Maintance Cost of Ist year for P.C. Work @ 6.00% 13 Maintance Cost of Ist year for C.C. Work @ 0.00% 14 Maintance Cost of Ist year for C.C. Work @ 0.25% 15 Maintance Cost of Ist year for C.C. Work @ 0.50% 16 Maintance Cost of Ist year for C.C. Work @ 0.75% 17 Maintance Cost of Ist year for C.C. Work @ 1.00%

BRR:7519101 Tender For Special Repair Work Of Chatikara Parkham To Narayanpur Road In District Mathura - Providing, laying, spreading and compacting machine crushed stone ballastof approved quarry of 53~22.4mm size to water bound macadam of G-3 specification including spreading in uniform thickness, hand packing rolling with power roller 8 to 10 tonnes in stages to proper grade and camber applying and brooming with crushable screening material i.e. stone dust to fill-up the interstices of coarse aggregate, watering & rolling making necessary earthen bund to protect edges, lighting, guarding, barricadding etc. including the cost of all materials, labour, T & P etc. required for proper completion of work as per MORD specifications no 405. 2 Construction of un-reinforced, plain cement concretepavement thickness as per design, over a prepared sub base with 43 grade cement or any other type as per Clause 1501.2.2 M-30 (Grade), coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film wedges, steel plates including levelling the formwork as per drawing), spreading theconcrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished incontinuous operation including provision of contraction, expansion, construction and constructionl joints, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14 days, curing compund (where specified) and water finishing to lines and grade as per drawing and technical specification clause 1501. (For Mathura) 3 Construction of embankment with approved material obtained from availble land as permitted and approved byEngineer-in-Charge and as per Technical Specitaion Clause 301.3.4.1. with all lifts and leads,1000M spreading, grading to required slope and compacting to meet requirement of Tables 300.1and 300.2 as per Technical Specification clause 301.5

BRR:7519077 Tender For From Darapatti Lullur Pathaks house to Sarju Pradhans house - Providing,laying,spreading and compacting stone aggregates of specific sizes (22.4-53 mm)to water bound macadam specification including spreading in uniform thickness,hand packing,rolling with smooth wheeI roller 80-100 KN in stages to proper grade and camber, applying and brooming requisite type of screening / binding materials to fill up the interstices of coarse aggregate,watering and compacting to the required density. WBM Grading-III as per Technical Spcification clause 405. 2 Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer@ 0.70 kg/sqm using mechanical means as per Technical Specification Clause 503. 3 Providing and applying tack coat with bitumen (VG-10) using bitumen Emulsion pressure distributor @ 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with mechanicalbroom as per Technical Specification Clause 503. 4 Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm nominal size (22.4mm-11.2mm) & 11.2mm nominal size (13.2mm-5.6mm) aggregates either using penetration grade bitumen @1.46 kg/sqm to required line,grade and level to serve as wearing course on a previously prepared base including mixing in a suitable plant, laying and rolling with three wheel 80-100 kN static rollar capacity finished to required level and grades to be followed by seal coat of Type-C as per TechnicalSpecificationClause 508. 5 Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels grade and cross fall using Type-C with bitumen binder @ 0.65 kg/sqm including cost of bitumen as per Technical Specification Clause 510. 6 Cement Concrete Pavement Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501 7 Earthwork in cutting or in embankment in ordinary soil , excavation to be in the form or regular pits not exceeding 0.50m in depth and earthwork in embankment to be in 20 cm layers, including ramming & dressing the surface to equired levels and slopes and also including liftup to 1.5 m and lead up to 30 m. The earthcutting to be used in making embankment or tobe deposited as spoil banks within 30m distance as directed by the Engineer - in - charge.

BRR:7519076 Tender For Chhanoura Patti Bejavan Road To Nayepura Lal Bahadur Chouhan Ke Ghar Tak - Providing,laying,spreading and compacting stone aggregates of specific sizes (22.4-53 mm)to water bound macadam specification including spreading in uniform thickness,hand packing,rolling with smooth wheeI roller 80-100 KN in stages to proper grade and camber, applying and brooming requisite type of screening / binding materials to fill up the interstices of coarse aggregate,watering and compacting to the required density. WBM Grading-III as per Technical Spcification clause 405. 2 Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer@ 0.70 kg/sqm using mechanical means as per Technical Specification Clause 503. 3 Providing and applying tack coat with bitumen (VG-10) using bitumen Emulsion pressure distributor @ 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with mechanicalbroom as per Technical Specification Clause 503. 4 Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm nominal size (22.4mm-11.2mm) & 11.2mm nominal size (13.2mm-5.6mm) aggregates either using penetration grade bitumen @1.46 kg/sqm to required line,grade and level to serve as wearing course on a previously prepared base including mixing in a suitable plant, laying and rolling with three wheel 80-100 kN static rollar capacity finished to required level and grades to be followed by seal coat of Type-C as per TechnicalSpecificationClause 508. 5 Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels grade and cross fall using Type-C with bitumen binder @ 0.65 kg/sqm including cost of bitumen as per Technical Specification Clause 510. 6 Cement Concrete Pavement Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501 7 Earthwork in cutting or in embankment in ordinary soil , excavation to be in the form or regular pits not exceeding 0.50m in depth and earthwork in embankment to be in 20 cm layers, including ramming & dressing the surface to equired levels and slopes and also including liftup to 1.5 m and lead up to 30 m. The earthcutting to be used in making embankment or tobe deposited as spoil banks within 30m distance as directed by the Engineer - in - charge.

BRR:7519025 Tender For Civil maintenance work in various Type-5 and Type-6 houses located in Lower Dalibagh Colony - Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete. Semi rigid pipe 32mm dia/40 mm dia (17.28.1.1). 2 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass Screws and washers complete. (17.31). 3 Cutting Holes up to 15x15 cm in RCC floors and roofs for passing drain pipe etc , and repairing the holes after insertion of drain pipe etc with cement concrete 1:2:4 ( 1 cement:2coarse sand : 4 graded stone aggregate 20 mm nominal size ) , includinmg finishing complete so as to make it leak proof.(18.77) 4 Providing & fixing Float glass panes 5.00 mm thick glass panes (weigh not less than 12.50 kg/sqm)(DAR -9.7.7.2) 5 Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.(DAR -9.84) 6 Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia wire and 1.4 mm wide aperture with matching wood beading (DAR -9.7.8) 7 Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part 1) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply vereering with vertical grains or cross bands and face veneers on both faces of shutters:30 mm thick including ISI marked Stainless Steel bolt hinges with necessary(DAR -9.21.2) 8 Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).(DAR -9.53) 9 Providing and fixing ISI marked IS: 1341 M.S pressed butt hinges bright finished with necessary screws etc complete. 125x65x2.12 mm(DAR -9.55.1) 10 Providing and fixing ISI marked IS: 1341 M.S pressed butt hinges bright finished with necessary screws etc complete. 100x58x1.90 mm(DAR -9.55.2) 11 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378). 300x16(DAR -9.62.1) 12 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378). 250x16 mm (DAR -9.62.2) 13 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378). 250x10 mm(DAR -9.63.1) 14 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378). 200x10 mm(DAR -9.63.2) 15 Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete (Copper oxidised as per IS 1378). 125 mm (DAR -9.66.1) 16 Providing and fixing bright finished brass lower bolts (barrel type) with necessary screws etc complete. 250x10 mm(DAR -9.74.1) 17 Providing and fixing bright finished brass lower bolts (barrel type) with necessary screws etc complete. 200x10 mm(DAR -9.74.2) 18 Providing and fixing C.P.Brass bib cock of approved quality conforming to IS: 8931 15 mm nominal bore ( 18.49.1) 19 Providing and fixing C.P. brass long nose bib cock of approved quality conforming too IS standard and weighing not less than 810 gms , ( 15 mm nominal bore) 18.50.1 20 Providing and fixing C.P. Brass stop cock ( concealed) of standard design and of approved make conforming to IS 8931 ( 15 mm nominal bore )18.52.1 21 Providing and fixing C.P. Brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 ( m15 mm nominal bore)18.53.1 22 Providing and fixing water closet squaiting pan (indian type W.CPan) with 100 mm sand cast Iron P or S trap. 10 liter low level white P.V.C flushing cistern. Including flush pipe, with manually controlled device (handle lever) conformingto IS : 7231, with all fittings and fixtures complete. Including cutting and making good the walls and floors wherever required white Vitreous chin orissa pattern W.C. Pan of size 580x440 mm with integal typefoot rests. (17.1.1) 23 Providing and fixing wash basin with C.l. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. White Vitreous china Wash basin Size-630x450 mm with a pair of 15 mm C.P. brass pillar taps. (17.7.1) 24 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen Sink as per IS : 13983 with C.l. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever requried Kitchen sink with drain board. 510x1040mm bowl depth 250 mm (17.10.1.1) 25 Providing and fixing 8 mm dia C.P./S.S. jet with flexible tube upto 1 meter long with S.S. trangular plate to Eureopean typeW.C. of quality and make as approved by Engineer-in- charge.(17.16A). 26 Providing and fixing PVC low level flushing cistern with manually controlled device (handle lever) Conforming to IS : 7231with all fittings and fixtures complete 10 litre capacity white.(17.18.1). 27 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.DAR NO-15.56 28 12 mm thick Cement Plaster with Cement mortar in proportion of mix 1:4 (1 cement : 4 coarse sand). DAR-13.4.1 29 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete DSR 13.88 30 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.(D.S.R Item-13.80) 31 Distempering with 1st quality acrylic distemper(ready mixed ) new work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour.DSR-13.41.1 32 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. DSR 13.62.1

BRR:7519024 Tender For Various civil maintenance works in Driver Colony JOC Block and Transit Hostel accommodation located in Lower Dalibagh Colony - Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.(DAR -9.84) 2 Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia wire and 1.4 mm wide aperture with matching wood beading (DAR -9.7.8) 3 Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part 1) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply vereering with vertical grains or cross bands and face veneers on both faces of shutters:30 mm thick including ISI marked Stainless Steel bolt hinges with necessary(DAR -9.21.2) 4 Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).(DAR -9.53) 5 Providing and fixing ISI marked IS: 1341 M.S pressed butt hinges bright finished with necessary screws etc complete. 125x65x2.12 mm(DAR -9.55.1) 6 Providing and fixing ISI marked IS: 1341 M.S pressed butt hinges bright finished with necessary screws etc complete. 100x58x1.90 mm(DAR -9.55.2) 7 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378). 300x16(DAR -9.62.1) 8 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378). 250x16 mm (DAR -9.62.2) 9 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378). 250x10 mm(DAR -9.63.1) 10 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378). 200x10 mm(DAR -9.63.2) 11 Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete (Copper oxidised as per IS 1378). 125 mm (DAR -9.66.1) 12 Providing and fixing bright finished brass lower bolts (barrel type) with necessary screws etc complete. 250x10 mm(DAR -9.74.1) 13 Providing and fixing bright finished brass lower bolts (barrel type) with necessary screws etc complete. 200x10 mm(DAR -9.74.2) 14 Providing and fixing C.P.Brass bib cock of approved quality conforming to IS: 8931 15 mm nominal bore ( 18.49.1) 15 Providing and fixing C.P. brass long nose bib cock of approved quality conforming too IS standard and weighing not less than 810 gms , ( 15 mm nominal bore) 18.50.1 16 Providing and fixing C.P. Brass stop cock ( concealed) of standard design and of approved make conforming to IS 8931 ( 15 mm nominal bore )18.52.1 17 Providing and fixing C.P. Brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 ( m15 mm nominal bore)18.53.1 18 Providing and fixing water closet squaiting pan (indian type W.CPan) with 100 mm sand cast Iron P or S trap. 10 liter low level white P.V.C flushing cistern. Including flush pipe, with manually controlled device (handle lever) conformingto IS : 7231, with all fittings and fixtures complete. Including cutting and making good the walls and floors wherever required white Vitreous chin orissa pattern W.C. Pan of size 580x440 mm with integal typefoot rests. (17.1.1) 19 Providing and fixing wash basin with C.l. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. White Vitreous china Wash basin Size-630x450 mm with a pair of 15 mm C.P. brass pillar taps. (17.7.1) 20 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen Sink as per IS : 13983 with C.l. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever requried Kitchen sink with drain board. 510x1040mm bowl depth 250 mm (17.10.1.1) 21 Providing and fixing 8 mm dia C.P./S.S. jet with flexible tube upto 1 meter long with S.S. trangular plate to Eureopean typeW.C. of quality and make as approved by Engineer-in- charge.(17.16A). 22 Providing and fixing PVC low level flushing cistern with manually controlled device (handle lever) Conforming to IS : 7231with all fittings and fixtures complete 10 litre capacity white.(17.18.1). 23 Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete. Semi rigid pipe 32mm dia/40 mm dia (17.28.1.1). 24 Cutting Holes up to 15x15 cm in RCC floors and roofs for passing drain pipe etc , and repairing the holes after insertion of drain pipe etc with cement concrete 1:2:4 ( 1 cement:2coarse sand : 4 graded stone aggregate 20 mm nominal size ) , includinmg finishing complete so as to make it leak proof.(18.77) 25 Providing & fixing Float glass panes 5.00 mm thick glass panes (weigh not less than 12.50 kg/sqm)(DAR -9.7.7.2) 26 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass Screws and washers complete. (17.31). 27 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.DAR NO-15.56 28 12 mm thick Cement Plaster with Cement mortar in proportion of mix 1:4 (1 cement : 4 coarse sand). DAR-13.4.1 29 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete DSR 13.88 30 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.(D.S.R Item-13.80) 31 Distempering with 1st quality acrylic distemper(ready mixed ) new work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour.DSR-13.41.1 32 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. DSR 13.62.1

BRR:7518925 Tender For Annual Plan-Panachikadugp :72/2024-25-Kattampakku Illiparampu Road Concrete Inward 4 -General Civil Work; 1 ROAD CONCREATING 2 OD281272/2024-2025:Surface dressing of the ground including removing vegetation and in equalities not exceeding 15cm deep and disposal of rubbish lead up to 50m and li9ft up to 1.5m .all kinds of soil 3 75.8.1.1:Providing plain/reinforced concrete(1 cement:2 fine aggregate: 4 course aggregate) forsubstructure as per drawings and technical specifications Clause 802, 803, 1202 & 1203as required including compaction, finishing and tamping etc .complete. Max. size ofcourse aggregate not exceeding 25mm , mixed in concrete mixer etc complete as perspecification (i) Nominal mix (1:2:4)

BRR:7518922 Tender For General-Panachikadu Gp 82/25-: Kuryanparambu-Chooravadi Road Re-Concreting Ward-5-General Civil Work; 1 ROADRE CONCRETING 2 OD356464/2024-2025:Engaging man coolie for miscellaneous work 3 OD356465/2024-2025:Surface dressing of the ground including removing vegetation and in equalities not exceeding 15cm deep and disposal of rubbish lead up to 50m and li9ft up to 1.5m .all kinds of soil 4 75.8.1.1:Providing plain/reinforced concrete(1 cement:2 fine aggregate: 4 course aggregate) forsubstructure as per drawings and technical specifications Clause 802, 803, 1202 & 1203as required including compaction, finishing and tamping etc .complete. Max. size ofcourse aggregate not exceeding 25mm , mixed in concrete mixer etc complete as perspecification (i) Nominal mix (1:2:4) 5 75.8.1.1.A:Providing Plain cement concrete for wearing coat CC 1:2:4 (1 cement: 2 fine aggregate:4 course aggregate) laid to required slope as required including compaction, finishingand tamping etc .complete. Max. size of course aggregate not exceeding 25mm , mixedin concrete mixer etc complete as per specification (i) Nominal mix (1:2:4)

BRR:7518825 Tender For Annual Plan-TGP 2024-25 PRO NO:497/25-Karimathil Unnathi DWSS[(Ward:14)(RS 3.00 Lakh) TSP]-General Civil Work - DRINKING WATER SUPPLY 2 2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil 3 OD347821/2024-2025:DRY RUBBLE MASONRY _ Dry rubble without concrete levelling course masonry with good quality blasted rubble including packing to compactness to lines and levels cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site.(Old Specification code: 60.7.1) 4 50.18.9.3.2:Providing and fixing PVC pipes includes jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 25 mm dia 10KGF/cm2 5 50.18.9.4.1:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.32 mm dia 10.Kgf/cm2 6 50.18.9.5.1:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching refilling & testing of joints complete as per direction of Engineer in Charge 40 mm dia 10Kgf/cm2 7 50.18.9.6.1:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 50 mm dia 10Kgf/cm2 8 50.18.9.8.2:Providing and fixing PVC pipes includings of pipes with one step PVC solvent cement, trenching and refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 4 Kgf/cm2 9 18.57.2:Providing and fixing PTMT, push cock of approved quality and colour.15 mm nominal bore, 80 mm long weighing not less than 46 gms 10 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) 11 5.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 12 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more 13 4.3.1:Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns 14 OD379312/2024-2025:Supplying and Fixing including installation of good quality and ISI mark Submersible pump set of good and reputed brand (like Kirloskar, V-Guard, Crompton etc) with metal impeller including all fittings such as panel board, switch etc and including labour charge for fittings. 1.50 hp Submersible pump set 15 18.48:Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 16 OD379313/2024-2025:NAME BOARD:Providing and fixing name board of size 60x50 cm with frame 40x20x16 G square rod including letter,primingwith synthetic enamel

BRR:7517449 Bids Are Invited For Electronic Weighing Scale With Ss304 Platform , Electronic Weighing Scales Total Quantity : 1

BRR:7517348 Bids Are Invited For Micro Weighing Balance With Licensed Software Total Quantity : 1

BRR:7517346 Bids Are Invited For For Esp And Silo Of Ash Handling Plant 150806280146 , 150806280163 , 150806280164 , 150806280050 , 150806280165 Fluidizing Air Blower Without Motor For Silo, Model-78Ac, Capacity :800 Meter Cube-Hour, Pressure: 0.7Kg-Cm2, Blower Speed:1169 Rpm,Motor Power:40Hp, Suction Filter For Fluidizing Blower Of Silo Model No.- 78Ac, Make- Kay International Ltd., Discharge Nrv For Silo Fluidizing Blower , Centrifugal Fan Blower Total Quantity : 17

BRR:7516761 Bids Are Invited For Microsemi-Microanalytical Weighing Balance (Q2) Total Quantity : 1

BRR:7515265 Supplying, Fitting And Fixing Of Weight Machine At Harua Pwm Unit Under Suti I Development Block Murshidabad , Supplying, Fitting And Fixing Of Wight Machine At Harua Pwm Unit Under Suti-I Development Block, Murshidabad. Brand: Make Brand As Per Instruction Of Eic, Recommended Uses For Product: General Grocery Stores, Kitchens, Parcel Weighing, Warehouses, Retail Weighing, Industries, General Grocery Stores, Kitchens, Parcel Weighing, Warehouses, Retail Weighing, Industries, Special Feature: Non Slip Platform, Backlit Display, Tare Function, Display Type: Led, Weight Limit: 500 Kilograms, Form Factor: Heavy Duty Commercial Platform Scale, Material: Metal, Readout Accuracy: 50 Grams, Item Weight: 32 Kilograms, Weigh Scale Type: Floor Scale, Measurement Type: Kilograms, Grams, Product Dimensions : 60 X 60 X 90 Cm; 32 Kg, Item Height: 90 Centimeters, Item Width: 60 Centimeters, Power Source: Ac/Dc, Included Components: Weighing Scale, Charger, Calibration/ Verification Certificate & Manual, Batteries Included.

BRR:7515029 Work Of Modification Of Manual Flap Gate To Electrically Operated Flap Gate Of R4 Discharge Chute At Old Silo Of Gevra Project.

BRR:7514998 Supply And Installation Of Gym Equipments For Daitari Region , Description , Fully Commercial Rated Cross Trainer (Specifications As Per Annexure 2: Special Conditions Of Contract) , Fully Commercial Multi Gym (Specifications As Per Annexure 2: Special Conditions Of Contract) , Imported Dumpbell Set (Specifications As Per Annexure 2: Special Conditions Of Contract) , Fully Commercial Rated Adj. Bench (Specifications As Per Annexure 2: Special Conditions Of Contract) , Fully Commercial Rated Barrel Rack (Specifications As Per Annexure 2: Special Conditions Of Contract) , Fully Commercial Rated Spin Bike (Specifications As Per Annexure 2: Special Conditions Of Contract) , Fully Commercial Ac Motorize Treadmill(Specifications As Per Annexure 2: Special Conditions Of Contract) , Weight Lifting Set (Specifications As Per Annexure 2: Special Conditions Of Contract) , Kettle Bell (Specifications As Per Annexure 2: Special Conditions Of Contract) , Gym Floor Mat Inter Locked With Fixing (Specifications As Per Annexure 2: Special Conditions Of Contract) , Multifunctional Smith Functional Trainer (Specifications As Per Annexure 2: Special Conditions Of Contract) , Squat Rack (Specifications As Per Annexure 2: Special Conditions Of Contract) , Aerobic Steps(Specifications As Per Annexure 2: Special Conditions Of Contract) , Thera/ Resistant Band Set (Specifications As Per Annexure 2: Special Conditions Of Contract) , Gym Ball Set (Specifications As Per Annexure 2: Special Conditions Of Contract) , Weighing Scale Digital (Specifications As Per Annexure 2: Special Conditions Of Contract) , Artificial Grass Mat-35Mm (Specifications As Per Annexure 2: Special Conditions Of Contract) , Pool Table (Specifications As Per Annexure 2: Special Conditions Of Contract) , Fossball (Specifications As Per Annexure 2: Special Conditions Of Contract) , Table Tennis Table (Specifications As Per Annexure 2: Special Conditions Of Contract) => Limited

BRR:7514726 Tender For Civil maintenance and painting work in housing no. 07 and 9A, 10A situated at Kalidas Marg - Providing and fixing ISI marked oxidised M.S Tower bolt black finish (Barreltype) with necessary screws etc complete Copper Oxidised as per lS 1378, 250x10 mm(DAR -9.63.1) 2 Providing and fixing bright finished brass lower bolts (barrel type) with necessary screws etc complete. 250x10 mm (DAR -9.74.1) 3 Providing and fixing bright finished brass lower bolts (barrel type) with necessary screws etc complete. 200x10 mm (DAR -9.74.2) 4 Providing and fixing C.P.Brass Stop cock (Concealed) Standerd desingn and approved make conforming to IS:8931. 15 mm nominal bore ( 18.52.1) 5 Providing and fixing C.P.Brass Angle Valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15 mm nominal bore ( 18.53.1) 6 Providing and fixing C.P.Brass extentsion nipple (Size-15x50mm) of approved make and quality as per direction of engineer-in-charge. ( 18.53A) 7 Providing and fixing ball valve brass (brass ) of approved quality , high or low pressure, with plastic floats complete: ( 20 mm nominal bore) 18.18.2 8 Providing and fixing ball valve brass (brass ) of approved quality , high or low pressure, with plastic floats complete: ( 25 mm nominal bore) 18.18.3 9 Providing and fixing G.I. Union in G.I. pipe incluliding cutting cutting and threading the pipe and making long screw etc, complete, New work, ( 15 mm nominal bore ) 18.46.1 10 Providing and fixing G.I. Union in G.I. pipe incluliding cutting cutting and threading the pipe and making long screw etc, complete, New work, ( 25 mm nominal bore ) 18.46.3 11 Providing and fixing G.I. Union in G.I. pipe incluliding cutting cutting and threading the pipe and making long screw etc, complete, New work, ( 32 mm nominal bore ) 18.46.4 12 Providing and fixing ISI markedflush door Shutters Conforming to IS : 2202 (Part I) Non decorative type core of block board construction with frame lst class hard wood and well matched commercial 3 ply Veneening with vertical graints or cross brand and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt Hinges with Necessary Screws.DAR N0-9.21.1, 13 Providing And FixingFly Proof galvanized M.S. wire gauge to windows and Clerestory window using wire gauge with average widht of aperture 1.4 mm both directions with wire of dia 0.63 mm all complete with second class teak wood beading 62x19 mm. DAR No-9.51.1, 14 Providing And Fixing Float Glass Panes 4.0 mm thick(Weight not less than 10.00 kg/Sqm), (DAR-9.7.7.1) 15 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door widht upto 700 mm), with necessary accessories and screws etc. complete. DAR-9.83, 16 Providing and fixing brass Curtain Rods of wall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete. 25 mm dia meter. DAR-14.28.2, 17 Providing and Fixing of UV Stabilised Fiberglass reinforced Plastic Sheet Roofing up to any Pitch, including Fixing with Polymer Coated J or L hooks, bolts & nuts 8 mm dia, G.l. Plain/bitumen Washers Complete but excluding the Cost of Purlins, Rafters, Trusses etc. the Sheets shall be manufactured out of 2400 TEX Panel Roving Incorporating Minimum 0.3%, Ultra-Violet Stabiliser in resing system under approximately 2400 PSl and hot Cured. they Shall be of Uniform Pigmentation and thickness without air Pockets and shall Conform to IS 10192 and IS 12866. the Sheets Shall be Opaque or translucent, Clear or Pigmented Textured or Smooth as Specified. 2 mm thick Corrugated (2.5 or 4.2 or 6) or Step-Down (2 or 3 or 6 ) as Specified.DAR N0-12.47.1, 18 Providing and fixing G.I. Pipe complete with G.I. fittings and clamps, including making good the walls etc. Concealed Pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall ( 20 mm nominal bore ) 18.11.2 19 Providing and fixing G.I. Union in existing G.I. pipe line, cutting and incluldingthreading the pipe and making long screws, including excavation, refilling the earth or cuttingof wall and making good the same complete wherever required ( 15 mm nominal bore ) 18.47.1, 20 Providing and fixing G.I. Union in existing G.I. pipe line, cutting and incluldingthreading the pipe and making long screws, including excavation, refilling the earth or cuttingof wall and making good the same complete wherever required( 20 mm nominal bore ) 18.47.2, 21 Providing and fixing wash basin with C.l. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. Stainless Steel A lSl-304(18/8) Wash basin Size-530x345 mm with single 15 mm C.P. brass pillar tap. (17.7.11) 22 Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete. Flexible pipe 32mm dia(17.28.2.1). 23 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass Screws and washers complete. (17.31). 24 Providing and fixing 600x120x5 mm glass Self with edge round off, supported on anodiesd aluminium angle frame with c.p. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc. complete.(17.33). 25 Providing and fixing TOILET PAPER HOLDERC.P. Brass (17.34.1). 26 Providing and fixing water closet Squatting pan (Indian Type w.c. Pan)with 100 mm sand cast Iron P or s Trep, 10 liter low level white P.V.C. Flushing Cistern, including Flush Pipe, with manually Controlled device (Handle lever) Conforming To IS :7231 with all fittings and fixtures complete, including cutting and making good the walls andfloors wherever required white Vitreous china Orissa pang Size 580x440 mm with integral type foot rests. DSR-17.1.1, 27 Providing and fixing Chlorinated Polyyinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plains & brass threated fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joints of pipe and fitting with one step CPVC solventcement and the cost of cuttings chases and making good the same including testing of joints complete as per direction of Engineer Incharge. concealed work, including cutting chases and making good the walls etc. (15mm nominal dia pipe )18.8.1, 28 Providing and fixing Chlorinated Polyyinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plains & brass threated fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joints of pipe and fitting with one step CPVC solventcement and the cost of cuttings chases and making good the same including testing of joints complete as per direction of Engineer Incharge. concealed work. including cutting chases and making good the walls etc. (20mm nominal dia pipe )18.8.2, 29 Providing and fixing Chlorinated Polyyinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plains & brass threated fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joints of pipe and fitting with one step CPVC solventcement and the cost of cuttings chases and making good the same including testing of joints complete as per direction of Engineer Incharge. concealed work. including cutting chases and making good the walls etc. (25mm nominal dia pipe )18.8.3, 30 Providing and fixing Chlorinated Polyyinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plains & brass threated fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joints of pipe and fitting with one step CPVC solventcement and the cost of cuttings chases and making good the same including testing of joints complete as per direction of Engineer Incharge. concealed work. including cutting chases and making good the walls etc. (32mm nominal dia pipe )18.8.4, 31 Providing and fixing Chlorinated Polyyinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threated fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joints of pipes & fitting with one step CPVC solventcement and testing of joints complete as per direction of Engineer -In-charge. Internal work -Exposed on wall (20 mm nominal dia pipe )18.7.2, 32 Providing and fixing Chlorinated Polyyinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threated fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joints of pipes & fitting with one step CPVC solventcement and testing of joints complete as per direction of Engineer -In-charge. Internal work -Exposed on wall (25 mm nominal dia pipe )18.7.3, 33 Providing and fixing G.I. Pipe complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. inernal work - exposed on wall ( 15 mm nominal bore ) 18.10.1 34 Providing and fixing G.I. Pipe complete with G.I. fittings and clamps, i/c cutting and making good the walls etc etc inernal work - exposed on wall. ( 20 mm nominal bore ) 18.10.2 , 35 Providing and fixing G.I. Pipe complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. inernal work - exposed on wall. ( 25 mm nominal bore ) 18.10.3, 36 Providing and fixing G.I. Pipe complete with G.I. fittings and clamps, including making good the walls etc. Concealed Pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall ( 15 mm nominal bore ) 18.11.1 37 Providing and fixing C.P.Brass bib cock of approved quality conforming to IS: 8931 15 mm nominal bore ( 18.49.1) 38 Providing and fixing C.P.Brass long nose bib cock of approved quality conforming to IS Standerd and weighing not less 810 gms. 15 mm nominal bore ( 18.50.1) 39 Providing and fixing C.P.Brass long body bib cock of approved quality conforming to IS Standerd and weighing not less 690 gms. 15 mm nominal bore ( 18.51.1) 40 Dismantling Old Plaster or SkirtingRacking out joint and cleaning the surface for plasterincluding disposal of rubbish to the dumping ground within 50 metars lead. DAR No-15.56, 41 12 mm thick Cement Plaster with Cement mortar in proportion of mix 1:4 (1 cement : 4 coarse sand). DAR-13.4.1, 42 Removing White or Colour wash by Scrapping and sand papering and preparing the surface smoothincluding necessary repairs to scratches etc. complete.DSR-13.88, 43 Providing and Applying white Cement based Putty of average thickness 1 mm. of approved brand and manufacture. Over the Plastered wall Surface to Prepare the Surface even and Smooth Complete. (DSR-13.80), 44 Wall Painting with Premium acrylic emulsion paint of Interior grade, having VOC (VolatileOrganic Compound) Content less than 50 grams/litre of approved brand and manufacture, lncluding applying additional coats wherever required, to achieve even shade and colour. Two Coat, DSR.N0-13.83.2), 45 Painting with Synthetic enamel paint of approved brand and manufacture of required colour to give an even shade two of more coatson new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. DSR.N0-13.62.1), 46 Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. Note - item to be applicable in urban areas having directions for restricted hours for movement/plying of load carrying motor vehicle of 3.5 cum or more. DAR-1.1.18,

BRR:7514725 Tender For Civil maintenance and painting work in residence no. 11, 12, 12A situated at Kalidas Marg - Providing and fixing bright finished brass lower bolts (barrel type) with necessary screws etc complete. 250x10 mm (DAR -9.74.1) 2 Providing and fixing ISI marked oxidised M.S Tower bolt black finish (Barreltype) with necessary screws etc complete Copper Oxidised as per lS 1378, 250x10 mm(DAR -9.63.1) 3 Providing and fixing bright finished brass lower bolts (barrel type) with necessary screws etc complete. 200x10 mm (DAR -9.74.2) 4 Providing and fixing C.P.Brass Stop cock (Concealed) Standerd desingn and approved make conforming to IS:8931. 15 mm nominal bore ( 18.52.1) 5 Providing and fixing C.P.Brass Angle Valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15 mm nominal bore ( 18.53.1) 6 Providing and fixing C.P.Brass extentsion nipple (Size-15x50mm) of approved make and quality as per direction of engineer-in-charge. ( 18.53A) 7 Providing and fixing ball valve brass (brass ) of approved quality , high or low pressure, with plastic floats complete: ( 20 mm nominal bore) 18.18.2 8 Providing and fixing ball valve brass (brass ) of approved quality , high or low pressure, with plastic floats complete: ( 25 mm nominal bore) 18.18.3 9 Providing and fixing G.I. Union in G.I. pipe incluliding cutting cutting and threading the pipe and making long screw etc, complete, New work, ( 15 mm nominal bore ) 18.46.1 10 Providing and fixing G.I. Union in G.I. pipe incluliding cutting cutting and threading the pipe and making long screw etc, complete, New work, ( 25 mm nominal bore ) 18.46.3 11 Providing and fixing G.I. Union in G.I. pipe incluliding cutting cutting and threading the pipe and making long screw etc, complete, New work, ( 32 mm nominal bore ) 18.46.4 12 Providing and fixing ISI markedflush door Shutters Conforming to IS : 2202 (Part I) Non decorative type core of block board construction with frame lst class hard wood and well matched commercial 3 ply Veneening with vertical graints or cross brand and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt Hinges with Necessary Screws.DAR N0-9.21.1, 13 Providing And FixingFly Proof galvanized M.S. wire gauge to windows and Clerestory window using wire gauge with average widht of aperture 1.4 mm both directions with wire of dia 0.63 mm all complete with second class teak wood beading 62x19 mm. DAR No-9.51.1, 14 Providing And Fixing Float Glass Panes 4.0 mm thick(Weight not less than 10.00 kg/Sqm), (DAR-9.7.7.1) 15 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door widht upto 700 mm), with necessary accessories and screws etc. complete. DAR-9.83, 16 Providing and fixing brass Curtain Rods of wall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete. 25 mm dia meter. DAR-14.28.2, 17 Providing and Fixing of UV Stabilised Fiberglass reinforced Plastic Sheet Roofing up to any Pitch, including Fixing with Polymer Coated J or L hooks, bolts & nuts 8 mm dia, G.l. Plain/bitumen Washers Complete but excluding the Cost of Purlins, Rafters, Trusses etc. the Sheets shall be manufactured out of 2400 TEX Panel Roving Incorporating Minimum 0.3%, Ultra-Violet Stabiliser in resing system under approximately 2400 PSl and hot Cured. they Shall be of Uniform Pigmentation and thickness without air Pockets and shall Conform to IS 10192 and IS 12866. the Sheets Shall be Opaque or translucent, Clear or Pigmented Textured or Smooth as Specified. 2 mm thick Corrugated (2.5 or 4.2 or 6) or Step-Down (2 or 3 or 6 ) as Specified.DAR N0-12.47.1, 18 Providing and fixing G.I. Pipe complete with G.I. fittings and clamps, including making good the walls etc. Concealed Pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall ( 20 mm nominal bore ) 18.11.2 19 Providing and fixing G.I. Union in existing G.I. pipe line, cutting and incluldingthreading the pipe and making long screws, including excavation, refilling the earth or cuttingof wall and making good the same complete wherever required ( 15 mm nominal bore ) 18.47.1, 20 Providing and fixing G.I. Union in existing G.I. pipe line, cutting and incluldingthreading the pipe and making long screws, including excavation, refilling the earth or cuttingof wall and making good the same complete wherever required( 20 mm nominal bore ) 18.47.2, 21 Providing and fixing wash basin with C.l. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. Stainless Steel A lSl-304(18/8) Wash basin Size-530x345 mm with single 15 mm C.P. brass pillar tap. (17.7.11) 22 Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete. Flexible pipe 32mm dia(17.28.2.1). 23 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass Screws and washers complete. (17.31). 24 Providing and fixing 600x120x5 mm glass Self with edge round off, supported on anodiesd aluminium angle frame with c.p. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc. complete.(17.33). 25 Providing and fixing TOILET PAPER HOLDERC.P. Brass (17.34.1). 26 Providing and fixing water closet Squatting pan (Indian Type w.c. Pan)with 100 mm sand cast Iron P or s Trep, 10 liter low level white P.V.C. Flushing Cistern, including Flush Pipe, with manually Controlled device (Handle lever) Conforming To IS :7231 with all fittings and fixtures complete, including cutting and making good the walls andfloors wherever required white Vitreous china Orissa pang Size 580x440 mm with integral type foot rests. DSR-17.1.1, 27 Providing and fixing Chlorinated Polyyinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plains & brass threated fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joints of pipe and fitting with one step CPVC solventcement and the cost of cuttings chases and making good the same including testing of joints complete as per direction of Engineer Incharge. concealed work, including cutting chases and making good the walls etc. (15mm nominal dia pipe )18.8.1, 28 Providing and fixing Chlorinated Polyyinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plains & brass threated fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joints of pipe and fitting with one step CPVC solventcement and the cost of cuttings chases and making good the same including testing of joints complete as per direction of Engineer Incharge. concealed work. including cutting chases and making good the walls etc. (20mm nominal dia pipe )18.8.2, 29 Providing and fixing Chlorinated Polyyinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plains & brass threated fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joints of pipe and fitting with one step CPVC solventcement and the cost of cuttings chases and making good the same including testing of joints complete as per direction of Engineer Incharge. concealed work. including cutting chases and making good the walls etc. (25mm nominal dia pipe )18.8.3, 30 Providing and fixing Chlorinated Polyyinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threated fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joints of pipes & fitting with one step CPVC solventcement and testing of joints complete as per direction of Engineer -In-charge. Internal work -Exposed on wall (25 mm nominal dia pipe )18.7.3, 31 Providing and fixing G.I. Pipe complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. inernal work - exposed on wall ( 15 mm nominal bore ) 18.10.1 32 Providing and fixing G.I. Pipe complete with G.I. fittings and clamps, i/c cutting and making good the walls etc etc inernal work - exposed on wall. ( 20 mm nominal bore ) 18.10.2 , 33 Providing and fixing G.I. Pipe complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. inernal work - exposed on wall. ( 25 mm nominal bore ) 18.10.3, 34 Providing and fixing G.I. Pipe complete with G.I. fittings and clamps, including making good the walls etc. Concealed Pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall ( 15 mm nominal bore ) 18.11.1 35 Providing and fixing C.P.Brass bib cock of approved quality conforming to IS: 8931 15 mm nominal bore ( 18.49.1) 36 Providing and fixing C.P.Brass long nose bib cock of approved quality conforming to IS Standerd and weighing not less 810 gms. 15 mm nominal bore ( 18.50.1) 37 Providing and fixing C.P.Brass long body bib cock of approved quality conforming to IS Standerd and weighing not less 690 gms. 15 mm nominal bore ( 18.51.1) 38 Dismantling Old Plaster or SkirtingRacking out joint and cleaning the surface for plasterincluding disposal of rubbish to the dumping ground within 50 metars lead. DAR No-15.56, 39 12 mm thick Cement Plaster with Cement mortar in proportion of mix 1:4 (1 cement : 4 coarse sand). DAR-13.4.1, 40 Removing White or Colour wash by Scrapping and sand papering and preparing the surface smoothincluding necessary repairs to scratches etc. complete.DSR-13.88, 41 Providing and Applying white Cement based Putty of average thickness 1 mm. of approved brand and manufacture. Over the Plastered wall Surface to Prepare the Surface even and Smooth Complete. (DSR-13.80), 42 Wall Painting with Premium acrylic emulsion paint of Interior grade, having VOC (VolatileOrganic Compound) Content less than 50 grams/litre of approved brand and manufacture, lncluding applying additional coats wherever required, to achieve even shade and colour. Two Coat, DSR.N0-13.83.2), 43 Painting with Synthetic enamel paint of approved brand and manufacture of required colour to give an even shade two of more coatson new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. DSR.N0-13.62.1), 44 Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. Note - item to be applicable in urban areas having directions for restricted hours for movement/plying of load carrying motor vehicle of 3.5 cum or more. DAR-1.1.18,

BRR:7514672 Purchase of weighing machine for Anganvadies

BRR:7514670 Material Supply For , Stone Aggregate(Single Size): 40 Mm Nominal Size , Stone Aggregate(Single Size):20 Mm Nominal Size , Stone Aggregate(Single Size): 10 Mm Nominal Size , Stone Aggregate(Single Size): 6 Mm Nominal Size , Coarse Sand (Zone Iii) , Portland Cement , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With Hopper , Vibrator (Needle Type 40 Mm) , Stone For Masonry Work , Twisted Steel/Deformed Bars , Solid Blocks Of Size 30X20x15cm , Fine Sand (Zone Iv) , Water Thinnable Cement Primer For Interior Wall Surface, Having Voc Content Less Than 50 Gms/Litre , Acrylic Exterior Paint , Exterior Primer , Flats Up To 10 Mm In Thickness , Welding By Electric Plant , Red Oxide Zinc Chromate Primer , Structural Steel Such As Tees, Angles, Channels And R.S. Joists , Adjustable Telescopic Prop 3 M (2.02-3.75M) , Beam Clamp 300-380 Mm (450-1070 Mm) , Aracanut Post , Bamboo/Kallanmula , G.I Pipes 50 Mm Dia , G.I. Pipes 40 Mm Dia , Gi Trafford Profile Sheet 0.35Mm Thick , Stainless Steel Screws 50 Mm , Pvc Bend 63 Mm Dia , Pvc Tee 63X63x63 Mm Dia , Pvc End Cap 63 Mm Dia , Pvc Elbow 63 Mm Dia , Pvc Pipe 63 Mm Outer Dia. 4 Kgf/Cm2 , Pvc Reducer 63X50 Mm Dia , Pvc Vent Cowl 63 Mm Dia , Polyethylene Water Storage Tank With Cover And Suitable Locking Arrangemnet , Wall Form Panel 1250X500 Mm , 100 Mm Channel Shoulder 2.5 M Long , Double Clip (Bridge Clip) , Single Clip , M.S. Tube 40 Mm Dia , Laterate Stone Of Size 40X20x15cm , Solid Blocks Of Size 30X20x20cm , Galvanised Steel Corrugated Sheets , Galvanised Steel Bolts & Nuts 6 Mm Dia And 25 Mm Long Round Head With Slots , Galvanised Steel J Or L Hooks 8 Mm Dia , G.I Limpet Washer , Bitumen Washer , Roofing Paint For Iron Sheets In Red Colour , Galvanised Wire Mesh Of Average Width Of Aperture 1.4 And Nominal Dia. Of Wire 0.63 Mm , Wire Nails , Mild Steel Plates , Mild Steel Rivets , 20 Mm Dia Holding Down Bolts , Quarry Waste , Corner Angle 45X45x5 Mm 1.50 M Long , Bamboo 25 Mm Dia 2.5 Meter Long , Separation Membrane Of Impermeable Plastic Sheeting 125 Micron Thick , Boulder 50 Mm To 200 Mm , Crates Made Of Mesh Type 10X12 (D=100Mm) Zinc Coated (Mash Wire Diameter 3.00 Mm) , Green Net 75% Shade , Polyurethene Bags , Royalty For Good Earth , Interlocking C.C. Paver Block (80 Mm Thick, M-30) , Precast Chequered Cement Tiles 22 Mm Thick Dark Shade Using Ordinary Cement , Mild Steel Tubes Hot Finished Welded Type , 200 Mm Aluminium Aldrop , Second Class Kail Wood In Planks , Second Class Kail Wood In Scantling , Safeda Ballies 125 Mm Diameter , Mild Steel Round Bar 12 Mm Dia And Below , Pvc Pipe 15 Mm Outer Dia. 12Kgf/Cm2 , Ceramic Glazed Tiles Ist Quality Minimum Thickness 5 Mm In All Colours Shades And Designs Except Burgundy, Bottle Green Black , Ceramic Glazed Tiles Ist Quality 300 X 300 Mm In All Shades And Designs Of White, Ivory, Grey, Fume Red Brown Etc. , Vitreous China Orrisa Type W.C. Pan Size 580 Mm , Vitrified Floor Tile 60X60 Cm , Hollock Ballies 125 Mm Diameter , Adjustable Span Eso+Si (2.35-3.40) , Anjili Wood Scantls , Bright Finished Or Black Enameled Mild Steel Butt Hinges 100X58x1.90 Mm , Bright Finished Or Black Enameled Mild Steel Butt Hinges 50X37x1.50 Mm , Bright Finished Or Black Enameled Mild Steel Screws 40 Mm , Bright Finished Or Black Enameled Mild Steel Screws 20 Mm , Anjili Wood Planks , Float Glass Sheet Of Nominal Thickness 4 Mm (Weight Not Less Than 10 Kg/Sqm) , Factory Made Door Frame Size 50X47 Mm With Wall Thickness 5 Mm Made Of Single Piece Extruded Profile , 35 Mm Thick Factory Made Solid Panel Pvc Door Shutter Of Single Piece Extruded Profile Non Decorative Finished (Matt Finished) , Powder Coated M.S. Butt Hinges 100 Mm X58 Mm X 1.9 Mm , Anodised Aluminium Handles 125 Mm With Plate 175 X 32 Mm , Chromium Plated Brass Screws 25 Mm , Iron Hooks & Eyes 100 Mm , Anodised Aluminium Tower Bolt (Barrel Type)300X10 Mm , Chromium Plated Brass Screws 30 Mm

BRR:7514669 Material Supply For , Stone Aggregate(Single Size): 40 Mm Nominal Size , Stone Aggregate(Single Size):20 Mm Nominal Size , Stone Aggregate(Single Size): 10 Mm Nominal Size , Stone Aggregate(Single Size): 6 Mm Nominal Size , Coarse Sand (Zone Iii) , Portland Cement , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With Hopper , Vibrator (Needle Type 40 Mm) , Stone For Masonry Work , Twisted Steel/Deformed Bars , Solid Blocks Of Size 30X20x15cm , Fine Sand (Zone Iv) , Water Thinnable Cement Primer For Interior Wall Surface, Having Voc Content Less Than 50 Gms/Litre , Acrylic Exterior Paint , Exterior Primer , Flats Up To 10 Mm In Thickness , Welding By Electric Plant , Red Oxide Zinc Chromate Primer , Structural Steel Such As Tees, Angles, Channels And R.S. Joists , Adjustable Telescopic Prop 3 M (2.02-3.75M) , Beam Clamp 300-380 Mm (450-1070 Mm) , Aracanut Post , Bamboo/Kallanmula , G.I Pipes 50 Mm Dia , G.I. Pipes 40 Mm Dia , Gi Trafford Profile Sheet 0.35Mm Thick , Stainless Steel Screws 50 Mm , Pvc Bend 63 Mm Dia , Pvc Tee 63X63x63 Mm Dia , Pvc End Cap 63 Mm Dia , Pvc Elbow 63 Mm Dia , Pvc Pipe 63 Mm Outer Dia. 4 Kgf/Cm2 , Pvc Reducer 63X50 Mm Dia , Pvc Vent Cowl 63 Mm Dia , Polyethylene Water Storage Tank With Cover And Suitable Locking Arrangemnet , Wall Form Panel 1250X500 Mm , 100 Mm Channel Shoulder 2.5 M Long , Double Clip (Bridge Clip) , Single Clip , M.S. Tube 40 Mm Dia , Laterate Stone Of Size 40X20x15cm , Solid Blocks Of Size 30X20x20cm , Galvanised Steel Corrugated Sheets , Galvanised Steel Bolts & Nuts 6 Mm Dia And 25 Mm Long Round Head With Slots , Galvanised Steel J Or L Hooks 8 Mm Dia , G.I Limpet Washer , Bitumen Washer , Roofing Paint For Iron Sheets In Red Colour , Galvanised Wire Mesh Of Average Width Of Aperture 1.4 And Nominal Dia. Of Wire 0.63 Mm , Wire Nails , Mild Steel Plates , Mild Steel Rivets , 20 Mm Dia Holding Down Bolts , Quarry Waste , Corner Angle 45X45x5 Mm 1.50 M Long , Bamboo 25 Mm Dia 2.5 Meter Long , Separation Membrane Of Impermeable Plastic Sheeting 125 Micron Thick , Boulder 50 Mm To 200 Mm , Crates Made Of Mesh Type 10X12 (D=100Mm) Zinc Coated (Mash Wire Diameter 3.00 Mm) , Green Net 75% Shade , Polyurethene Bags , Royalty For Good Earth , Interlocking C.C. Paver Block (80 Mm Thick, M-30) , Precast Chequered Cement Tiles 22 Mm Thick Dark Shade Using Ordinary Cement , Mild Steel Tubes Hot Finished Welded Type , 200 Mm Aluminium Aldrop , Second Class Kail Wood In Planks , Second Class Kail Wood In Scantling , Safeda Ballies 125 Mm Diameter , Mild Steel Round Bar 12 Mm Dia And Below , Pvc Pipe 15 Mm Outer Dia. 12Kgf/Cm2 , Ceramic Glazed Tiles Ist Quality Minimum Thickness 5 Mm In All Colours Shades And Designs Except Burgundy, Bottle Green Black , Ceramic Glazed Tiles Ist Quality 300 X 300 Mm In All Shades And Designs Of White, Ivory, Grey, Fume Red Brown Etc. , Vitreous China Orrisa Type W.C. Pan Size 580 Mm , Vitrified Floor Tile 60X60 Cm , Hollock Ballies 125 Mm Diameter , Adjustable Span Eso+Si (2.35-3.40) , Anjili Wood Scantls , Bright Finished Or Black Enameled Mild Steel Butt Hinges 100X58x1.90 Mm , Bright Finished Or Black Enameled Mild Steel Butt Hinges 50X37x1.50 Mm , Bright Finished Or Black Enameled Mild Steel Screws 40 Mm , Bright Finished Or Black Enameled Mild Steel Screws 20 Mm , Anjili Wood Planks , Float Glass Sheet Of Nominal Thickness 4 Mm (Weight Not Less Than 10 Kg/Sqm) , Factory Made Door Frame Size 50X47 Mm With Wall Thickness 5 Mm Made Of Single Piece Extruded Profile , 35 Mm Thick Factory Made Solid Panel Pvc Door Shutter Of Single Piece Extruded Profile Non Decorative Finished (Matt Finished) , Powder Coated M.S. Butt Hinges 100 Mm X58 Mm X 1.9 Mm , Anodised Aluminium Handles 125 Mm With Plate 175 X 32 Mm , Chromium Plated Brass Screws 25 Mm , Iron Hooks & Eyes 100 Mm , Anodised Aluminium Tower Bolt (Barrel Type)300X10 Mm , Chromium Plated Brass Screws 30 Mm

BRR:7514570 Tender For 330 Improvements To Muslyarpadi Jilli Company Road 330 Improvements To Muslyarpadi Jilli Company Road - Annual Plan-Annual Plan Kuttippuram GP Project 330 Improvements to Muslyarpadi Jilli Company Road-Improvements to Muslyarpadi Jilli Company Road-General Civil Work-Ward 23 Sl. No. Item Description 1 Road concrete 2 5.5.A.1a:Modified Penetration Macadam 50 mm thick using Bitumen S-65
Construction of penetration macadam over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506. 3 5.5.B.2a:Modified Penetration Macadam 75 mm thick using Bitumen S-65
Construction of penetration macadam over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506.
(B) 75 mm thick :- (II) Bitumen (S-65) 4 5.2.1a:Tack Coat
Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503. 5 5.11.1.A.2a:Mix Seal Surfacing - Manual Means - Type A - Bitumen S-65
Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type-B) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification Clause 509
By Manual Means :- Type A
(II) Bitumen (S-65) 6 improvements 7 OD343510/2023-2024:Filling with Quarry Muck Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade 8 OD343511/2023-2024: Modi Data of 75.8.1:Providing Plane cement concrete for road work CC1:2:4 (1 cement:2fine aggregate:4 course aggregate) laid to required slop and camber in panels (@3m c/c)as required including compaction, finishing,and tamping etc.max. size of course aggregate not exeeding 25mm ,mixed in concrete mixer etc complete as per specification (Excluding form work ) (i) Nominal mix 1:2:4 9 OD343509/2023-2024:Providing and fixing Granite of any colour and shade for Name board, of required size laid over base of cement mortar 1:4 (1 cement:4 Coarse sand) including all charges etc. complete at all, levels including lettering and fixing

BRR:7514465 Providing And Supplying Various Materials Providing And Supplying Various Materials At Changephal Tq Sidhkhed Raja Dist Buldana , Handicap Wheel Chire (For Handicap) , Handicap Walker , Fogging Machine , 20 W Led Light , 18 W Led Light , 24 W Light , Fingerprint Time & Attendance Device , Biometric Fingerprint Scanner Machine , Plastic Pedal Garbage Waste Dustbin 70 Ltr. , Stainless Steel Taki /Kothi/Leak Proof/Kitchen Storage/Atta /Grains 60 L Drum , Shoe Stand , Thor Netyanche Photo Frame All , Stainless Steel Round Handa, For Home , Hospital Bed , Computer Table , Window Curtains , Door Curtains , Wall Watch , Kids Seesaw Toy , Kids Pyramid Ring , Toy Drum , Puzzle , Kids Ball , Toy Horse , Toy Blocks , Skipping Rope , Chess Mat With Chess Coins , Sponge Rubber Ring , Carrom , Cub , Plastic Chatai Mat , Plastic Aasan Patti , Broom , Door Mat , Big Parat , Polpat Beln , Aarsa , Kangva , Steel Backet , Steel Jag , Steel Oil Cattle , Floor Cleaning Mop With Bucket , Steel Dabba , 36 W Led Street Light , 1 Meter Wire 1Mm , Holder (1 Nos) , Clamp And Pipe Set , Bleachingpowder(Tcl) 25 Kg Bag , Weighing Scale 100Kg And Above , Hight Chart , Infrentometer , Stadiometer With Weighing Scale , Weighing Scale For Baby , Aakar Khelni Sanch 0 Te 5Yr With Chart , Anganwadi Karita Kothi 100 Kg , Anganwadi Karita Kothi 50 Kg , Kapat 4X3 Size , Kapat 7X3 Size , Cooker 10Kg , Cooker 25Kg , Palte Pavbhaji , Water Glass Ss , Table 2X4 Size , Plastice Chair , Hand Wash Station 1 Besin , Hand Wash Station 4 Besin , Led Smart Tv 32 , Led Smart Tv 40 , Led Smart Tv 50 , Cricket Set (2 Bat , 6 Ball, 2 Pair Stamp, Hand Glos 3 Pair, Pad 3 Pair , Helmet 3 Pair) , Sound System Trolley Speaker With 2 Wireless Mic(12) , Foot Ball , Pen Drive 64 , Medical Kit (Oximter, Turmameter, Bandez, Iodine,Cipladim) , B P Aprates (Isi Mark) , Saniterypad (6 Nos Set) , Suger Test Kit (Isi Mark) , Bebi Powder (Jonsun Baby) , Bebi Powder (Himalay) , Machardani For 0 Te 1 Yr Baby , Tharmameter , Preganews Kit , Kadahi 10Kg , Bhagune 10Kg , Baket 10Ltr , Topile 5 Kg , Bhat Wadi , Vaghral , Kavcha , Mat 12X20 Size , Mat 6X10 Size , Computer Set (500Gb Hhd,4Gb Ram, I3 Processer With Keybord Mouse, Vga And Power Supply) 1 Year Warranty , Moniter 22 , Moniter 15 , Laptop (1Tb Hhd,4Gb Ram, I3 Processer) 1 Year Warranty , Small Tractor For Rent Per Day With Fawarni Yantra With Driver , Deltafog 1 Ltr , Deskbench Small Size 1 To 5 Year Childern , Babay Chire 40X32x30x20 Size , Slide 58X18x36x54 Size , Super Swing 30X33x43 , Book For Laburary (1 Set Samaj Sudharak Yanche 5 Book, Bharat History 1Book, Othe R4 Book ) 10 Book Set , Water Jar 18 Ltr , Plastic Tank 500 Lit , Balnket , Automatic Sanitary Napkinvending Mashine , 36 W Solar Light Inbuild Battary , 75 W Panel, Arm Bracket 6 M Gi Pole ( All Set ) , Minral Water Pot , Hikvision 16 Channel Dvr With 5 Mp ,6 Bullet &10 Drone Cameras With Audio Recording + 4Tb Hdd+ (3+1) Cable Roll+16 Ch Pawer Supply+ Usewell Bnc & Dc Full Combo Kit , Musical Harmonium , Tabla Set , Dholki , Bansuri , Damru , Walking Crutch , Walking Stick , Hearing Mashine , Trueview 3+3Mp 4G Mini Pt Solar Powered Linkage Security Camera, 1296P Advanced Cctv Surveillance Solution, Outdoor Camera, Water Proof, 2 Way Talk , Ceiling Fan , Wall Fan , Childer Dress 1 Yr , Childer Dress 2 Yr , Childer Dress 3 Yr , Childer Dress 4 Yr , All In Printer , Wheel Chare

BRR:7514377 Supply Of Laboratory Equipments For Life Sciences Depts. (Botany, Zoology And Biotechnology) , Name Of The Instrument (Refer Tender Document For Details) , Flame Photometer , Cooling Centrifuge Plus, Capacity 1200 Ml. Rpm - 20000 , Elisa Reader With Kit And Accessories , Autoclave , Horizontal Electrophoresis , Verticalelectrophoresis , Pcr Thermal Cycler , Ultra Centrifuge Cooling Machine , Uv - Vis Spectrophotometer , Microscope With Camera , Colorimeter , Compound Light Microscope , Hot Air Oven , Ph Meter , Turbidity Meter (0-1000Ntu) , Conductivity Meter , Weighing Balance , Centrifuge Machine , Digital Ultrasonicwater Bath(Sonicator) (20)

BRR:7514366 Tender For Addn/Altn To Qtr At Bhagat Road, Fafa Under Ge (W) Jalandhar Cantt; 1 Demolition of cement concrete in ground floor and paving n.exc 15 cm thick (below or above ground level complete all as spd and directed . 2 Demolition of brick or stone masonary built in cement mortar complete all as spd and directed. 3 Taking down cement plastering on stone wall/brick wall etc including racking out of joints hacking for key scrubbing down with water etc 4 M&L brick work with sub-class B bricks, straight or curved on plan exceeding 6 M mean radius built in CM 1:6 complete all as spd and directed 5 M&L brick work with sub class B bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as spd and directed. 6 M&LCement concrete type D 2, 1:4:8 (using 40 mm gradedstone aggregate) in sub base of flooring, hard standing,Manhole, drain etc. 7 M&L 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggr) as in plinth protection/path finishing the surface even and smooth without using extra cement complete all as spd and directed. Note : Plinth protection shall be laid in (1:20) slope. The concrete shall be laid at a stretch not exceeding 3metre in length. Joint gap between adjoining slab, at corners and at junctions ofwalls shallnot exceed 10mm in width and shall be sealed with mastic filling i.e. one part of bitumen 85/ 25 grade mixed with 3 part of sand. Top surface of concrete shall be finished even and smooth without using extra cement. Joints shall be provided at not more than 3 metre interval at corner and as junction of walls complete all as spd and directed. 8 M&L 10mm thick rendering in CM 1:3 onbrick/concrete surfaceas in ceiling and finishing the surface even and smooth with out using extra cement. complete all as spd and directed. 9 Removing old lime wash (if any), hacking for key, raking out joints of old brick work or stone work built in lime or mud mortar; not previously plastered;and scrubbing down with water etc. to receive plaster, walls are built in cement or cement lime mortar.complete all as spd and directed. 10 M&L 15mm thick rendering with water proofing liquid as per manufacturere instruction of approved make : Like : Sica/Dr Fixit/Fosroc on wall in CM 1:4 onbrick/concrete surfaceand finishing the surface even and smooth with out using extra cement complete all as spd and directed. 11 M&L 15mm thick rendering on wall in CM 1:6 onbrick/concrete surfaceand finishing the surface even and smooth with out using extra cement complete all as spd and directed. 12 Demolition of floor hearth or wall tiling including cement mortar bedding (not backing ) removing serviceable tiles to store and rubbish of the premises complete all as spd and directed. 13 M&L colouredGlazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface over 10 mm thick cement plaster in CM 1:4 complete all as spd and directed. 14 Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as spd and directed. 15 M & L for applying neat cement slurry with 3.0kg of cement per sq. metre complete all as spd and directed. 16 M & L Non skid Coloured ceramic tiles 7 to 8 mm thick (squre or rectangle) area of each tile exce 0.11 SqM but not exceeding 0.18 SqMinfloors etc, set and jointed in neat cement slurry and pinted in white or coloured cement to match with including 15mm thick screed bed in CM 1:6. complete all as spd and directed. 17 M&L Machine cut kota stone slab flooring 18 - 20mm thick over 20mm thick cement screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing upto mirror finished complete all as spd and directed. 18 M&L Machine cut kota stone slab flooring 18 - 20mm thick as in skiritng, riser of steps etc laid over 10mm thick cement plaster in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing upto mirror finished complete all as spd and directed. 19 Demolition of re-inforced cement concrete of any description and in anypositionnot otherwise specifically provided for complete all as spd and directed. 20 Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces of concrete complete all as spd and directed. 21 M & L for Reinforced cement concrete type B1 1:2:4 (20 mm graded aggregate) (nominal mix) inSlabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as spd and directed. 22 M&L mild steel TMT bars 8mm dia and over cut to length bent to shape required including cranking bending and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips confomring to GdI IS-432 complete all as spd and directed. 23 Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortercomplete all as spd and directed. 24 M&L 20mm Granite (of any type) work(table rubbed and polished) in steps, jambs , pillars, window cills, cooking platforms, and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm thick cement screed bed in CM 1:4 complete all as spd and directed. 25 Rounding/mouldingto edges of Kota stone slabs, marble stone, granite stone slabs one edge, such as in steps, cooking platform , and other similar situations etc complete all as spd and directed. 26 M&L for 15mm thickrenderingin1:3 CMwith water proofing liquid as per manufacturere instruction of approved make : Like : Sica/Dr Fixit/Fosroc as in sunken portion complete all as directed. 27 M&L for applying evenly a tack coat of industrial bituminous 85/25 @ 1.20 Kg per sqmincluding cleaning surfaces.complete all as directed. 28 M&L APP based polymeric membrance minimum weight not less than 3.0kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150gms/sqm) land on primed surface by forced application(complete area sealed by gas flame)with over lap of 15 cm complete all as specified and directed complete all as spd and directed. 29 M& L Cement concrete type E-2, 1:5:10 using 40mm graded brick aggregate in foundations filling and mass concrete as in sunken floorcomplete all as spd and directed. 30 Cutting holes into or through brick walls built, in cement mortar Superficial area N.exc 150 sq. cm upto 23cm of depth of wall, complete all as spd and directed. 31 M & L for 50mm dia GI pipe,med grade beveled cut at both ends by making hole in walls sunken portion aprox above the RCC slab and ceiling finished the hole with cement plaster 1:2 to match with existing surface complete etc.(Measured for cutting holes shall be paid in concerned sch item) complete all as spd and directed. 32 Taking down chowkats or frames with shutters (without taking of shutter from the frame)of any description alongwith fittings n.exc 1.5sqm eachcomplete all as spd and directed. 33 Taking down chowkats or frames with shutters (with out taking of shutter from the frame) of any description alongwith fittings exc 1.5sqm n.exc 4 sqm eachcomplete all as spd and directed. 34 Taking down shutters any description exc 1 sqm but n.exc 2sqm each and all as specifiedand directed . 35 Taking down shutters of any description not exc 1 Sqm and not exc 2 sqm each and refixing in same opening after necessary all repairingcomplete all as spd and directed. Note : Change of old wiremesh will be measured in connected supply only items. 36 S&F pressed steeldoor framewith one or more rebate including necessary fixing lugs, hinges, lock stricking plate of size 105 x60mm complete all as spd and directed. 37 S&F pressed steeldoor framewith one or more rebate including necessary fixing lugs, hinges, lock stricking plate of size 125 x60mm complete all as spd and directed. 38 M&L for PCC Type B0-1:2:4 using 12.5mm graded aggregate as in filling of pressed steel frame, hold fasts and similars articlescomplete all as spd and directed. 39 S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65x 100 mm, one or more rebates comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp- ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madecomplete all as spd and directed. 40 Providing and fixing factory made single extruded WPC(Wood Polymer Composite) solid decorative type flush door shutter of size30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistur proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. 41 Cutting holes in brick walls incement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required built in cement motar in brick wall depth of embedded portion of holdfast exc half brick but n exc one brickcomplete all as spd and directed. 42 S&F2nd class hardwood rail and style, factoy made plain,framed,panelled shutters (two panel) 35mm thick, with lock rails and panel of 9mm B. W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rails and stile as per IS : 1003 (Part-I), kiln seasoned and chamically pressure treatedcomplete all as spd and directed. 43 S&F 2nd class hardwood glazed and skelton door shutters 35 mm thick divided into squares open rebated and prepared to receive glass, gauge etc edges of framing plain, chamfered, rounded tfitted with mltred beads for securing glass etc, size of members as specified in SSR Pt 1 section 8 clause 8.20 (b) supplied and fitted to chowkats with plain, chamfered or rounded mited and rebated bars any numberscomplete all as spd and directed. 44 Dismantling of unframed timber scantlingsin fillets, rails, posts, rafters, purlins,etc. under 40 sq. cm in section in any positioncomplete all as spd and directed. 45 Dismantling boarding, any description, fixed in any position with nailsComplete all as spd and directed. 46 S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size Frame size 50 x 100 mm for wardrobe, one or more rebates comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp- ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madecomplete all as spd and directed. 47 S & F Factory Made Solid PVC Moulded Door Shutter With Core free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawingcomplete all as spd and directed. 48 Solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube 49 S&F factory made solid panel pvc door shutter 30mm thick (style) consisiting of frame made out ofM.S.Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement,fixing in the frame at the site as per specification & drawing. 50 M & L Powder coated aluminium (minimum thickness of powder coating 50 micron) for sliding window shutters including providing and fixing roller, three track system, locking arrangement fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws where necessary all complete as per architectural drawings and the directions of Engineer-in-charge. 51 S & F powder coated of any colour (Thickness or powder coating not less than 50 micron).aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21100mm long (2 no.) suitable handle (1 no.)complete all as spd and directed. 52 S&F framed work such as grills & gates, gratings with ends of bars shouldered on forged in spickes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, rallings, framework of water tanks and similar work conforming to Fe-290 Gde-E-165complete all as spd and directed. 53 S&F Galvanisedmild steel wire cloth, 0.56mm nominal dia of wire and avg erage with aperature 1.18 mm fixed with tinned tacks, or galvanised wire staplescomplete all as spd and directed. 54 M&L for 4.80mm thick sheet glass ordinary quality glazing with oil puttyin squares not exceeding 0.50 Sqm in each pane complete all as specified and directed. 55 Supply only Galvanisedmild steel wire cloth, 0.56mm nominal dia of wire and any width of aparture 1.18mm fixed with alu wire staples fixed to wood/steel framescomplete all as spd and directed. 56 S&F Butt hinges, medium weight cold rolled 100 mm size ISI markedcomplete all as spd and directed. 57 S&F aluminium anodised barrel tower bolts of extruded section 150mm longcomplete all as spd and directed. 58 S&F Extruded aluminium alloy handles fabricated type anodised 150mm sizecomplete all as spd and directed. 59 S&F aluminium alloy anodised sliding door bolts 250 mm long with hasp, staple (bolt type)and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections as specified. 60 S & F 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller platecomplete all as spd and directed. 61 S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 150 mmcomplete all as spd and directed. 62 S & F in repair for mild steel pipe 25 mm dia Harrison rails, mild steel, chromium plated with fixing brackets, stops,rollers etc as approved complete all as specified. 63 S&F in replacement 100 mm hasp and staple aluminium anodised including bolt to hinge plate and fixed with screw complete all as specified. 64 Providing and fixing solid PVC Kitchen Cabinet of size 1845 x 770 x 620mm at site made out of 18mm thick one side decorative lamination and other side balancing lamination sheet consisting of car case 18mm thick pvc sheet and provision of shutter made out of 18mm thick one side decorative lamionated PVC sheet all required brackets SS screw etc. the panel shall be febricated using adhessive and screws where ever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bend finish as per make and specification mentioned as per drawing and specification approved by Engr in Charge. 65 S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45x 70 mm for kitchen shelf, one or more rebates comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp- ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madecomplete all as spd and directed. 66 Providing and fixing factory made 18mm thick solid, decorative, WPC(Wood Polymer Composite) laminated board of required size as in shutter comprising of virgin polymer of K value 57-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives made from extrusion process WPC foam sheet single extruded (inner with having minimum density not less than650 kg/cum and screw withdrawal strength of 2000 N (Face) & 1100 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. 67 Material and labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc.including welding grinding,buffing,polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete including fixing the railing with necessary accessories and stainless steel dash fasteners,stainless steel bolts etc,of required size, on the top of floor or the side of waist slab with suitable arrangementcomplete all as spd and directed. 68 Taking up or down 15 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed. 69 Taking up or down 20 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed. 70 S&F 15mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed. 71 Refixing 15mm old GItubing and connections in new or old position (Walls, ceiling, floors, etc.)complete all as spd and directed. 72 S&F 20 mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed. 73 Refixing 20 mm old GI tubing and connections in new or old position (Walls, ceiling, floors, etc.)complete all as spd and directed. 74 Cutting chases, pinning in making good to facings where reqd and pointing in cement mortar1:3 to ends or edges of shelves , for water tubing etc andmaking good, cutting exc 10cm girth but not exc 20cm girth in stone wallscomplete all as spd and directed. 75 Dismantiling of water tanks of capacity exc 250 & n exc 500 ltrs incl all necessary fittingscomplete all as spd and directed. 76 S&F 500 ltrs PVC rotational moulded polyethylene water storage tanks double layer made (cylindrical vertical with closed top ) hoisted and fixed in position all as spd in SSR part-I complete all as spd and directed. 77 Disconnecting existing tanks, setting aside (or loweringif required)for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including cleaning of over head tank 500ltr capacity of any description and capacity, descaling, washing with detergent powder, removing vegetation around the over head tank/plat form complete all as specified and directed. 78 S&F 20mm Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair complete all as spd and directed. 79 S&F ball float valve brass with epoxy coated aluminimum rodfor 20 mm bore pipe high pressure with polythelene high density float and complete screwed for iron pipe in repair. complete all as spd and directed. 80 S&F in repair 15mm dia long body Bib taps cast copper alloywith fancy type chromium lated crutch or butterfly handle screwed down, scewed for iron pipes or for brass ferrule complete all as spd and directed. 81 S&F in repair 15mm brass CP bath mixer for mixing hot & cold water screwed down for iron pipe and fixedcomplete all as spd and directed. 82 S&F in repair 15mm brass CP WHB/Sink mixer swan neck for mixing hot & cold water screwed down for iron pipe and fixed.complete all as spd and directed. 83 S&F 15mm dia Brass stop valves chromium plated, fancy type with long shank and cup concealed type screwed down, highpressure with crutch or butterfly handle, screwed both ends for iron pipe or for unlori as specified and fixed in repairs. complete all as spd and directed. 84 S&F 15mm dia Brass stop valves chromium plated, fancy type with cup screwed down, highpressure with crutch or butterfly handle, screwed both ends for iron pipe or for unlons as specified and fixed in repairs. 85 S&F 600x450 bevelled edged looking mirror 2mm thick of selected quality glass, mounted on 4 mm thick PVC sheet and with aluminnium frame work fitted with chromium plated brass screws and cup washers including taking old one in repaircomplete all as spd and directed. 86 S&F in Vitreous china corner wash hand basin (385X385X150mm) white, angular back excluding taps,including brackets &32mm waste cuppling complete all as specifed and directed. 87 S&F Vitreous China wash down Water closet pan (pedestal pattern) with plastic water closet seatcover closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging divice (excluding flusing cistern and flush pipe) in repairscomplete all as spd and directed. 88 S&F Vitreous China Water closet (Squatting pattern) Orissa Pattern size 580x 440 mm white with P or S trap, front or back inlet and foots rests any pattern (excluding flusing cistern and flush pipe) in repairscomplete all as spd and directed. 89 S&F 10 Litre PVC valveless syphonic action flushing cistern low level white with inlet ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32 mm dis for low level cistern in repairscomplete all as spd and directed. 90 S&F 15mm PVC connection 450mm long with PTMT nuts of superior quality as specified in repair. complete all as spd and directed. 91 S&F in toilet paper holder of brass chromium platedfixed to walls with brass screws complete all as spd and directed. 92 Supply and fixed CP Soap dish, any type fixed to walls with plugs with chromium plated brass screwscomplete all as spd and directed. 93 Supply and fixing for glass Shelf with stainless steel railing and 8mm premium quality black glass shelf of size 450mm x 150mm complete all as specified and directed. 94 S&F for brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges etc complete all as spd and directed. 95 Supply and fixing for glass Corner Shelf with stainless steel railing and 8mm premium quality black glass shelf of size 12 dia complete all as specified and directed. 96 S&F Health faucet mild steel chromium plated suitable for 15mm dia pipe with 1.25mtr long flexible tube and ABS wall hook including making connection and fixed in position complete in all respect as specified. 97 M&L 75mm PVC (SWR) floor trap , plain with CP grating including jointing with solvent cement complete all as spd and directed. 98 S&F in replacement CP grating 100-125mm dia circularof approved make and fixing with cement mortar 1:3 on Nahani Trap or floor trap complete all as specified. 99 S&F in repair brass chromium plated shower rose 125mm size complete all as spd and directed. 100 Supply in fixing in repairs sink with drainage board made Stainless steel 1mm thickkitchen or laboratory with plugs, washer and wastes pipe , including bedding in cement mortar on dwraf wall orincluding fixing cantilever brackets and connecting union pipe, over all size 915mm x 460mm bowl size 410mm x330mm x160mm.complete all as spd and directed. 101 S & F in replacement stainless steel kitchen plate rack, made out of 1mm thick stainless steel size 30 x 24 x 10 (Miinimum weight 7 Kg) with shelves and plate position as approved complete all as specified and directed. 102 Dismantlingof brick tiles single layer as in roofcovering complete all as specified 103 Demolition of mud in roofs any thicknessincludingplastering and leeping(whether full thickness removed or only a part thereof)complete all as spd and directed. 104 Cleaning/Roughening surfaces of old concerete floor/roof by picking , sweeping clean and washing down with water to romove the dust etc complete all as spd. 105 (i) M&L for providing, cement concrete in roof kerbs or mud stops, rounded or chamfered on edges and PCC pedding with cement concrete type B-1, 1:2:4 (using 12.50mm graded stone aggregate) to top surface of slab in slop 1:40,with using water proofing liquid as per manufacturere instruction of approved make : Like : Sica/Dr Fixit/Fosroc,finishing the surface even and smooth without using extra cement complete all as specified. 106 (ii) M&L 15mm thick rendering with water proofing liquid as per manufacturere instruction of approved make : Like : Sica/Dr Fixit/Fosroc on wall in CM 1:4 onbrick/concrete surfaceand finishing the surface even and smooth with out using extra cement (iii) Providing and applying Epoxy primer (02 fast component resin of hardner) on the prepared surfacev @200gm per Sqm.(iv) Providing and applying Liquid Polyurea - PU based hybrid elestomeric water proofing membrane at existing/newly constructed roofs. Double coat is required on the smooth and cleared surface @ 1.50Kg per Sqm. (v) After coating of primer of two coats of ULTRON (US) a proper protective plaster/layer is to be done by laying Geo textile and 40mm screed on the top of final coating. (Make - Asian Paints, BASF & SIKA) Note:- Ser No (i) to (v) : The application shall be done by the authorised applicator of the manufacture with a letter of proof stating the authenticity of the applicator firm. 107 Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)complete all as spd and directed. 108 Dismantling of cast iron or reinforced concrete drain pipes of size 75-100mm dia, jointed in cement mortarandtakingout of trenches, if required.complete all as spd and directed. 109 S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints,fixed to wallscomplete all as spd and directed. 110 S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wallscomplete all as spd and directed. 111 S&F110mmPVC (SWR) bendscomplete all as spd and directed. 112 S&F75 mmPVC (SWR) bends complete all as spd and directed. 113 S & F for PVC 110mm (SWR) vent cowlcomplete all as spd and directed. 114 M&L for repairing of R.C.C projections, chajjias, roof slab, facia etc in patches not exceeding 3 Sqm in each patch by necessary preparation. Scarpping, cutting, chiseling derusting and cleaning exposed reinforcement, surfaces of damaged, loose R.,C.C surfaces and applying one coat of rust stop solution of approved make and filling the surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggreagates and reinforced with welded TMT bars/mesh (If Reqd) of weight exc 2 kg per sqm but n.exc 3kg/sqm with or without facia and finished with cement and sand motar (1:3) using coarse sand and thickness of R.C.C member n.exc 100mm including necessary form work and applyingtwo coats of finishes to match with the existing surfaces in at any height complete all as specified and directed by Engr-in-charge. (Note : Cost of form work and welded mesh shall be deemed to be included in unit rate quoted by the contractor complete all as specified and as directed. 115 Excavation in trenches not exc 1.5m wide and not exc 1.5m deep for foundation etcfor shafts, wells, cesspits , manholes pier holes, etc n exc 10 sqm on plan and n exc 1.5m in depth and getting out in soft/loose soilcomplete all as specified and directed. 116 Demolition and breaking up drain pipes 150mm bore (salt glazed ware, AC or Reinforced) set in cement mortar all as spd and directed 117 M &L for 150mm bore SGSW drain pipe (Grade-A) laid in trenches and jointed in CM 1:1 and tested complete all as spd and directed 118 M&L for concrete bed for 150mm in PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) to drain pipes including packing under,haunching against the sides of pipes after they are laid and testedcomplete all as specified and directed. 119 Cutting into existing manholes for connecting new drains making good to open and rendering, cutting out existing benching for and forming branch channel 1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1,smooth finished and reforming benchingcomplete all as spd and directed. 120 Demolition of re-inforced cement concrete of any description and in anypositionnot otherwise specifically provided forcomplete all as spd and directed. 121 M&L RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in precast RCC manhole / septic tanks ,drain,covers including all form work and setting in CM 1:4 all as specified and shown on drgs. 122 M&L mild steel TMT bars 8mm dia and over cut to length bent to shape required including cranking bending and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips confomring to GdI IS-432complete all as spd and directed. 123 Material and labour for cement concrete 1:2:4 Type B-1using 20 mm graded stone aggregate as in copings, weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed by the Engineer-in-Charge. 124 M & L for applying two coat of synthetic enamelled paint over one coat of pink primer including preparation of new wood surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge 125 M & L for applying one coat of synthetic enamelled paintincluding preparation of old treated wood surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge 126 M & L for applying two coat of synthetic enamelled paintover one coat of red oxide primer including preparation of new steel surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge 127 M & L for applying one coat of synthetic enamelled paintincluding preparation of old decoratedsteel surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge 128 M & L for applying white wash of 3 coats on ceiling incl preparation newly plastered surfaces as specified and directed. 129 Complete removal of existing treatment andapplying Two coat of white wash on ceiling incl preparation old plastered surfaces as specified and directed. 130 M & L for applying white wash of 3 coats on wallsincl preparation newly plastered surfaces as specified and directed. 131 Complete removal of existing treatment on wall andapplying Two coat of white wash incl preparation old plastered surfaces as specified and directed. 132 Material and labour for preparation of new plastered surfaces on walls and applying two coats of oil distemper over one coat of chalk whitening complete all as specified. 133 Complete removal of existing treatment on wall andapplying Two coat of Oil distemper (white or tinted) on old plastred surfaces incl preparatory to distempering on walls etc (Surface finished even and smooth) complete all as specified and as directed by Engineer-in-Charge. 134 Material and labour for preparation of new plastered surfaces on walls and applying two coats of cement base paintover one coat of cement primer complete all as specified. 135 Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out soft/ lose soilcomplete all as spd and directed. 136 Excavation in post holes each nexc 0.50 cum , getting out, returning filling in and ramming earth or broken rubble mixed with earth in layers not exceeding 25cm in soft/loose soilcomplete all as spd and directed. 137 M & L for PCC (1:2:4) typeB-2 (using 40mm graded crushed stone aggregates ) lean concrete as in foundation, filling and mass concrete of post complete all as specified . 138 M&L Broken stone or boulders as in hardcore of gauge n.exc 63mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered, rammed to a true surface etc complete all as specified and directed 139 M/L 100mm thick cement concrete 1:4:8, type D-2 using 40mm graded stone aggregatecomplete all as spd and directed. 140 M & L for 25mm thick Sand coushening under paver block complete all as specified and directed. 141 M&L machine pressed precast coloured concrete coloured interlocking paver blocksany shape and size confirming of IS 15658: 2006 of 60mm thick , M-35 laid and jointed with grey cement and pigment.complete all as spd and directed. 142 M & L for Plain Cement Concrete Type B1 1:2:4 (using 20 mm gradedstone aggregate) cast in situ inkerbs or mud stops, rounded or chamfered on edges of paving blocks as directed including use and waste of form work.complete all as spd and directed. 143 S&F Steel work as in tubular section for Post, Purline etc including special shaped washer , angle cleat, holdfast, gussete plate etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240cut or notched forming holes, without any attachment including drilling, fitting, riveting and or welding or connecting with bolts and nuts (incl rivet or nut and bolts) providing and fitting angle cleats Gussete plates etc also for welding plumbing, truing up and fixing complete as directed by Engr-in-Charge. 144 M&L pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with J or L type or cranked hookbolts complete as directed by Engr-in-charge. 145 M & L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with J or L type or cranked hookbolts complete as directed by Engr-in-charge. 146 M & L for Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters,nosingtosteps includingembedinginconcrete and screwing etc. wind ties for roofincluding securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling,boltingor riveting, etc., and similar work conforming to Fe-290 Gde E-165complete all as spd and directed. 147 M&L for prepration of new steel surface of any description, over 10cm in width or girth,not otherwise described and apply two coat of synthetic enamelpaint over a coat of red oxide primer etc complete all as specified and directed. 148 M & L for prepration of new steel surface of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint and apply two coat of synthetic enamelpaint over a coat of red oxide primer etc. complete all as spd and directed. 149 Returning, filling in , including spreading, levelling , watering and well ramming in layers not exc 25 cm thick by using hard/dense soil as in low line area as directed by Engr-In-Charge . 150 Removing excavated soils n.exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point.complete all as spd and directed. 151 Taking down carefully aluminium / copper point wiring (light / fan / socket or power) complete including fitting such as switches, ceiling roses, socket, light fittings, regulators etc complete and making good disturbed surfaces of walls, floors 152 Taking down unserviceable Submain/Cableof any size as directed by Engineer-In-Charge. 153 Taking down main switch / DB as directed by Engineer-In-Charge. 154 M & L for sub main wiring with two single core PVC insulated and unsheathed cable 6 sqmm with multi stranded copper conductor , FRLS type cable drawn throughand including PVC concealed conduit of not less than 25mm in size complete with all accessories alongwith provn of 6 sqmm PVC insulated and unsheathed ,multi stranded copper conductor , FRLS type cable as earth wire.(Three runs of cable and one run of conduit shall be measured as one length) 155 M & L for concealed point wiring complete with 1.5 sqmm single core multistranded copper conductor FRLS, PVC insulated and unsheathed cable 650 /1100 volts grade drawn through & including PVC conduit ,medium grade with accessories like bends, tees, junction boxes etc fix on wall or ceiling surfaces all as specified including 1.5 sqmm , FRLS type , copper multistrandedcable as earth wire including sunken type pressed steel terminal boxes of thickness 1.6 mm thick and plastic laminated white / coloured top sheet cover 3.0 mm thick for: complete all as spd and directed. 156 One light / fan/bell pointcontrolled by one, one way switch. complete all as spd and directed. 157 One 3 pin socket out let 5 Amps on same board with other switches.complete all as spd and directed. 158 One 3 pin socket out let 5 Amps on the independent board.complete all as spd and directed. 159 Dittoall as per item No.5 about but with 2.5 sqmm multistranded copper multistranded conductor FRLS cable with 2.5 sqmm earth wire for one 6 pin socket outlet 15 amps on independent boardcomplete all as spd and directed. 160 S & F switch Piano 5 Amps, flush button type, SP, one way, 230 Volts, ACcomplete all as spd and directed. 161 S & F switch Piano 1 5 Amps, flush button type, SP, one way, 230 Volts, ACcomplete all as spd and directed. 162 S & Fsocket out let multipurpose 5 pin 5 Amps,230 Voltscomplete all as spd and directed. 163 S & Fsocket combination ,6 pin ,15 amps, flush type, multipurpose, 230 Vcomplete all as spd and directed. 164 Supply and fix bell push flash piano type 5 amps.complete all as spd and directed. 165 Supply and fix bell ding dong 230 Volts AC single pole.complete all as spd and directed. 166 M & L ceiling rose surface bakelite 65 x 50 mm three terminals complete all as specified. 167 Supply and fix DB,double door,SPN 8 way for MCB, 240 volt with 200 amps rated bus bar.complete all as spd and directed. 168 S & F MCB SPN40 to 63 Amps 240 voltscomplete all as spd and directed. 169 S & F MCB SP 6-32 Amps 240 voltscomplete all as spd and directed. 170 Supply and Fixingstepped socket type electronic fan regulator and connecting up complete all as directed by Engineer-In-Charge. 171 M & L Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings.complete all as spd and directed. 172 S&F in replacement LED tube light fitting 20Wbox type including LED lamp 20 W with 2200 lumen output with internal surge protection device of 4KV with voltage band of 140-280V CRI-6500K (White light) fixturesand connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.75mm 3 core complete all as specified and directed. 173 Supply & fixing in replacement LED street light fitting 35W including LED lamp pressure die cast aluminum IP66 with surge protection device of 10KV, IK7 LED6500K and connecting electrical to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.75mm 3 core complete all as specified and directed including bracket and fixing clamps etc.complete all as spd and directed. 174 Supply and fix LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holderconnecting up with three core flexible copper conductor cable of suitable size all as specified and directed. 175 Taking down existing Ceiling fan/Exhaust fancapacity/type carefully and refixing the same with gutties, nuts boltss if required complete all as specified and directed. 176 Taking down existing Geyser any capacity/type carefully and refixing the same with replacement of PVC connection/Steel connection and anchor fastenerpipe if required complete all as specified and directed. 177 Supply and laying GI Tube Med grade 50mm dia all as specified and directed. 178 Supply and fix MCCB 63 Amps 4 pole415 Volt,16 KA breaking capacity . complete all as spd and directed. 179 M&L for earthing complete with GI steel earth plate electrod 60x60cmx6.00mm thick bouried directly in ground /earth pit not less than 2.25m deep below the ground level with top edge of the plate not less than 1.5 m below the normal ground level connected to test point by using GI wire of dia 4 mm as earthing lead soldering/revated to earth plate at one end and connected DBby means of nut, bolts etc complete with PCC pit (1:3:6) type GI cover with handle funnel with watering pipe wire mess GI protection pipe for earthing lead all complete as specified and as per electric plate No.5 of SSR Part Icomplete all as spd and directed. 180 M& L for XPLE UG Cable of size 35 Sqmm 4 Core all as specified and directed. 181 M & L river sand in trenches as cable cushioning 8 cm below the cables and 15cm above the cable which is to be punned down to 10m all as specified and directed.only punned thickness will be measured.complete all as spd and directed. 182 Supply and lay burnt bricks sub class B standard size laid across the cable in trenches as protection to the cable all as specified and directed.

BRR:7513544 Bids Are Invited For Electronic Baby Weighing Scale - Rbsk Total Quantity : 7747

BRR:7513415 Bids Are Invited For Electronic Baby Weighing Scale - Rbsk (Q3) Total Quantity : 7

BRR:7513286 Bids Are Invited For Microsemi-Microanalytical Weighing Balance (Q2) Mse Total Quantity : 1

BRR:7513225 Bids Are Invited For Equipments At Pattikalan Lpg Bp 1 21 250 Kg Load Cell Flintec Atex Peso , Clamping Roller , Dp Valve , Dp Valve Diaphragm Seal , Flp Led Light For Vision Reader , Foot Buffer , Table Buffer , Side Buffer , Lpg Gun Kosel , Lpg Gun Mouth Bottom Part , Old Gun , Old Nozzle , Ss Base Plate , Vision Reader Stopper, Htpc , Digital Input Module , Digital Output Module , Strainer Filter , Self-Centring Spring , Checker Plate For Check Scale Platform , Check Scale Stopper , Filling Gun Guide Rod , Carousel Input Output Ss Plate , Electronic Weighing Scales Total Quantity : 984

BRR:7512735 Bids Are Invited For Gym Equipments Pec Dec Fly Machine , Leg Curt Leg Extension , Lat Pull Down With Rowing Ev , Smith Machine With Power Rack , Functional Trainer , Hyper Extension , Hack Squat , Preacher Curl Bench , Dumbbell Rack , Olympic Flat Bench , Olympic Incline Bench , Olympic Decline Bench , Simple Flat Bench , Utility Stool , Adjustable Bench , Plate Rack Tree , Commercial Trade Mill , Spin Bike , Cross Trainer , Aerobic Stepper , Swiss Ball , Medicine Ball 5 Kg , Olympic Rod Lock , Eva Mat 25 Mm 1 X 1 Mtr , Rubber Mat 20X20 Inch 10 Mm , Bouncer Dumbbell , Triangle Weight Plates , Olympic Rod , Cross Fit Ropes , Tire Big , Standing Punching Bag For Kick Boxing , Hammer , Weighing Scale , Dumbbell 12Kg 15 Kg 20K Gone Pair Each , Looking Mirror 6Ft X 4Ft , Foam Rollers , Bold Fit Gym Belt For Men And Women Lever Dead Lift For Workout , Yoga Wheel , Ankle And Wrist Weights Pair , Weightlifting Straps Pair , Wrist Support Band Pair , Handgrip Strengthner , Roller , Stretch Bands With And Without Handle Different Weights 2 Set Each , Gym Gloves With Wrist Support L Sizes , Utility Stool With Back Support , Abs Machine , Seated Hip Abductor Machine , Bold Fit Knee Caps , Abdominal Abs Roller , Seated Rowing Machine With Chest Support , Ez Bar With Spring Lock 3 Feet , Standing Calf Raises Machine , Skipping Ropes Thick Pro Training , Cable Attachment Set , Dips Bar Machine , Flat Gym Bench (V2) Total Quantity : 840

BRR:7511379 Tender For Development Work In Village Pali, Greater Noida., 1 BOQ 2 Excavation in foundation in ordinary soil(Loam, clay or sand) including lift upto 1.50 M. and lead upto 30 M. and including filling watering and ramming ofexcavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the Engineer-in-charge upto a distance of 30 M. from the foundation trenches. (Where machine con not reach/move). For Building work only(SOR-251a) 3 Cement concrete with 4cm gauge approved stone ballast, coarse sand & cement in the proportion of 8:4:1 including supply of all materials, labour, tools & plants etc. required for proper completion of the work. (UPPWD/SOR-2020/281) 4 Construction embankment approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2 MORTH-305. 5 Relaying of dismantled dry brick on edge flooring in required pattern with bricks of class desination 150 on a bed of 12mm mud mortar including filling joints with jamuna sand (By using old brick) (labour rate only)AR/GNIDA 6 apporach road shamshan ghat 7 Dry brick on edge flooring in required pattern with bricks of class designation 150 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.DSR-18/11.2 8 Cement concrete with 4cm gauge approved stone ballast, coarse sand & cement in the proportion of 8:4:1 including supply of all materials, labour, tools & plants etc. required for proper completion of the work. (UPPWD/SOR-2020/281) 9 Providing and laying I shaped interlocking tiles Rubber Moulded 80mm thick precast cement concrete having plan dimension 200 x (160+120mm) with compressive strength not be less than 40Mpa (M-40 and weight 5Kg, laid in required pattern over and including average 50mm thick compacted bed fine sand and filling the joints with fine sand all complete as per direction of Engineer-in-Charge with conforming to ISI-15658-2006 (SOR/A.R) Grey colour. 10 M-150 brick work in 1:6 one cement and four coarse sand 1.25 F.M. mortar in foundation and plinth including supply of all material, labour, T&P etc. required for proper completion of the workPWD Specification no 6.1.1 11 12mm cement plaster of mix: 1:4 (1 cement : 4 coarse sand) (DSR-2018/13.4.1/AR) 12 Cement concrete with 2cm gauge approved stone ballast, coarse sand & cement in the proportion of 4:2:1 including supply of all materials, labour, tools & plants etc. required for proper completion of the work. (UPPWD/SOR-2020/279(a)) 13 Plain Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications. RCC Grade M25 using batching plant transit mixer & manual placing . MORTH-9.06 D/Case-II 14 Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications. RCC Grade M25 using batching plant transit mixer & manual placing . MORTH-9.06 E/Case-II 15 Provide and fixing in position 12mm thickbitumen impregnated fibre board conformingato IS: 1838 including cost of primer,sealingcompound in expansion joints. 16 Excavation in foundation in ordinary soil (Loam, clay or sand) including lift upto 1.50m and lead upto 30M and including filling watering and ramming of excavated earth into trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by Engineer-in-charge upto a distance of 30M from the foundation trenches. SOR-2020/251(a)) 17 Providing, laying, jointing and testing of PVCpipe (finolex make ring fit) of following dia 6kg. per Sqcm including all specialised fittingetc. as required for complection of work (Thecontractor has to arrange the source of waterand require head for testing)90 mm AR/GNIDA 18 Providing and fixing G.I. union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work). 19 15 mm nominal bore (DSR-18/18.46.1/ AR) 20 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc 21 15 mm dia nominal bore. (DSR-18/18.12.1/ AR) 22 Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main: 23 15 mm nominal bore (DSR-18/18.20.1/SOR) 24 Excavation in foundation in ordinary soil(Loam, clay or sand) including lift upto 1.50 M. and lead upto 30 M. and including filling watering and ramming ofexcavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the Engineer-in-charge upto a distance of 30 M. from the foundation trenches. (Where machine con not reach/move). For Building work only(SOR-251a) 25 Supply of ISI marked RCC S&S NP-2 pipes of following size including carting, loading, unloading at godown including all taxes and levies & rubber rings. (AR/GNIDA)250 mm dia NP-2 pipe 26 Laying of NP-2 RCC S&S pipes jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 coarse sand) including testing of joints etc. complete. (AR/GNIDA)250 mm dia NP-2 pipe 27 Providing and laying in position cement concrete 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) in concrete cradle under NP-2 pipe of following diameter including centring shuttering but excluding excavation as per approved (AR/GNIDA) 28 250mm dia NP-2 PipeAR/GNIDA 29 Constructing brick masonary circular typemanhole 0.91m internal dia at bottom anda0.56m dia at top with 100 class designation FPSbricks in cement mortar 1:4 (1 cement: 4 coarsesand) inside and outside above ground levelcement plaster 12mm thick with cement mortar1:3 (1 cement: 3 coarse sand) finished with alfloating coat of neat cement, foundationconcrete 1:4:8 (1 cement: 4 coarse sand: 8graded stone aggregate 40mm nominal size) andamaking necessary channel in cement concrete1:2:4 (1 cement: 2 coarse sand: 4 graded stoneaggregate 20mm nominal size) finished with alfloating coat of neat cement all complete as perastandard design. 30 0.91m deep with SFRC cover and frame (heavyduty HD-20 grade designation) 560mm internaldia meter conforming to IS 12592. Total weightof cover and frame not less than 182 Kg. fixedain cement concrete 1:2:4 (1 cement: 2 coarsesand: 4 graded stone aggregate 20 mm nominalasize) including centring shuttering, Supply andfixing Poly propelene foot rest & excludingexcavation all complete. SORDSR-18/19.9.1.1 31 Extra depth of 0.91dia manhole 1.67m deepwith SFRC cover and frame(heavy duty HD-20grade desination) 560mm internal dia meterconformingIS 12592. Total weight of cover and frame not less than 182kg.Fixed in cementconcrete 1:2:4(1Cement: 2coarse sandgraded stone)DSR-18/19.10.1.1 32 Providing orange colour safety foot rest ofminimum 6 mm thick plastic encapsulated asper IS: 10910 on 12mm dia steel barconforming to IS: 1786 having minimum crosssection as 23 mmx25mm and over all minimumlength 263 mm and width as 165mm withminimum 112 mm space between protruded legshaving 2 mm tread on top surface by ribbing orchequering besides necessary and adequateanchoring projections on tail length on 138 mmaas per standard drawing and suitable to withastand the bend test and chemical resistance testas per specifications and having manufactureshpermanent identification mark to be visible evendafter fixing, including fixing in manholes with30x20x15 cm cement concrete block 1:3:6 (1cement3 coarse sand: 6 graded stoneaggregate 20 mm nominal size) complete as perdesign. DSR-18/AR 33 Excavation in foundation in ordinary soil(Loam, clay or sand) including lift upto 1.50 M. and lead upto 30 M. and including filling watering and ramming ofexcavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the Engineer-in-charge upto a distance of 30 M. from the foundation trenches 34 SEWER CONNECTION 35 Supply of ISI marked RCC S&S NP-2 pipes of following size including carting, loading, unloading at godown including all taxes and levies & rubber rings. (AR/GNIDA)150 mm dia NP-2 pipe 36 Laying of NP-2 RCC S&S pipes jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 coarse sand) including testing of joints etc. complete. (AR/GNIDA)150 mm dia NP-2 pipe 37 Providing and laying in position cement concrete 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) in concrete cradle under NP-2 pipe of following diameter including centring shuttering but excluding excavation. (AR/GNIDA)150mm dia NP-2 concrete cradle 38 Constructing masonry chamber 60x60x75 cm. inside, in bricks work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size), i/c necessary excavation,foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard designWith F.P.S bricks 39 P/L S.W. intercepting trap in manholes withastiff mixture of cement mortar 1: 1. (1cement: 1 fine sand)150mm diaDSR-18/19.34.2 40 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 41 Thermo-mechanically treated bars (Sail Steel) (DSR-18/5.22A.3 42 Providing and fixing in cement mortar 1:6 (1cement: 6 fine sand) red sand stone 30mmathick over drain DSR-18/3.9 43 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. (Sail Steel) 44 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar worksDSR-18/10.25.2 45 Labour Cess will be paid extra as per applicable 46 GST will be paid extra as per applicable

BRR:7511363 Tender For For Agricultural Marketing Facilities In The Sugar Mill Area Reconstruction Work Of Mukari Road To Dutt Nagar Road In District Baghpat In Financial Year 2024-25 - Water Bound Macadam Grading - 3 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100kNin stages to proper grade and camber, applying and brooming, stone screening to fill-up to interstices of coarse aggregate, watering and compacting to the required density Grading III as per Techincal Specification Clause 405 3BIncluding supply of all Material, Labour, T&P etc labour cess, royalty and all other applicable Taxes required for proper completion of work as directed by Engineer in charge but excluding GST. 2 Providing and applying primer coat with bitumen emulsion SS-1 on prepared surface of granular Base including cleaning of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means. Including supply of all Material, Labour, T&P etc also including VAT, labour cess, royalty and all other applicable Taxes required for proper completion of work as per direction of Engineer-in-charge. Technical Specificaton Clasue (502-I).Including supply of all Material, Labour, T&P etc labour cess, royalty and all other applicable Taxes required for proper completion of work as directed by Engineer in charge but excluding GST. 3 Providing and applying tack coat with bitumen VG-10 grade usingpressure distributor at the rate of 0.25 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom. Including supply of all Material Labour, T&P etc also including labour cess, royalty and all other applicable Taxes(But excluding GST) required for proper completion of work as per direction of Engineer-in-charge. Technical Specificaton Clasue(SI.NO. 503).Including supply of all Material, Labour, T&P etc labour cess, royalty and all other applicable Taxes required for proper completion of work as directed by Engineer in charge but excluding GST. 4 Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates using VG-10 Bitumen required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling witha three wheele80-100kn static roller capacity,finished to required level and gradesto be followed by Type-C seal coat. Including supply of all MaterialLabour, T&P etc also includinglabour cess, royalty and all other applicable Taxes(But excluding GST) required for proper completion of work as per direction of Engineer-in-charge.as per Technical Specification Clause. 508.Including supply of all Material Labour, T&P etc also including labour cess, royalty and all other applicable Taxes(But excluding GST) required for proper completion of work as per direction of Engineer-in-charge. Technical Specificaton Clasue(SI.NO. 503).Including supply of all Material, Labour, T&P etc labour cess, royalty and all other applicable Taxes required for proper completion of work as directed by Engineer in charge but excluding GST. 5 Providing and laying Type-C seal coat with VG-10 bitumen sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type C. Including supply of all Material Labour, T&P etc also including labour cess, royalty and all other applicable Taxes (But excluding GST) required for proper completion of work as per direction of Engineer-in-charge.as per technical specification clause 510.Including supply of all Material, Labour, T&P etc labour cess, royalty and all other applicable Taxes required for proper completion of work as directed by Engineer in charge but excluding GST. 6 Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 Including supply of all Material, Labour, T&P etc labour cess, royalty and all other applicable Taxes required for proper completion of work as directed by Engineer in charge but excluding GST. 7 Brick lining on both side of the road of M-150 bricks 7 cm. wide. 11 cm. deep, laid with mud mortar including labour & supply of bricks finished to the required template and in proper alignment and also including dressing and ramming the excavated earth as directed by the Engineer-in-charge. SOR No. 765.Including supply of all Material, Labour, T&P etc labour cess, royalty and all other applicable Taxes required for proper completion of work as directed by Engineer in charge but excluding GST. 8 Construction ofun-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design,laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days using curing compound (where specified) and water finishing to lines and grade as per drawingand Technical Specification Clause 1501. Including supply of all Material, Labour, T&P etc labour cess, royalty and all other applicable Taxes required for proper completion of work as directed by Engineer in charge but excluding GST.

BRR:7511200 Tender for Mgnrrgs Materials Supply Supply Of Materials For Works Under Mgnregs For A Period Of 6 Months (Part 1). , Laying And Jointing Pvc Pipe. Heading , Supplyingstone Aggregate(Single Size): 40 Mm Nominal Size , Supplying And Stacking Stone Aggregate(Single Size):20 Mm Nominal Size , Supplyingstone Aggregate(Single Size):10 Mm Nominal Size , Supplying And Stacking Manufacturedsand(Coarse Sand Zone Iii) , Portland Cement53 Grade , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With Hopper , Vibrator (Needle Type 40 Mm) , Quarry Waste

BRR:7511109 Tender For Annual Plan-Keezhallur Gp-254/24-25-Maintenance Works To Various Anganavadi-General Civil Work - 15.9.1:Demolishing stone rubble masonry manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in- Charges:In Lime Mortar 3 2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil 4 4.1.6:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) 5 4.1.4:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 )1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) 6 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more 7 5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. 8 5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform 9 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) 10 OD393214/2024-2025:Laterate masonry with neatly dressed laterate stone of size 35x20x20 cm or nearest size in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc. (Modified 50.6.7.1) 11 OD393124/2024-2025:Laterate masonry with neatly dressed laterate stone of size 35x20x20cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc. 12 OD393201/2024-2025:Laterate dry masonry with departmental laterate stone of size 35x20x20cm or nearest size for foundation and basement including all cost of materials, labour charges etc. DSR 2016 13 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) 14 5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size 15 13.43.1:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer 16 13.60.1:Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work 17 OD393126/2024-2025:Providing and laying 60 mm thick or nearest available size factory made cement concrete interlocking paver block made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of stone aggregate 6mm nominal size, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. 18 14.43:Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 19 14.53.1:Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:One or more coats on old work 20 17.10.1.3:Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink with drain board510x1040 mm bowl depth 200 mm 21 17.7.2:Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630 x 450 mm with a single 15 mm C.P. brass pillar tap 22 10.25.2:Item Shifted to Sub head 14 as item 14.73Item Shifted to head 14 as item 14.74Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 23 14.54.1:Painting with synthetic enamel paint of approved brand and manufacture of required colour to an give even shade:One or more coats on old work 24 13.48.3:Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture 25 50.18.7.4.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 10Kgf/cm2- Internal work - Exposed on wall 26 50.18.7.3.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 25 mm dia 10Kgf/ cm2- Internal work- Exposed on wall 27 50.9.1.1:Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Anjili wood /jack wood 28 50.9.2.1:Providing and fixing paneled and glazed shutters for doors, windows and clerestory windows, 35 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineerin - charge using Anjili/ Jack wood 29 50.14.1.1:Removing and refixing door shutters after necessary repairs for easy opening and closing etc complete as per the direction of site Engineer-in-charge. 30 14.5.1:Renewing glass panes, with putty and nails wherever necessary including racking out the old putty :Float glass panes of thickness 4 mm 31 18.15.2:Providing and fixing brass bib cock of approved quality :20 mm nominal bore 32 11.41.2:Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm. 33 11.46.2:Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, ofapproved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm 34 50.18.9.7.2:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.63 mm dia 4 Kgf/cm2 35 OD393123/2024-2025:Supplying and fixing PVC door hollow frame including cost and conveyance of material, labour charges etc. complete. 36 OD393122/2024-2025:Supplying and fixing PVC door shutter including cost and conveyance of material, labour charges etc. complete. 37 50.14.1.2:Removing and refixing window shutters after necessary repairs for easy opening and closing etc complete as per the direction of site Engineer-in-charge 38 13.48.2:Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufacture 39 50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete 40 OD393127/2024-2025:Providing and fixing 150mm UPVC square gutter pipe over G.I.clamp profile @1 m. C/C 41 50.12.5.1:Providing and fixing false ceiling with e board classic tile or equivalent make of size 610x610x4 mm ceiling of approved quality in aluminium frame work with necessary screws etc complete ( aluminium frame work shall be paid separately) 42 15.13.2:Taking out doors, windows and clerestory window shutters (steel or wood ) including stacking within 50 metres lead:Of area beyond 3 sq. metres 43 50.18.9.20.4:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Bend 44 5.21:Extra for providing and fixing expanded metal mesh of size 20x60 mm and strands 3.25 mm wide 1.6 mm thick weighing 3.64 kg per sqm for encasing or rolled steel sections in beams, columns and grillages excluding cost of hangers. 45 21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron) 46 21.1.2.2:For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron) 47 21.3.1:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

BRR:7510756 Tender For Addn/Altn To Building No T-77 At 24 Ed Af Station Manauri; 1 Excavating soft/loose soil in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan andexc 1.5 m in depth and getting out complete all as specified and directed by Engineer -In-Charge. 2 Returning, filling of soft/loose soil in, including spreading, levelling,watering and well ramming in layers not exc 25 cm.complete all as specified and directed by Engineer -In-Charge. 3 Removing excavated material (soils) exc. 250 m but nexc. 500 m and depositing where directed complete all as specified. 4 Removing excavated material (soils)n exc. 50 m and depositing where directed complete all as specified. 5 Removing excavated material (soils) exc. 50 m but n exc. 250m and depositing where directed complete all as specified. 6 M&L for Cement concrete type C2 (1:3:6 ) using 40 mm grade stone gradedaggregate in foundations, filling and mass concrete complete all as specified and directed. 7 Demolition of brickwork built in cement mortar including all quoins, archers, pillars,etc excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed. 8 M&L for brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in in cement mortar (1:6) complete all as specified. 9 M&L for rendering 10mm thick in cement mortar (1:6) on fair faces of brick work or concrete finished fair even surfaces.complete all as specified and directed. 10 M&L for rendering 15 mm thick in cement mortar (1:4) with mixed water proofing compound (liquid) other than fairfaces of brick or concrete surface finished even and smooth without using extra cement as complete all as specified & directed.Note:- Water proofing compound (liquid) seprately shall be measured paid saprately. 11 Supply only liquid water proofing compound @ 200 ml per bag of cement as complete all as specified. 12 Dismantling of Stone slabs in roofs, floors, chajjas, landings, etc., any thickness, jointed in any mortar complete all as specified and directed by Engg-in -charge. 13 Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15cm thickness complete all as specified and directed by Eng-in-Charge.. 14 M & L for brushing neat cement slurry with 3.0kg of cement per sq. metrecomplete all as specified and directed by Eng-in-Charge.. 15 M & L for 75mm thick Cement concrete type C-1, 1:3:6 (20mm graded stone aggregate) in Plinth Protection etc. complete all as specified and directed by Eng-in-Charge. 16 M&L for hardcore of broken stone or boulders gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and directed. 17 M&L for Cement concrete type D2 (1:4:8 ) using 40 mmgraded stone aggregate in foundations, filling and mass concrete complete all as specified and directed. 18 M&L for 50mm ThickCement concrete type A-1, (1:1.5:3)(20mm graded stone aggregate) finished even and fair complete all as specified and directed. 19 M&L for Granolithic concrete 1:1:2 floor topping 30mm thick laid over cement concrete sub floors etc. and finishedto an even and fair surface complete all as specified and directed. 20 M&L for 30 mm thick wearproof topping of metallic floor (40kg of cement ,10 kg hardener and 0.034cum of granite chips for per sqm area of floor)as specified (incorporating an approved metallic floor hardner), laid on concrete floors and pavings, and finished even and smoothcomplete all as specified and directed.Note:- Metalic hardner shall be measured and paid separately as supply only. 21 M & L for Treating cement concrete or granolithic concrete surfaces with three dressings of sodium silicate solution complete all as specified and directed by Engineer-In-Charge. 22 Supply only metallic floor hardener complete all as specified and directed. 23 M&L for forming 12 mm thick expansion joint filled with preformed bituminous filler and top 30mm primed and sealed with sealing compound grade A for 110 mm thick concrete floor complete all as specified and directed. 24 M &L for cement concrete using 20mm grade stone aggregateas , in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, type B1 (1:2:4) including necessary form work complete all as specified and directed. 25 M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in rcc band and rcc precast slab complete all as specified. 26 All as per item No 25 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified. 27 M&L for PCC 1:2:4 Type B1 using 20 mm graded stone aggregate as in coping/holdfastcomplete all as specified and directed. 28 Use and waste formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc.for rough finished surface of concrete also splays between floors and beams, etc.complete all as specified and directed. 29 M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over & including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed. 30 S&F for mild steel framed work such as grills , gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. 31 S&F for anodised sliding Aluminium door shutter including anodised Aluminium frame aluminium section weighing 0.55 kg /per meterand including necessary joining cleats , glazing cleats , rubber Neoprene packing handles , anodized Al. snaps beading , screws including 5.00 mm thick glass panes, floor door spring necessary tower bolt, lock with locking arrangement complete all as specified and directed. 32 S & F powder coated anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engineer in charge. 33 S&F powder coated anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m includingnecessary joining cleats, glazing clips, rubber packing, anodised aluminiumsnap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified and directed . 34 S&F aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staplescomplete all as specified and directed . 35 S&F sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane of 5.5 mm thick complete all as specified and directed . . 36 S&F aluminium composite panel overall 3mm thick panel, aluminium sheet thickness 0.5mm minimum width 1.22 metre, minimum length 2.44 metre weight 4.5 Kg/Sqm external faces coil coated with PVDF and internal face coil coated polyster for cladding wall, column, beams and ceiling etc fixed with and including to frame work as per manufacturers instructionscomplete as specified and directed. Note : Colour of ACP shall be approved by AGE(I). 37 Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings valley guttercomplete all as specified and directed 38 Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings and ridgescomplete all as specified and directed 39 Dismantling structural steel work including doors, gates but excluding framed truss etc.complete all as specified and directed 40 S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing of Fe 410 -W (GdeE- 250) quality A complete all as specified and directed 41 Dismantling expanded metal, weight not exceeding 4.0 kg/Sqm any thickness or mesh, fixed with steel or wood fillets, if any complete all as specified & directed. 42 S&F for expanded metal, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members complete all as specified and directed . 43 S&F Pre-painted galvalume sheet aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in ridge or similar work fixed with self tapping screws complete all asspecified and directed. 44 S & F 12 mm thick gypsum plaster board flame proof conforming to IS-2095 1982 to fix as suspended celling with on step and including frame consisting perimeter powder coated GI sheet channelI 20X27X30.5 mm intermediate channel 45 (WEB) X 1. 5 ( flange ) X 0.9 mm @ 1.22 M C/C with ceiling angle 2 5 X10X0.5 MM fixed to soffit with GI cleat and steel expansion fastner , celing section 51.5 ( Knurled web X 26 ( flange) with lips of 10.5 mm X 0.5mm @ 610 mm C/C nec clip , screw , nylon sleeves etc complete and apply two coats of oil bound distemper over a coat of putty on celling over preparation surface complete all as specified and directed. 45 Demolition and breaking up drain pipes of 150 mm dia (Salt glazed ware, AC ,PVC orreinforced concrete) set in cement mortar complete all as specified and directed . 46 S & F 150mm PVC (SWR) pipes single socketed in any length laid in trenches or in floor & walls with MS clamps etc complete all as specified and directed 47 S & FPVC (SWR) bends any radius 150mm dia complete all as specified and directed. 48 M & L for preparation of old steel surface exceeding 10 cm width or girth and apply two coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. 49 M&L for applying two coats of syntheticenamel over a coat of redoxide primer and prepartion of on new steel or iron surfaces of any description, over 10cm in width or girth not otherwise described complete all as specified. 50 Taking down steel window frame with shutters (without taking off shutters from the frames) not exc. 150 sqm complete all as specified and directed.. 51 M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces incl. preparation of new surfaces.as percomplete all as specified and directed.. 52 M & L for mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. compete all as specified and directed by E-in-Charge. (Fe- 410W Grade-E-250 quality A). 53 M&L fro distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturers Specification. Two or more coats on new workincl. preparation of new surfaces.as percomplete all as specified and directed.. 54 M& L for 3 mm thick wall care putty on plaster surfacecomplete all as specified and directed. 55 M&L for 60 mm thick PUF roof sheet manufactured in computerised plant and come with pre-painted Galvalume steel sheet and the density of Poly urethane foam sandwiched between two fascias ( thickness of top fasciasGalvalume steel sheet is 0.5 mmand thickness of bottom fasciasGalvalume steel sheet is 0.4 mm) is 40 + 2 kg/cum and featured with weather proof , flame retardation with self extinguishing property , environment friendly , resistant to corrosion , termites and fungus. includingfixing with suitable screws etc. and as per manufacturers instructioncomplete all as specified and directed... 56 M&L for 100 mm thick PUF wall panel manufactured in computerised plant and come with pre-painted Galvalume steel sheet having 320 MPa for Gr80 and the density of Poly urethane foam sandwiched between two fascias of Galvalume steel sheet0.5 mm thick is 40 + 2 kg/cum, and featured with weather proof , flame retardation with self extinguishing property , environment friendly , resistant to corrosion , termites and fungus. including with fixing with u channel with dash fastener of size (M6 x 65 mm) ,L-angle (50x50x0.6/1.2mm),100 mm with plain strip,pop rivet and self drilling screw of size 12-14 x 140mm etc. and as per manufacturers instructioncomplete all as specified and directed. 57 Providing precast cement concrete type B-1 (1:2:4) using 20 mm graded stone aggregate set in 1:4 cement mortar in but in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces,complete all as specified and directed.. 58 M&L for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface areacomplete all as specified and directed.. 59 M&L for treating the backfill in contact with foundation at the rate of 7.5 litres ofemulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified & as directed. 60 M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified & as directed. 61 M&L for Treating the soil under plinth protection earth at therate of 5 litres of emulsion per square metre of surfacecomplete all as specified and directed.. 62 M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall, cmplete all as specified and directed.. 63 M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate,asin surface channels and drains filling & mass concrete etc complete all as specified and directed. 64 M&L for brick work with sub class B bricks(old size bricks) straight or curved on plan exceeding 6 mtr mean radius built in cement mortar 1 : 4 and external face of brick work pointed flush in the same mortar as the work proceeds, complete as specified and directed. 65 M&L for PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands,plinth courses, string courses, acing courses, parapets and railings upto 60 cm in height, copings,benching, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating,including necessary form workcomplete all as specified and directed.. 66 M&L for rendering 15 mm thick in cement mortar 1:4 with WPC/water proofing liquid on fair faces of brick or concretesurfaces finished even and fair complete all as specified and as directed.Note WPC/liquid shall be measured & paid seprately. Complete all as specified and directed.. 67 M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement,including forms, moulds, mi- tred/stopped ends etc.complete all as specified & as directed 68 Add or deduct for each 25 mm girth or part thereof over or under 30cm inner girth in cement concrete, using ex tra cement,including forms, moulds, mi- tred/stopped ends etc.complete all as specified & as directed. 69 450mm dia and 6.0m long Hume pipe culvert-01 Nos 70 Excavating soft/loose soil in trenches, n exc 1.5 m wide andexc 1.5 m in depth but not exc. 3 mtr depthfor foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc.nexc 10 sq m on planand getting out complete all as specified & as directed.. 71 M&L for RCC Hume pipe 450mm bore class NP-2 laid and jointed complete with collars including for laying pipes level or to falls in trenches, etc. on concrete bed or directly on hard ground as indicated and making joints and testing as specified. 72 M&L for preparing new surface and applying two coats of cement based paint over a coat of primer complete all as specified & as directed. 73 Surface excavation in soft / loose soil n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting outcomplete as specified and directed. 74 Removing excavated (soil) material exc. 50 m andupto a total distance of 250 m. of soil,complete as specified and directed. 75 M&L for 75 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate,including necessary formwork and finishing the surface of concrete,even & rough to receive the topping layer complete all as specified and directed. 76 M&L for 150 mm thick cement concrete work in pavement/ hard-standing of flexural strength 40 kg/per square centimetre in field using400 kg of cement per cubic metre, including necessary use & wasteof formwork for laying pavement concrete/ hardstanding in bays between joints & contraction ,expansion joints or between the two contraction jointscomplete all as specified and directed. 77 M & L for finishing surface of concrete roads , by brooming, complete all as specified and directed. 78 M & L for forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ of thickness of concrete slab in 150 mm,complete all as specified and directed. 79 Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade A ,complete all as specified and directed. 80 M & L for Earthing complete with galvanised steel earth electrode plate of size 600x600x6.0 mm thick, buried directly in ground(earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.50m below normal ground level, connected to galvanised iron strip of size 32 x 6 mm as earth lead up to test point with suitable GI nuts/bolts and brazed properly up to main board including earth pit in cement concrete 1:2:4 type B-1 using 20mm graded stone aggregates,40mm thick precast RCC cover in 1:2:4 reinforced with expanded metal(weight not less than 4 kg/sqm), and frame of angle iron 25x25x6mm with lugs 02 nos with 6mm dia MS bar handle made to shape, excavation and earth work in any type of soil and including light grade GI watering pipe 20mm bore with funnel and strip mesh and light grade GI earth wire protection pipe 40mm bore up to main board complete as shown in electrical plate no 3 of MES schedule Part-I , connected to earthing testing point and testing on completion complete including taking down of old existing one all as specified anddirected by Engr-in-charge.Note: (i) The unit rate includes GI pipe up to 7.5m for protection of earth lead andany additional lengthshall be measured separately .(ii) The unit rate includesmain earthing lead/strip from earth electrode to test point up to 7.5 meter and any additon length shall be measured and paid separately (iii) In case measured value of earth resistance is recorded more than 1.0 ohms then the earthing shall be re done by the contractor without any extra cost to the department. 81 M & L for Air termination single pointed aluminium rod 12 mm dia and 300 mm long completeincluding taking down old unsv all as specified and directed by Engr-in- Charge. 82 M &L for test point terminal block made of gun metal or phosphorus bronze 75x75x25mm , drilled and screwed including 3 nos , 8mm dia, 25mm long hex head screw complete including taking down old unsv complete all as specified and directed 83 M&L for aluminium strip 25 x3.15mm with saddles and fixing screws etc for roof conductors and down conductors above ground for lightening conductor complete with provision for fixing on epoxy insulatorsincluding taking down old unsv complete all as specified and directed. 84 Supply & Fixing ofGI pipe, light grade 15 mm dia bore for installation of air termination rod including all fixing arrangements to walls and ceiling or laidcomplete all as specified and directed 85 Supply and fixing of Galvanised iron strip 32 x 6mm buried in groundor fixed to poles or any other indicated situation for loop earthing as ring main conductor complete including taking down old unsv acomplete all as specified and directed 86 Material and labour for precast cement concrete(1:2:4) type B-1 using 20mm graded stone aggregate for support block of GI pipes and air termination rod complete all as specified and directed. 87 S & F GI pipe light grade 50 mm dia as protection to cable along the pole / across road crossing/through culvert/passing through ceiling/walls with necessary clamps-02 nos(Flat iron 50x6mm) with ,nuts and bolts for fixing on pole complete all as specified and as directed. 88 Supply and Fix epoxy insulator duly colouredwith necessary fixing arrangement on wall and roof for fixing of down conductor complete all as specified and directed 89 M&L for mild steel Cross arms bracings, support, clamps and back plates fabricated from structural steel section including nuts, bolts, washers etc, welding, bending cold or hot, drilling holes for bolts in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of aluminum paint complete all as specified and directed. 90 S & F plug type bib taps, cast iron, screwed for iron pipe and fixed for 15mm dia pipe complete including taking down old unsv complete all as specified and directed 91 Labour only for cutting to plinth protection/hard standing/road etc in 30 cm depth and 45 cm width to ensure laying/crossing of GI strip 32x6mm and repair to existing damaged/disturbed surface if any completeall as specified and directed by Engr-in- Charge. Note: The quoted rate shall include the cost of required material for repair to existing disturbed surface 92 Supply,installation,testing and commissioning of5-in-1 coolingsplit Air Conditioner of capacity 1.5 TR (smart cooling with energy saving) ,complete with HD Filter with Anti Virus Protection,Anti Allergy Filter, duly fitted DUAL Inverter Compressor with Varied Speed Dual Rotary Motor ,ADC Sensor ,Ocean Black Protection applied on Copper tubes of both Indoor & Outdoor unit , Refrigerant 410A/R32,4-way airswing operation,over load prtection,ISO – 9001 OEM Certification, suitable for operation on 220-240 volts single phase 50Hz Ac supply, comprising of following accessories with technical specification as under: 93 (a) Cooling Capacity Range (W) : 1100 to 7000 94 (b ) Power Input Heating/ Cooling : 1300W / 1270W 95 (c) ISEER Value : 3.2(Minimum) 96 (d )Star Rating :5 Star(Minimum) 97 (e) Noise Level (Indoor):Not more than 32db 98 (f) Air flow (Heating/Cooling) : 572 CFM /526 CFM 99 (g) Heating & Cooling Function Operation :-10°C to 54°C 100 (h) Air Throw : 16.0m (minimum) 101 (j) Type of condenser / evaporator : 100% Copper coil. (Aluminium coil / alloy shall not be accepted) 102 (l) Refrigerantcopper piping Minimum 0.8 mm wall thickness forsuction and discharge connections the indoor and outdoor units of suitable sizes complete with Nitrile Rubber insulation sleeves with preclad Aluminium & joints rapped with Aluminium tapesafter making of flares and joining with suitable size of flare nuts and saddling to the walls symmetrically as per common engineering practice. 103 (m) Providing of electric connection between outdoor and indoor units with suitable size of electric cables provided by the manufacturer along with the units 104 (n) Machine Control : With Battery Operated Remote Controller having LED / LCDdisplay complete with suitable size and capacity of batteries(cells). 105 (o) Features :AC shall be provided with atleast with certain features such as Sleep mode, turbo, swing, LCD / LED remote, lock, timer and temperature display. 106 (p) Drilling of suitable size of hole into wall alongwith 50mm PVC conduit (length equal to depth of hole) for passing of copper tubing (suction and discharge).Provisionand connecting wires flexible drain pipe of suitable dia of length as directed by Engr-in-Charge. 107 Note:(i)Connecting copper pipe (Minimum 6m length) ,Mounting bracket for indoor unit and Good quality PVC drain pipe of 25 mm dia included in the cost of item. 108 Supply and fix outdoor unit mounting brackets Factory made heavy duty floor anchored madeout of MS sheet bent to shape duly slotted for adjustment, powder coated GI/ aluminium stand for fixing Outdoor Condensing Units on the roof (or on the wall as required) of the room with serratedcomplete with s/sdash/hole fasteners of adequate length for fixing the bracket to wall for mounting of OutDoor unit complete all as specified and directed (Set of Two) 109 Supply and installation ofwater cooler Electric driven (single phase),having approx storage Capacity of 80 litres and nominal cooling capacity of 40 Litres per hour, with 02nos faucets,food grade stainless steel body and stainless steel tank,Refrigerant R134a,over load protection,suitable for 230V AC, 50Hz with stabilizer free operation.complete all as specified and directed by Engr-In-Charge. 110 M & L for AC point wiring using PVC insulated and unsheathed fire retardant low smoke and halogen(FR-LSH) copper with 4.0 sqmm PVC insulated and unsheathed fire retardant low smoke and halogen(FR-LSH) copper conductor single core multi stranded coppercable confirming to IS:694(2010) using approved colour code for phase and neutralas per IS code drawn through ERW metallicrigid steel stove enamelled black medium dutyconduit ( Concealed) ISI Marked screwed and socket end ,corrosion resisitant, medium protection gradehaving wall thickness not less than 2.0 mm thick and minimum 25 mm external dia but shall be increased as per actual site requirement in accordance with clause No 19.125 of SSR Part I ( ISI marked)including conduit accessories like bends, tees, junction boxes etc fixed concealedwith all accessories including PVC insulated and unsheathed FRLSH 4.0 sqmm multi stranded copper conductor cable (green color) as continous earthlead wire connected to common earth and earth dollycomplete all as specified and directed by Engr-in-Charge. 111 Supply and fix sheet metal enclosure with socket plug top and MCBs single pole and neutral, enclosure with a two pin and earth plug andsocket complete with one single pole MCBof capacity20 Amps 240 volts (for Acs) 112 Supply, installation, testing and commissioning of LT panel outdoor type confirming of IS 8623 Part (one), CPRI approval, totally enclosed vermin proof suitably ventilated for 3 phase, 4 wire 415 Volts, 50Hz, AC supply, outer sheel shall be made out of 3.15mm thick CRCA sheet & MS angle section of suitable size for frame, factory fabricated, compartmentalized inner shell shall be made of out of 2.0 mm thick CRCA sheet for control gear. Front and back door operating with locking arrangement at front. Protection of enclosure IP 56 as per IS-2147 of 1962 with pre-treatment trhough 7 tank hot chemical process prior to powder coated with minimum 50-70 micron of approved colour. The bottom of outer shell contains a detachable plate having provision for entry of armoured cable of adequate size. Computer cut self adhesive vinyl danger notice plate having conventional symbol of bones and skull to be provided. EPDM gasket of appropriate shape and size provided at all joints, door and covers including suitable size angle iron/flat iron frame work/support required with four legs 60cm long using angle iron 40x40x6mm, air passing holes and locking arrangement at front with duplicate keys and making connection of incoming and outgoing cable using proper cable lugs, 4 x legs 40 cm grouted in PCC 1:2:4 and making good distrubed surface complete and comprising of the following:- 113 (A).INCOMER 114 (i) MCCB 350 Amp 4 pole, 36 KA, lcs =100% lcu,confirming to IS:13947(Part-3) 1993 andIS/IEC:60947(Part-2) with adjutsable magnetic and adjustable thermal release, adjustable overload 65% to100% and adjustable short circuit release from 3.5 to10 ln setting complete with phase seperator - 01 Nos 115 (ii) 1 No., 230V, AC operated integral type Digital multi function meter with RS-485 port for measuring Amps ,Voltage, Energy, kWH, kVAH, frequency,Maximum Demand & power factor etc with TOD facility conforming to specifications, latest IEC/ EMC and EMI standards/criterion, with necessary Circuit MCBs and suitable size summating CTs forincomer metering supporting SCADA/BMS connectivity. 116 (iii)1- set Red/Green ON/OFF indicating lamps (iv)1- set of three phase (red, yellow, blue) indicating lamps (v) Amber healthy trip indicating lamps(vi)3 nos. cast resin current transformers of suitable ratio withVA Burden &protection and Class 1.0 for measurement or CTs of suitable capacity as per panel designer. 117 (B).BUSBAR 118 (i) TPN + EAluminium electrolytic grade high conductivity bus bar of rating not less than the 1.5 times the rated capacity of incomer MCCB/ACBshall be insulated with colour coded heat shrinkable sleeves and mountedon suitable size F class insulators made of non hygroscopic , non combustable, track resistant, high strength FRP/MC/DMC material at an interval not more than 500mm through out the length of busbar along with extension and interconnected busbar.The extension link shall not be less than 300mm long supported on suitable size F class insulatorsfor termination of incoming and outgoing cables.All control wires shall be with 2.5sqmm FRLS multi strandedcopper conductor and shall be properly bunched , tied,ferruled for proper identification and crimped with adequate size of lugs. 119 (C). OUTGOING 120 (i) MCCB 125 Amp 4 pole, 25 KA, lcs =100% lcu,confirming to IS:13947(Part-3) 1993 andIS/IEC:60947(Part-2) with fixed magnetic and adjustable thermal release, adjustable overload 70-100% and fixed short ckt release suitable for 10 ln setting complete with phase seperator - 01 nos 121 (ii) MCCB 63 Amp 4 pole, 25 KA, lcs =100% lcu,confirming to IS:13947(Part-3) 1993 andIS/IEC:60947(Part-2) with fixed magnetic and adjustable thermal release, adjustable overload 70-100% and fixed short ckt release suitable for 10 ln setting complete with phase seperator - 02 nos 122 (iii) MCB SPN C series 16Amp/32Amp ,10KA -04 Nos (v) MCB TPN C series 32 Amp,10KA - 02 Nos (vi) Auto/Manual selector swicth -01 nos (vii) 1 sets (2 no.) of AC operated, 3.5 Digit, independent Digital Ammeter,Digital Volt meter with necessary Circuit MCBs and with suitable size CTs connections as required foreach outgoing feeders. 123 (D). PLATFORM 124 Platform for feeder pillar/LT Panel shall be of suitable size as directed,450mm height above ground level, the foundation shall be using PCC 1:2:4 type B1,15cm thick, brick (sub class B) work in CM 1:6, redering 1:6 on exposed surfaces and 100mm thick PCC 1:3:6 type C1 using 20mm graded stone aggregate as in padding on top and grouting legs of panel. 125 Supply,laying,jointing and testing, fixing to wall using clamps/pole/floor or in air or passing through pipes/ducts/road/path/drain, laid in trenches, 1100 volts grade heavy duty electric cableXLPE insulated,screened ,PVC bedded, galvanised steel wire or wire armoured with electric power cable 1100 volts grade with stranded aluminium conductor of size 3.5 core 70 sqmmconfirming to IS - 7098 Part-1 and its latest amendments complete all as specified and as directed by Engr-in-Charge. 126 Supply,laying,jointing and testing, fixing to wall using clamps/pole/floor or in air or passing through pipes/ducts/road/path/drain, laid in trenches, 1100 volts grade heavy duty electric cableXLPE insulated,screened ,PVC bedded, galvanised steel wire or wire armoured with electric power cable 1100 volts grade with stranded aluminium conductor of size 3.5 core 35 sqmmconfirming to IS - 7098 Part-1 and its latest amendments complete all as specified and as directed by Engr-in-Charge. 127 S & F GI pipe light grade 80 mm dia as protection to cable along the pole / across road crossing/through culvert/passing through ceiling/walls with necessary clamps-02 nos(Flat iron 50x6mm) with ,nuts and bolts for fixing on pole complete all as specified and as directed. 128 S & F GI pipe light grade 40 mm dia as protection to cable along the pole / across road crossing/through culvert/passing through ceiling/walls with necessary clamps-02 nos(Flat iron 50x6mm) with ,nuts and bolts for fixing on pole complete all as specified and as directed.( For cable protection and GI earth lead) 129 Supply and fix CI cable route indicator 150mm dia , 5mm thick duly engraved with LT 1100 volts and bolted/welded to MS angle iron of size 40x 40x5 mm,70 cm long,50cm above ground level and 20 cm below ground, painted with 2 coats of synthetic enamel paint using approved colour over a coat of red oxide primer. The route indicator should begrouted in PCC using (1:2:4) type B-1 of size 150x100mm below the ground level completeall as specified and as directed by Engr-in-charge Note:- Route markers are to be fixed at a distance from each other all as directed. 130 Material and labour for boring of holes under road, pavement, runway, taxi track, hard standing by trenchless technolgy using ultrasound technique and necessary machine including HDPE pipe of 150 mm nominal dia PE 80 grade 0.4 Mpa working pressure for cable protection complete all as directed. Note: HDPE pipe shall be laid min 90 cm below the surface. complete all as specified and as directed. 131 M&L for sand cushioning to underground cable with dry sand locally available 8cm thick before laying of the cable and 15cm thick after laying and strectching the cable below the bricks/PCC cover, punning of sand using suitable T&P as per site condition, complete all as specified and as directed by Engr-in-Charge. Note : Punned thickness of sand to be consider for measurement purpose. 132 Supply and laying un-reinforced pre cast concrete cable coverconfirming to IS:5820 with minimum average breaking load capacity 200 kgs for unreinforced covers , class LV Type 1, flat, size 250mm x 150mm x 40mm complete all as specified and directed by Engr-in-Charge. 133 M&L for earth continuity conductor or main earthing lead/strip fixed to wall or buried in ground or drawn in conduit (pipe/fixed to poles) of any type or any other situation for loop earthing etc with GI Strip of size 32 x 6mm complete all as specified and as directed by Engr-in-charge. 134 Taking outLT cable any size from trenches/duct , stacking at site , checking by megger and shifting to other site for relaying complete all as specified and directed by Engr-in-Charge. 135 M & Lfor disconnectingincoming and out going cable connection of LT panel /Feeder Pillar Box of any sizeand taking out old unsv LT Panel and removal from sitecomplete all as specified and directed. 136 Taking down carefully (copper/aluminum) unsv point wiring complete of any type (batten/surface conduit or concealed) for light point, fan point, bell point ,socket point or power point includingfixture and fitting such as switches , ceiling roses, pendants , regulators , sockets , light fitting etc. removing material to store for keeping in safe custody or for taking credit( credit for above items should be made asper conditions seperately) and making good the disturbed surfaces of wall/floor or ceiling to match with existing surfaceand finishing the surfaces with distemper/white washing/colour washing as per existingcomplete all as specified and directed. 137 Taking down carefully by unscrewing from main switch boards/cut out boxes/MCB DBs / complete sealing the cable end and making good disturbed surface by walls etc. 138 Taking down carefully by unscrewing from fitting and fixtures such as ceiling fittings,bulk head fittings, tube light fittings , street light , flood light/welglass/ high bayLED lights etc all as specified and directed. 139 M & L for Point wiring for one light point/fan point on wall on ceiling/roof/trusses with necessary fixing arrangementscontrolled by one single pole one way switch using 1.5 sqmm PVC insulated and unsheathed fire retardant low smoke and halogen(FR-LSH) copper conductor single core multi stranded coppercable confirming to IS:694(2010) using approved colour code for phase and neutralas per IS code drawn through ERW metallicrigid steel stove enamelled black medium dutyconduit (Concealed) ISI Marked screwed and socket end ,corrosion resisitant, medium protection gradehaving wall thickness not less than 1.6 mm thickand minimum 20 mm external dia but shall be increased depending on No. of wires to be drawn as per actual site requirement in accordance with clause No 19.125 of SSR Part I including steel conduit accessories( ISI marked) like accessories like coupler lock,pipe hooks, nuts,girder clips or clamps bends, tees, junction boxes etcincluding PVC insulated and unsheathed FRLSH 1.5 sqmm multi stranded copper conductor cable (green color)as continous earthlead wire connected to common earth and earth dollycomplete all as specified and directed by Engr-in-Charge. 140 M & L for Point wiring for one power point on wallon ceiling/roof/trusses with necessary fixing arrangementscontrolled by one single pole one way switch using 2.5 sqmm PVC insulated and unsheathed fire retardant low smoke and halogen(FR-LSH) copper conductor single core multi stranded coppercable confirming to IS:694(2010) using approved colour code for phase and neutralas per IS code drawn through ERW metallicrigid steel stove enamelled black medium dutyconduit ( Concealed) ISI Marked screwed and socket end ,corrosion resisitant, medium protection gradehaving wall thickness not less than 1.6 mm thickand minimum 20 mm external dia but shall be increased depending on No. of wires to be drawn as per actual site requirement in accordance with clause No 19.125 of SSR Part I ( ISI marked)including steel conduit accessories like bends, tees, junction boxes etc including PVC insulated and unsheathed FRLSH 2.5 sqmm multi stranded copper conductor cable (green color)as continous earthlead wire connected to common earth and earth dollycomplete all as specified and directed by Engr-in-Charge. 141 Note for item no.139 & 140 (a) Item cost includes cost of FRLSH copper cable,rigid stove enamelled conduit including accessories and cutting of wall for fixing of modular flush boxes.(b) Cutting chases for concealed wiring shall be measured and paid seperately.(c ) ERW steel conduit shall emboss the Standard Mark (ISI) and its licence number on the black pipes conforming to IS 1239 (Part-1) 142 M & L cutting chases, pinning in,making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps cills, sun shadows, sheves lintels etc and cutting chases for concealed water tubing or concealed wiring etc and making good cutting n . exc 10 cm girth complete all as specified and as directed. 143 M & L cutting chases, pinning in,making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps cills, sun shadows, sheves lintels etc and cutting chases for concealed water tubing or concealed wiring etc and making good cutting exc 10 cm girth but not exc 20 cm girth complete all a specified and as directed. 144 S & F flame proof switch rotary type direct entry single pole 16A 250V flame proof-Exd suitable for 240V AC, 50Hz supply,in aluminium die cast alloy in LM6 construction,IP 65 protection,confirming to IS-2148:2004 /IEC 60079-1 (2007) complete all as specified and as directed. 145 Supply and fixing Flame proof Ex d ,weather proof interlocked switch socket & plug combined, 16A, 250V, 2P+earth , in cast aluminium alloy LM6 construction suitable for 240V AC, 50Hz supply,,confirming to IS 2148:2004(IEC-60079-1/2007) complete all as specified and as directed 146 Supply and fixing LEDhigh bay luminaire light fitting80 Wattflame proof-Exd suitable for 240V AC, 50Hz supply, IP 65 protection with Grey Epoxy Powder Coated Pressure Die Cast LM6 Aluminium Alloy Housing with heat resistant toughened glass,Impact Resistance - IK08,LED driver (with built in voltage surge protection, short Circuit, & Over Voltage protections), holders, connector etc. including cradle to hang the fitting complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and as directed 147 Supply & fixing of Flameproof Exd, weather proof MCB Distribution Box , TPN 4 way, 430V,50Hz,IP 66 weather proof protection with Grey Epoxy Powder Coated Pressure Die Cast LM6 Aluminium Alloy Housing ,suitable for flush mounting or surface mounting, including dissmantling existing one with its accessories, cutting chases to wall for fixing DB and making good the disturbed wall surface complete all as required at site and as directed comprising of following items as under :- 148 (a) Incomer - MCCB 4 Pole 63 A with Electronic Protection Unit Ics=100% Icu, Adjustable overload protection .4 to 1 x In, Protection against Short curcuit1.5 to 10 Ir, inbuilt instatneous protection,complete all as directed and specified Qty - 01 Nos 149 (b) Outgoing(i) MCB single pole 240 volts 10 Amps, C Curve, with rupturing capacity 10 KA ISI markedBiconnect lower terminals, IP 20 protected terminals, sliding shutters Qty -12 Nos (ii) MCB Tripple pole 415 volts 25 Amps, C Curve, with rupturing capacity 10 KA ISI marked Biconnect lower terminals, IP 20 protected terminals, sliding shuttersQty -01 Nos 150 S & F flame proof MCB DB SPN 8way with MCB 2P 32Amp -01 Nos (incomer) and MCB SP 10Amp -06 Nos(Outgoing) external protection metal clad suitable box with locking arrangements confirming to IP-66 with all necessary wiring connections and making good the distrubed surfaces to match with the existing complete all asspecifiedanddirectedby the Engineer-in-Charge 151 S & F flame proof / weather proof wall mountedair circulator fan 450mm sweep,0.25HP,1440RPM operating voltage range of 150V to 265Vwith a reputed driver, in aluminium die cast alloy LM6 construction of Gas Gr-IIA, IIB certified by CIMFR Dhanbad & CCOE (Pers) Nagpur, ISI marked including taking down old unsv fan and deposited to MES store yard complete all as directed. 152 Supply, install,commissioning and testing of commercial Air curtain unit of size 46 x 78 for prevention of dust and conditioned air losses, single phase, 220 V, 50HZ, made out of MS/CRCA sheet of minimum thickness 18 gauge finished with two coats of red oxide primer and final coat of synthetic enamel paint (oven baked) with MS - CRC 18 gauge square perforated suction grills, Aluminium alloy fans and singlephase electric motor, nozzles etc, complete with fittings and accessories so as to produce 1 - 1.5m/sec air velocity at floor level for door opening as specified. 153 M&Lfor Sub main wiring Using four single corePVC insulated and unsheathed fire retardant low smoke and halogen(FR-LSH) copper conductor single core multi stranded coppercable 6.0 sqmm( Phase and neutral) and two single core 6.0 sqmm copper conductor PVC insulatedFRLSHcable as continuous earth wire cable confirming to IS:694(2010) using approved colour code for phase and neutralas per IS code drawn through 32mm nominal outer diaERW metallicrigid steel stove enamelled black medium dutyconduit ( Concealed) ISI Marked screwed and socket end ,corrosion resisitant, medium protection grade inaccordance with IS:9537 (Part 2) having wall thickness not less than 1.6 mm thickand external dia as underbut shall be increased as per actual site requirement including conduit accessories( ISI marked) like coupler lock,pipe hooks, nuts,girder clips or clamps bends, tees, junction boxes etc fixedwith all accessoriescomplete all asspecified and as directed by Engr-in-charge. Note :4 runs of 6.0 sqmm copper cable & 2 run of 6.0sqmm copper cable in and including 32mm rigid steel stove enamelled conduit shall be measured as one unit 154 Supply & fix flameproof / weather proof 4 way junction box 2.5 sq mm of 120 mm diacomplete all as specified & as directed by Engineer-in-charge. 155 Supply & fix flameproof / weather proof Elbow M25 complete all as specified & as directed by Engineer-in-charge. 156 Supply & fix flameproof / weather proof bend M25 complete all as specified & as directed by Engineer-in-charge. 157 M&L for Earthing complete with GI earth electrode plate of size 600x600x6mm thick, buried directly in ground(earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.50m below normal ground level, connected to GI wire 4mm dia as earth lead up to test point with suitable GI nuts/bolts and brazed properly up to main board including earth pit in cement concrete 1:2:4 type B-1 using 20mm graded stone aggregates,40mm thick precast RCC cover in 1:2:4 reinforced with expanded metal(weight not less than 4 kg/sqm), and frame of angle iron 25x25x6mm with lugs 02 nos with 6mm dia MS bar handle made to shape, excavation and earth work in any type of soil and including light grade GI watering pipe 20mm bore with funnel andwire mesh and light grade GI earth wire protection pipe 15mm bore up to main board complete as shown in electrical plate no 3 of MES schedule Part-I , connected to earthing testing point and testing on completion complete all as specified anddirected by Engr-in-charge including taking down of old one.

BRR:7509971 Supply, Installation And Commissioning Of Equipment / Machineries For The Laboratories Under Quality Control, (R And B) Division, Bhubaneswar During The Financial Year 2024-25 , Supply, Installation & Commissioning Of Equipment / Machineries , Supply, Installation & Commissioning Of “Rolling Thin Film Oven Tester” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 1 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete. , Supply, Installation & Commissioning Of “Automatic And Digital Ctm Of Capacity- 500Kn And Flexural Testing Machine With 100Kn Capacity With Single Control Panel And Digital Pace Rate Control System” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 2 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete. , Supply, Installation & Commissioning Of “Digital Triaxial Shear Test Apparatus” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 3 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete. , Supply, Installation & Commissioning Of “Humidity Chamber” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 4 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete. , Supply, Installation & Commissioning Of “Ductility Testing Machine (Digitally Controlled & Refrigerated) With Rate Control System” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 5 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete. , Supply Of “Round Hot Plate” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 6 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete. , Supply, Installation & Commissioning Of “Universal Automatic Bitumen Compactor For Compaction Of 4 Inch And 6 Inch Marshal Sample Specimen” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 7 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete. , Supply, Installation & Commissioning Of “Automatic Soil Compactor” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 8 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete. , Supply, Installation & Commissioning Of “Automatic And Digital Marshal Stability Testing Machine” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 9 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete. , Supply, Installation & Commissioning Of “Buoyancy Balance With Density Basket(15Kg-0.1Gm)” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 10 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete. , Supply And Installation Of “Slump Cone Apparatus With Graduated Rod” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 11 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete. , Supplyof “Vicat Apparatus” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 12 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete. , Supply, Installation & Commissioning Of “Concrete Water Permeability Test Equipment” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 13 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete , Supply, Installation & Commissioning Of “Accelerated Curing Tank Stainless Steelwith Heating And Cooling Arrangement” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 14 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete. , Supply Of “Sieve Set-450Mm Dia G.I Sieve ” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 15 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete. , Supply Of “Sieve Set- 200Mm Dia Brass Sieve ” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 16 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete. , Supply Of “Small Sand Pouring Cylinder Of 100 Mm Diameter” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 17 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete. , Supply Of “Large Sand Pouring Cylinder Of 200 Mm Diameter” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 18 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete. , Supply, Installation & Commissioning Of “Aggregate Impact Value Test Apparatus” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 19 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete. , Supply Of “Digital And Electronic Weighing Balance (1 Kg Capacity With Lc 0.01Gm)” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 20 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete. , Supply, Installation & Commissioning Of “Motorized Drum Type Concrete Mixer” Along With All The Accessories As Per The Detailed Technical Specifications Prescribed For Item 21 In The Annexure-Iii Of The Bid Document Inclusive Of All Costs, Cost Of Packing, Transportation, Installation/Commissioning, Demonstration And Any Other Incidental Charges & Excluding Taxes, Gst Etc. Complete.

BRR:7509772 Tender For Special Repair Of Bnk To Patkhauli Rashra Waya Unkhas Road - WBM G-3 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheeled 80-100 kn in stages to proper grade and camber, applying and brooming crushable screening to fill up the interstices of coarse aggregate, watering and compacting to the required density grading-3 as per T.S.C. 405 including labour cess. (GST shall be paid extra) 2 Tack Coat-Providing and applying tack coat with bitumen (VG-10)using bitumen pressure distributor at the rate of 0.30kg per sqm on the prepared bituminous surfacecleaned with Hydraulic broom as per Technical Speicification Clause 503. including labour cess.(GST shall be paid extra) 3 Premix Carpet-Providing, laying and rolling of open-graded premix carpet of 20mm thickness composed of 13.2 & 11.2 mm aggregates either using penetration grade bitumen or emulsion to required line grade and level to serve as wearing coarse on a previously Prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100kN static roller capacity finished to required lavel and grades to be followed by seal coat as per Techincal Specification clause 508 including cost of bitumen & labour cess. (GST shall be paid extra) 4 Seal Coat-Providing and applying seal coat type C comprising of a layer of bituminous binder followed by a cover of stone chipping of specified grading and rolling with power roller 8-10 tonne kN Static roller and finishing to required level and grades as per Technical Specification Clause 510 including cost of bitumen & labour cess.(GST shall be paid extra). 5 Cement Concrete Pavement Construction of un-reinforced, dwel jointed, plain cement concrete pavement over a prepared sub base with approve grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous peration including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per design. including labour cess. 6 Earth Work in Patari as per Si.No. 253.

BRR:7509720 Tender for CC Block Kunda in village Samsapur Sailwara Kakariha Purva Basti - 1 18 % GST Extra 2 Providing, laying, spreading and comapcting stone aggregates of 53-22.4mm size to water bound macadam G-3 specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 KN in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required denisity Grading 3 as per Technical Clause 405 (3) A 3 Construction plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per clause 1501.2.2 M 30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeidng 25mm, mixed in concrete mixer of not less than 0.2 cum capacity and appropriate weight batcher using approved mix design, laid in appropriate weigh batcher using approved mix design, laid in approved fixed side from work (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the from work as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate virbrators and finished in continuous operation. admixtures as approved, curing of concrete slabs for 14 days, curing compound [where specified] and water finishing to lines and grade as per drawing and Technical Specification Clause 1500] 4 E/W in Cutting or filling in embankment in ordinary soil i/c all ramming dressing,etc required for proper complition of work.with One km cartage Extra.SI No. 253 5 S/o 350mmɸ NP-3 Huime Pipe at site i/c all Loading Unloading & Stacking at Site

BRR:7509713 Material Supply For Mahatma Gandhi Nregs Public Works Material Supply , Fine Sand ( Zone Iv ) , Course Sand ( Zone Iii ) , Stone Aggregate ( Single Size ) : 20Mm Nominal Size , Stone Aggregate ( Single Size ) : 40Mm Nominal Size , Stone Aggregate ( Single Size ) :10Mm Nominal Size , Stone Aggregate ( Single Size ) :06Mm Nominal Size , Portland Cement , Stone For Masonry Work , Interlocking C.C Paver Block ( 80Mm Thick, M-30 ) , Twisted Steel Bar , Wall Form Panel , Quarry Waste , Hire Charge Of Concrete Mixer , Vibrator , Precoated Aluminium Trafford Sheet 0.45 Mm , Galvanised Steel J Or L Hook 8Mm Dia , Bitumen Washer , G.I Plain Washer Thick , Wire Nails , Galvanised Wire Mesh , Mild Steel Tubes Hot Finished Welded Type , Welding By Electric Plant , Red Oxide Zinc Chromate Primer , Synthetic Enamel Paint In Black Or Chocolate Shade , Float Glass Sheet Of Nominal Thick 4Mm , Solid Block Of Size 30X20x15cm , Deharadun White Lime , Water Thinnable Cement Primer For Interior Wall , Dry Distemper , Stone Size 24X24x39 Cm , Bright Finished Or Black Enameled Mild Steel Butt Hinges 100X58x1.90 Mm , Bright Finished Or Black Enameled Mild Steel Butt Hinges 50X37x1.50 Mm , Bright Finished Or Black Enameled Mild Steel Screws 40 Mm , Bright Finished Or Black Enameled Mild Steel Screws 20 Mm , Mild Steel Round Bar 12 Mm Dia And Below , Ceramic Glazed Tiles Ist Quality Minimum Thickness 5 Mm In All Colours Shades And Designs Except Burgundy, Bottle Green Black , Ceramic Glazed Tiles Ist Quality 300 X 300 Mm In All Shades And Designs Of White, Ivory, Grey, Fume Red Brown Etc. , Stainless Steel Kitchen Sink - Without Drain Board 470X420 Mm Bowl Depth 178 Mm , C.I. Bracket For Wash Basin And Sinks , G.I. Pipes 25 Mm Dia , Polyethylene Water Storage Tank With Cover And Suitable Locking Arrangemnet , 15 Mm C.P.Brass Tap , Pvc Bend 110 Mm Dia , Anjili Wood Scantls , Pvc Pipe 110 Mm Outer Dia 6Kgf / Cm2 , Pvc Elbow 110 Mm Dia

BRR:7509682 Material Supply For Mahatma Gandhi Nregs Public Works In Agali Gramapanchayat Material Supply , Fine Sand (Zone Iv) , Course Sand (Zone Iii) , Stone Aggregate (Single Size): 20Mm Nominal Size , Stone Aggregate (Single Size): 40Mm Nominal Size , Stone Aggregate (Single Size):10Mm Nominal Size , Stone Aggregate (Single Size):06Mm Nominal Size , Portland Cement , Stone For Masonry Work , Interlocking C.C Paver Block (80Mm Thick, M-30) , Twisted Steel Bar , Wall Form Panel , Quarry Waste , Hire Charge Of Concrete Mixer , Vibrator , Precoated Aluminium Trafford Sheet 0.45 Mm , Galvanised Steel J Or L Hook 8Mm Dia , Bitumen Washer , G.I Plain Washer Thick , Wire Nails , Galvanised Wire Mesh , Mild Steel Tubes Hot Finished Welded Type , Welding By Electric Plant , Red Oxide Zinc Chromate Primer , Synthetic Enamel Paint In Black Or Chocolate Shade , Float Glass Sheet Of Nominal Thick 4Mm , Solid Block Of Size 30X20x15cm , Deharadun White Lime , Water Thinnable Cement Primer For Interior Wall , Dry Distemper , Stone Size 24X24x39 Cm , Bright Finished Or Black Enameled Mild Steel Butt Hinges 100X58x1.90 Mm , Bright Finished Or Black Enameled Mild Steel Butt Hinges 50X37x1.50 Mm , Bright Finished Or Black Enameled Mild Steel Screws 40 Mm , Bright Finished Or Black Enameled Mild Steel Screws 20 Mm , Mild Steel Round Bar 12 Mm Dia And Below , Ceramic Glazed Tiles Ist Quality Minimum Thickness 5 Mm In All Colours Shades And Designs Except Burgundy, Bottle Green Black , Ceramic Glazed Tiles Ist Quality 300 X 300 Mm In All Shades And Designs Of White, Ivory, Grey, Fume Red Brown Etc. , Stainless Steel Kitchen Sink - Without Drain Board 470X420 Mm Bowl Depth 178 Mm , C.I. Bracket For Wash Basin And Sinks , G.I. Pipes 25 Mm Dia , Polyethylene Water Storage Tank With Cover And Suitable Locking Arrangemnet , 15 Mm C.P.Brass Tap , Pvc Bend 110 Mm Dia , Anjili Wood Scantls , Pvc Pipe 110 Mm Outer Dia 6Kgf/Cm2 , Pvc Elbow 110 Mm Dia

BRR:7509662 Tender For Construction Of Smart Village Office At Kalanjoor - CONSTRUCTION OF SMART VILLAGE OFFICE AT KALANJOOR 2 2.31Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared 3 2.6.1Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil 4 4.1.8Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size) 5 7.1.1Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand) 6 2.25Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. 7 5.9.1Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete 8 5.9.6Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts 9 5.9.5Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers 10 5.9.3Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform 11 5.2.2Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) 12 5.3Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 150 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size). 13 5.22.6Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo - Mechanically Treated bars of grade Fe-500D or more 14 50.6.1.2Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete. 15 50.6.1.8Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in: CM 1:6 ( 1 cement : 6 coarse sand etc complete 16 50.6.6.2Hollow block masonry using pre cast solid blocks (factory made) of size 40x20x10cm or nearest available size confirming to IS 2185 part I of 1979 for Super structure up to floor two level for 10 cm thick wall in: CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding etc complete 17 13.7.112 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand) 18 13.7.212 mm cement plaster finished with a floating coat of neat cement of mix:1:4 ( 1 cement : 4 fine sand) 19 13.5.115 mm cement plaster on rough side of single or half brick wall of mix:1:4 ( 1 Cement : 4 coarse sand) 20 50.9.1.1Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Anjili wood /jack wood 21 50.9.2.1Providing and fixing paneled and glazed shutters for doors, windows and clerestory windows, 35 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineerin - charge. using Anjili/ Jack wood 22 9.123Providing and fixing factory made door frame (single rebate) made out of single piece extruded solid PVC foam profile with homogeneous fine cellular structure having smooth outer integral skin having 62 mm width & 32 mm thickness, frame will be mitred & jointed with self driven self tapping screws of size 38 mm x 4 mm & PVC solvent cement, including fixing the frame to wall with suitable dia & length anchor fastener as per manufacturers specification and direction of Engineer-in-charge. 23 9.124.1Providing and fixing factory made 30 mm thick door shutter made of solid PVC foam profile. The styles & rails shall be of size 75 mm x 30 mm having wall thickness 5 mm. The styles, top & bottom rails shall have one side wall thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with M.S. tubes of size 33 mm x 17 mm x 1 mm, painted with primer, all four corners of reinforcement to be welded or sealed. Solid PVC extruded bidding (Push fit type) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5 mm PVC sheet as panel. The styles and rails will be mitred cut and joint with the help of PVC solvent cement & self driven self tapping screws. Single piece extruded solid PVC lock rails of sixe 100mm x 30 mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100 mm x 8 mm complete as per manufacturers specifications and direction of Engineer -in-charge.Non decorative finish 24 21.10Providing and fixing double glazed hermetically sealed glazing in aluminium window, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant ) etc. as per specifications, drawings and direction of Engineer-in-Charge complete. 25 9.48.1Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding 26 11.41.2Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm. 27 11.16.1Precast terrazo tiles 22 mm thick with graded marble chips of size upto 12mm, laid in floors, and landings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) :Light shade pigment using white cement 28 8.31Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 29 11.37Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete. 30 13.43.1Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer 31 13.60.1Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work 32 13.61.1Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work 33 10.28Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) 34 10.16.1Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes 35 21.1.1.2Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) 36 21.2.2Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative lamination on both sides 37 21.3.2Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness 38 21.12.2Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0mm thick & 2100 mm long with S.S. screws etc. complete as per direction of Engineer -in-Charge.Powder coated minimum thickness 50 micron aluminium tubular handle bar 39 21.13Providing and fixing 100 mm brass locks ( best make of approved quality ) for aluminium doors including necessary cutting and making good etc. complete 40 od181986/2021_2022Providing and fixing Hydraulic door closer bottle typr M.S body with neccessary accessories and screws etc complete 41 od181987/2021_2022Supplying and fixing name board with emblem using acrylic sheet base with Reflective type sticker as per required shade and color etc complete.size of Board 3.00mx0.60m 42 od181988/2021_2022Internal name board size 2.5 ft x 1.5 ft using acrylic sheet base with Reflective type sticker as per required shade and color etc complete 43 PLUMBING WORKS 44 17.3.2Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :.c. pan with ISI marked black solid plastic seat and lid 45 18.32.1Constructing masonry chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for stop cock, with C.I. surface box 100x100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:With common burnt clay F.P.S (non modular) bricks of class designation 7.5 46 18.35.1Constructing masonry chamber 120x120x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 grades stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 ( 1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 47 17.7.2Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630 x 450 mm with a single 15 mm C.P. brass pillar tap 48 17.73.2Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighting not less than 190 gms 49 18.51.1Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms 15 mm nominal bore 50 18.16.1Providing and fixing brass stop cock of approved quality : 15 mm nominal bore 51 18.65Providing and fixing PTMT Soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fittings arrangements, weighing not less than 106 gms. 52 17.32.2Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 453x357 mm 53 18.48Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 54 50.18.7.2.1Providing and fixing PVC pipes, fittings including fixing the pipe with claps at 1.00 metre spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 20 mm dia 12Kgf/cm2 - Internal work - Exposed on wall 55 50.18.7.6.1Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 10 Kfg/cm - Internal work- Exposed on wall 56 50.18.9.9.1Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2 57 50.17.1.5Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge. 58 50.18.9.22.1Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow 59 50.18.9.22.4Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend 60 od181979/2021_2022Providing and fixing 150mm silt with CP gratings 61 17.5.1Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required:Single half stall urinal with 5 litre PVC. automatic flushing cistern 62 51.19.ST2Supplying and installing ready made PVC Septic tank including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (Provision for CC/RCC/Sand/06mm aggregate for the preparation of bed shall be paid separately) 2. 15 to below 25 flush capacity 63 ELECTRICAL 64 1.10.3Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C 65 1.12Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 66 2.3.2Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator 8 way, Double door 67 90.11.1.21Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required 12 way (8+36) - double cover TPN vertical DB with provision for fixing MCCB as incomer and SP/ TP MCB as outgoing (IP 42/43) 68 1.24.3Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 amp switch 69 1.24.5Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet 70 1.14.2Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required 2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 71 1.25Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. 72 5.4Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. 73 5.19Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. 74 1.27.2Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm) 75 1.28.2Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.3 Module 76 1.26Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. 77 1.14.4Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required 2 X 6 Sq.mm + 1 x 6 sq.mm earth wire 78 1.14.6Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required 2 X 16 sq. mm + 1 X 6 sq. mm earth wire 79 2.14.3Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps 80 8/2021_2022Supplying and fixing 6A to 32 A ratings, SP MCB and other accessories 81 1.14.1Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required 2x1.5 sq.mm + 1x1.5 sq.mm earth wire 82 2.13.2Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps 83 od181980/2021_2022Supplying and fixing following 32 amps modular DP switch and other accessories etc complete 84 od181981/2021_2022Supplying and fixing angle batten with 23 watts C FL and other accessories 85 od345763/2023_2024Supplying and fixing LED tube 86 od181983/2021_2022Supplying and fixing 48 ceiling fan and other accessories 87 od181984/2021_2022Supplying and fixing 12 Exhaust fan and other accessories 88 od345837/2023_2024Supplying, installation, testing and commissioning of all wall mounted Single phase 2 wire energy meter with poly carbonate body having range of 32 Amp with enclosure made out of powder coated fixing in surface / recess with fuse unit 32 amp with neutral link, its connections etc. The enclosure shall have lockable door with glass window and all mounting accessories etc. complete as required including KSEB Charges. 89 WORKSTATION AND FURNITURE 90 od181957/2021_2022Providing modular work station using 1 nova pan on table top and 3/4 nova pan are side pannel and drawyer keyboard etc, and the edges are finishing with pvc ban of suitable colour of nova pand providing telescao channel on keyboard tray, drawyers and providing handles, locking arrangements etc, complete-pentagonal work station (L shape 1.55x1.75m) 91 od181962/2021_2022Supplying office chair (high back) 92 od181965/2021_2022Supplying office chair (midback) 93 od181968/2021_2022Supplying visitor chair with arm 94 od346163/2023_2024Supplying Airport type chair of 3 seater capacity Nilkamal 95 od181974/2021_2022Supplying meeting table of dia 1.00m using manufacturing wood of required shade etc. complete 96 COMPUTER NETWORK AND TELEPHONE CABLING 97 od181956/2021_2022Providing network cabling using cat 6 cable through 1 case and caping and giving connection including all labour charges material cost, grimping and connectiong etc. complete 98 od181959/2021_2022Engaged a Computer Engineer for programming all network and commisionong etc. complete ( 1 Racksx2000=2000) 99 od181963/2021_2022Supplying and fixing PATCH CORD 0.50M on bottom and grimping two ends 100 od181964/2021_2022Supplying and fixing PATCH CORD 0.50M on top and grimping two ends 101 od181967/2021_2022Supplying and fixing 3 M PATCH CORD and grimping two ends 102 od181970/2021_2022Supplying and fixing 2M PATCH CORD and grimping two ends 103 od181972/2021_2022Supplying and fixing 1M PATCH CORD and grimping two ends 104 od181973/2021_2022Supplying and fixing patch pannel and giving connection 105 od181975/2021_2022Supplying and fixing 16 port switch and giving connection 106 od181976/2021_2022Supplying and fixing 4U rack and giving connection 107 od181977/2021_2022Supplying and fixing roset box and grimping the ends etc. complete 108 TELEPHONE CABLING 109 od181955/2021_2022Supplying and drawing two pair telephone cable through 1 case and caping and giving connection 110 od181960/2021_2022Supplying and fixing IO box set and giving connection 111 od181961/2021_2022Supplying and fixing roset box and giving connection 112 od181966/2021_2022Supplying and fixing ordinary type telephone (BPL make) and other accessories

BRR:7509408 Tender For Special Repairs To Building No P-106 At Ramnad Under Ge Tirunelveli(Tender Id:2025_Mes_ 697977_2); 1 Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing and rubbish off the premises complete allas directed. 2 Material and labour vitrified ceramic tiles 10mm thick (Square/rectangular) area of each tile not exceeding 0.36 sqmin floorsset and jointed in neat cement slurry and pointed in white or coloured cement to matchincluding screed bed or bedding layer of mortar 15 mm thick in CM 1:6complete all as specified. 3 All as per item no 02 above but in vertical surfaces including backing coat of 10mm thick in CM 1:4on brick walls for skirting/DADO complete all as specified and as directed. 4 Material and labour Non Skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm in floors etc. set and jointed in neat cement slurryand pointed in white or coloured cement to match including 15 mm thick screed bed in CM 1:6 in floors etc complete all as specified and as directed. 5 Material and labour for 450x350x7mm thick glazed coloured ceramic tiles in vertical surfaces set and jointed in neat cement slurry pointed in coloured cement to match over backing coat of 10mm thick in CM 1:4complete all as specified and directed. 6 Material and labour Machine cutpre polished kota stone slab flooring 20-25mm thick over cement screedbase15mm thick in CM 1:6laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed. 7 Material and labour kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed including backing coat of 10mm thick in CM 1:4on brick walls for skirting/DADO complete all as specified and as directed. 8 Supply and fixing 15mm Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc.,with all fittings including taking down old existing pipe complete all as specified and as directed. 9 Supply and fixing 20mm Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc.,with all fittings including taking down old existing pipe complete all as specified and as directed. 10 Supply and fixing in repair vitreous China wash down water closet pan (pedestal pattern) white, incl. P or Strap, connection to drain and flushing pipe including seat cover for pedestal pan complete all as specified and as directed. 11 Supply and fixing in repairs vitreous China wash basin white, flat back, size 550X400 mm including cutting for pinning in ends of brackets, complete all as specified and as directed. 12 Supply and fixing in repairs 10 litre capacity PVC low level flushing cisternwith all accessories complete fixed with WC including syphonic pipe, PVC flushing pipe of size 32mm dia complete all as specified and directed. 13 Supply and fixing in repairs 15mm dia bore stop cock/angle cock, cast fancy type chromium plated screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe on for unions and fixed complete all as specified and as directed. 14 Supply and fixingPVC connection 15mm dia and 450mm long with PTMT nuts complete all as directed. 15 Supply and fixing in repairs CP brass chromium plated shower rose 125 mm size fixed to 15mm pipe of revolving type complete all as specified and as directed. 16 Supply and fixing as in repair grating square 100mm size of PTMT(minimum 100 gms) complete all as specified and as directed. 17 Supply and fixing in repairsbib taps fancy type 15mm dia bore, chromium plated,with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed. 18 Supply and fixing in repairs pillar taps, fancy type 15mm dia bore, chromium plated, screwed down high pressure, with or without lettered `Hot or `Cold with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed. 19 Supply and fixing in repairs 5.50mm thick of size600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. 20 Material and labour in repair 75 mm dia PVC(SWR) floor trap with grating including jointing with solvent cement complete all as specified and directed. 21 Material and labour in repair 110mm dia PVC(SWR) gully trap setting and hoisting with solvent cement complete all as specified and directed. 22 Supply and fixing rotational moulded polyethylene water storage tanks 500 ltrs capacity (White colour), three layer (cylindrical or vertical with closed top) hoisted and fixed in position, including dismantling the existing one and removing to MES store yard, including dismantling water tanks complete all as specified and as directed. 23 Supply and fixing in repair for 20 mm dia bore Ball brass valves, high pressure, with polythene float and fly nutscrewed for iron pipe or brass ferrule and fixed all as specified and as directed. 24 Supply and fixing in repairs 20 mmdia gun metal, globe or gate valves, with iron head, screwed both ends for iron pipe all as specified and as directed. 25 Supply and fixing in repairs Tubular towel rail aluminium anodised powder coated, 20mm dia, D type, 60cm long between flanges all as specified and as directed. 26 Taking down old door or window or cup board Chowkhats or frames n.exc 1.50 sqm each with shutters but without taking off shutters from the frames complete all as specified and directed. 27 Taking down door or window or cupboard Chowkhats of frames of size exc 1.5 sq.m but n exc 4sqm each with shutters (Without takingof shutters from the frame) complete all as specified and directed. 28 Supply and fixing powder coated Anodised aluminium window and ventilator shutters, sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified. 29 Supply and fixing anodised aluminium door shutters aluminium section 0.55kg/m including necessary joining cleats , glazing clips, rubber neoprene packing, handles 2 nos in each door, hinges, anodised aluminium snap beading screws etc with powder coating complete all as specified and directed. 30 Supply and fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing. 31 Supply and fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube,as per specification & drawing. 32 Material and labour 18mm thick PVC cupboard Frames & shutters with decorative face veneers on both faces including necessary hinges, handles and locks fixed with screws all as specified and as directed. 33 Supply and fixing powder coated aluminium frame for doors, windows, ventilators, partitions with one or more rebates including anodised aluminium snap beading, stainless steel screws joining cleat for fixing etc complete all as specified and as directed 34 Supply and fixing 4.8mm thickfrosted sheet glass ordinary quality fixing with necessary rubber gasket and beadings etc in squares exc 0.50 sqm in each pane complete all as specified and as directed. 35 Material and labour for 12mm thk prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specifiedand as directed 36 Supply and fixing 100mm mild steel butt hinges medium weight including screws complete all as specified and as directed. 37 Supply and fixing aluminium anodisedbarrel tower bolts 150mm of extruded section complete all as specified and directed. 38 Supply and fixing aluminium handle 125 mm cast type anodised complete all as specified and directed. 39 Supply and fixing 250 mmlongAluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed. 40 Taking down cement plaster of any description on bricks or stone walls , RCC ceiling etc, including racking out joints, hacking for keys, scrubbing down with water etc, all as specified and as directed. 41 Material and labour for 15 mm thick cement plaster in two coats 5mm thk in CM 1:4 with WPC over 10mm thk in CM 1:6 on brick wall or concrete surfaceand finish the surface fair and even complete all as specified and directed. 42 Material and labour Preparation of new plastered surface on wall by and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed . 43 Material and labour for 10 mm thick cement plaster in CM(1:6) on brick wall or concrete surface finish the surface fair and even without using extra cement complete all as specified and directed. 44 Material and labour preparation ofnew plastered wall surfacesand applying two coats of oil bound distemperover a coat of primer and a coat of1mm wall care putty all as specified and as directed . 45 Material and labour for 5mm thickin CM(1:3) on ceiling and finish the surface fair and even without using extra cement complete all as specified and directed. 46 Material and labour preparation of newly plastered ceiling surfaces and applying two coats of oil bound distemper over a coat of primer all as specified and as directed . 47 Material and labour complete removal of existing painted wall surfaces and applying two coat or more of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm in camouflage pattern complete all as specified and as directed 48 Material and labour complete removal of existing painted wall surfaces and applying two coats of Oil bound distemperover a coat of primer and 1mm thk wall care puttycomplete all as specified and as directed. 49 Material and labour complete removal of existing painted ceiling surfaces and applying two coats of Oil bound distemper over a coat of primer complete all as specified and as directed. 50 Material and labour for preparation of old painted surfaces of wood or wood based surfaces over 10cm width or girth and applying one coat of synthetic enamel paint on wooden surfaces complete all as specified and as directed. 51 Material and labour for preparation of old painted steel/roof surfaces any description over 10cm girth and applying one finishing coat of synthetic enamel paint on steel surfaces complete all as specified and as directed. 52 M& L for complete removal of existing roof treatmentfrom roof slabincluding taking down existingcement mortar, cleaning of the rubbishes and disposal of the same to a distance n exc 250 m. complete all as specified and as directed. 53 Supply only integral water proofing compound 54 Material and labour for complete removal of existing roof treatmentfrom roof slabincluding taking down existingcement mortar, cleaning of the rubbishes and disposal of the same to a distance n exc 250 m. and providing APP based membrane roof treatment in layers with the following course of treatment from bottom to top :-(a) Brushing neat cement slurry with 3.0 kg of cement per sqm(b) Screed bed or bedding layer of mortar 20mm thick in CM 1:4 with WPC @ 3% of weight of cement(c) Applying bituminous primer @ 0.40 Lit/Sqmover plastered surfaces of roof slab including parapet wall. (d) APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3mm thick reinforced with polyester non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by torch application complete all as specified. Polymeric membrane shall be taken to a height of 45 cm (minimum) and then inserted inside the groove of parapet wall and shall be filled with bitumen mastic filling.(e) Applying two coats of bituminous Aluminium paints on top of APP membrane surfaces @ rate of 0.10 Lit/Sqm for each coat. 55 Note :(i) The work in respect of water proofing treatment shall be carried out only by authorized / approved applicator of the manufacturers / firms of APP membrane. The contractor shall produce the evidence in support of work carried out by the authorized applicator as approved by manufacturers / firms before claiming payment.(ii) Laying APP based polymeric membrane shall be done by torch on method or as per manufacturers instructions.(iii) A minimum overlap of 150mm and 100mm should be made at the end and side of the polymeric membrane respectively and sealed overlaps and joints as per manufacturers instructions. (iv) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces. 56 Demolition of cement concrete reinforced Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work all as specified and as directed. 57 Material and labour providing, RCC in Fins, fascias, louvers, parapets, and railings exc. 60cm in height, newels, balustrade, and the like using type B1(20mm graded aggregate) complete all as specified and as directed. 58 Formwork to fins, louvers, fascia complete all as specified and as directed. 59 Supply and fixing Mild steel bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends bindingand welded to existing bar with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips along with necessary formwork complete all as specified and as directed. 60 Supply and fixing in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. 61 Supply and fixing 110mm in repairs PVC (SWR) pipes double socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed. 62 Supply and Fix in repair Vitreous China bowl Urinal , flat back, size of 465 x 355 x 265mm white (minimum), with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs brass screws pointing around urinal for discharge pipe complete all as specified and directed. 63 Supply and fix Waste coupling of PTMT 32mm bore dia of discharge pipe (half or full threaded)(Minimum weight 32mm -45gms) for urinals fixed complete all as specified and as directed. 64 Supply and fixing PVC (SWR) Vent cowl of bore dia 110mm complete all as specified and as directed. 65 Supply and Fix door stopper of aluminium alloy,anodised with hard drawn steel spring of length 150mm complete all as specified and as directed. 66 Supply and fixing Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in- charge. 67 Supply and fix Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed. 68 Demolition Concrete in ground floors unreinforced and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed. 69 Material and labour for 75mm thick cement concrete type C-2, ( 1:3:6) (40 mm graded aggregate) as in plinth protection finished fair and even without using extra cement etccomplete all as specified and as directed. 70 Supply and fixing in repairs Harrison curtain rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and as directed. 71 Supply and fix in repairs door closer hydraulically regulated aluminium extruded section, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as specified and as directed. 72 Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. 73 Material and labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc.,including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the floor or the side of waist slab with suitable arrangement complete all as specified and as directed. 74 Supply and fixing 75mm dia PVC (SWR) pipes double socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed. 75 Supply and fixing 75mm dia PVC (SWR) pipes double socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed. 76 Supply and fixing 110mm dia PVC (SWR) bends complete all as specified and as directed. 77 Supply and fixing 110mm dia PVC (SWR) branch piece, double (double Y) equal or unequal complete all as specified and as directed. 78 Material and labour 25mm thk Cement concrete type B-1, 1:2:4 (20mm graded aggregate) complete all as specified and as directed. 79 Supply and fixing 32 mm dia Low density polyethylene pipes (LDPE) of pressure rating 6 kg/ cm2 on wall complete all as specified and as directed. 80 Taking down copper/aluminium point wiring (light, fan, socket or power)including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc., removing materials to store for keeping in safe custody for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc complete all as specified and as directed. 81 Material and labour for point wiring in replacement with two single core 1100 V grade FRLS-H conforming to IS-694 PVC insulated unsheathed cables of size 1.5 Sq mm multi-stranded Copper conductor drawn through and including rigid PVC conduit and conduit accessories fixed on surface including breaking of walls and making good to disturbed surfaces in wall/roof/ceiling where required completean earth wire of PVC cable 1.5 Sqmm multi stranded copper conductor and connected to all metal boxes and common earth dolly all as specified and directed for the following :- 82 (a) One light point , controlled by one switch complete 83 (a) One light point , controlled by two switch complete 84 (b) One fan point, controlled by one switch complete 85 (c) One 3 pin 5 Amps switch socket combination on independent board 86 (d) One 3 pin 5 Amps switch socket combination on the same board with other switches, 87 All as per item No 80 above butwith 4.0 Sqmm single core PVC sheathed FRLS-H copper conductor cable, with PVC conduit for 3 pin socket outlet 15 amps on independent board 88 Supply and fixing ceiling rose in replacement , surface bakelite, 65x50mm, two to three terminals complete all as specified and as directed by the Engineer-in-Charge 89 Supply and fix in replacementswitch piano flush type single pole one way 5 A 240 Volts complete all as specified and as directed 90 Supply and fix in replacementswitch flush type single pole two way 5 A 240 Volts complete all as specified and as directed. 91 Supply and fix in replacement Socket outlet 3 pin, 5A, flush type complete all as specified and as directed. 92 Supply and fix in replacement switch Socketcombination 2 in 1,5 Amps Flush type 240 Voltscomplete all as specified and as directed. 93 Supply and fix in replacement switch Socketcombination 5 Amps / 16 amps, 5 in 1 flush type 240 Voltscomplete all as specified and as directed. 94 Supply and fixing in replacement of Stepped type Electronic Fan Regulator, Flush type on the existing phenolic laminated sheet complete all as specified and as directed. 95 Supply and fix in replacementfor Wiring for Circuit / Sub main Wiring of size 4x4.0 sq. mm along with earth wire of size 2 x 4.0 sq.mm, Single Core, PVC insulated copper conductor FRLS-H Cable in surface / recessed PVC Conduit of 32 mm dia complete all as specified and as directed.Note: Four runs of main cable, 2 runs of earth wire and one run of PVC conduit shall be measured as one unit for payment. 96 Supply and fixin replacement for Wiring for Circuit / Sub main Wiring of size 2 runs of 2.5 sq.mm along with earth wire of size 1 run of 2.5 sq.mm, Single Core, PVC insulated copper conductor FRLS-H Cable in surface / recessed PVC Conduit of 25 mm dia complete all as specified and as directed.Note: Four runs of main cable, 2 runs of earth wire and one run of PVC conduit shall be measured as one unit for payment. 97 Supply and fix in replacement sheet metal enclosure powder coated double door for Distribution Board,TPN 6 way prewired DBsuitable forMCB Incomer IP 43 , IK 09 ,including disconnecting electric connections complete all as specified and as directed. 98 Supply and fix in replacement sheet metal enclosure powder coated double door for Distribution Board,TPN 4 way prewired DBsuitable forMCB Incomer IP 43 , IK 09 ,including disconnecting electric connections complete all as specified and as directed. 99 Supply and fix in replacement415V 10KA B curve miniature circuit breaker (MCB) of TPN 40 A in the DB complete including testing and commissioning complete all as specified and as directed. 100 Supply and fix in replacement415V 10KA B curve miniature circuit breaker (MCB) of TPN 16 A in the DB complete including testing and commissioning complete all as specified and as directed. 101 Supply and fixMCB SP 6 A, B curve, 10 kA including , disconnecting electric connections, dismantling from position unserviceable MCB for taking into credit completeall as specified and as directed. 102 Supply and Fix in replacementLED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed 103 Supply and fix in replacement LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. . 104 Supply and fix in replacement LED light fitting 1x9W/1X10Wbulkhead luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. 105 Supply and fixing in replacement ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated complete all as specified and directed. 106 Supply and fix exhaust fan in replacement , steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louverscomplete all as specified and directed. 107 Material and labour for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; andconcealed conduit wiring, etc., and making good and painting to match with existing wall colour, cutting not exc 10cm girth in brick walls complete all as specified and as directed by the Engineer-in-Charge 108 Supply and fix in replacementGI bracket made out of 32 mm dia GI pipe length 1.2 mtr long bent to an angle 135 degreepainted with two coats of aluminium paint over a coat of zinc chromate primer along with clamps, bolts, nuts etc complete allas specified. 109 Supply , erection, testing ofmaintenance free chemical earthing byauguring & installation of copper bonded rod using machine bore and filling with backfill compound.The specification is (a) Low Carbon High Tensile Steel rod copper bonded rod of dia 20.2 mm with Copper Plated (250+ microns) , length 3m , with top end of the rodconnected with copper plated welded bus bar terminal of dimension 150mm x 50mm x 6 mm, complete conforms to IS : 3043 - 1987 (b) The earth pit bore dia should be 150 mm and length 3 m(c) Backfill compound with following specification has be filled in the bore after placing the copper bonded rod : - Carbon based, high conductive backfill compound Conductolite(50 kg per electrode to be filled around each electrode )with resistivity< 0.5 ohm-metre (In dry conditions) & resistivity is non-moisture dependant,pH Value : 8.0 - 9.0, electronic & ionic conduction, less susceptible to shrinkage, with hygroscopic & corrosion resistive properties (d)covering with Heavy duty Earth pit Chamber cover made of HDPE with high strength to weight ratio ( Capable of withstanding upto 8 ton) , Bottom opening dia - 348 mm Top opening dia - 256 mm, Height -260mm . Make : M/s Ashlok Safe Earthing Electrode Limited. Code : ASEEL CBR 203 250 WBB 110 Material and labour for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4 mm dia galvanised iron or steel wirecomplete all as specified and as directed by the Engineer-in-Charge 111 Supply and fixing in replacement LED building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

BRR:7509169 Bids Are Invited For Air Canon For Ls Day Silo-Ba9789360002 , E& C Supervision Of Air Canon At Site , Air Nozzle Total Quantity : 4

BRR:7509168 Bids Are Invited For Bag Filter For Ls Day Silo Ba989359004,Bag Filter For Ls Day Silo, Ba89359-R00 , Supervision Of E And C And Testing At Ntpc Talcher Site Per Set , Ba989212011,Fan Motor, Ba89212-01 , Ba9789212038,Bearings Of Fan And Motor,Ba89212-03 , Ba9789212070,Motor Terminal Blocks With Studs,Ba89212-07 , Filter Sand Total Quantity : 7

BRR:7508011 Bids Are Invited For Custom Bid for Services - Operation of Baggage Handling System including AICMC of standalone weighing scales at MBB Airport, Agartala Operation And Maintenance Of Electro-Mechanical Installations Total Quantity :

BRR:7507779 Bids Are Invited For Microsemi-Microanalytical Weighing Balance (Q2) Total Quantity : 1

BRR:7507298 Tender For Providing Vikravandi Block; 1 Strengthening the road from Vembi - Poondiroad, Km 0/0 - 2/050 2 Clearing the scrub jungles including all labour charges for all labour charges etc complete. 3 Km 0/0 - 2/05 4 Earthwork excavation in all classes of soils except hard rock requiring blasting and depositing on bank with all leads and lifts as per SS20A including cost of all labour materials, tools, equipments and all incidental charges and sheeting, shoring and br 5 Km 0/0 - 2/05 6 Picking the Existing damaged BT Surface 7 Km 0/0 - 2/05 8 Collection and supply of US gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for spreadingetc.complete, 9 Km 0/0 - 2/05 10 Km 0/0 - 2/0 11 Km2/0 - 2/05 12 Providing and laying spreading and compacting graded stone aggregate to Wet Mix Macadam(WMM) specification including premixing the material with water at OMC in machanical mix plant carriage of mixed material by tipper to site laying in uniform layers 250mm thick with pavers in SubBase/Base course on well prepared surface and compacting with vibratory roller to achieve the desired density including cost of material,labour charges, rentals for machinery, fuel and all other incidental charges etc., complete. 13 Km 0/0 - 2/05 14 Km 0/0 - 2/0 15 Km2/0 - 2/05 16 Providing and laying of prime coat using Emulsion at the rate of 7 Kg per ten square meter over the WMM surface preparatory to another bituminous construction over it. 17 Km 0/0 - 2/05 18 Providing and laying Tack coat over BT surface using 3Kg of bitumen 60/70 for 10sqm area including cost and conveyance of bituminous binder including labour charges for preparing the surface and applying the required quantity of bitumen as tack coat by b 19 Km 0/0 - 2/05 20 BITUMINOUS CONCRETE 40 MMTHICK USING cmp (Grade-II) Providing and laying Bituminious concrete to 40mm thick using 0.13cum of 19.00-9.50mm. 0.17cum of 9.5-2.36 and below with 50.3kgs of VG30/VG40 heating the bitumen and aggr 21 Km 0/0 - 2/05 22 Km 0/0 - 2/0 23 Km2/0 - 2/05 24 Provision of 15 nos of rumble strips covered with premix bituminous carpet, 15 - 20 mm high at centre, 250 mm wide placed at 1 m center-to-centre at approved locations to control speed, marked with white strips of road marking paint. 25 Km 0/0 - 2/05 26 Construction of Retaining wall @ CH 10m - 35m 27 Earth work excavation for foundation in all classes of soils except hard rock requiring blastingwith initial lead and lift etc including levelling the site etc. complete with standard specification in hard stiff cllay, black cotton soil, hard fred earth 28 Cement Concrete 1:4:8 Using 40mm ISS size Hand Broken granite stone jellyincluding labour charges for mixing concrete watering and laying the concrete in layers not more the 15 cm thick compacting etc complete complying with standard specification etc c 29 Supplying and erecting shuttering including complying with standard speficiation including all labour charges etc.complete. 30 Cement Concrete : 1:3:6 with broken stone using 40mm gauage machine broken HBG metal including cost and conveyance and all labour charges etc.complete. 31 Supply and fixing PVC pipes for weep holes 32 Construction of 3.00m Span RCC slab culvert @ CH 534 m 33 Earth work excavation and depositing on bank with in initial lead of 10 m and initial lift of 2m in hard stiff clay, stiff black cotton soil, hard red earth,earth mixed with small sized boulders and hard gravelly soil as per SS 20B. 34 Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete. 35 Supplying and erecting centring for sides and suffits including supports and structing upto 3.29m height for plane surface in all cross bracting using MS sheets of size 90 x 60cm and 10kg stiffened with angle of size 25 x 25 x 3mm for boarding laid over silver oak joists os size 10 x 6.5mm at about 90cm C/C and supported by casuring props of 10cm 13cm dia at C/C etc., complete. 36 Below Sill 37 Above Sill 38 Cement concrete 1:3:6 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete. 39 Cement concrete 1:2:4 mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete. 40 Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works. 41 Reinforced cement concrete 1:1 1/2:3 mix using 20mmISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum 42 Provision for Bitumen Pads 43 Provision forWheep Holes 44 Construction of 1.50m Span RCC slab culvert @ CH 646 m 45 Earth work excavation and depositing on bank with in initial lead of 10 m and initial lift of 2m in hard stiff clay, stiff black cotton soil, hard red earth,earth mixed with small sized boulders and hard gravelly soil as per SS 20B. 46 Cement concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete. 47 Supplying and erecting centring for sides and suffits including supports and structing upto 3.29m height for plane surface in all cross bracting using MS sheets of size 90 x 60cm and 10kg stiffened with angle of size 25 x 25 x 3mm for boarding laid over silver oak joists os size 10 x 6.5mm at about 90cm C/C and supported by casuring props of 10cm 13cm dia at C/C etc., complete. 48 Below Sill 49 Above Sill 50 Cement concrete 1:3:6 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete. 51 Cement concrete 1:2:4 mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete. 52 Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length, bending to shape and tying in position and forming grills for all R.C.C works. 53 Reinforced cement concrete 1:1 1/2:3 mix using 20mmISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete for 10 cum 54 Provision for Bitumen Pads 55 Provision forWheep Holes 56 Provision for KM Stones. 57 Provision for HM Stones of size 75 x 23 x 10 cm. 58 Provision for 60Cm Equilateral Triangular Sign board Charges 59 Provision for Citizencum Name board Charges 60 Provision for Photographic Charges 61 GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column BB for all works in this package}

BRR:7507238 Tender For Strengthening The Road From Velanthangal Sozhanthangal Road 0/0-2/580; 1 Strengthening the road from Velanthangal Sozhanthangalroad 0/0-2/580 2 Clearing the scrub jungles including all labour charges for all labour charges etc complete. 3 in Km. 0/0 - 2/580 4 Earthwork excavation in all classes of soils except hard rock requiring blasting and depositing on bank with all leads and lifts as per SS20A including cost of all labour materials, tools, equipments and all incidental charges and sheeting, shoring and br 5 in Km. 0/0 - 2/580 6 Picking the existing damaged BT surface to 3 - 5cm deep including all labour charges 7 in Km. 0/0 - 2/580 8 Providing and laying spreading and compacting graded stone aggregate to Wet Mix Macadam(WMM) specification including premixing the material with water at OMC in machanical mix plant carriage of mixed material by tipper to site laying in uniform layers 250mm thick with pavers in SubBase/Base course on well prepared surface and compacting with vibratory roller to achieve the desired density including cost of material,labour charges, rentals for machinery, fuel and all other incidental charges etc., complete. 9 in Km. 0/0 - 2/580 10 Providing and laying of prime coat using Emulsion at the rate of 7 Kg per ten square meter over the WMM surface preparatory to another bituminous construction over it. 11 in Km. 0/0 - 2/580 12 Providing and laying Tack coat over WMM surface(treated with primer) using 2.5Kg of bitumen emulsion RS-1for 10sqm for preparatory to another bituminous construction over it including cost of material, labour charges, rentals for machinery, fuel and all 13 in Km. 0/0 - 2/580 14 BITUMINOUS CONCRETE 25 MMTHICK USING cmp (Grade-II) Providing and laying Bituminious concrete to 40mm thick using 0.13cum of 19.00-9.50mm. 0.17cum of 9.5-2.36 and below with 50.3kgs of VG30/VG40 heating the bitumen and aggregates to required temperature and mixing them in required temperature in central hot mix plant 20-30 ton capacity, carrying the mix by tipper trucks to paver site, spreading the mix to uniform thickness of 40mm with mechanical paver to the specified grades and cross sections and consolidated by 8-10 tonnes vibratory/phenumatic roller to the required density etc., including labour for attending to paver to site etc.including hire charges and fuel charges foe 20-30t CMP with bitumen boiler, tipper trucks,paver finisher/9m paver finisher,vibratory/phenumatic roller and all other tools and plants required, including fuel and all other incidental charges etc., complete as per specification using CMP as per clauses 507 of MORTH Part-5 15 in Km. 0/0 - 2/580 16 LayingUS GRAVEL including cost and conveyance and stacking at site to departmental gauge for taking pre measurements by departmental officers and including labour charges for spreading the gravelas per standard specification etc. complete. 17 in Km. 0/0 - 1/0 18 in Km. 1/0 - 2/0 19 in Km. 2/0 - 2/580 20 Provision of 15 nos of rumble strips covered with premix bituminous carpet, 15 - 20 mm high at centre, 250 mm wide placed at 1 m center-to-centre at approved locations to control speed, marked with white strips of road marking paint. 21 in Km. 0/0 - 1/330 22 Providing and Laying of hot applied Thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes etc complete as per MORTH specification No.803 23 in Km. 0/0 - 2/580 24 Provision for KM stone 25 Provision for HM stone 26 Provision for 60cm Equilateral Triangular board 27 Provision for 60cm Equilateral sign board charges 28 Construction of 1.50m span RCC slab Culvert @ CH 150m 29 Earth work excavation for foundation in all classes of soils except hard rock requiring blastingwith initial lead and lift etc including levelling the site etc. complete with standard specification in hard stiff cllay, black cotton soil, hard fred earth 30 Cement Concrete 1:4:8 Using 40mm ISS size Hand Broken granite stone jellyincluding labour charges for mixing concrete watering and laying the concrete in layers not more the 15 cm thick compacting etc complete complying with standard specification etc 31 Supplying and erecting shuttering including complying with standard speficiation including all labour charges etc.complete. 32 Below sill level 33 Above sill level 34 Cement Concrete : 1:3:6 with broken stone using 40mm gauage machine broken HBG metal including cost and conveyance and all labour charges etc.complete. 35 Cement Concrete : 1:2:4 with broken stone using 20mm gauage machine broken HBG metal including cost and conveyance and all labour charges etc.complete. 36 Supplying and fabrication of steel including cost and conveyence of steel to site including cost and conveyance and all labour charges etc.complete. 37 Reinforced Cement Concrete : 1:1 1/2:3 with broken stone using 20mm gauage machine broken HBG metal including cost and conveyance and all labour charges etc.complete. 38 Provision for Bitumen pads 39 Provision for the wheep holes 40 Provision for Nameboard Cum Citizen board charges 41 Provision for photographic charges 42 GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column BB for all works in this package}

BRR:7506774 Tender For Civil Maintenance Work In Type-5 And Type-6 Residences Located In Raj Bhavan Colony - Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes , having thermal stability for hot & cold water supply , including all CPVC plain & threaded fittings . This includes jointing of pipe & fitting with one step CPVC solvent cement trenching , refilling &testing joints complete as per direction of Engineer - in - charge: exposed on wall (25 mm nominal dia pipes)(18.7.3) 2 Providing and fixing 20mm diachlorinated polyvinyl chloride (cpvp )pipes , having thermal stability for hot & cold water supply including the supply with clamps at 1.00m spacing . This includes jointing of pipe and fiting with one step salvent cement and testing of joints complete as per direction of Engineer in charge -Internal work - Exposed on wall (dar-18.7.2) 3 ProvidingandfixingG.I.pipescompletewithG.I.fittingsandclamps, including cutting and making good the walls etc. Internal work- Exposed on wall 15 mm dia nominal bore(dar-18.10.1) 4 ProvidingandfixingG.I.pipescompletewithG.I.fittingsandclamps, including cutting and making good the walls etc. Internal work- Exposed on wall 20 mm dia nominal bore(dar-18.10.2) 5 Providing and fixing20 mm diaball valve(brass) of approved quality,high or low pressure , with plastic floats complete(dar-18.18.2) 6 Providing and fixing15mm diaball valve(brass) of approved quality,high or low pressure , with plastic floats complete(dar-18.18.1) 7 Providing and fixing c.p brass shower rose with 15 or mm inlet :150 mm dia meter (dar-18.22.2) 8 Providing and fixing G.I union in g.i pipe including cutting and threading the pipes ans making long screws etc complete - New work 15 mm nominal bore(18.46.1) 9 Providing and fixing G.I union in g.i pipe including cutting and threading the pipes ans making long screws etc complete - New work 20 mm nominal bore(18.46.2) 10 Providing and fixing c.p brass angle valve for basin mixer and geyser point of approved quality conforming to IS:8931 15 mm nominal bore (dar-18.53.1) 11 Providing and fixing PTMT Ball cock of approved quality , colour and making complete with epoxy aluminium rod with L.P/ H.P.H.D plastic ball :15 mm nominal bore , 105 mm long weighingnot less than 138gms(dar-18.62.1) 12 Providing and fixing 8 mm dia c.p / ss jet with flaxible tube upto 1 meter long s.s triangular plate to European type w.c of quality and make as approved by engineer in charge (DAR-17.16A) 13 providing and fixing p.v.c low level flushing cistern with manually controlled device (handle lever) conforming to is :7231 with all fitting and fixtures complete (10 litre capacity -white )(dar-17.18.1 14 Providing and fixing P.V.C waste pipe for sink or wash basin including P.V.C waste fitting complete . Semi rigid pipe ,32 mm dia /40 mm dia (dar-17.28.1.1) 15 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality ) complete with 6 mm thick hard board ground fixed to wooden cleats with c.p brass screws and washers complete(dar-17.31) 16 Providing & fixing float glass panes :(5.00 mm thick glass panes ) wright not lessthen 12.50 kg/sqm dar - 9.7.7.2) 17 Provding and fixing ISI marked flush door shutters conforming to IS : 2202 (part-1) non- decorative type, core of block board contruction with frame of 1st class hard wood and well matched commercial 3 ply veneers on both faces of shutter :35 mm thick including isi marked stainless steel butt hinges with necessary (9.21.1) 18 Fly proof stainless steel grade 304 wire gauge with 0.50 mm dia wire and 1.4 mm wide aperture with matching wood beading (9.7.8) 19 Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screwswith ISI marked M.S. pressed butt hinges bright finished of required size 9.27.2.1 20 Providingandfixing600x120x5mmglassshelfwithedgesroundoff, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.DSR NO-17.33 21 Providingandfixingwhitevitreouschinapedestaltypewatercloset (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushingcistern,includingflushpipe,withmanuallycontrolleddevice (handlelever),conformingtoIS:7231,withallfittingsandfixtures complete, including cutting and making good the walls and floors wherever required : DAR NO-17.2.2 22 Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting offittingsandbrackets,cuttingandmakinggoodthewallswherever required:-White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer DAR No- 17.7.A 23 Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubberplug,40mmC.P.brasswastecomplete,includingpaintingthe fittings and brackets, cutting and making good the walls wherever required: White glazed fire clay kitchen sink of size 600x450x 250 mm DAR NO:17.9.1 24 Providing and fixing stainless steel A ISI 304 (18/8) kitchen sink as per IS :13983 with c.i brackets and stainless steel plug 40 mm including painting of fitting and brackets , cutting and making good the walls wherever requried (kitchen sink with drain board )(510x1040 mm bowl depth 250mm)(dar-17.10.1.1) 25 Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.20 mm nominal bore, 120 mm long, weighing not less than 198 gms DSR NO-18.62.2 26 Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.15 mm nominal dia DAR NO-1722 B 27 Providing and fixing brass curtain rods ofwall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete. 25 mm diameter.DAR NO-14.28.2 28 Providing and placing on terrace (at all floor levels )polyethlene water storage tank . IS:12701 marked , with cover and suitable locking arrangement and making necessary holes or inlet , outlet and overflow pipes but without fitings and the base support for tank (Dar-18.48) 29 Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.DAR NO-17.22A 30 Providing and layeing in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level:1:5:10 (1 cement :5 coasre sand ( Zone-III) :10 graded stone aggregate 40 mm nominal size dar-4.1.10 31 ProvidingandlayingfactorymadechamferededgeCementConcrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory methodusingPUmould,laidinrequiredcolour&patternover50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60 mm thick C.C. paver block of M-35 grade with approved DAR NO-16.91.1

BRR:7506722 Tender For Ward 7 Kothakulam Awc No 39 Anganwadi Construction E-Tender For Ward 7 Kothakulam Awc No 39 Anganwadi Construction , Materials , Stone Aggregate(Single Size) : 40Mm Nominal Size , Stone Aggregate(Single Size) : 20Mm Nominal Size , Coarse Sand (Zone Iii) , Portland Cement , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With Hopper , Vibrator (Needle Type 40 Mm) , Sundries , Stone For Masonry Work , Through And Bond Stone Size 24*24*39 Cm , Structural Steel Such As Tees, Angles Channels And R.S Joists , Red Oxide Zinc Chromate Primer , Adjustable Telescopic Prop 3 M (2.02 - 3.75 M) , Beam Clamp 300 - 380 Mm (450 - 1070 Mm) , Second Class Kail Wood In Planks , Second Class Kail Wood In Scantling , Hollock Ballies 125 Mm Diametre , Adjustable Pan Eso + Si (2.35 - 3.40) , Stone Aggregate (Single Size) : 10 Mm Nominal Size , Twisted Steel / Deformed Bars , Solid Blocks Of Size 30*20*20 Cm , Solid Blocks Of Size 30*20*15 Cm , Fine Sand (Zone Iv) , 35 Mm Thick Factory Made Solid Panel Pvc Door Shulter Of Single Piece Extruded Profile Non Decorative Finished (Matt Finished) , Powdercoated M.S Butt Hinges 100 Mm * 58 Mm * 1.9 Mm , Bright Finished Or Blackenameled Miled Steel Screws 40 Mm , Bright Finished Or Blackenameled Miled Steel Screws 20 Mm , Vitrified Floor Tile 60* 60 Cm , Ceramic Glazed Tiles Ist Quality 300*300 Mm In All Shades And Designs Of White, Ivory, Grey, Fume Red, Brown Etc , Ceramic Glazed Tiles Ist Quality Minimum Thickness 5 Mm In All Colours Shades And Designs Except Burgundy, Bottle Green Black , Water Thinnable Cement Primer For Interior Wall Surface, Having Voc Content Lessthan 50 Gms/Litre , Plastic Emulsion Paint , Synthetic Enamel Paint In Black Or Chocolate Shade , Anjili Wood Scantls , Pincoda Wood Scantls , Bright Finished Or Black Enameled Mild Steel Butt Hinges 100*58*1.90 Mm , Bright Finished Or Black Enameled Mild Steel Butt Hinges 50*37*1.50 Mm , Anjili Wood Planks , Hollock Wood In Planks , Kiln Seasoning Of Timber , Float Glass Sheet Of Nominal Thickness 4 Mm (Weight Not Lessthan 10 Kg/Sqm) , Mild Steel Round Bar Above 12 Mm Dia , Flats Up To 10 Mm In Thickness , Rawl Plug 50 Mm (Designation 10 Nos) , 200 Mm Aluminium Aldrop , Iron Hooks And Eyes 100 Mm , Anodised Aluminium Handles 125 Mm With Plate 175* 32 Mm , Chromium Plated Brass Screws 25 Mm , Vitreous China Flat Back Wash Basin 550*400 Mm , 15 Mm C.P Brass Tap , C.P Brass Waste 32 Mm , C.I Bracket For Wash Basin And Sinks , Stainless Steel Kitchen Sink - Without Drain Board 470*420 Mm Bowl Depth 178 Mm , Vitreous China Orisa Type Wc Pan Size 580 Mm , Flushing Cistern Pvc 10 Lts Capacity (Low Level) (White) (With Fittings, Accessories And Flush Pipe ) , 100 Mm Sci Trap With Vent Heel , Ptmt - Towel Rail (600 Mm) , Second Class Teak Wood In Scantling , Brass Bib - Cock - 15 Mm Dia , Polyethylene Water Storage Tank With Cover And Suitable Locking Arrangements , Pvc Pipe 110 Mm Outer Dia 6 Kgf/Sq.Cm , Pvc Reducer 110*75 Mm Dia , Pvc Tee 110*110*110 Mm Dia , Pvc Elbow 110 Mm Dia , Pvc Door Elbow 110 Mm Dia , Pvc Bend 110 Mm Dia , Pvc Reducer 75*63 Mm Dia , Pvc Vent Cowl 63 Mm Dia , Pvc Pipe 50 Mm Outer Dia 6 Kgf/Sq.Cm , Pvc Pipe 25 Mm Outer Dia 10 Kgf/Sq.Cm , Stone Aggregate (Single Size : 06Mm Nominal Size) , Interlocking Cc Paver Block (60 Mm Thick, M - 30)

BRR:7506688 Tender For supply of material - , Quarry Waste , Interlocking C.C. Paver Block (80 Mm Thick, M-30) , Stone Aggregate(Single Size): 06 Mm Nominal Size , Stone Aggregate(Single Size):20 Mm Nominal Size , Stone Aggregate(Single Size): 10 Mm Nominal Size , Coarse Sand (Zone Iii) , Portland Cement , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With Hopper , Vibrator (Needle Type 40 Mm) , Sundries

BRR:7506681 , Quarry Waste , Interlocking C.C. Paver Block (80 Mm Thick, M-30) , Stone Aggregate(Single Size): 06 Mm Nominal Size , Stone Aggregate(Single Size):20 Mm Nominal Size , Stone Aggregate(Single Size): 10 Mm Nominal Size , Coarse Sand (Zone Iii) , Portland Cement , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With Hopper , Vibrator (Needle Type 40 Mm) , Sundries

BRR:7506680 , Stone Aggregate (Single Size): 40Mm Nominal Size , Stone Aggregate (Single Size): 20Mm Nominal Size , Coarse Sand (Zone Iii) , Portland Cement , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With Hopper , Vibrator (Needle Type 40 Mm) , Sundries , Stone Aggregate (Single Size): 10Mm Normal Size , Wall Form Panel 1250*500Mm , Corner Angle 45*45*5 Mm 1.5 M Long , 100Mm Channel Shoulder 2.5M Long , Double Clip (Bridge Clip) , Single Clip , M S Tube 40Mm Dia , Smooth Wheeled Roller 8 To 10 Tonne , Water Tanker 5 To 6 Kl Capacity , Water , Well Graded Material For Sub Base Grading I, 53Mm To 9.5 Mm , Well Graded Material For Sub Base Grading I, 9.5Mm To 2.36Mm , Well Graded Material For Sub Base Grading I, 2.36Mm Below @30% , Interlocking C.C Paver Blocks(80Mm Thick, M-30) , Stone Aggregate (Single Size): 06Mm Nominal Size

BRR:7506679 Tender For supply of material for Kariyeli Road Katta Virikkal Ward 10 , Quarry Waste , Interlocking C.C. Paver Block (80 Mm Thick, M-30) , Stone Aggregate(Single Size): 06 Mm Nominal Size , Stone Aggregate(Single Size):20 Mm Nominal Size , Stone Aggregate(Single Size): 10 Mm Nominal Size , Coarse Sand (Zone Iii) , Portland Cement , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With Hopper , Vibrator (Needle Type 40 Mm) , Sundries

BRR:7506677 Tender For Athyora Chayimmal Road Concrete Ward 1 Road Concrete , Road Concrete , Quarry Waste , Stone Aggregate 20 Mm Nominal Size , Stone Aggregate 10 Mm Nominal Size , Coarse Sand , Portland Cement , Concrete Mixer Machine , Vibrater , Sundries

BRR:7506174 Supply And Installation Of Gym Equipment In H.N.B Stadium-1 Hydraulic Excavator 1.5 Cum 2 JCB break hoe Loader 3 Dumpers 15 T capacity 4 Bulldozers 90HP 5 Roller Compactor 1 T 6 Concrete Batching and Mixing Plant 30Cum/hr 7 Tower Crane of 80 m boom with Pouring Bucket 1.5 Cum 8 Concrete Pump 25 cum 9 Vibratory needle Type 10 Transit Mixer 3 cum

BRR:7505872 Tender For Annual Maintenance Work Of Non-Residential Buildings. - Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar As per DSR-2023 Sl. 15.7.4 2 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles above 25 mm and up to 40 mm As per DSR-2023 Sl. 15.23.2 3 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. As per DSR-2023 Sl. 15.56 4 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. As per DSR-2023 Sl. 15.60 5 Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources). As per DSR-2023 Sl. 4.11 6 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).As per DSR-2023 Sl. 4.1.8 7 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) As per DSR-2023 Sl. 5.2.2 8 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Mild steel and Medium Tensile steel bars As per DSR-2023 Sl. 5.22A.1 9 Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts As per DSR-2023 Sl. 5.9.6 10 Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) : With F.P.S.(non modular) bricks. As per DSR-2023 Sl. 6.3.1 11 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand) As per DSR-2023 Sl. 6.4.1 12 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) As per DSR-2023 Sl. 6.13.2 13 Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinalpartitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finishedsmooth. Granite Stone of approved shade As per DSR-2023 Sl. 8.10.2 14 Providing and fixing in wall lining flat pressed three layer (medium density) particle board or graded wood Pre-laminated one side decorative lamination and other side balancing lamination Grade I, Type II, IS : 12823 marked, including priming coat on unexposed arrangement andscrews etc. complete :12 mm thick As per DSR-2023 Sl. 8.26.1 15 Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with : Decorative veneer facings of approved manufacture As per DSR-2023 Sl. 8.28.1 16 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. As per DSR-2023 Sl. 9.20.1 17 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes. As per DSR-2023 Sl. 10.16.1 18 Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15 x 3 mm and nuts & bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides. As per DSR-2023 Sl. 10.29.2 19 Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. As per DSR-2023 Sl. 10.31 20 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate As per DSR-2023 Sl. 11.3.1 21 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make in all colours & shade in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm As per DSR-2023 Sl. 11.46.2 22 Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08%and conforming to IS: 15622, of approved brand & manufacturer in all colours and shade in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints(Payment for grouting of joints to be made separately). Size of Tile 600x600 mm As per DSR-2023 Sl. 11.47.2 23 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gm/ m* As per DSR-2023 Sl. 12.1.3 24 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter As per DSR-2023 Sl. 12.41.2 25 12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand) As per DSR-2023 Sl. 13.1.1 26 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre As per DSR-2023 Sl. 13.41.1 27 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm. over and including one coat of Special primer applied @ 0.75 ltr / 10sqm As per DSR-2023 Sl. 13.48.1 28 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. As per DSR-2023 Sl. 13.62.1 29 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. As per DSR-2023 Sl. 13.80 30 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete As per DSR-2023 Sl. 13.88 31 Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.As per DSR-2023 Sl. 13.91 32 Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm). As per DSR-2023 Sl. 14.5.1 33 Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. As per DSR-2023 Sl. 14.85 34 Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturers specifications & direction of Engineer in-Charge. 80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern. 80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern. As per DSR-2023 Sl. 16.91.2 35 Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests As per DSR-2023 Sl. 17.1.1 36 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid As per DSR-2023 Sl. 17.3.1 37 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps As per DSR-2023 Sl. 17.7.1 38 Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White As per DSR-2023 Sl. 17.18.1 39 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. As per DSR-2023 Sl. 17.31 40 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. As per DSR-2023 Sl. 17.73.2 41 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall. 15 mm dia. nominal bore As per DSR-2023 Sl. 18.10.1 42 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall. 20 mm dia. nominal bore As per DSR-2023 Sl. 18.10.2 43 Providing and fixing brass bib cock of approved quality : 15 mm nominal bore As per DSR-2023 Sl. 18.15.1 44 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal bore As per DSR-2023 Sl. 18.17.1A 45 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. As per DSR-2023 Sl. 18.48 46 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) As per DSR-2023 Sl. 21.3.2 47 Providing and fixing hard drawn steel wire fabric of size 75 x25 mm mesh or other suitable size wire mesh to be fixed & firmly anchored to the concrete surface by means of L shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tool & plants as approved by Engineer-in-charge. As per DSR-2023 Sl. 26.40

BRR:7505870 Tender For Annual Maintenance Of Inspection House Buildings. - Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar As per DSR-2023 Sl. 15.7.4 2 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles above 25 mm and up to 40 mm As per DSR-2023 Sl. 15.23.2 3 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. As per DSR-2023 Sl. 15.56 4 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. As per DSR-2023 Sl. 15.60 5 Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources). As per DSR-2023 Sl. 4.11 6 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).As per DSR-2023 Sl. 4.1.8 7 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) As per DSR-2023 Sl. 5.2.2 8 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Mild steel and Medium Tensile steel bars As per DSR-2023 Sl. 5.22A.1 9 Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts As per DSR-2023 Sl. 5.9.6 10 Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) : With F.P.S.(non modular) bricks. As per DSR-2023 Sl. 6.3.1 11 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand) As per DSR-2023 Sl. 6.4.1 12 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) As per DSR-2023 Sl. 6.13.2 13 Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinalpartitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finishedsmooth. Granite Stone of approved shade As per DSR-2023 Sl. 8.10.2 14 Providing and fixing in wall lining flat pressed three layer (medium density) particle board or graded wood Pre-laminated one side decorative lamination and other side balancing lamination Grade I, Type II, IS : 12823 marked, including priming coat on unexposed arrangement andscrews etc. complete :12 mm thick As per DSR-2023 Sl. 8.26.1 15 Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with : Decorative veneer facings of approved manufacture As per DSR-2023 Sl. 8.28.1 16 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. As per DSR-2023 Sl. 9.20.1 17 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes. As per DSR-2023 Sl. 10.16.1 18 Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15 x 3 mm and nuts & bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides. As per DSR-2023 Sl. 10.29.2 19 Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. As per DSR-2023 Sl. 10.31 20 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate As per DSR-2023 Sl. 11.3.1 21 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make in all colours & shade in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm As per DSR-2023 Sl. 11.46.2 22 Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08%and conforming to IS: 15622, of approved brand & manufacturer in all colours and shade in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints(Payment for grouting of joints to be made separately). Size of Tile 600x600 mm As per DSR-2023 Sl. 11.47.2 23 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gm/ m* As per DSR-2023 Sl. 12.1.3 24 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter As per DSR-2023 Sl. 12.41.2 25 12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand) As per DSR-2023 Sl. 13.1.1 26 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre As per DSR-2023 Sl. 13.41.1 27 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm. over and including one coat of Special primer applied @ 0.75 ltr / 10sqm As per DSR-2023 Sl. 13.48.1 28 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. As per DSR-2023 Sl. 13.62.1 29 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. As per DSR-2023 Sl. 13.80 30 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete As per DSR-2023 Sl. 13.88 31 Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.As per DSR-2023 Sl. 13.91 32 Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm). As per DSR-2023 Sl. 14.5.1 33 Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. As per DSR-2023 Sl. 14.85 34 Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturers specifications & direction of Engineer in-Charge. 80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern. 80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern. As per DSR-2023 Sl. 16.91.2 35 Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests As per DSR-2023 Sl. 17.1.1 36 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid As per DSR-2023 Sl. 17.3.1 37 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps As per DSR-2023 Sl. 17.7.1 38 Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White As per DSR-2023 Sl. 17.18.1 39 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. As per DSR-2023 Sl. 17.31 40 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. As per DSR-2023 Sl. 17.73.2 41 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall. 15 mm dia. nominal bore As per DSR-2023 Sl. 18.10.1 42 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall. 20 mm dia. nominal bore As per DSR-2023 Sl. 18.10.2 43 Providing and fixing brass bib cock of approved quality : 15 mm nominal bore As per DSR-2023 Sl. 18.15.1 44 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal bore As per DSR-2023 Sl. 18.17.1A 45 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. As per DSR-2023 Sl. 18.48 46 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) As per DSR-2023 Sl. 21.3.2 47 Providing and fixing hard drawn steel wire fabric of size 75 x25 mm mesh or other suitable size wire mesh to be fixed & firmly anchored to the concrete surface by means of L shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tool & plants as approved by Engineer-in-charge. As per DSR-2023 Sl. 26.40

BRR:7505799 Tender For Construction Work Of A Room And Toilet In Collectorate Premises, Baghpat - Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. DSR 2023 SI. No. 2.6.1 2 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)DSR 2023 SI. No. 4.1.8 3 CC 1:2:4 (1 cement: 2 coarse sand (zone-III) derived from 5.1.3 natural sources: 4 graded stone aggregate 20 mm nominal size derived from natural sources).DSR 2023 SI. No- 5.1.3 4 Brick work with common burnt clay F.P.S. (non modular) bricks of classdesignation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) DSR 2023 SI. No- 6.1.1 5 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand). DSR 2023 SI. No. 6.4.1 6 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). DSR 2023 SI. No. 5.2.2 7 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from naturalources).DSR 2023 SI. No. 5.3 8 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Mild steel and Medium Tensile steel bars. DSR 2023 SI. No- 5.22.1 9 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth,sides of foundation etc. complete. DSR 2023 SI. No. 2.25(a) 10 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Double charge vitrified tile polished finish of size of Tile 600x600mm. All Material, Labour, T&P etc also including labour cess and all other applicable Taxes (But excluding GST) required for proper completion of work as per direction of Engineer-in-charge. DSR 2023 SI. No- 11.41A1.1 11 12 mm cement plaster finished with a floating coat of neat cement of mix.1:4 (1 cement: 4 coarse sand). DSR 2023 SI. No- 13.4.1 12 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. DSR 2023 SI. No- 10.25.2 13 Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part 1) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 pły veneering with verticall grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. DSR 2023. 9.21.2 14 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS. 733 and IS. 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, ie. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/panelling, C.P brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge (Glazing, paneling and dash fasteners to be paid for separately). Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). DSR 2023. SI. No. 21.1.1 15 Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides. DSR 2023 SI.No. 10.29.1 16 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item) With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)2023 SI. No-21.3.1 17 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 2023 SI. No- 13.80 18 Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre. DSR 2023 SI.No 13.85.3 19 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. two coat. DSR 2023 SI.No.- 13.82.2 20 Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 Itr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm). DSR 2023. SI.No.13.46.1 21 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: DSR 2023. SI.No. 13.99.1 22 Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishingthe surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm. DSR 2023Item No- 22.7.1 23 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15 mm nominal bore. DSR 2023 SI.No- 18.53.1 24 Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore. DSR 2023 SI.No- 18.50.1 25 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid. DSR 2023. SI.No 17.3.1 26 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap. DSR 2023 SI.No- 17.7.2 Flat back wash basin of size 550x400mm 27 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.. DSR 2023. SI.No- 18.48 28 Providing and fixing uplasticised PVC connection pipe with brass unions. All Material, Labour, T&P etc also including labour cess and all other applicable Taxes (But excluding GST) required for proper completion of work as per direction of Engineer-in-charge. 45 cm length. 20mm nominal bore. DSR 2023 SI. No- 18.21.1.2 29 Providing and fixing ball valve brass of approved quality, high or low pressure, with plastic floats complete 20 mm nominal boreDSR 2023 SI. No- 18.18..2 30 Providing and fixingbrass bib cock of approved quality,20 mm nominal boreDSR 2023 SI. No- 18.15.1 31 Providing and fixingP.V.C. waste pipe for sink or wash basin including PVC waste fittings completeof approved quality,20 mm nominal boreDSR 2023 SI. No- 17. 28. 2 . 2 32 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 20mm Nominal Dia pipe. DSR 2023. SI.No- 18.9.2 33 Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS: 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required: Single half stall urinal with 5 litre P.V.C. automatic flushing cistern. DSR 2023 SI.No 17.5.1 34 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. DSR 2023. SI.No. 1607.95 35 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms. DSR 2023 SI.No. 17.73.1 36 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion. 110 mm Dia.All Material, Labour, T&P etc also including labour cess and all other applicable Taxes (But excluding GST) required for proper completion of work as per direction of Engineer-in-charge. DSR 2023 SI. No- 12.41.2 37 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface I recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. As per DSR E&M Ser No1.10.2 Group B 38 Wiring forcircuit/submain wiringalongwithearthwire withthe following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq.mm + 1 X 2.5 sqmm earth wireAs per DSR E&M Ser No 1.14.2 39 Wiring forcircuit/submain wiringalongwithearthwire withthe following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 4. sq.mm + 1 X 4 sqmm earth wireAs per DSR E&M Ser No1.14.3 40 Supplyingandfixing two modulesteppedtypeelectronicfan regulatorontheexistingmodularplateswitchboxincluding connections but excluding modular plate etc. as required. As per DSR E&M Ser No 1.25 41 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3pin5/6Amodularsocketoutletand5/6Amodularswitch, connections etc. as required. As per DSR E&M Ser No 1.31 42 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch. connections etc. as required. As per DSR E&M Ser No 1.32 43 Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providingand fixing 25 A modular socketoutletand25 AmodularSPMCB, C curveincluding connections, paintingetc. as required.As per DSR E&M Ser No 1.57 44 Supply, Installation, Testing and Commissioning of 1200 mm sweep,BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts,washers, temperature rise=75 degree C (max.), sulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. DSR 19.1 45 S/F Information /sign board i/c all comp. 46 GST

BRR:7505795 Tender For Cc Road Construction Work.; 1 Excavation of foundation in ordinary soil (loam clay or sand) including lift upto 1.50 meter and lead upto 30 meter and including filling, watering and ramming of excavated earth into the trenches or into the space between the building and sides of foundation trenches or into the plinth and removal and disposal of sur-plus earth as directed by the Engineer incharge up to a distance of 30 meters from the foundation trenches. 2 Providing and laying in cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size) and curing complete, including cost of form- work in foundation and floors. 3 Coursed rubble massonary (second sort) with hard stone in foundation & plinth with : cement mortor 1:6 (1 cement:6 course sand) DSR 7.7.1 4 Construction of granular sub-base by providingready mix material spreading in uniform layers with motor grader on prepared surfaceand compacted with 80-100 KN Smooth wheel static rollar to achieve the desired density at OMCcomplete as per Technical specification Clause 401. (GSB) 5 Providing, laying, spreading and compacting stone aggregates of 53mm to 22.4mm sizes (Crusher broken) to water bound macadam (WBM III) specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405.(WBM III) 6 Cement Concrete Pavement: Construction of un-reinforceced , expansion and consruction joint only, plain cement concrete pavement, thickness as per design ,over a prepaired sub base withh 43 grade cement or any other type as per clouse 1501 .2.2. M-30 grade corse and fine aggregates confirming to IS:383 maximum size of coarse aggregates not exeding 25 mm mixed in a concrete mixer of not less than 0.20 cum. capacity and apropreate weigh batcher using approoved mix design laid in a approoved fixed site form work (steel chanel ) laying and fixing of 125 micron thick polythene film wedges steel plates including levelling the form work as per drawing ,speading the concrete with shovels rackes, compacted usingplate vibrators and finished in continuous oparation including provision of contraction and expansion ,construction jointes,primer,sealant , near aproches to bridge /culvert and construction joints admixtures as approoved curing of concrete slab for 14 days.using curing compounds(where specified ) and water finishing to lines and grade as per drawing and technical specification clause 1501. 7 Raised and cut pointing on stone work with cement mortor 1:3 (1 cement : 3 fine sand): DSR 13.33.2 8 Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) complete.20 mm nominal size stone aggregate 9 Filling available executed earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exeeding 20cm in depth, consolidation each deposited layer by ramming and watering, lead up to 50m and lift up to 1.50m. 10 Supply and fixing of Sheela Patta or sign board 11 AFTER DEDUCTION COMPETITIVE PRICE EFFICENTY (5%) 12 ( Rates in BOQ are exclusive of G.S.T. Amount )

BRR:7505794 Tender For Block - Construction Of Cc Road From Main Marg To Primary Health Center Kachnarava And Construction Of Boundary Wall - Excavation of foundation in ordinary soil (loam clay or sand) including lift upto 1.50 meter and lead upto 30 meter and including filling, watering and ramming of excavated earth into the trenches or into the space between the building and sides of foundation trenches or into the plinth and removal and disposal of sur-plus earth as directed by the Engineer incharge up to a distance of 30 meters from the foundation trenches. 2 Providing and laying in cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size) and curing complete, including cost of form- work in foundation and floors. 3 Coursed rubble massonary (second sort) with hard stone in foundation & plinth with : cement mortor 1:6 (1 cement:6 course sand) DSR 7.7.1 4 Construction of granular sub-base by providingready mix material spreading in uniform layers with motor grader on prepared surfaceand compacted with 80-100 KN Smooth wheel static rollar to achieve the desired density at OMCcomplete as per Technical specification Clause 401. (GSB) 5 Providing, laying, spreading and compacting stone aggregates of 53mm to 22.4mm sizes (Crusher broken) to water bound macadam (WBM III) specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405.(WBM III) 6 Cement Concrete Pavement: Construction of un-reinforceced , expansion and consruction joint only, plain cement concrete pavement, thickness as per design ,over a prepaired sub base withh 43 grade cement or any other type as per clouse 1501 .2.2. M-30 grade corse and fine aggregates confirming to IS:383 maximum size of coarse aggregates not exeding 25 mm mixed in a concrete mixer of not less than 0.20 cum. capacity and apropreate weigh batcher using approoved mix design laid in a approoved fixed site form work (steel chanel ) laying and fixing of 125 micron thick polythene film wedges steel plates including levelling the form work as per drawing ,speading the concrete with shovels rackes, compacted usingplate vibrators and finished in continuous oparation including provision of contraction and expansion ,construction jointes,primer,sealant , near aproches to bridge /culvert and construction joints admixtures as approoved curing of concrete slab for 14 days.using curing compounds(where specified ) and water finishing to lines and grade as per drawing and technical specification clause 1501. 7 Clearing jungle I/c uprooting rand, grass, wood trees etc. I/c removal of rubbish up to a distance of 50m as per DSR-2.31 8 Excavation of foundation in ordinary soil (loam clay or sand) including lift upto 1.50 meter and lead upto 30 meter and including filling, watering and ramming of excavated earth into the trenches or into the space between the building and sides of foundation trenches or into the plinth and removal and disposal of sur-plus earth as directed by the Engineer incharge up to a distance of 30 meters from the foundation trenches. 9 Providing and laying in cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size) and curing complete, including cost of form- work in foundation and floors. 10 Coursed rubble massonary (second sort) with hard stone in foundation & plinth with : cement mortor 1:6 (1 cement:6 course sand) DSR 7.7.1 11 R.C.C. work with approved coarse sand and 20mm gauge approved stone grit inthe foundation and footing & beams (Using 1:1.5:3 Mix concrete) strength of the concrete shall not be less than M-20. Upto plinth level 12 As in item above but in R.C.C. columns (Using1:1.5:3Mix concrete) having strength not less than M-20. Above plinth level 13 M-150 brick work in 1:6 (one cement and six coarse sand of 2.25 fineness modulus) mortar in super-structure above plinth level up to floor two level ( up to two storeys ) includingnecessarycutting and moulding of brick work asrequiredand also including honeycombed brick work in thickness of wall more than 12cms. (1:6 cement : coarse sand) 14 P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. 15 15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand) 16 12 mm cement plaster in single coat on inner side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. (1) 1 cement : 6 course sand of 2.25 F.M. 17 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade. New work (Two or more coats applied @ 1.43 ltr/ 10 sqm. over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm). 18 Lintels, beams, plinth beams, girders, bressumers and cantilevers. 19 Columns,Pillars, Piers, Abutments, Posts and Struts. 20 Mild steel or iron work of small sizes and sections such as holding down bolts, hold fast tierods,gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. 21 Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift. 22 S/f of sign board i.e all complete 23 AFTER DEDUCTION COMPETITIVE PRICE EFFICENTY (5%) 24 ( Rates in BOQ are exclusive of G.S.T. Amount )

BRR:7505767 Electronic Weighing Machine For Various Anganwadies , Specification Of Weighing Machine For Various Anganwadies , 1)Platform Weighing Scale,Mechanical, Capacity Minimum 125 Kg 2)Legal Metrology Sealed

BRR:7505489 Special Repairs To Bldg No P 24 Of Asc Centre And College Under Ge Central Bangalore-- 1 Taking down cement plaster of any description including racking out joints, hacking for key scrubbing down with water etcandremoval of entire debris as ordered outside MD land complete all as directed. 2 Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thick above or below ground level and removalof entire debris as ordered outside MD land complete all as directed. 3 Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chaj-jas and similar sus-pended work (reinforcement cut as required to facilitate demolition)including removing of debris as ordered outside MD land complete all as directed. 4 Demolition of brickwork , block masonryor stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc and removal of debris as ordered outside MD land complete all as directed. 5 Dismantling structural steel work incl gates, doors but excluding framed truss etc complete all as directed. 6 Dismantling of plain or corrugated steel sheeting any gauge thickness incl Nanital or similar pattern as in roof coverings and stacking at site where directed . 7 Dismantling floor, hearth or wall tiling inluding cement mortar bedding (but not backing), stackingserviceable tiles at site andremoval of entire debris as ordered outside MD land complete all as directed. 8 Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from frame) and stacking at site where directed. 9 All as per item 8here-in-above but exceeding 1.5 Sqm but not exceeding 4 Sqm each 10 Excavation in trenches and not exe. 1.5 m wide and not exe. 1.5 m in depth for foundation of drain, man hole , laying of UG cablesetc. not exe. 10 Sq. m on plan and not exe. 1.5 m depth and getting out in soft / loosesoil complete all as specified and directed. 11 Returning filling in trenches including spreading, leveling,watering and well ramming in layers not exceeding 25 cm thick in soft rock complete all as specified and directed 12 Removing excavated surplus soil to a distance not exceeding 50 mtsand depositing where directed .at a level not exceeding1.5 M above the starting point complete all as directed. 13 M & L for Hard core of broken hard stone or boulders of guage not exceeding 63 mm , deposited spread as subbase to inter locking tilesin layers n.exc 15cm thick , watered & well rammedto true surface complete all as specified and directed. 14 M&L factory made pre cast PCC 1:3:6, type C1 (using 20 mm graded granite aggregate) as in block masonry with solid blocks, exceeding 10 cm in width and setting in CM 1:4 complete all as specified. 15 All sameas per itemNo 14 here-in-above but solid blocks not exceeding 10 cm thick -do- 16 Providing precast ce- ment concrete Type B1 1:2 :4 using 20 mm graded crushed stone aggregate in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry),string courses, copings. kneelers, apex stones, pier caps, columns, posts , boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets,etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to match Set in cement mortar 1:4 completeall as directed. 17 M&L for precast RCC 1:2:4type B1 using 20mm graded crushed stone aggregate as in landings, cover slabs (for man holes, drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including placing in position and set in CM (1:6) complete all as specified & as directed 18 Supply onlyIntegral Water Proofing Compound (ISI Marked) of Make : CICO,Acco Proof, Impermo, Aqua flex as approved. 19 Cutting holes of size Exc. half brick but not exc. one brick in brick walls in brick walls built in cement mortar or cement lime mortar and stone walls built in lime mortarfor insertingholdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 TypeB-1 as required including making good as per its original specification with out any extra costcomplete all as directed. 20 Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 as required including making good as per its original specification with out any extra costcomplete all as directed. 21 S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour single piece extruded PVC profile reinforced with MS square tube in opening as per specifications completeall as directed. 22 S&F factory made pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, mild steel sheet of 1.25 mm thickness includingfillingthe hollow section of steelframe withPCC 1:2;4 typeBo using 12.5 mm graded crushed stoneaggregrate tothe entire hollow section tothe satisfaction ofEngineer-in-charge , complete as specified & as directed. 23 S&F Second class hard wood factory made kiln - seasoned, plain, solid, straight chowkats and frames , wrought, framed, rebated on the solid, rounded or chamfered , put togetherwith glue, pinned at joints and fixed in position complete all as directed. 24 S &F35 mm thick second class hard wood factory made glazed and skeleton shutter open rebated and prepared to receive glass, guage etc edge of framing plain chamfered or rounded fitted with cut and mitred beads for securing guage etc size of members of shutter as specified in SSR Part I Section 8 clause 8.24 (a) supplied and fitted to chowkats. 25 S&F 30 mm thick Flush shutters, solid core construction, with block coard core & plywood face panels commercial type on both side conforming to IS 2202 (Part- I) -1999, including internal liping beading all round fixed as in Door Shutter,Cup board shutter & Kitchen rack allas specified. 26 S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement. 27 S&F 19mm thick MDF Board both side finished as in wardrobe no of compartments & Drawersallas specified and as directed by Engineer-in-Charge. 28 S&F Powder coated aluminium sliding window (three way) frame & shutter with glazed shutter and without miremesh shutter /skeleton section with & including the following:-(i) Aluminium frame section 116x36.50x1.80mm.(ii) Aluminium shutter glazed/skeleton section 50x20x1.50mm thick.(iii) Aluminium grill size 50mmx50mm and 4 to 5mm thick bars complete all as specified.(iv) Fixing arrangements legs in hold fast in walls incl PCC (1:3:6) making goog distributed surfaces complete in originally shape.(v) 4mm thick glass orinary quality and fixed with rubber gasket for with glazed shutter etc.(vi) Stainless steelwire mesh 0.36mm nominal dia avg aperature 1.14mm and fixed with rubber gasket for without glazed shutter etc.(vii) Aluminium disc /bow hanle and locking system complete 29 S&F Powder coated aluminium Ventilator (partially fixed glazing and Partially louvered glazing) with & include the following:-(i) Aluminium frame section 45x25x1.80mm.(ii) Fixing arrangements legs in hold fast in walls incl PCC (1:3:6) making goog distributed surfaces complete in originally shape.(v) 4mm thick frosted glass orinary quality (partially fixed glazing and Partially louvered glazing) and fixed with rubber gasket for with glazed shutter etc. 30 S & F150 mm long aluminium, anodised , barrel tower bolt (ISI marked) of extruded section and fixed. 31 S&F 100mm size butt hinges, medium weight stainless steeland fixed . 32 S&F 100 mm size aluminium alloy handles (ISI Marked) fabricated type anodisedand fixed. 33 S&F300 mm long aluminium alloy, anodised sliding door bolt (ISI Marked) with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed. 34 S&F Mild steel powder coatedbodydoor stopper with hard drawn steel spring, 150mm size fixed to door all as directed. 35 S & F mild steel 300mm ordinary rat rail rod pattern spring including roller and roller plate fixed to door all as directed. 36 S&F continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps 40mm (when open) fixed with CP steel screws complete all as specified and as directed. 37 S&F in repair 25mm dia aluminium anodised decorative type curtain rods. fixed with CP steel screws complete all as specified and as directed. 38 S&F in repair decorative type curtain rod brackets. 39 S&F in Repairs Tubular Towel Rail of 20mm dia of 60cm in length, D shaped, with brass chromium platedbrackets all as specified and directed. 40 Supply onlystainless steelwire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mmand fixed with stainless steel wire staples for steelwindow . 41 S & F 10 mm dia and over TMTbarscut to length bent to shape required cranking including bending , hooking ends etc and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. 42 S&F Mildsteel iron framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fit-tings (exclusive of steel sheeting or other cover-ing, running rails and guides) and hanging; al-so fastening and fixing complete all as directed . Steel conforming to Fe 410 -W (Gde E- 250 QualityA) 43 S&F pre-painted galvalume (zincalume) aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof coverings/cladding to walls fixed with self tapping screws as specified. 44 Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. andbrushing thesamewith neat cement slurry with 3.0 Kg ofcement perSqm completeall asdirected. 45 Material and labourcleaning ofsurface with wire brushes and water removing of unsolvent materials and depositing of the same as directed outside MoD land andprovide 10 mm thick screed bed/ bedding layer in CM 1:3 mixed with Water Proofing Compound (WPC) as per manufacturer instructions, including finishing the surface fair and even on RCC roof/ parapet once bedding layer of concrete is completely dried and apply oil bound bituminous primer @ 0.30 Kg/Sqm and providing 4mm thick APP modified water proofing membrane weighing not less than 4.00 Kg/Sqm reinforced with non woven polyster matt weighing not less than 160 gms/Sqm including minimum 10 cm side over laps and 15 cmend lap torch sealed and bonded as per detailed procedure as directed and finally finished the top surface with two coats of thermal resistant paint complete all as specified and as directed.Note: (i) The quoted rate is deemed to be inclusive cleaningthe entire surfacetosatisfaction ofEnginner-in-charge & removal of debris , 10 mm thick 1:3 screed & complete APP treatment. (ii) WPC will be paid seperately (iii)The work shall be carried out only through manufacturer or their authorised applicator and a written guarantee for work shall be submitted by the manufacturer for the effectiveness of WPT (iv) Care shall be taken to avoid wrinkle and air gaps while sticking membrane to the bitumen applied surface. 46 M&L for 25 mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as inpadding over roof / chajja finished even & smooth without using extra cement complete all as directed. 47 M & L for 25 mm thick plain cement concrete 1:2:4 type Bo using12.5 mm graded crushedstone aggregate as insub base offloor and finished the surface complete all as directed. 48 M & L for 75 mm thick plain cement concrete 1:4:8 type D2 using40mm graded crushedstone aggregate as insub base offloor/ foot path etc and finished the surface complete all as directed. 49 M & L for 75 mm thick plain cement conctere 1: 3 : 6type C2 using 40 mm graded crushedstone aggregateas in plinth protection finished the surface fairand even complete all as directed. 50 M & L non-skid coloured joint freeceramic tiles 7 to 8 mm thick (square/rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all directed and specified. 51 All same as per item No 50here - in - above but each tile exceeding 0.18 Sqm butnotexceeding 0.36Sqm-do- 52 All same as per item No 50here - in - above but as in dado & skirting with10 mm thick 1 : 4 cement mortar screed - do - 53 M&L glazed ceramic coloured tiles of size 350mm x 250mmx 7mm / 450mmx350mmx7mm thick, on verticals surfaces, set and jointed inneat cement slurry including 10 mm thick back coat in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to matchcompleteall directed.(Note for item Nos 50 to 53 : i) Quoted rateis deemed to be inclusive of cement screed. ii) Colour of tiles shall be got appproved before incorporation in the work) 54 M&L for 18-20mm thick Sadherhali stone slab flooring, steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granit laid over andincluding15 mm thick screed bedding in cement mortar 1 : 4includingRounding to edges complete. 55 All same as per item No 74here - in - above but as in dado & skirting with10 mm thick 1 : 3 cement mortar screed - do -(Note for item No 54 & 55 : i) Quoted rateis deemed to be inclusive of cement screed.) 56 M&L M-35 grade, 60 mm thick machine pressed, PVC moulded precast cement concrete interlocking paver blocks any shape and size with grey cement and pigment confirming to IS: 15658-2006, laid over and including 50 mm thick compacted sand cushion complete complete all as specified.(Note ; Quoted rate is deemed tobe inclusive of 50 mm thick compactedsand cushoning). 57 M&L for rendering 15 mm thick in CM 1:6 on brick or concrete surfaces or surface other than fair faces brick work, finished even and smooth without using extra cement complete all as specified. 58 All as per item No 57 here-in-above but 5mm thick in CM 1:3 on ceiling,chajja,roof projection etc. 59 M & L for Dubbing out average 10mm thick on irregular face of stone walls of external surface in CM 1:6complete all as specified and directed. 60 M&L forrendering 15 mm thick in cement mortar 1:4 on fair faces of brick work/ stone work or concrete surfaces mixed with WPC as per manufacturer instruction, and finished the surface fair and even complete all as specified and directed.(Note: WPC shall be measured and paid separately). 61 Racking out joints / points in cement mortar torandom rubble or polygonal rubble uncoursed or brought upto coursesin cementor cement lime mortar completeall asdirected. 62 Three coats of white wash on newly plastered surface of ceiling after necessary preparation of surfacecomplete all as directed. 63 All asper item No. 62 here-in-above buttwocoats on old treated surface ofwalls- do - 64 M&L preparing new plastered wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 3 mm thick white cement based wall care putty as ordered complete all as specified. 65 Complete removalofany type ofexixtingtreatment from wallssurfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 3 mm thick white cement based wall care putty as ordered complete all as specified. 66 Complete removalofany type ofexixtingtreatment from wallssurfaces & applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new or old surfaces complete all as specified. 67 Material & Labour for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint (Apex -Ultima Protek) of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over newsurfaces applied by mechanicalmeans i.e Airless spray including filing undulations with white cement based putty mixed with multi purpose mixer complete all as directed. 68 M & L Two coats of 1st quality synthetic enamel paint over a coat of pink primer on new wooden surface of any description over 10 cm in width or girth including necessary preparation of new wooden surface complete all as directed. 69 M & L Two coats of 1st quality synthetic enemal paint over a coat of zinc chromate primer over any description of new steel surface over 10 cm in width or girth including necessary preparation ofnew steel surface complete all as directed. 70 Taking down old rusted / wornout 25 mm bore GI tubing after necessary disconnection & S&F25 mm boreGI water tubingmedium grade (ISI marked) withfittings such as bends, tees, elbows, nipples, unions, short pieces etc laid in trenches making necessary connection and testing on completionall as specified anddirected.. 71 All sameas per itemNo 70 here-in-above but laid floors / wall / underroad crossing etc -do - 72 S&F40 mm boreGI water tubinglight grade (ISI marked) fixed on pole withsuitable size ofMS clamps , laid on floor etc as cable protection complete all as specified anddirected.. 73 Taking up or down steel tubing for 15mm dia pipe and connections including cleaning for re-fixing or removal to store.all asdirected . 74 Taking up or down steel tubing for 20mm dia pipe and connections including cleaning for re-fixing or removal to store.all as directed. 75 S&F 16 mm outer dia CPVC Pipe (ISI Marked) SDR II & plain CPVC SDR II fittings fixed on wall, celing or floors complete ass as specified. 76 S&F 20mm outer dia CPVC Pipe (ISI Marked) fixed complete to wall, celing or floors including taking up or down 15mm boresteel tubing complete all as specified. 77 S&F in repairs 15 mm bore CPbib tap, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule 78 Supply and fixingin repair Angle valve cast copper alloy cromium Plated (CP)15mm dia screwed down high pressure with crutch or butter fly handles screwed both and iron pipe or forunions and fixed completeall as directed. 79 S&F soap dish, vitreous china, white, approximate size 160x160x90mm fixed to plugs with chromium plated (CP) brass screws 80 Supply and fixingin repair PVC Shower Rose swivel typesuitable for 15mm dial pipe (as per sample approved by Engineer-in-Charge complete all as directed. 81 S&F in repairs PVC connection 600 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified. 82 S&F in repair Gun metalglobe or gate valves with iron wheelhead screwed box and both ends for iron pipe for 25 mm bore of pipe or union complete all as directed 83 S&F in repair Gun metalglobe or gate valves with iron wheelhead screwed box and both ends for iron pipe for 40 mm bore of pipe or union complete all as directed 84 S & F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to wallin repars complete all as directed. 85 S & F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to wallin repars complete all as directed. 86 S&F in repair 75 mm size PVC (SWR) floor trap with grating including jonting the same with solvent cement complete all as directed. 87 S & F75 mmbore size PVC (SWR) bends any radius with access door including jointing the same with solvent cement complete all as directed. 88 S & F110 mmbore size PVC (SWR) bends any radius with access door including jointing the same with solvent cement complete all as directed. 89 S&F110 mmbore size PVC (SWR)junction single(single T)equal or unequal with access doorincluding jointing the same with solvent cement complete all as directed. 90 All as per item No 109here -in -above but 75mm bore. 91 S&F 550 mm X 400 mm size white flat backvitreous china wash hand basin including chromium plated pillar tap cap stain head suitable for 15 mm bore of pipe , PVC connection 15 mm dia 45 cm long with chromium plated nuts and bolts and suitablewashers, PVC waste 32 bore CP waste coupling chain and plug , porcelain stopper including CI bracket fixed in repair complete all as diirected. 92 S&F in repairs 600mm x 450mm looking mirror of selected quality glass not less than 5.5mm thick, mounted on 6mm thick AC building board or commercial plywood including aluminium framing and fixed to PVC rawl plugs with chromium plated brass screws and cup washers complete all as specified. 93 S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, ‘P’ or ‘S’ trap, including connection to trap and flushing pipe, antisyphonage pipe etcincluding provision of PCC (1:5:10) type E2 in filling, making good to floor, complete all as specified 94 S & F in repairs, vitreous China wash down water closet pan (pedestal pattern), white, including connection to outgoing drain and 32mm dia flush pipe,flushing pipe, anti syphonic pipe with and including white PVC seat and cover closed pattern with flat bottom and MS chromium plated hinging device including provision of 10 ltr capacity low levelPVC Flushing cistern, PVC connection pipe, 15 mm dia, 600 mm long complete including making good damaged/disturbed surfaces complete all as specified and directed. Make of Pan CERA Cat No S1053101/S1053102 and of cistern B1010109 or equivelent of Parryware/Hindware/Prayag 95 S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including32 mm dia PVC flush pipeconnected to water closet with inlet, ball valve, float and handle complete all as specified 96 Dismantling of existing any type & any capacity water storage tank fixed in any description and stacking at site andS&F new 1000 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical verticalwith close top) triple layer colour white both inside and outside with top cover including PVC float valve high pressure suitable for 20 mm bore of pipe with polythene float, fixture hoisted and fixed in position where orderedand making necessary connection and testing complete all as directed. 97 M&L for cutting existing GI water main pipe line in position of 40 mm bore and making connection toexisting pipe line of 25mm bore with & including insertion of new GI Tee (ISI marked) of size 40mm x 40mm x 25mm including excavation & earth work in any type of soil complete all as directed. 98 E&M : Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete, (fittings such as switches, ceiling roses, pendants, regulators, sockets etc. to be measured separately), removing taken down materials to a place where ordered for crediting includingmaking good disturbed surfaces of walls, floors, etc to match with the existing surface complete all as directed.. 99 Point wiring with PVC insulated and unsheathed FRLS cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn in and including PVC rigid non metalicconduit (Medium Grade) on Surface conduite conforming to IS-9537 with all accessories including fabricated MS terminal boxes fixed flush with wall surface with 3mm thicklaminated sheet top cover fixed with brass screw for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for :-(a) One light / Fan / bellpoint controlled by one 5 Amps switch one way 100 (d) One light point contrlled by two, two way switchs , single pole 101 (b) One 3 pin socket point 5 Amp on independent board 102 (c) One 3 pin socket point 5 Amp on same board with other switches.(to be provide new point as ordered atsite) 103 All as per item No. 99 here-in-above but with 2.5sqmm ( Nominal area ) cable with 2.5 Sqmm size copper earth continuity conductor for 3 pin 15 A socket outlet on independent board complete all as specified and directed. 104 Supply and fix Switch piano, flush button single pole, 5 Amps one way. 105 Supply and fix Switch piano, flush button single pole, 5 Amps two way. 106 Supply and fix Switch sokcet combination flush type 5 Amp ,2-in-1muliti purpose 107 Supply and fix Switch socket combination flush type 5/16 Amps , 5-in-1universal multipurpose 108 Supply and fix bell push, flush button single pole, 5 Amps one way. 109 Supply and fix bell ding dong, 230 V ACsingle pole,, 5 Amps one way. 110 Ceiling rose surface bakelite 65x50mm three terminals including supply and fix PVC square blocks. 111 Supply and fix Fan regulator electronic, step & socket type 230 volt, suitable for 1200/1400mm sweep ceiling fan. 112 Taking down existinglight fittings fixed in any descriptionand S&F new 10 Watt , 6000K, 230 Volt,2ft Batten surface and wall mounted LED batten with polycarbonate housing with PVChousing & integrated electronic driver complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete fixed as per manufacturers instructions and making necessary electricalconnections and testing on completion complete all as directed. . Make : Havells/wipro/surya/ Philips 113 Taking down existinglight fittings fixed in any descriptionand S&F new 20 Watt , 6000K, 230 Volt,4ft Batten surface and wall mounted LED batten with polycarbonate housing with PVC housing & integrated electronic driver complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete fixed as per manufacturers instructions and making necessary electricalconnections and testing on completion complete all as directed. . Make : Havells/wipro/surya/ Philips 114 S&F bldg security light light fittings 1x 35 Watt Ac 230v out door typeLED street light with high pressuredie cast aluminium and heat ressistent complete with driver ,lamp bracket with impact and corrosion resistentincluding thermal managment in multiple optics complete, IP65/66 and wired with all accessories and including connection up with twine core twisted flexible copper conductor cable with 1.5 M long suitable size all as specified and directed. Make : Crompton Greaves/Bajaj/ Philips 115 S&F steet light bracket made out of 25 mm bore GI Light grade 1.00 M long to required shape as in bracket for steet light fittings fixed with two pair of MS flat iron clamp of size50mm X 6 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flate iron surface with two coates of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. 116 S&Fin repair Sheet metal enclosure (ISI marked) distribution board for 415 volts, TPN 04 way Vertical type, doubledoor, triplepole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed. 117 S&Fin repair Sheet metal enclosure (ISI marked) distribution board for 240 volts, SPN 8 way Vertical type, doubledoor, singlepole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed. 118 S&Fin repair Sheet metal enclosure (ISI marked) distribution board for 240 volts, SPN 4 way Vertical type, doubledoor, singlepole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed. 119 S & Fin repair MCB single pole 6 to 32 Amps 240 volts, 10 kA rupturing capacity providing in DB completeall as specified and directed by Engr-in-charge. 120 S & F in repairMCB single pole & neutral 40 Amps 240 volts, 10 kA rupturing capacity providing in DB completeall as specified. 121 S & F MCCB TP&N 100 Amps 415 volts, C Series 16 kA rupturing capacity providing in DB completeall as specified. 122 Taking down old existing sub main wiring and provide new submain wiring with 2 runs of 4 Sqmm single core PVC insulated, unsheathed, multi strandedcopper conductor and one single core 4 Sqmm PVC insulated , unsheathed , multi strandedcopper cable as earthing lead as per IS : 694 / 1990 drawn through and includingnon-metallic PVC rigid conduit/casing caping of size as orderedin walls / ceilings etc with all accessories such as Tees, Elbows, junction box, reducers etc and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion complete all as specified and directed. (Note :- 2 runs 4 Sqmm cable , one run4 Sqmmcableand one run of PVC Conduit /Casing caping shallbe measured as oneunit length) . 123 Allas per itemNo 122 here-in-above but 2 runs with 6 Sqmm single core cable and 6 Sqmm single core as earth contunity wire -do-. (Note :- 2 runs 6 Sqmm cable , one run6 Sqmmcable and one run of PVC Conduit shallbe measured as oneunit length) 124 M&L for taking down and dismantling of ceiling fan 1200mm/1400mm sweep 230 Volt 50 C/S AC of any make or model by opening the cover, separating down rod, rotor and stator assembly, locating the fault and making the fan fully in serviceable condition with & including replacing the bearing withsimilar type of exisitng one, worn out screws of the cover, split pin, twin core flexible copper wire of size 23/0.0076, locking nuts & machine screws with spring washer for ceiling fan blades, oiling and greasing including rewinding of ceiling fan by removing of burnt winding from stator and rewinding the same with super enamelled copper winding wire of same gauge, same weight & turns including varnishing of winding etc &finally painting the ceiling fan with one coat of spray painting with white DUCO Paint & lettering & Numbering the same as per existing ,reassembling , refixingthe same in same or different location asordered & finallytesting the fan ,complete all as directed.Note : (i) Spare Parts/accessories found unserviceable includingbearings , rewinding etc which are required to makethe fan functional shall be providsed by thecontractorwithout any extra cost toGovt as quoted rate isdeemed tobe inclusive forthesame .(ii) Quoted rate isdeemed tobe inclusive ofpainting . 125 Supply & fixing and testing exhaust fan of 200mm sweep heavy duty, double ball bearing, 1400 RPM, PVCbody , suitable for SP 230 / 250 volt, 50 Hz AC supply complete with louver shutter including fixing / grouting of frame in any type of masonry wall tosize by corecutting using core cutting machine& connecting with & including 3 Nos 1.5 sqmm single core, PVC insulated but unsheathed FRLS 1100 volts grade cable with multi-stranded copper conductor from ceiling rose to fanfinally making good the disturbued surface ofwalls both internal& externaltoits originalspecifications tothe satisfaction ofEnginner-in-charge complete all as directed. Make : Bajaj/ CG / Orient / Usha as approved (Note: Quoted rate isdeemed tobe inclusive ofcore cutting towall , including finishing the wall surface toits originalspecifications) 126 S&F in repair of sheet metal enclosure of size 1500 x 1000 x 300 mm grouted on wall/floor in PCCwith nuts and bolts made out of 2.0 mm thick CRCA sheet, having 13 Nos chamber for housing of 13 energy meters and SPN MCB with Peepingglass fixed PVC frame and one MCB SPN with fixing rail and suitable busbar chamber for fixing 05 Nos aluminium strips 300 Amp capacity each making holes for fixing aluminium lugs, complete internal wiring with 6 sqmm multistranded copper cable FRLSH, epoxy based bakelite sheet of suitable size for fixingof energy meters & MCBs, including indl chamber locking system & testingon completion completeall as directed. (Note: The quoted rate includes the cost of 13 nos MCB SPN 32 Amp complete). 127 Material and labour for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 6 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre,charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers,PCCchamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & as directed 128 M&L for Sand cushioning/sand coveringfor underground cable protection complete all as specified.Note: Punned thickness only will be measured and paid. 129 Supply and layingreinforced precast concrete cable cover, classClass LV, Type I, flat, size 250 mm x 150mm x 40mm at right angle laid along alignment of cable as protection to cable in trenches complete all as specified and directed by Engineer-in-Charge 130 Supply, fixing ,Teting and commissioning XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables ( heavy duty) with stranded aluminum conductor, 1100Volt grade on walls with fixing acessories of35 Sqmm 3.5 Core all as specified and directed.

BRR:7504532 Tender For Supply Of Civil Constriction Goods Under Mnrega And Other Scheme For Session 2025-26 Gram Panchayat Somka Panchayat Samiti Pahadi - Ghadla/Kankar/Jhajhra2 Mortar-soil/mud masala3 Lime from Kali kiln for masonry work4 P.P.C.5 White cement6 Sand/gravel7 Gravel - Local8 Fly ash9 Surkhi10 Stone dust (in masonry work)11 Stone 40mm measured (hand broken grit) (cut voids 1/11)12 Stone 40mm grit (broken by crusher) (cut voids 1/11)13 Stone 20mm grit (broken by crusher)14 Stone 12/10/6mm grit (broken by crusher)15 Brick aggregate16 63-40mm stone crushed stone aggregate (cut voids 1/11)17 90-45mm. Hand broken stone aggregate(Cut voids 1/11)18 Quarry rubbish(Cut voids 1/6)19 Gravel(Cut voids 1/6)20 Kankar(Cut voids 1/6)21 Binding material (PI 4-6)(Cut voids 1/6)22 I st class)23 II class24 Masonry rubble (RR)25 Masonry rubble (CR)26 Kharanja soling (upto 15cm height for flooring work)27 Kharanja soling (upto 23cm height for road/Kharanja work)28 Upto 25mm thickness29 Upto 25-40mm thickness30 Upto 40-50mm thickness31 Upto 50-75mm thickness32 Upto 75-100mm thickness33 Upto 100-150mm thickness34 Flooring sheets upto 35mm Thick, min. 3 sqft or more Area35 Strip sheet for paving 60-75mm thickness, min. 3 sqft or more Area36 Upto 900 sq.cm37 Upto 901 to 2300 sq.cm38 More than 2300 sq.cm39 Upto 900 sq.cm40 Upto 901 to 2300 sq.cm41 More than 2300 sq.cm42 Upto 901 to 2300 sq.cm43 Upto 900 sq.cm44 More than 2300 sq.cm45 Marble Chips46 Marble Powder47 Upto 901 to 2300 sq.cm48 Upto 900 sq.cm49 More than 2300 sq.cm50 Single Patam Size 100 X 75 mm.51 Double Patam Size 125 X 75 mm.52 Up to 1.5 m Length, Minimum 40mm thick53 1.5 m to 2.40 m Length, Minimum 50mm thick54 2.4 m to 3.0 m Length, Minimum 65mm thick55 Above 3.0 m Length, Minimum 75mm thick56 Glazed Size-30X45 cm57 Mosaic Size-40mm Thick58 Vitrified Size-60X60 cm59 Cement Interlocking Block M-30grade, 60mm Thick60 Cement Interlocking Block M-30grade, 80mm Thick61 Cement Interlocking Block M-30grade, 100mm Thick62 1.50 sq. mm.63 2.50 sq. mm.64 0.50 sq.mm65 1.00 sq. mm.66 4.00 sq. mm.67 6.00 sq. mm.68 Mango69 Acacia70 Others71 Factory made doors (30mm thick, solid core single leaf)72 Iron (Tor Steel Fe 415/500 for reinforcement)73 Winding wire 18 gauge74 Iron girders75 Conical iron/Square bar/Patti/Angle iron76 Barbed iron wire (Size 12 guage wire and 12 guage strad/12 guage wire and 14 guage strad/14 guage77 Iron mesh (24 gauge, 14 mesh)78 Cement concrete mesh Akash Patal 40mm thick79 3mm thick glass80 Enamel paint81 Distemper (Water Bound)82 Lime - for whitewashing (Aras / Kali)83 Primer(for iron/wood)84 Diesel HSD85 Movil Oil86 Bitumen Shalitex Board (25 mm Thick)87 G.I. Sheet 22 Gauge (0.80 mm)88 G.I. Sheet 24 Gauge(0.63 mm)89 M.S. Sheet 22 Gauge (0.80 mm)90 M.S. Sheet 24 Gauge (0.63 mm)91 G.I. Sheet 1 mm Thick92 G.I. Sheet 22 Gauge(0.80 M.M.)93 Asbestos Cement Sheet 6mm(2.5/2.75X1m)94 P.V.C. Sheet 1 mm Thick (Coloured/Plain)95 Green Yellow Literof Expo Sheet(183X90)96 GI 15mm Diameter(B Class)97 GI 20mm Diameter(B Class)98 GI 25mm Diameter(B Class)99 AC 75mm Diameter100 AC 100mm Diameter101 PVC 90mm Diameter(with ring)102 PVC 110mm Diameter(with ring)103 PVC 140mm Diameter(with ring)104 PVC 110mm(2.5kg/sq.cm) with coupler105 Indian W.C.106 Orrisa W.C.107 European W.C.108 Foot Rest109 Porcelain lipped urinal 430*350*300mm with coupler, bracket and PVC waste pipe110 Wash-basin 450*300mm with coupler, bracket and PVC waste pipe111 Stone furnace (S.W.) pipe 100 mm diameter, 0.6 m long112 CP pillar cock (dia 15 mm) (IS Mark)113 CP bib cock (dia 15 mm) (IS Mark)114 CP grating of 125 mm diameter115 1200 mm diameter116 1000 mm diameter117 750 mm diameter118 600mm dia119 450mm dia120 300mm dia121 20mm dia122 25mm dia123 Charcoal124 PVC Water Tank with Cover (Conforming to IS:12701-1989) 500 litres125 13/0.20mm Twin Core PVC Shelled, Flat Flexible Copper Cable126 Steel Fastener 6mm x 75mm127 25mm dia128 20mm dia129 20mm Two Way130 20mm, One Way131 25mm Two Way132 20mm One Way (PVC)133 3 for module134 2 for module135 2 for module136 3 for module137 SP 15/16 ampere138 SP 5/6 ampere139 3 pin 5/6 ampere140 6 pin 15/16 ampere141 2+2 way, SPN, single door142 2+4 way, SPN, single door143 2+6 way, SPN, single door144 15.00 mm dia145 40.00 mm dia146 Copper wire 8 SWG (4.00 mm dia) (0.117 kg/m)147 CI/MS cover plate, attached to frame with locking arrangement148 Diesel road roller 8 se 10 Ton149 Sheep Foot Roller150 Truck 9 Ton151 Tractor (25-40 HP)152 Tractor Trolley153 Tractor Water Tanker Capacity 4000 Litres Water154 Cement Concrete Mixer 5-7 Cubic Feet155 Pumping Set 15 HP156 Niddle/Plate vibrator with operator157 Camel cart/Bullock cart with driver158 Grinding machine with operator (big, motor driven)159 Compressor160 Hydraulic Excavater/JCB (bucket capacity 0.4cum)161 Dumper162 Scraper163 Shuttering of wooden planks, with poles and other materials along with TP, to be installed at site, removed after the specified period164 Shuttering of ply, with poles and other materials along with TP, to be installed at site, removed after the specified period165 Shuttering of iron plate, with poles and other materials along with TP, to be installed at site, removed after the specified period166 Water and pumping expenses (filling)167 Grinding machine with operator (small, hand operated)168 Iron for well Farm (diameter 3m, height 75cm) with TP, installed on site, removed after specified period169 Cultivator

BRR:7504530 Tender For Retender For Material Supply Under Mgnrega Scheme In Fy 2025-26 Gp Dharnok - Ghadla/Kankar/Jhajhra2 Mortar-soil/mud masala3 Lime from Kali kiln for masonry work4 Cement PPC5 White Cement6 Fine Aggregate Sand/Grabble7 Gravel - Local8 Fly Ash9 Surkhi10 Stone Dust (In Masonry Work)11 Ballast Stone/Brick (For Other than Road work) 40mm measured stone (Grit broken by hand) (Voids cut 1/11)12 40mm stone (Broken by crusher) (Voids cut 1/11)13 20mm stone (Broken by crusher)14 12/10/6mm stone (Broken by crusher)15 Brick ballast16 Material for Road Work (Including 5 Km. Lead) 63-40mm stone crushed stone (Voids cut 1/11)17 63-40mm hand crushed stone Crushed stone aggregate(cut voids 1/11)18 90-45 mm. Hand broken stone aggregate(Cut voids 1/11)19 Quarry rubbish(Cut voids 1/6)20 Gravel(Cut voids 1/6)21 Kankar(Cut voids 1/6)22 Binding material (PI 4-6)(Cut voids 1/6)23 Brick (22.5 X 11 X 7.50 cm) I st class24 II class25 Soling/ Kharanja/ Masonry stone Masonry Beradda (RR)26 Masonry Radda (CR)27 Kharanja soling (for flooring work upto 15cm height)28 Kharanja soling (for road/ Kharanja work upto 23cm height)29 Jodhpuri type stone strips/arches/cuts (length 2-3, width 10-12, thickness 2.5-3.5)30 Stone chips (Flaky Material)(3-4 Thick & Length and Width 1-2)31 Sandstone(DPC,Sill,Coping,Lintel,Tand,Almirha etc)Upto 25mm thickness32 Upto 25-40mm thickness33 Upto 40-50mm thickness34 Upto 50-75mm thickness35 Upto 75-100mm thickness36 Upto 100-150mm thickness37 Flooring/Strip Patan Katla StoneFlooring slabs upto 35mm Thick, min. 3 sqft or more Area38 Strip Patan slabs 60-75mm Thickness, min. 3 sqft or more Area39 Unpolished Rough Kota StoneUpto 900 sq.cm40 901 to 2300 sq.cm41 Above 2300 sq. cm42 Polished Kota Stone(One side polished)Upto 900 sq. cm43 From 901 to 2300 sq. cm44 Above 2300 sq. cm45 Marble Stone(Makrana Adanga 20mm Thick)Upto 901 to 2300 sq. cm46 Upto 900 sq. cm47 Above 2300 sq. cm48 Marble Chips49 Marble Powder50 Marble Stone(Rajnagar II Quality/Local 20mm Thick)Upto 900 sq. cm51 From 901 to 2300 sq. cm52 Above 2300 sq. cm53 Stone FrameSingle Paitaam Size 100 X 75 mm.54 Double Paitaam Size 125 X 75 mm.55 Stone Straps Up to 1.5 m Length, Minimum 40mm thick56 1.5 m to 2.40 m Length, Minimum 50mm thick57 2.4 m to 3.0 m Length, Minimum 65mm thick58 Above 3.0 m Length, Minimum 75mm thick59 Precast Tiles / Blocks Glazed Size-30X45 cm60 Mosaic Size-40mm Thick61 Vitrified Size-60X60 cm62 Interlock Tiles/Brick/Block for Road Work Cement Interlocking Block M-30grade, 60mm Thick63 Cement Interlocking Block M-30grade, 80mm Thick64 Cement Interlocking Block M-30grade, 100mm Thick65 FR PVC Insulated Copper Conductor Single Core Cable ISI Marked1.50 Sq. mm.66 2.50 sq. mm.67 0.50 sq. mm.68 1.00 sq. mm.69 4.00 sq. mm.70 6.00 sq. mm.71 Local wood with fittings (for doors, windows and furniture) Mango72 Acacia73 Others74 Factory made doors (30 mm thick, solid core single leaf)75 Structural steel Iron (Tor steel Fe 415/500 for reinforcement)76 Winding wire 18 gauge77 Iron girders78 Conical iron/ square bars/ leaf/ angle iron79 Barbed iron wire (Size 12 guage wire and 12 guage strad/12 guage wire and 14 guage strad/14 guage80 MeshIron Mesh (24 Gauge, 14 Mesh)81 Cement Concrete Mesh Akash Patal 40 mm Thick82 Glass3 mm thick glass83 PaintEnamel Paint84 Distemper (Water Bound)85 Lime - For Painting (Aras / Kali)86 Primer (For Iron / Wood)87 Petroleum Product Diesel HSD88 Movil Oil89 Bitumen Shalitex Board (25 mm Thick)90 Plain Sheet (Plain Sheet)GI Sheet 22 Gauge (0.80 mm)91GI Sheet 24 Gauge (0.63 mm)92MS Sheet 22 Gauge (0.80 mm)93MS Sheet 24 Gauge (0.63 mm)94 Corrugated Sheet GI Sheet 1mm thick95 GI Sheet 22 Gauge(0.80 M.M.)96 Asbestos Cement Sheet 6mm(2.5/2.75X1m)97 Other Sheets PVC Sheet 1mm thick (Coloured/Plain)98 Green Yellow Literof Expo Sheet(183X90)99 Pipe GI 15mm Diameter(B Class)100 GI 20mm Diameter(B Class)101 GI 25mm Diameter(B Class)102 A.C. 75mm Diameter103 A.C. 100mm Diameter104 P.V.C. 90mm Diameter Diameter(with ring)105 PVC 110 mm. Diameter(with ring)106 PVC 140 mm. Diameter(with ring)107 PVC 110 mm.(2.5kg/sq.cm) with coupler108 Sanitary Indian W.C.109 Orrisa W.C.110 European W.C.111 Foot Rest112 Porcelain Urinal 430*350*300 mm with coupler, bracket and PVC waste pipe113 Wash-Basin 450*300 mm with coupler, bracket and PVC waste pipe114 Stone furnace (S.W.) pipe 100 M.M. diameter, 0.6 m long115 C.Pillar Cock (dia 15 mm) (IS Mark)116 CP Bib Cock (dia 15 mm)(IS Mark)117 RCC NP3 Hume Pipe with Collar 1200mm Dia118 1000mm diameter119 750mm diameter120 600mm diameter121 450mm diameter122 300mm diameter123 Steel Conduit ISI Marked 20 mm. Diameter124 25 mm Diameter125 charcoal126 pvse. Water Tank with Cover (Conforming to IS:12701-1989)127 13/0.20 mm Twin core PVC sheathed, flat flexible copper cable128 Steel fasteners 6 mm x 75 mm129 PVC Conduit ISI Marked 25 mm Diameter130 20 mm Diameter131 Junction Box 20 mm Two way132 20 mm, One way133 25 mm Two way134 20 mm One way (PVC)135 Module GI Box for 3 modules136 for 2 modules137 Module Base & Cover Plate for 2 modules138 for 3 modules139 Modular Switch One way, ISI Marked SP 15/16 Ampere140 SP 5/6 Ampere141 Modular Socket Outlet, ISI Marked3 pin 5/6 Ampere142 6 pin 15/16 Ampere143 MCB DB2+2 way, SPN, single door144 2+4 way, SPN, single door145 2+6 way, SPN, single door146 GI Pipe (Medium Grade)15.00 mm Diameter147 40.00 mm Diameter148 Copper Wire 8 SWG (4.00 mm Diameter) (0.117 Kg/m)149 CI/MS Cover Plate, attached to frame with locking arrangement150 Diesel Road Roller 8 to 10 Ton151 Sheep Foot Roller152 Truck 9 Ton153 Tractor (25-40 HP)154 Tractor Trolley155 Tractor Water Tanker Capacity 4000 Litres Water156 Cement Concrete Mixer 5-7 Cubic Feet157 Pumping Set 15 HP158 Niddle/Plate Vibrator with Operator159 Camel Cart/Bullock Cart with Driver160 Grinding Machine with Operator (Large, Motor Driven)161 Compressor162 Hydraulic Excavater/JCB (Bucket Capacity 0.4cum)163 Dumper164 Scraper165 Shuttering of wooden planks, including poles and other materials along with TP, to be installed at site, removed after stipulated period166 Shuttering of ply, including poles and other materials along with TP, to be installed at site, removed after stipulated period167 Shuttering of iron plate Key, including poles and other materials along with TP, to be installed at the site, removed after the stipulated period168 Water and pumping expenses (filling)169 Grinding machine with operator (small, hand operated)170 Iron form for well (diameter 3m, height 75cm) along with TP, to be installed at the site, removed after the stipulated period171 Cultivator

BRR:7504529 Tender For Supply Of Construction Material For Works Gram Panchayat Dharnok - Ghadla/Kankar/Jhajhra2 Mortar-soil/mud masala3 Lime from Kali kiln for masonry work4 Cement PPC5 White Cement6 Fine Aggregate Sand/Grabble7 Gravel - Local8 Fly Ash9 Surkhi10 Stone Dust (In Masonry Work)11 Ballast Stone/Brick (For Other than Road work) 40mm measured stone (Grit broken by hand) (Voids cut 1/11)12 40mm stone (Broken by crusher) (Voids cut 1/11)13 20mm stone (Broken by crusher)14 12/10/6mm stone (Broken by crusher)15 Brick ballast16 Material for Road Work (Including 5 Km. Lead) 63-40mm stone crushed stone (Voids cut 1/11)17 63-40mm hand crushed stone Crushed stone aggregate(cut voids 1/11)18 90-45 mm. Hand broken stone aggregate(Cut voids 1/11)19 Quarry rubbish(Cut voids 1/6)20 Gravel(Cut voids 1/6)21 Kankar(Cut voids 1/6)22 Binding material (PI 4-6)(Cut voids 1/6)23 Brick (22.5 X 11 X 7.50 cm) I st class24 II class25 Soling/ Kharanja/ Masonry stone Masonry Beradda (RR)26 Masonry Radda (CR)27 Kharanja soling (for flooring work upto 15cm height)28 Kharanja soling (for road/ Kharanja work upto 23cm height)29 Jodhpuri type stone strips/arches/cuts (length 2-3, width 10-12, thickness 2.5-3.5)30 Stone chips (Flaky Material)(3-4 Thick & Length and Width 1-2)31 Sandstone(DPC,Sill,Coping,Lintel,Tand,Almirha etc)Upto 25mm thickness32 Upto 25-40mm thickness33 Upto 40-50mm thickness34 Upto 50-75mm thickness35 Upto 75-100mm thickness36 Upto 100-150mm thickness37 Flooring/Strip Patan Katla StoneFlooring slabs upto 35mm Thick, min. 3 sqft or more Area38 Strip Patan slabs 60-75mm Thickness, min. 3 sqft or more Area39 Unpolished Rough Kota StoneUpto 900 sq.cm40 901 to 2300 sq.cm41 Above 2300 sq. cm42 Polished Kota Stone(One side polished)Upto 900 sq. cm43 From 901 to 2300 sq. cm44 Above 2300 sq. cm45 Marble Stone(Makrana Adanga 20mm Thick)Upto 901 to 2300 sq. cm46 Upto 900 sq. cm47 Above 2300 sq. cm48 Marble Chips49 Marble Powder50 Marble Stone(Rajnagar II Quality/Local 20mm Thick)Upto 900 sq. cm51 From 901 to 2300 sq. cm52 Above 2300 sq. cm53 Stone FrameSingle Paitaam Size 100 X 75 mm.54 Double Paitaam Size 125 X 75 mm.55 Stone Straps Up to 1.5 m Length, Minimum 40mm thick56 1.5 m to 2.40 m Length, Minimum 50mm thick57 2.4 m to 3.0 m Length, Minimum 65mm thick58 Above 3.0 m Length, Minimum 75mm thick59 Precast Tiles / Blocks Glazed Size-30X45 cm60 Mosaic Size-40mm Thick61 Vitrified Size-60X60 cm62 Interlock Tiles/Brick/Block for Road Work Cement Interlocking Block M-30grade, 60mm Thick63 Cement Interlocking Block M-30grade, 80mm Thick64 Cement Interlocking Block M-30grade, 100mm Thick65 FR PVC Insulated Copper Conductor Single Core Cable ISI Marked1.50 Sq. mm.66 2.50 sq. mm.67 0.50 sq. mm.68 1.00 sq. mm.69 4.00 sq. mm.70 6.00 sq. mm.71 Local wood with fittings (for doors, windows and furniture) Mango72 Acacia73 Others74 Factory made doors (30 mm thick, solid core single leaf)75 Structural steel Iron (Tor steel Fe 415/500 for reinforcement)76 Winding wire 18 gauge77 Iron girders78 Conical iron/ square bars/ leaf/ angle iron79 Barbed iron wire (Size 12 guage wire and 12 guage strad/12 guage wire and 14 guage strad/14 guage80 MeshIron Mesh (24 Gauge, 14 Mesh)81 Cement Concrete Mesh Akash Patal 40 mm Thick82 Glass3 mm thick glass83 PaintEnamel Paint84 Distemper (Water Bound)85 Lime - For Painting (Aras / Kali)86 Primer (For Iron / Wood)87 Petroleum Product Diesel HSD88 Movil Oil89 Bitumen Shalitex Board (25 mm Thick)90 Plain Sheet (Plain Sheet)GI Sheet 22 Gauge (0.80 mm)91GI Sheet 24 Gauge (0.63 mm)92MS Sheet 22 Gauge (0.80 mm)93MS Sheet 24 Gauge (0.63 mm)94 Corrugated Sheet GI Sheet 1mm thick95 GI Sheet 22 Gauge(0.80 M.M.)96 Asbestos Cement Sheet 6mm(2.5/2.75X1m)97 Other Sheets PVC Sheet 1mm thick (Coloured/Plain)98 Green Yellow Literof Expo Sheet(183X90)99 Pipe GI 15mm Diameter(B Class)100 GI 20mm Diameter(B Class)101 GI 25mm Diameter(B Class)102 A.C. 75mm Diameter103 A.C. 100mm Diameter104 P.V.C. 90mm Diameter Diameter(with ring)105 PVC 110 mm. Diameter(with ring)106 PVC 140 mm. Diameter(with ring)107 PVC 110 mm.(2.5kg/sq.cm) with coupler108 Sanitary Indian W.C.109 Orrisa W.C.110 European W.C.111 Foot Rest112 Porcelain Urinal 430*350*300 mm with coupler, bracket and PVC waste pipe113 Wash-Basin 450*300 mm with coupler, bracket and PVC waste pipe114 Stone furnace (S.W.) pipe 100 M.M. diameter, 0.6 m long115 C.Pillar Cock (dia 15 mm) (IS Mark)116 CP Bib Cock (dia 15 mm)(IS Mark)117 RCC NP3 Hume Pipe with Collar 1200mm Dia118 1000mm diameter119 750mm diameter120 600mm diameter121 450mm diameter122 300mm diameter123 Steel Conduit ISI Marked 20 mm. Diameter124 25 mm Diameter125 charcoal126 pvse. Water Tank with Cover (Conforming to IS:12701-1989)127 13/0.20 mm Twin core PVC sheathed, flat flexible copper cable128 Steel fasteners 6 mm x 75 mm129 PVC Conduit ISI Marked 25 mm Diameter130 20 mm Diameter131 Junction Box 20 mm Two way132 20 mm, One way133 25 mm Two way134 20 mm One way (PVC)135 Module GI Box for 3 modules136 for 2 modules137 Module Base & Cover Plate for 2 modules138 for 3 modules139 Modular Switch One way, ISI Marked SP 15/16 Ampere140 SP 5/6 Ampere141 Modular Socket Outlet, ISI Marked3 pin 5/6 Ampere142 6 pin 15/16 Ampere143 MCB DB2+2 way, SPN, single door144 2+4 way, SPN, single door145 2+6 way, SPN, single door146 GI Pipe (Medium Grade)15.00 mm Diameter147 40.00 mm Diameter148 Copper Wire 8 SWG (4.00 mm Diameter) (0.117 Kg/m)149 CI/MS Cover Plate, attached to frame with locking arrangement150 Diesel Road Roller 8 to 10 Ton151 Sheep Foot Roller152 Truck 9 Ton153 Tractor (25-40 HP)154 Tractor Trolley155 Tractor Water Tanker Capacity 4000 Litres Water156 Cement Concrete Mixer 5-7 Cubic Feet157 Pumping Set 15 HP158 Niddle/Plate Vibrator with Operator159 Camel Cart/Bullock Cart with Driver160 Grinding Machine with Operator (Large, Motor Driven)161 Compressor162 Hydraulic Excavater/JCB (Bucket Capacity 0.4cum)163 Dumper164 Scraper165 Shuttering of wooden planks, including poles and other materials along with TP, to be installed at site, removed after stipulated period166 Shuttering of ply, including poles and other materials along with TP, to be installed at site, removed after stipulated period167 Shuttering of iron plate Key, including poles and other materials along with TP, to be installed at the site, removed after the stipulated period168 Water and pumping expenses (filling)169 Grinding machine with operator (small, hand operated)170 Iron form for well (diameter 3m, height 75cm) along with TP, to be installed at the site, removed after the stipulated period171 Cultivator

BRR:7504384 Soil Mechanics Lab Equipments Soil Mechanics Lab Equipment , Soil Mechanics Lab Equipments , Pycnometer , Hot Air Oven With All Accessories , Relative Density Apparatus , Liquid Limit Device , Plastic Limit Apparatus , Direct Shear Apparatus With Proving Ring And Dial Gauge: , Proctor Compaction Test Apparatus , Soil Sampling Apparatus , Sand Pouring Cylinder , Electronic Balance -1 Kg Accuracy , Electronic Weighing Balance 100Kg Accuracy => Limited

BRR:7504285 Bids Are Invited For Testing Of Vernacular Typologies Bhutia And Bhunga , Planetary Mixer Used For Testing Of Cement And Pozzolana Total Quantity : 1

BRR:7504247 Bids Are Invited For Weighbridge For Dvc Btps Track Switch For Rail Weighbridge, Rail Weigh Bridge Model No. Cim-9000, Make- Pragati Instrumentation Pvt Ltd , Display Card For Rail Weigh Bridge, Rail Weigh Bridge Model No. Cim-9000, Make- Pragati Instrumentation Pvt Ltd , Jb Card Model No. Pipl-Jb-Ver 1.0, Standard 12 Volts, Make- Pragati Instrumentation Pvt. Ltd. , A.D. Card With Standard 16 Bit And 100 K S, Make- Pragati Instrumentation Pvt Ltd , Digitizer Cpu Card For Rail Weigh Bridge, Rail Weigh Bridge Model No.- Cim-9000, Make- Pragati Instrumentation Pvt Ltd , Relay Board For Rail Weigh Bridge, Rail Weigh Bridge Model No. Cim-9000, Make- Pragati Instrumentation Pvt Ltd , Power Card Model No. Pipl-Ims-Ps-Ver1.0, Make- Pragati Instrumentation Pvt Ltd Track Switch For Rail Weighbridge (Rail Weigh Bridge Model No. Cim-9000), Display Card For Rail Weigh Bridge (Rail Weigh Bridge Model No. Cim-9000), Jb Card Model No. Pipl-Jb-Ver 1.0, Standard 12 Volts, A.D. Card With Standard 16 Bit & , Electronic Weighing Scales Electronic Weigh Bridge (Without Civil Work) Total Quantity : 10

BRR:7504108 Bids Are Invited For Repair and Overhauling Service - Dimensioning and Weighing Systems (Volumetric weighing machine); HYD TEST BENCH; Yes; Buyer Premises Total Quantity :

BRR:7503757 Bids Are Invited For Microsemi-Microanalytical Weighing Balance (Q2) Total Quantity : 1

BRR:7503544 Bids Are Invited For Repair and Overhauling Service - REPAIR OF STATIC MOVEMENT WEIGHING MACHINE; REPAIR OF STATIC MOVEMENT WEIGHING MACHINE; Yes; Buyer Premis Total Quantity :

BRR:7502911 Bids Are Invited For Electronic Baby Weighing Scale - Rbsk (Q3) 2 Year (S) Total Quantity : 11

BRR:7502910 Bids Are Invited For Repairing Of Los Angeles Machine , Planetary Mixer Used For Testing Of Cement And Pozzolana Total Quantity : 1

BRR:7502519 Tender For Road Construction Work In Sanjay Nagar Colony - Dismantling of Cut Stone as per S.O.R. 2020 Chapt18 D, S l. No. 4(b) Page 49 2 Excavation in founadtion in ordinary soil (loamclay or sand) including lift up to 1.5 m and lead up to 30m. And including filling watering and ramming of excavated earth into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the engineer-in-charge upto a distance of 30m, from the foundation trenches including all T & P phowarah and basket etc. complete.S.I. No-251 3 Concrete with 4cm. Gauge brick ballast, sand of 1.25 F.M. and cement in proportion of 1:6:12 in foundation and under floors including supply of all materials labour and tools and plants etc. required for proper completion for the work S.I. No-273 4 M-150 brick work in 1:4 Cement and sand of 1.25 fineness modulous mortar in foundation and plinth including supply of all material, labour and T&P etc. required for proper completion of work.S.I. No-305 5 12 mm thick cement plasterin 1:4 cement morter I/C all material labour T&P proper complition to the work . S.I. No-584 6 Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavatorat OMC, and compacting with smoothwheelroller to achieve thedesired density, complete as per Technical Specification Clause 401. 7 Construction ofun-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design,laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawingand Technical Specification Clause 1501 8 Construction of K.C. drain with precast of C.C. Blocks size (400x325 mm) laid in flat position (37.5 mm in length )and kerb stone (300mm in length)including cost of Base Concrete in 1:6:12 cement sand and O.B.B Including cost of all material labourT&P etc,proper complition to the work . as per S.E.RED VNS Estimate no 01 dt- 22.08.2015 9 S/Fixing of infomataryM.Ssign board Size (1.2x0.90) Made of 18 mm gauge M.S.Sheet fixed in ISA 40x40x5 mm frame supported in back side by 40x5 mm fiat iron on all four side along with two vertical pont of 2.15 mt from bottom of frame of angle iron ISA 40X40X5 mm with 150 mm long horizontal lag at bottom braded with 40x5 mm flat iron ellectrically welded and pointed with one coat red oxide primer S.S. NO. 503

BRR:7502472 Tender for Chandrikachandikkudy Road Chandrikachandikkudy Road Tile Paving , Smooth Wheeled Roller 8 To 10 Tonne , Water Tanker 5 To 6 Kl Capacity , Water , Well Graded Material For Sub Base Grading I, 53 Mm To 9.5 Mm Below @ 50 Percent , Well Graded Material For Sub Base Grading I, 9.5 Mm To 2.36 Mm Below @ 20 Percent , Well Graded Material For Sub Base Grading I, 2.36 Mm Below @ 30 Percent , Interlocking C.C. Paver Block (80 Mm Thick, M-30) , Stone Aggregate(Single Size): 06 Mm Nominal Size , Stone Aggregate(Single Size):20 Mm Nominal Size , Stone Aggregate(Single Size): 10 Mm Nominal Size , Coarse Sand (Zone Iii) , Portland Cement , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With Hopper , Vibrator (Needle Type 40 Mm) , Sundries

BRR:7502471 Tender For supply of material for K K Road K K Road Tile Paving , Smooth Wheeled Roller 8 To 10 Tonne , Water Tanker 5 To 6 Kl Capacity , Water , Well Graded Material For Sub Base Grading I, 53 Mm To 9.5 Mm Below @ 50 Percent , Well Graded Material For Sub Base Grading I, 9.5 Mm To 2.36 Mm Below @ 20 Percent , Well Graded Material For Sub Base Grading I, 2.36 Mm Below @ 30 Percent , Interlocking C.C. Paver Block (80 Mm Thick, M-30) , Stone Aggregate(Single Size): 06 Mm Nominal Size , Stone Aggregate(Single Size):20 Mm Nominal Size , Stone Aggregate(Single Size): 10 Mm Nominal Size , Coarse Sand (Zone Iii) , Portland Cement , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With Hopper , Vibrator (Needle Type 40 Mm) , Sundries

BRR:7502404 Tender For Annual Plan-Ptdu-401/25-Mayyathankara Muslim Palli Road Maintanance Ward 18-General Civil Work - Concreting 2 75.8.1.1.A:Providing Plain cement concrete for wearing coat CC 1:2:4 (1 cement: 2 fine aggregate:4 course aggregate) laid to required slope as required including compaction, finishingand tamping etc .complete. Max. size of course aggregate not exceeding 25mm , mixedin concrete mixer etc complete as per specification (i) Nominal mix (1:2:4) 3 75.8.1:Providing Plain cement concrete for road work CC 1:2:4 (1 cement: 2 fine aggregate: 4course aggregate) laid to required slope and camber in panels (@ 3 m c/c) as requiredincluding compaction, finishing and tamping etc .complete. Max. size of courseaggregate not exceeding 25mm , mixed in concrete mixer etc complete as perspecification (i) Nominal mix (1:2:4)

BRR:7501973 Tender For Comprehensive Maint To Central Amenities Under Age Br Ii At Rms; 1 M&L 15mm thick plastering in CM (1:4) on one side of lathing in two separate layers without using extra cement but using water proofing compound @ 3% by wt of cement and surface finished even and smooth including demolition of reed, lathing single or double, including battens and plaster or chicken wire lathing with and including M&L for GI wire netting 0.71 mm dia and 12 mm mesh lathing in to reed in walls incl all laps cutting and waste complete all as specified and as directed.Note:-WPC will be measured and paid separately. 2 M&L for rendering 12 mm thick in CM (1:6) on other side of lathing surface finished even and smooth without using extra cement complete all as specified and as directed. 3 M&L brick work with sub class B bricks(using old size burnt bricks) straight or curved on plan to any radius in half brick thick walls built in CM (1:4) including demolition of old brick work complete all as specified and as directed. 4 M&L for brick work with sub class B bricks(using old size burnt bricks) straight or curved on plan exceeding 6 m mean radius, built in Cement Mortar (1:6) including demolition of old brick work complete all as specified and as directed. 5 S & F second class hardwood weather boarding, clean sawn, plain, 20 mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps complete all as specified and as directed. 6 M&L for second class hardwood as in scantlings clean sawn timberfixed including dismantling of old unsv timber scantling complete all as specified and as directed. 7 Taking down Chowkhat or frames not exceeding 1.5 Sqm each with shutters(Without taking off shutters from the frames complete all as specified and as directed. 8 Taking down chowkhat or frames exc 1.5 Sqm but not exc 4 Sqm each (without taking off shutter from the frame) complete all as specified and as directed. 9 S&F Pressed steel frames of size 125 X 60mm (Thickness of MS Sheet 1.25mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete as specified, supplied and fixed etc complete all as specified and directed. 10 S&F factory made 30mm thick, flush shutters, solid core construction, with particle board core and plywood face panels complete all as specified and as directed. 11 S&F for second class hardwood glazed and skeleton door shutters, 30mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beeds for securing glass etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (b); supplied and fitted to chowkats complete all as specified and as directed. 12 S&F Powder Coated aluminium colour frame for doors, windows, ventilators and partition etc with one or more rebates including joining cleat for fixing complete all as specified and as directed. 13 S&F Powder Coated aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats,glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specifie 14 S&F for powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium section of size 40 x 18 x 1.29mm thick including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws complete all as specified and as directed. 15 S&F sheet glass 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and as directed. 16 S&Ffor galvanised mild steel wire cloth, 0.56 nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed. 17 S & F 100 size stainless steel butt hinges complete all as specified and directed. 18 Supply & Fixing150 mm Aluminium handles, cast type, anodised complete all as specified and as directed. 19 S & F 200 mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed. 20 S & F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed complete all as specified and as directed. 21 M&L for preparation of new plastered or un plasteredsurface of walls including cornices, pilasters etc and applying two coats of cement base paint over and including a coat of primer complete all as specified and directed. 22 M&L for applying two coats of oil bound distemper on new plastered surfaces of walls including preparation of surface complete all as specified and as directed. 23 M&L for preparation of newsurfaces of steel and iron work of any description over 10 cm width or girth not otherwise described andapplying two coats of synthetic enamel paint over and including a coat of red oxide primer on new surfaces in any tint complete all as specified and as directed. 24 M&L for preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. 25 M&L preparation of old surfaces of wallsapplying one coat of cement base paint complete all as specified and as directed. 26 M&L for Preparation of old decorated surfaces by washing, scrubbing down, and applying one coat of oilbound distemper on walls complete all as specified and as directed. 27 Demolition, Cement concreteof any description and in any position not otherwise specifically provided for complete all as specified and as directed by the Engineer-in-Charge. 28 M&L for 75 mm thick PCC (1:3:6) type C-2 , (using 40 mm graded stone aggregate) in plinth protection/aprons/path laid to slope of 1:12, finished fair and even without using extra cement with and including all necessary formwork to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 10 mm wide joints throughout thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and as directed. 29 M&L for Vitrified Ceramic tiles (Light shade) of size 600mmx600mm x (9-10) mm thick (square/ rectangular) polished, laid in floorsover and including 15mm thick screed bed or bedding layer in CM (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles includingdemolition of old Stone slabs/tiles of any description removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. 30 All as per Item No. 29.00 (here-in-before) but on vertical surfaces such as skirting , dado risers to stepsover and including 10 mm thick bedding layer in CM (1:4). 31 M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm,in floors laid over and including 15mm thick screed bed or bedding layer in CM (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles includingdemolition of old Stone slabs/tiles of any description removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. 32 All as per Item No. 30.00 (here-in-before) but on vertical surfaces such as skirting , dado risers to stepsover and including 10 mm thick bedding layer in CM (1:4). 33 M&L for Glazed ceramic coloured tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile laid over and including baking coat of 10 mm thick in CM (1:4) includingdemolition of old Stone slabs/tiles of any description removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. 34 M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm,in floors laid over and including 15mm thick screed bed or bedding layer in CM (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tilesincludingdemolition of old Stone slabs/tiles of any description removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. 35 All as per Item No. 34.00 (here-in-before) but on vertical surfaces such as skirting , dado risers to stepsover and including 10 mm thick bedding layer in CM (1:4). 36 S & F,Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed. 37 S&F Factory made solid panel pvc doorshutter 30 mm thick (style) con-sisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be cov-ered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement suppling & fixing at site as per specification and drawing complete all as specified and as directed. 38 M&L for cement concrete type B-1 (1:2:4) (using 20 mm graded stone aggregate) as in surface channels and drains complete all as specified and as directed. 39 M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement incl firms mouldscomplete all as specified and as directed. 40 Demolition of cement concrete in reinforced of any description and in any position not otherwise specifically provided, complete all as specified & directed. 41 M&L for Cement concrete type B-1 (1:2:4), 40mm thick as in levelling course (using 20 mm graded stone aggregate),complete all as specified and as directed. 42 M&L for PCC (1:4:8) type D-2, 75 mm thick (using 20 mm graded stone aggregate) as in sub base of floor complete all as specified and as directed. 43 M&L for chequered cement concrete tiles of size not less than 300x300x25mm thick laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) etc, set, jointed and pointed in neat cement slurry with grey cement and pigments complete all as specified and directed. 44 M&L for TMT bars, 6 to 8mm, cut to length, bent to shape required including cranking,bending spirally for hooping for column, hooking ends and binding with and incl MS wire(annealed) not less than 0.9 mm dia complete all as specified and as directed. 45 M&L for precast cement concrete type B-1 (1:2:4)(Using 20 mm graded stone aggregate) as in cover slabs, manhole cover, chamber cover and drainge cover set in cement mortar 1:6 including necessary formwok complete all as specified and as directed. 46 S&F in repairstubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc, 15 mm bore complete all as specified and as directed. 47 S&F in repairs tubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc, 20 mm bore complete all as specified and as directed. 48 S&F in repairsvitreous china wash hand basin including brackets, white size (550 x 400) mm including cuttingfor and pinning in ends of brackets. Including Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed complete all as specified and as directed. 49 S&F in repairsvitreous china squatting pan, Orissa, pattern size 580 x 440 mm white with integral foot rests(excluding flushing cistern and flush pipe)including connection to trap and to flushing pipe, anti-syphonage pipe etc complete including making good to floor complete all as specified and as directed. 50 S&F in repairsVitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe incl Urinal spreader complete all as specified and directed. 51 S&F in repairs 10 ltrs capacity PVC valveless syphonic action type flushing cistern low level with inlet ball valve float and dual fluash type complete all as specified(Make Cera, F1020106) complete all as specified and directed. 52 S&F in repairs for 15mm dia of pipe CP bib taps cast copper alloy, fancy type, chromium plated with , screwed for iron pipe or for brass ferrule and fixed. 53 S& F in repairs Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot or ‘Cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed. 54 S&F in repairs for 15mm dia of pipe stopvalves,fancy type and chromium plated, screwed down high pressure ,screwed both ends for iron pipes or for Unions and fixed complete all as specified and as directed. 55 S&F in repairs PVC connection 15mm dia and 45cm long with two Nosof brass checknuts and washers complete all as specified and as directed. 56 S&F in repairs brass chromium plated shower rose 125 mm in size with or without swivel joints any size incl fixing to steel pipe or union, complete all as spfd & directed 57 Supply and fixing of Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed. 58 S&F grating doom 125mm dia with waste hole of PTMT (Min wt 40 gms) complete all as specified and as directed. 59 S&F in repairs 600mm long tubular towel rail brass chromium plated 20mm dia, D type 60cm long fixed with two plugs (Gutties) of 2nd class hard wood embeded in cement mortor 1:3 with MS screws complete all as specified and as directed. 60 S& F in repairs PVC mounted 5mm thick bevelled edge looking mirror 600 x 450mm including taking down old fixed with chromium plated brass screws and cup washers complete all as specified and as directed. 61 S&F in repair 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed under floor complete all as specified and as directed. 62 S&F in repair 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed under floor complete all as specified and as directed. 63 S&F of 110mm dia PVC (SWR) bends complete all as specified and as directed. 64 S&F 75mm PVC(SWR) bends any radius with acess door complete all as specified and as directed. 65 S&F of 75mm dia PVC (SWR) Vent cowl complete all as specified and as directed. 66 S & F 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed. 67 S&F in repairs for 75mm bore dia pipe Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays, including bolts & nuts & securing ends of stay to wall or roof complete all as specified and as directed. 68 S&F in repairs rotational moulded polyethylene 500 Ltrs Capacity water storage tanks(cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I) including ball brass valve, with polythelene float and fly nut complete screwed down for iron pipe of 20 mm dia complete all as specified and as directed. 69 S & F for4 mm thick of size 600x600mmHSPC (high pressure Steam Cured) pre-Painted self embossed, textured designer boardE-Board Classic to be fixed Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. fixed in ceiling flat or Sloping including dismantling of old unsv ceiling boards (fibre, pulp, insulation, etc.) any thickness including cover fillets of any description and at any location complete all as specified and as directed. 70 M&L for rendering 15mm thick in CM (1:6) on fair faces of brick work or concrete surfaces and finished fair and even without using extra cement including taking down old cement plastercomplete all as specified and as directed. 71 M&L for rendering 15mm thick in CM (1:4) other than fair faces of brick work or concrete surfaces and finished even and smooth without using extra cement including taking down old cement plastercomplete all as specified and as directed. 72 Material & labour 2nd class hardwood plain, solid straight chowkats and frames, wrought, framed rebated on the solid,rounded or chamfered, put together with glue pinned at joints including taking down old cement plastercomplete all as specified and as directed. 73 S & F Pre-painted galvatume aluminum zinc coated GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws including dismantling of oldAsbestos cement sheet (Corrugated, semi corrugated etc ) in roof covering /plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed. 74 S & F Pre-painted galvatume aluminum zinc coated GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws including dismantling of oldAsbestos cement sheet (Corrugated, semi corrugated etc ) in roof covering /plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed. 75 M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to GDE Fe 410-0-or Fe 310-0 quality-Aincluding dismantling of wrought iron or mild steel work of any description complete all as specified and as directed. 76 M & L for PCC 25mm thick type B-0, (1:2:4) (using 12.5 mm graded stone aggregate)as in levelling corse of floor complete all as specified and as directed. 77 M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete laid over 20mm thick screed bed in CM 1:3 complete all as specified and as directed. 78 S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specificationcomplete all as specified and as directed. 79 M&L for Solid PVC Wall Lining consisting of 5mm thick Plain or coloured with wood grains printed PVC sheet inclusive of solvent cement and fixing at site on PVC frameincluding dismantling of old unsv wall panelling (fibre, pulp, insulation, etc.) any thickness including cover fillets of any description and at any locationcomplete all as specified and as directed. 80 M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, laid over and including 20mm thick screed bed/bedding layer in cement mortar (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. 81 S&F in repairs 20mm diaHarrison rails, mild steel, chromium plated with fixing brackets, stops, rollers complete all as specified and as directed. 82 S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position completein all respect as specified complete all as specified and as directed. 83 S&F 2 mm thick anodised aluminium composite panel fixed in aluminium frame including necessary rubber beading, jointing cleats complete all as specified and as directed. 84 S&F in repairs, One Piece Closets vitreous china water closet Padestal pattern (white)including fixing bolts, flushing cistern and flush pipe and including EWC Sheet cover complete all as directed. 85 S&F in repairs WHB Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed for 15 mm bore dia of pipe complete all as specified and as directed. 86 S&F in repairs vitreous china water closet Padestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe and including EWC Sheet cover complete all as specified and as directed. 87 M&L for Point wiring in repairs complete with two runs of 1.5 sqmm single core PVC insulated FR-LSH cable1100 volts grade with multi-stranded copper conductors, drawn throughand including PVC double locked Casing & caping/PVC Conduit pipe medium grade including provision of 1.5 sqmm, FR-LSH, PVC insulated copper cable as earth continuity conductor connected to common earth dolly, including PVC rectagular box for mounting switches / sockets / regulators complete all as specified and as directed. 88 Onelight controlled by one, one way switch. 89 One Ceiling fan/ Exhaust fan point controlled by one, one wayswitch. 90 One 3 pin socket outlet 5 Amps on the same board with other switches. 91 One 3 pin socket outlet 5 Amps on theIndependent board 92 One bell pointcontrolled by one, one way switch . 93 All as per item No- 88.00 here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed. 94 S&F Switch Piano, flush type single pole, one way 5 Amps complete all as specified and as directed. 95 S&F Socket outlet, 2 in 1, 5 pin 5A flush type complete all as specified and as directed. 96 S&F Switch Socket combination, 2 in 1, 5 pin 6A flush type complete all as specified and as directed. 97 S&F Switch Socket combination, 2 in 1, 5 pin 6A/16A flush type complete all as specified and as directed. 98 S&F stepped type electronic fan regulator 100 Watt socket size flush type on the existing phenolic laminated sheet complete all as specified and as directed. 99 S&F in repair ceiling rose 3 terminal PVC/Polycarbonate isolated body with PVC round/squareblock complete all as specified and as directed. 100 S&F in replacement of Bell AC 230 volts musical type complete all as specified and as directed. 101 S&F in repair bell push switch 5 amps piano type flush typecomplete all as specified and as directed. 102 S&F in repairs 20W LED, 4, Wall mounted LED batten, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver.etc with all accessories internally pre-wired and fixing the same and connecting upwith flexible copper cable from ceiling rose to the light fittingcomplete all as specified and as directed. 103 S&F in repairs 09 W LED, 2, Wall mounted LED batten, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver.etc with all accessories internally pre-wired and fixing the same and connecting upwith flexible copper cable from ceiling rose to the light fittingcomplete all as specified and as directed. 104 S&F in repairs Lamp holder , PVC/ Polycarbonate type with PVC round/square block for lamp holder complete all as specified and as directed. 105 S&F in repairs LED lamp 9 Watt suitable for lamp holder fittings complete all as specified and as directed. 106 S&F in repair and testing of vertical type wall mounted storage water heater of Capacity 25 Ltrs BEE 5 Star rated or minimum Standing Loss of 0.511 kWh , 240V, 50Hz with Maximum power consumption of 2KW , dry powder fero glass line coating technologyfor inner tank with incoloy heating elementwith minimum4 years warranty , ABS outer body , 2 units of PVC connection pipe with length of 450mm length for hot and cold water supply with complete Accessories complete all as specified and as directed.Note:-Old wall mounted storage water heater shall be deposited to MES AGE(E/M) Store 107 S&F in repairs/replacement piano switch single pole 5A, one way complete all as specified and as directed. 108 S&F in repairs/replacement switch socket combination 2 in 1, 3 pin 5 A Flush complete all as specified and as directed. 109 S&F in repairs/replacement switch socket combination 2 in 1, 3 pin 5 A/16A Flush complete all as specified and as directed. 110 S&F in repairs/replacement socket outlet 5 pin 6A, 230 volt flush type complete all as specified and as directed. 111 S&F in repairs/replacement fan regulator 100/120 wall step type AC 220 volt complete all as specified and as directed. 112 S&F in repairs PVC switch board 10x12 suitable for switch socket complete all as specified and directed. 113 S&F in repairs PVC switch board 8x10 suitable for switch socket complete all as specified and directed. 114 S&F in repairs PVC switch board 8 x 6 suitable for switch socket complete all as specified and directed. 115 S&F in repairs PVC switch board 7x4 suitable for switch socket complete all as specified and directed. 116 S&F in repairs PVC switch board 4 x 4suitable for switch socket complete all as specified and directed. 117 S&F in replacement of PVC cassing & caping 25 mm complete all specified and as directed. 118 S&F in replacement of PVC cassing & caping 32 mm complete all specified and as directed. 119 M&L for replacement of PVC conduit 20mmcomplete all as specified and as directed. 120 M&L for replacement of PVC conduit 25mmcomplete all as specified and as directed. 121 S&F in repairs for engagement LED 0.5w light red, green, complete all as specified and as directed. 122 M&L for sub main wiring Casing capingtwo run 4.0 Sq mm and one run of 4.0 Sq mm for earth wire with multi standard copper conductors, 1100 volts grade, drawn throughand includingcasing caping complete all as specified and as directed. NOTE:- Two runs of 4.0 Sq mm +one run of 4.0 Sq mm and one run of PVC casing caping and its accessories of suitable size shall be measured as one unit length including taking down old unsv one complete all as specified and directed. 123 M&L for sub main wiring Casing capingtwo run 6.0 Sq mm and one run of 6.0 Sq mm for earth wire with multi standard copper conductors, 1100 volts grade, drawn throughand includingcasing caping complete all as specified and as directed. NOTE:- Two runs of 6.0 Sq mm +one run of 6.0 Sq mm and one run of PVC casing caping and its accessories of suitable size shall be measured as one unit length including taking down old unsv one complete all as specified and directed. 124 S&F in repairs MCB Distribution board double door type TPN 4 way, sheet steel, powder painted, with copper bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacitycomplete all as specified and as directed. 125 S&F in repairs MCB TPN 63 Amps, 415 volts, 50 Hz suitable for fixing in MCB DB C series complete all as specified and as directed. 126 S&F in repairsMCB Distribution board double door type SPN 8 way, sheet steel, powder painted, withneutral link & earth bar etc. and fixing MCBs of various rating capacitycomplete all as specified and as directed. 127 S&F in repairs/ReplacementMCB SPN 32 amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioningcomplete all as specified and as directed. 128 S&F in repairs MCB SPN 40 to 63 Amps, 230 volts, 50 Hz suitable for fixing in MCB DB C seriescomplete all as specified and as directed. 129 S&F in repairs MCB SP 5-32 Amps, 230 volts, 50 Hz suitable for fixing in MCB DB C seriescomplete all as specified and as directed. 130 S&F in repairs LED luminaire 600 mm x 600 mm, 35/36 watt, white/warm colour 220 AC recessed surfaced type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling and connecting up with driver, three core flexible copper conductor of suitable size complete all as specified and as directed. 131 S&F in repairs LED Bldg Security light fitting of capacity 25 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete with and including 1.2 mtr GI bracket of 25mm bore light grade bent to shape and fixed on wall with metal fastners 2 Nos 10mm dia incl drilling of holes as reqd and connecting up with flexible copper cable of size 0.75 sqmm 3 core from ceiling rose to the light fitting complete all as specified and as directed. 132 S&F in repairs globe light 8 dia made up of high grade unbrekable polycarbonate material suitable for retrofit LED lamp B22 including base holder bracket, MS pipe 40mm dia 1.5 mtrs long complete with 9 Watt LED Bulb and all accessoriesmaking good to the disturded surfaces by providing cement conrete M-15 (1:2:4) 20mm aggregate complete all as specified and as directed. 133 S&F in repairs LED Post of light 15 Watt, IP65 energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source Opal cover offers soothing uniform illumination for defferent applications all accessories complete all as specified and as directed. 134 S&F in repairs flexible copper wire 23/76 wire complete all as specified and as directed. 135 S&F in repairs PVC Exhaust fan PVC200 mm sweep single phase 50 Hz AC, air flow rate of1350 RPM including fixing on wall with suitale fastners, making holes of suitable size and making good distrubed surfaces areacomplete all as specified anddirected by Engr-in-Charge.Note : Old Exhaust fan shall be deposited to MES AGE(E/M) Store 136 S&F in repairs PVC Exhaust fan PVC250 mm sweep single phase 50 Hz AC, air flow rate of1350 RPM including fixing on wall with suitale fastners, making holes of suitable size and making good distrubed surfaces areacomplete all as specified anddirected by Engr-in-Charge.Note : Old Exhaust fan shall be deposited to MES AGE(E/M) Store 137 S&F in repairs PVC Exhaust fan PVC300 mm sweep single phase 50 Hz AC, air flow rate of1350 RPM including fixing on wall with suitale fastners, making holes of suitable size and making good distrubed surfaces area complete all as specified anddirected by Engr-in-Charge.Note : Old Exhaust fan shall be deposited to MES AGE(E/M) Store 138 Supply and fixing1100 volts grade heavy duty cable PVC insulated aluminium conductor, 6 Sqmm served with inner sheathing of PVC tape and overall PVC sheathed in service connectionsall as specified and directed incl taking down complete all as specified and directed by Engr-in-Charge.

BRR:7526073 tender for Certain Miscellaneous repair, i.e. Repair to plastering, tiling, painting etc in Community Centre -II, AA-IIC, New Town, Kolkata- Stripping off worn out plaster and raking out joints of walls,celings etc.up to any height and in any floor including removing rubbish within a lead of 75m as directed. 2 Plaster(towall, floor, ceilinge tc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding /staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](i) With 1:6 cement mortar 3 Rendering the Surface of walls and ceiling withWhite Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) 4 Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturers specification and as per direction of the EIC. (In Ground Floor) 5 Applying two coats of Acrylic Distemper toi nterior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturers specification) including cleaning and smoothning of surface. 6 Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. 7 Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc includ1ng using of approved puty elc. on the surface, if necessaryOn steel or other metal surface|With super gloss (hi-gloss)l(v) Two coats (with any shade except white) 8 Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20mm nominal size excluding shuttering and reinfor cement, if any, in ground floor as per relevant IS codes Pakur Variety 9 Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etcFloorWith Sand Cement Mortar (1:4) 20 mm thick & 2mm thick cement slurry at back side of tiles using cement @2.91 Kg /Sq.m & joint filling using white cement slurry @0.20kg /Sq.m.(a) Area of each tile upto 0.09 Sq.mOther than Coloured decorative inclfuding white 10 Resetting old glazed porcelain tiles in 20 mm thick cement mortar (1:4) including 4No sofkey stone(10mm) fixedwith adhesive of approved quality & 2 mm thick cement slurry using cement @2.91kg/Sq.mat the back of tiles and finishing joints with white cement & colouring oxide [if required] to match the colour of tiles over application slurry@1.75kg/ Sq.m below cement mortar including dismantling the old mortar etc 11 18mm. to22mm. thick, kota stone slab set in 20 mm thick (avg) cementmortar (1:4) in floor, stair & lobby including pointing in cement slurry with admixture of pigment matching the stone shade, including grinding &polishing as per direction of Engineer-in-charge to match with the existing work. [Slurry for bedding @4.4kg/ Sq.m and pointing @ 2.0 kg/ Sq.m] 12 Applying one coate of Exterior grade Acrylic primer in ground floorof approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured(matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturers specification and as per direction of the EIC. 13 Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturers specification and as per direction of EIC to be applied over acrylic primer as required The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.in Ground floor (Two Coat)

BRR:7525156 Tender For Construction Work Of Drain And Road From Furkan To Shiv Kumar Agrahari House. - Screping of old surface. 2 Earth work excavation in ordinary soil ncluding all complete. Sl No.251 3 Providing and laying 1:4:8 with cement concrete with cement, fine and and 40 mm brick ballast in the base. S.I 275 4 M-150 Brick work in 1:4 with cement coarse sand mortar including all complete. SI-307 5 Providing and laying 12 mm thick plaster in 1:3 with cement & coarse and mortar including all complete. Sl-582 6 P.C.C.1:2:4 with cement coarse sand and stone grite including all complete. SI No.-282 7 RCC 1:2:4 with cement, coarse sand and stone grite including all complete. SI No-284b 8 MS bars are provided in R.C.C. slabs Including all complete. Sl-504 9 Construction of granular sab-base by providing close graded material, mixing in a mechanical mix plant at OMC, carriage of mixed material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achive the desired complete as per clause 401 10 Providing laying spreading and compacting graded stone aggregate to wet mix macadam specification including premix the material with water at OMC in machanical mix plant carriage of mixed material by tipper site, laying in uniform layers with paver in sub-base/base course on well prepared surface and compacting with vibratory roller to achieve the desired density. Taking area 40.00% 11 Providing and applying primer coat with bitumen emulsion on prepared surface of granular base including clearing of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means broom complete as per as Clause 502 of MORTH Specification. 12 Providing and laying 50mm dense graded bituminous macadam with 100 TPH batch type HMP producing an average output of 75 tonne per hour using crushed aggregates of specified grading premixed with bituminous binder @ 4.0 to 4.5 percent by weight of total mix and filler, MORTH Specification clause 507 complete in all respects. 13 Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous surface cleaned with mechanical broom complete as per clause 503 of MORTH Specification. 14 Providing and laying 30 mm bituminous concrete with 60-90 TΡΗ batch type HMP producing an average output of 75 tonne per hour using crushed aggregates of specified grading premixed with bituminous binder @5.4 percent mix and fler, MORTH Specification clause 509 Complete in all respects. 15 Diposal of kachara/malba/unuseful excavated material from the site away from municipality area including all complete. 16 Construction of padustrial board 1.20X0.75m including all complete. 17 GST @ 18%

BRR:7524818 Tender For Periodical Services In Certain Buildings At Af Station Jaipur; 1 M&L for complete removal of existing treatment of wall including cornices surfaces by brooming down or steel wire brushing to remove of dust, dirt and loose scales of lime wash and other foreign material, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and applying two coats of cement based paint complete all as specified and directed. 2 M&L for Preparation of plastered or unplastered old decorated surfaces of wall including cornicesby brooming down or steel wire brushing to remove of dust, dirt and loose scales of lime wash and other foreign material, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and applying one coat of cement based paint complete all as specified and directed. 3 M&L for Preparation of plastered or unplastered old decorated surfaces of wall including cornicesby brooming down or steel wire brushing to remove of dust, dirt and loose scales of lime wash and other foreign material, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and applying two coats ofplastic emulsion paint on surfaces plain or moulded,over 10cm width or girthcomplete and as directed 4 M&L for complete removal of existing treatment of wall including cornices surfaces by brooming down or steel wire brushing to remove of dust, dirt and loose scales of lime wash and other foreign material, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and applying two coats ofdistemper oil emulsionover and including one coat of 3mm thick wall care putty and one coat of primer complete all as specified and directed. 5 M&L for Preparation of plastered or unplastered old decorated surfaces of wall including cornicesby brooming down or steel wire brushing to remove of dust, dirt and loose scales of lime wash and other foreign material, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spotsand applying one coat ofdistemper oil emulsioncomplete all as specified and directed. 6 Description all as peritem no. 5.00 here-in-before but one coat of oil distemper on ceiling surfaces. 7 M&L for Preparation of plastered or unplastered old decorated surfaces of wall including cornicesby brooming down or steel wire brushing to remove of dust, dirt and loose scales of lime wash and other foreign material, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and applying one coat of white wash complete all as specified and directed. 8 Description all as peritem no. 7.00 here-in-before but on ceiling surfaces. 9 M&L for Preparation of plastered or unplastered old decorated surfaces of wall including cornicesby brooming down or steel wire brushing to remove of dust, dirt and loose scales of lime wash and other foreign material, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spotsand applying one coat ofcolour wash on walls complete all as specified and directed. 10 M&L for preparing to old painted wooden surface of any description, exceeding 10cm in width or girth and applying one coat of sythetic enamel paint complete all as specified and directed. 11 M&L preparing to old painted steel surface of any description, exceeding 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 12 Taking down cement plaster on old brick or stone walls , including raking out joints, hacking for key, scrubbing down with water, etc. and replastering 15mm thick in cement mortar 1:6 complete all as specified and directed. 13 M&L for preparation to new plastered surfaces of walletc and applying two coats of oil bound distemper on walls over and including a coat of 3 mm thick wall care putty complete all as specified. 14 M&L for preparation to new plastered surfaces of wall and applying two coat of cement based paint complete all as specified and directed. 15 M&L for rubbing, grinding, cleaning, sweeping, washing and polishing of Dholpur stone at any surfaces (wall, wall cladding or floor) all as directed by Engineer-in-charge. 16 M&L for two coat of french polish on surfaces of any description, width or girth including cleaning and preparing the surface includingof wood filler on old works complete all as specified and directed. 17 M&L for Preparation of plastered or unplastered old decorated surfaces of wall including cornicesby brooming down or steel wire brushing to remove of dust, dirt and loose scales of lime wash and other foreign material, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spotsand applying two coat of Apex Ultima exterior weather proof paintof any shade complete all as specified and directed by Engg-in- charge. Note : Shade of paint will be decided by E-in Charge. 18 M&L for preparation of old surfacesof roof of any description and applying two coat of aluminium paint complete all as specified and directed. 19 M&L for rewriting or repainting letters and figures (Block, roman or italic or indian) not exc 30 cm height with synthetic enamel paint complete all as specified and directed. 20 M&L for rewriting or repainting Stops, commas, short lines, dashes, hyphens, brackets etc with synthetic enamel paint complete all as specified and directed.

BRR:7524663 6 Supply, Installation, Commissioning And Trial Operation Of Electro-Mechanical Components Of Baje Bindoli Water Supply Scheme Tw No. Ii In The District Of Uttar Dinajpur Under Malda Mechanical Division, Phe Dte.-1 Supply And Delivery At Site Of Following Pumping Machinery And Electrical Accrssories: 2 Submersible Pump Directly Coupled With Water Proof Suitable Size Motor Having Following Specification And As Per Nit Specification:Pumpdischarge Of Clear Water = ( Q ) = 28 M3 / Hr.Total Head ( H ) = 60 M.Shaft- Stainless Steelimpeller- S.S / Gmoutlet Size-80 Mmmotorsubmersible Type 3 Phase, 50 Hz, 415V ± 10% , 2900 Rpmmotor Mustbe Suitable For Operation With Star-Delta Starter This Item Will Be Procured Based On Yield Test Report Of T / W And Best Efiiciency Point As Per Direction Of Eic.Test Certificate Along With Characteristic Curve Shoule Besubmitted At The Time Of Delivery. 3 1.1 Kv Grade 4 Sq.Mm X 3 Core Water Proofflat Submersible Cable For Above Motor. 4 1.1 Kv Grade 25 Sqmm 3.5 Core Xlpe Insulated Al. Ar. Cable Cable Conforming To Is-7098 ( Part-1 ) 1988 With Upto Date Amendment. 5 Supply, Delivery And Storage At Site Of Wall Mounted 2 Mm. Thick Epoxy Painted Sheet Steel Enclosed Front Open Fully Panel For Fully Automatic Cum Manual Control Centre For Operation Of The Pump Motor In Star-Delta Mode Ranging From 7.5 Hp To 12.5 Hp, Actuator With Dol Starter, Chlorinator With Dol Starter And Timer Operated Outdoor And Indoor Lighting And Also Spares Feeder As Per Approved Drawingand Nit Specification. 6 Supply And Delivery Of The Following Valves, Pipes, Gauges Etc. At Site. 7 80 Mm Dia M.S. Seamless Column Pipe ( Black ) 6.8 Mm To 7.1 Mm Thick With 150 Mm Long Heavy Type Socket At One End. 8 3.00 Mtr. Long Excluding Socket Having 8 T.P.I. Thread. 9 1.5 Mtr. Long Excluding Socket One End Having A Thread Of 11 T.P.I. & The Other End Having A Thread Of 8 T.P.I. 10 Heavy Type Suitabledia Ms Suspension Clamp Along With Nuts Bolts And Washer. 11 Cast Iron Wafer Type Three Phase Actuator ( Rotork Range, Three Phase 415 V, Multiturn Electrically Actuated ) Operated Butterfly Valve Of Dia 80Mm ( P.N-1.0 ) As Per ( Is-13095 Ip-68 ) Test Certificates From Both The Manufacturer Are To Be Submitted At The Time Of Delivery 12 80Mm Dia Cidf Sluice Valve-1 No., Non Return Valve-1 No., Cidf 90° Bend-1No., Ci Flanged Tee-1No. Blank Flange-1No., Ci / Ms Flanged Short Piece 0.50 Mtr.-1 No, Ci / Ms Flanged Pipe 1 Mtr.-1 No. Etc As Per Is Specification And Certification For Construction Of Delivery Pipe Line And Wash Out Line. 13 Heavy Type 250 Mm Dia Split Type Tube Well Cover With 12 Mm Thick Clamping Arrangement Including Holes Of Column Pipe, Air Pipe And Cable Entry With 2 Sets Heavy Type Suspension Clump, Nuts, Bolts And Washer As Per Departmental Design. 14 Depth Gauge 100Mm Dia With Steel Air Pipe Of Required Length With All Accessories For The Above Work Including Supply Of Good Quality Hand Pump. ( This Cost Includes 15 Mm. Dia G.I. Pipes And Specials ) 15 Pressure Gauge ( H.Guru / Febig ) 150Mm Dia ( 0-7Kg / Sq.Cm ) Brass Cock And Fitting Complete. ( This Cost Includes 15 Mm. Dia G.I. Pipes And Specials ) 16 50 Mm. Dia. Non Metalic Pipes ( Is:14930 ) And Specials For Protection Of Submersible Cable ( As Per Site Requirement ) 17 Anti Snapping Safety Device For Pump Set By Supplying Suitable Size Ms Clamps Two Sets And Nylon Rope Of Required Length Including Supplying Of Nuts, Bolts And All Other Materials. 18 Supply And Delivery Of 100 Amps Male Female Kit Katfuse Unit 19 100 Amp 415 V Rewireable Type Tpn Main Switch. 20 Laying Of 25 Sq. Mm. 3.5 Core Al. Ar. Cable In Wall / Floor By Supplying Of All Necessary Materials As Per Ie Rules And As Per Direction 21 Installation Of The Materials ( To Be Supplied Under Above Sl No 1.01 To 3.11 ) Such As Pump Motor Set With Column Pipes, Valves, Panel, Fiting Fixing Pressure Gauge, Depth Gauge, Non-Return Valve & Drawing Delivery Out-Let & Washout Line With The Supplied Specials / Accessories By Providing Antisnapping Cage Of Suitable Size Including Supply Of Cable Gland, Sockets Etc Including Brick, Sand, Cement Rod Etc As Required To Complete The Job As Per Direction And Up To The Entire Satisfaction Of The Eic. 22 Making Brick Pillar 0.25 Mtr X 0.25 Mtr. For Supporting Of Valves And Pipes With 12 Mm Thick Plaster And Net Cement Finish Complete. 23 Supply, Delivery Of M.S Kiosk Box Of 661Mm X 559 Mm ( Lxw ) Size Having Thickness Of 1.5 Mm With Angle Support At Four Legs Having Hight Of 661 Mm With Provision Of Locking Arrangement, Supply Of Lock, Cable Entry Point Incl Painting By One Coat Of Black Paint Over One Coat Of Primer All Complete. 24 Making Suitable Size Pump Foundation Including Erection Of Kiosk Box With Supplying Of Necessary Cement, Sand And Stone Chips Including Plastering And Net Cement Finish Complete. 25 Making Double Earthing Arrangement In Compliance With Ie Rules By G.I. Pipe Electrode Of 50 Mm. Dia 3 Mtr. Long 2 Nos For Panel And Pumping Machinery 25 Mm. X 6 Mm. G.I. Earth Strips From Earth Pit To Panel And All Other Accessories Required To Complete The Work. 26 Making Internal Electrification Of Pump House Consisting Of Two Bracket Point, One Tube Light Point, Two Bulk Head Point, One Fan Point And 1 No. 74 Watt Led Fixture With Arm Bracket At Outside And One Three Pin Plug Point Including Supply Of All Necessary Materials To Complete The Work As Per Ie Rules And As Per Direction ( All The Fittings And Lamp Should Be Led Type As Per Choice Of Eic ) 27 Supply And Delivery Ofpvc Moulded Chair. 28 Supply And Delivery Of Pvc Moulded Table. 29 Supply, Delivery & Installation Of The Following Fan As Directed By Eic.Ceiling Fan 1200Mm Sweep Including Fan Clamp As And When Required. 30 Supply And Delivery At Site Of 15 Kva, 3 Phase Oil Cooledtype Servo Motor Operated Copper Wound Line Voltage Corrector Conforming To Is-9815 ( Pt.-1 ) -1994 Suitable For Un-Balanced Input Voltage Phase To Phase 200V.-500V Including First Filling Oil As Per Is-335 Where Applicable As Per Approved Drawingand Nit Specification. 31 Supply And Delivery Of Following Materials At Site: 32 100 Amps, 415 V, 4 Pole On Load Change Over Switch. 33 100 Amps, 415 V Tpn Rewireable Type Mainswitch. 34 100 Amps Bus-Bar Chamber Having 4 Nos. Al. Bus-Bar. 35 1.1 Kv Grade 415 V, 25 Sqmm, 3.5 Core Pvc Insulated 1.1 Kvaluminiumarmoured Cable. 36 Making Brick Built Foundation With Supplying Of All Required Materials Suitable For The Above Voltage Stabilizer By ( 4:1 ) Cement Mortar Including Holding Down Foundation Bolts And 12 Mm Thick Plaster With Neat Cement Finish, Sloping All Complete As Per Direction Of Eic. 37 Fitting , Fixing Of Change Over Switch, Busbar Chamber And Main Switch As Mentioned In Item No. 15.01, 15.02 And 15.03 On The Iron Angle Frame Of Suitable Size Fixed At Suitable Position On Wall By Supplying All Necessary Fixing Materials All Complete As Per Direction Of Eic. 38 Installation Of The Above Voltage Stabilizer As In Item No.14.00 On The Foundation Including Making All Connection Complete As Per Direction. 39 Drawing And Connection Of Cable As In Item No. 15.04 On Wall / Surface From Change Over To Panel Via Voltage Stabilizer, Bus Bar And Main Switch Incl. S & Fitting-Fixing Of Required Nos. Of Ms Saddles With Earthing Attachment In 10 Swg Gi ( Hot Dip ) Wire, Making Holes Etc. As Necy. Mending Good Damages And Painting. 40 Making Joints Of The Cable By Supplying Compresion Type Gland Thimple, Socket Etc. As Per Requirement And As Per Direction Of Eic. 41 Double Earthing The Whole Installations Complying With Ir Rules Including Supplying Of All Necessary Earthing Materilas For Voltage Corrector Device To Complete The Job As Per Direction Of Eic. 42 Supply & Delivery Of Automatically Controlleddiaphargm Type Chlorinator For Accurate Dosing Of Chlorine Solution Into The Waterby Connecting Metering Pump ( Diaphargm Type ) Having Following Specification:- Pump Type ::Diaphargmliquid ::Chlorine Solutioncapacity ( Lph ) :: 0-100Pressure Kg / Cm2 ( Testing ) :: 10Pressure Kg / Cm2 ( Suction ) :: Floodedpressure Kg / Cm2 ( Hydro ) :: 15Connection Suction :: ½” Hose Holderconnection Discharge :: ½: Hose Holdermoc Liquid End :: Ppdiaphragm :: Ptfenrv :: Ppdrive Capacity :: 0.5Hp, 3 Phase, 50Hz, 415V, 1440 Rpmmotorcoupling Capacity :: Flexible Spiderstrainer :: Y Type, Pp, ½” Bsp ( F ) Pressure Relief Valve :: Inbuilt.Solution Tank :: 100 Ltr Capacity ( Including Making Provision For Inlet Line To The Actual Storage Tank Of Dosing Solution Of All Materials. Test & Warrantycertificatesare To Be Submitted At The Time Of Delivery 43 Installation Of Above Supplied Chlorinator With All Accessories, Pvc Tankand Drawing Of Power Line As Per Ie Rules By Supplying Pvccopper Wire & Continuous Earthing. This Includes The Cost Of All Necessary Cc Foundation ( At Least 200Mm Height ) With Concrete Mixture ( Sand, Cement, Stone ) And Neat Cement Finish By Supplying Of All Required Materials And Testing The Entire Set As Perentire Satisfaction Of The Eic. ( Power Will Be Fed From Plc Panel Of Pumping Machinery ) 44 Commissioning Of The Installation With Full Satisfaction Of Eic And Trial Opearation, Maintenance, Guarding Of The Installation Round The Clock For A Period Of 90 ( Ninety ) Days From The Date Of Receipt Of Service Connection By Engaging Personnel Having Sufficient Experience In Electrical Installation. 45 Make As Per Departmental Approved Vendor List Circulated Vide Memo No.Phe / Iv / 2277 / W-181 / 19 Dated- 25 / 09 / 2019

BRR:7524306 Tender For Procurement Of 81Mm Mortar Plotter, Qty. - 05Nos.

BRR:7524302 Tender For Procurement Of 81Mm Mortar With Ces Items , Qty. - 07Nos.

BRR:7524295 Tender For Procurement Of 51 Mm Mortar Equipment With Ces Items Qty- 18 Nos.

BRR:7524114 Half Yearly Maintenance To Lalgarh Nts (Residential And Non-Residential Part) In The District Of Jhargram.- 1 Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately)For Exposed Work (PVC Pipe)20mm dia 2 25mm dia 3 32mm dia 4 40mm dia 5 Supplying, fitting and fixing shower of approved brand and make.Hand Shower(Health Faucet) with 1mtr Fexible Tube with Wall Hook(Equivalent to Code No.573 & Model -ALLIED of Jaquar or similar). 6 Supplying, fitting and fixing shower of approved brand and make.PTMT overhead shower ( Prayag or equivalent)150 mm round 7 Supplying, fitting and fixing bib cock or stop cock.Chromium plated angular Stop Cock with wall flange (Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar). 8 Supplying, fitting and fixing bib cock or stop cock.PTMT (Polytetra Bib Cock / Stop Cock ( Prayag or equivalent)15 mm 9 Supply of PVC pipes & fittings Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I)Socket (Dia) >> 20 mm 10 Socket (Dia) >> 25 mm 11 Socket (Dia) >> 32 mm 12 Socket (Dia) >> 40 mm 13 Elbow (Dia) >> 20 mm 14 Elbow (Dia) >> 25 mm 15 Elbow (Dia) >> 32 mm 16 Elbow (Dia) >> 40 mm 17 Tee (Dia) >> 20 mm 18 Tee (Dia) >> 25 mm 19 Tee (Dia) >> 32 mm 20 Tee (Dia) >> 40 mm 21 Nipple (75 mm long) (Dia) >> 20 mm 22 Nipple (75 mm long) (Dia) >> 25 mm 23 Nipple (75 mm long) (Dia) >> 40 mm 24 Union (Dia) >> 20 mm 25 Union (Dia) >> 32 mm 26 Union (Dia) >> 40 mm 27 Reducing Socket (mm X mm) >> 25 X 20 28 Reducing Socket (mm X mm) >> 40 X 25 29 Reducing Tee (mm X mm) >> 25 X 20 30 Reducing Tee (mm X mm) >> 40 X 25 31 Reducing Elbow (mm X mm) >> 25 X 20 32 Supply of Chlorinated Polyvinyl Chloride (CPVC) pipes & fittings conforming to IS-15778: 2007Ball Valve (Dia) >> 25 mm 33 Ball Valve (Dia) >> 40 mm 34 Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc. 35 Supplying, fitting and fixing concealed cistern of approved make with flash plate Cute/Loop/Shell/Nova (Code No. concealo-H(80mm Body sap code 508179 of Hindware or equivalent).Matt/Gloss 36 Changing the lather only of syphon of automatic cistern including taking out and refixing necessary parts. 37 Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint.630 mm X 450 mm size 38 Wash basin vitreous china of approved make (without fittings) supplied,fitted and fixed in position on 75mm X 75 mm X 75 mm wood blocks and C.I. brackets including two coats of painting of C.I. brackets.Surgeons wash basin 650 mm X 450 mm 39 Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia.750 mm long 40 Supplying,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps.900 mm long 41 Supplying, fitting and fixing pillar cock of approved make.PTMT Pillar Cock - 15 mm. (Prayag or equivalent). 42 CP Pillar Cock with 200 mm extended Lever Handle (Equivalent to Code No. 5031 & Model - FLORENTINE of JAQUAR or similar brand). 43 CP 2-way bib Cock - 15 mm, supplied, fitted and fixed. (Code No.5041 & Model - FLORENTINE of JAQUAR or similar brand). 44 Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc.With P trap 45 Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete.E.W.C.Plastic (hallow type) white 46 Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete.Polythene Flush Pipe 47 Dismantling Orissa pattern W.C. including taking out of base concrete, if necessary, complete. 48 Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer2000 litre capacity 49 Labour for hoisting plastic water storage tank.Above 1500 litre upto 5000 litre capacity.Upto 1st story from G.L. 50 Labour for hoisting plastic water storage tank.Above 1500 litre upto 5000 litre capacity.Extra for each additional story 51 Labour for lowering plastic water storage tank and stacking in places as directed.Above 1500 litre upto 5000 litre capacityFrom 1st story to G.L 52 Labour for lowering plastic water storage tank and stacking in places as directed.Above 1500 litre upto 5000 litre capacityExtra for each additional story 53 Labour for punching hole in plastic water storage tank upto 50 mm dia. 54 Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992Single Socketed 3 Meter Length >> 110 mm 55 Single Socketed 3 Meter Length >> 160 mm 56 Fitting >> Plain Tee >> 110 mm 57 Fitting >> Plain Tee >> 160 mm 58 Fitting >> Bend 87.50 >> 110 mm 59 Fitting >> Bend 87.50 >> 160 mm 60 Dismantling & Refixing pit cover 61 Cleaning silt of inspection pit. 62 Cleaning and disinfecting upto 2000 litre Water Tank including masonry reservoir 63 Removing chokage of water closet. 64 Repairing C.P. hinges of W.C. seat. 65 Refixing flush pipe/ M.S. bend/ C.P. flush pipe with I.R. adapter. 66 Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface]With 1:6 Cement Morter >> 20mm Thick 67 Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes.Pakur Variety 68 Labour for taking out door and window frame including shutter for repair or replacement of different parts of the frame & refixing the same including mending good all damaes complete. (Concrete and brick work for mending damage will be paid separately)Above area 2.5 Sq.m 69 Renewing iron mortice lock (local best approved quality) 6 lever with handle, connected rods and keys consisting a complete set:With chromium plated handle. 70 Taking out and refixing after oiling and cleaning including adjusting spring of different type of automatic door closer with necessary screw complete. 71 Taking out door and window shutters and rehanging the same with old fittings.With new iron screws 72 Labour charge for fabrication and installation of structuralGlazing/Curtain Wall made from annodized extruded allooy aluminium sections for the following units:-Structural Glazing made of extruded and annodized alloy aluminium sections, fabrications including cutting to proper shape and size, drilling including cost of brackets, fastener bolt, mullion bolt, nuts & washers, maskin tape, double side adhesieve crosslink foam (used for guard of glazed silicon on sub-frame), tissue paper foam (used as filler between sub-frame and under backing of weather silicon), screws and other necessary hardwares, fixing of glass as per drawing, specification and direction of Engineer-in-Charge. (The rate includes hire charges of all tools and plants, including all incidental charges, adhesieve, joiners such as screw,cleate angle,etc. but excluded the cost of extruded aluminium sections, glass, glazed silicon, weather silicon etc.) 73 Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987;clear, toughened glass conforming to IS: 2553-1992 (part-II)10mm thick 74 Supplying maruti lock (100mm) 75 Supplying PVC rollers for sliding windows as per direction of Engineer in charge. 76 Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987.5mm thick clear glass. 77 Iron socket bolt of approved quality fitted and fixed complete.225mm long x 10mm dia bolt. 78 Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting.200mm Long 79 Easing and oiling, cleaning collapsible gate and repairing tolocking arrangements. 80 Supplying, fitting & fixing fibre reinforced polymer (FRP) Composite door shutters as per approved design with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to satisfy IS:4020 door testing performance criteria. In ground floor.32 mm thick 81 Add : GST @18% (Eighteen Percent) on Rs.2,64,928.00 i.e. Total Amount over item No. 1 to 43 82 Add : Labour Welfare Cess @ 1 % (One Percent) on Rs.3,12,615.00 i.e. Total amount after GST over item No. 1 to 44

BRR:7523573 Renovation work of Arulmigu Arthanareeswarar Thirukoil, Elavanasurkottai, Ulundurpettai Tk , kallakurichi Dt- 1 Providing Scaffolding for vimanam raja gopuram with non flammebable materials wherever necessary for main form work and by providing coconut keeth as covering the areas & plat form for inspection etc all complete. 2 Vimanam / Gopuram upto 15’ - 0’ height 3 Vimanam / Gopuram upto 25’ - 0’ height 4 Gopurams upto 75’ - 0’ height 5 Dismantling Pressed Tiles & Weathering Course 6 Dismantling Lime Concrete 7 Labour charge for old stone removing 8 Pavukkal, 9 Uthiram 10 Bothiyal 11 Thun 12 Step 13 Ullvari 14 Flooring- i/s 15 Supply of cut stone for carrying out Garpagraham, Arthamandapam, Maha Mandapam, Thirumathil and other Temple Structures upto 10 feet length 16 Pavukkal, 17 Uthiram 18 Bothiyal 19 Labour charge for New stone dressing and Fixing 20 Pavukkal 21 Uthiram 22 Bothiyal 23 Labour charge for old stone dressing & Fixing 24 Flooring 25 Labour charge for old stone fixing 26 Pavukkal, 27 Uthiram 28 Bothiyal 29 Thun 30 Step 31 Ullvari 32 Scraping the decayed lime plaster from the surface of vimanam/gopuram. Care fully including isolated bricks or brick work without damaging the vari vargams, racking out the joints , cleaning the surface with water, including all working in heights-super ficial area including all folds -100 s.ft 33 Clean removal of lime plaster from walls, 34 Dismantling Plain Cement Concrete 35 Dismantling of Brick / Stone Masonry in lime mortar walls under 3m high 36 Brick work in Lime Mortar 1:2 mix using Countrybricks ( 83/4*41/4*23/4) includinglabour chagersetc complete complying the std specifications. 37 Abve basement 38 Brick work in Cement Mortar 1:5 mix using Countrybricks ( 83/4*41/4*23/4) includinglabour chagersetc complete complying the std specifications. 39 Providing vargapoochu over the core walls of vimanams/Gopurams,with Lime MORTAR 1:1.5 complete including Shaping the mukhapathram, mahanasi, koodu all ornamental works to proper shape by embedding broken bricks of shaped/chiseled bricks , rough plastering with Lime MORTAR 1:1.5and finshing with final ornamental plastering nayam theervani including cost and conveyance of all materials, labour there fore lifting of materials, all working in heights curing with water etc complete including all extra for folding and including clearingfrom the vimanams/gopurams 100 sft superficial area for kalkaram. 40 Vimanam 41 Plastering with Lime Mortar 1:1.5 mixto12mmthick including cost and conveyance of all materials to site and all labour charges etc 42 Plastering with cementMortar 1:3 mixto 10mmthick including cost and conveyance of all materials to site and all labour charges etc 43 Thorough scrapping of old plastered surface 44 Painting with multicolour (panchavarnam) good emulsion paints complete for the vimanams/gopurams,including cost and conveyance of all materials , labours charges including artist painter, working in heights, lifting of materials,cost of brushes etc, complete which including all extra for foldings 100 sft 45 Gopuram of ht upto 100-0 excluding kalkaram 46 Gopuram of ht upto 15-0 excluding kalkaram 47 Gopuram of ht upto 25-0 excluding kalkaram 48 Painting two Coats ExteriorEmulsion or egavarnam water Based painting Included cost of all materials and all labour charges etc,.complete as per stantard specification. 49 Weathering course with brick jelly lime concrete using 20mm brick jelly with pure slacked lime over R.C.C. roof slab in the proportion of 32:12.5 and well watering consolidatedwith wooden beaters to slop including cost and conveyance of materials to site and labour charges etc 50 Finising the top of the roof with one course of pressed tiles of size 20X20X2cm over a bed of Combination mortor 1:1:3 12mm thick mixed with water proof compound at 2% b weight ofcementincluding cost and conveyance of all materials to site and all labour charges etc 51 Restoration by providing herbal water wash and approrimats methodology to restore the originalities of the existing granite structure inclusive of hire charges scaffolding arrangements conveyance charges fortools & plants and machinaries to the workship spot and cleaning the site after completion of work etc 52 Pointing with Lime mortar 1:1.5 including all tools and plants and labour etc all complete for cut stone masonry. 53 Supply and fixing of TW Scantlings (for tiebeams & principal rafters) - Malabar 54 Earth work excavation and depositing on bank with in initial lead of 10 m and initial liftof 2m in hard stiff clay, stiff black cotton soil, hard red earth, earth mixed with small sized boulders and hard gravelly soil as per SS 20B 55 Supplying and Filling with foundation and basement with M sand in 15cm. Thick layerswell rammed & consolidated, including watering, complying with std.specification etc complete. 56 Paving with cut stone flooring using cut stone of size 600x600mm and 100mm thick and all the sides are machine cutting, top surface is neatly dressed and pointing with lime mortar 1:1.5 including all materials and labour charges.(Outer) 57 Supplying and fixing teak wood temple type door including all materials, labour charges for manufacturing and fixing I position including all furniture fittings etc complete with std specifications. 58 Painting two coats for new wood works such asothersimilarworksetc, completecomplying with std specification 59 Plain cement concrete 1:5:10 (One cement, five sand and ten hard broken granitestone jelly) using 40mm HBG metel as foundation concrete including dewatering wherever necessary and laid in layers of not more than 15cm. thick complying with std specification. 60 Providing and laying in position, Standardised Concrete Mix M20 Grade in accordance with IS 456:2000 using 20mm and down graded hard broken granite stone jelly for all rcc works with minimumm cement content 325Kg/m3 and maximum water cement ratio of 0.55, including admixture(plasticiser /super plasticiser) in recommanded proportions as per IS 9103 to acclerate, retard setting of concrete, improveworkability with out i paring strength and durability with about (5 cum) 7730 Kg of 20mm machine crushedstone jelly and with about (3.3 Cum) 5156 Kg of 10 12mm machine crushed stone jelly and with about (4.79cum) 7670 Kg of sand, but excluding cost of reinforcement grill and fabrication charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing etc and providing fixtures like fan clamps in RCC floor/ roof slabs wherver necessary without claming extra complete complying std specification and also directed by departmental officers. The coarse and fine aggregates to be used should comply with requirements of IS standard 61 A) for Sub structure 62 B) for Super structure 63 Centering for soffits of reinforced cement concrete slabs, plain surface including strutting 3 meter height using MS plates of size 90cmx60cm and 10 gauge stiffen and with welded mild steel angles of size 25x25x3mm laid over silver oak 64 A)For Basement 65 B)Column 66 Supplying ,Fabrication and placingin position of M.S. or RTS rods reforcement grill in position for all RCC works includingcost of steel rods and binding wire etc.,complete 67 Supplying and fixing MS grills to window and ventilator including the cost of necessary scrub and applying priming cost paint etc., complete. 68 Painting two coats for new iron works over the one coat of primer such as ironbarsflatsandothersimilarworksetc, completecomplying with std specification 69 Painting two coats for old iron works over the one coat of primer such as ironbarsflatsandothersimilarworksetc, completecomplying with std specification 70 Random Rubble Masonry work with Combination Mortar 1:1:5 mix using selected stones and rough stones in foundation and basement including dewatering wherever necessary proper setting,curing,etc., 71 Upto G.L 72 Supplying and fixing110mm dia P.V.C down fall pipe best and approved brand quality etc all complete as per standard and specifications. 73 Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in existingtrunking box on wall and ceiling with with Module GI switch box on wall with 6A one way module switch with module front plate with continuous earth wire connection by 1.5 sq.mm. PVC insulated SC unsheathed copper wireforLight point / fan point (for electronic regulator) ( 5 points / Coil) Higher End 74 Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with Module GI switch box on wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire withpainting of Suitable colour for Open PVC Light point / fan point (for electronic regulator) ( 5 points / Coil) Higher End 75 Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch on suitable module surface mounting Box (GI ) with module cover plate (plastic) on wall with connections. Higher End 76 Supply and fixing of single box type 1 x 20 W single LED fitting complete with TW round blocks on wall or ceiling with LED tube with PVC unsheathed Copper leads from terminals to the fitting. 77 Supply and fixing of fancy glass shade and 7W / 9W LED bulb 78 supply and fixing of 30W LED street light fitting with LED (Higher end) with 25 mm dia. GI pipe (class B) with 1 no. 25 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting 79 Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend completeWith S&F of Suitable AI frame on wall with PVC unsheathed copper leads with MS clampswith S&F of SMC box with 10 SPMCB (Higher end ) and with painting 80 Supply and fixing of 3nos.6A two module 5 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End 81 Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch on suitable module surface mounting Box (GI ) with module cover plate (plastic) on wall with connections. Higher End 82 Supply and run of 35mm x 20mm powder coated duct with door arrangements complete with MS angle and bolt & nuts comple. 83 Supply and run of 35mm x 45mm powder coated duct with door arrangements complete with MS angle and bolt & nuts comple. 84 Supply and run of MS flat for clamps of size 2 x 1 on pillar with suitable Bolt / nuts and painting of suitable colour. 85 Supply and Run of 2 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in the existing duting with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire 86 Supply and Run of 2 of 4 sq.mm. (56/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in the existing duting with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire . 87 Supply and clamping of 4 x 2.5 sq.mm PVC LTUG armoured copper cable in on post or on wall with MS Clamps. 88 Supply and laying of 4 x 2.5 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good 89 Supply and laying of 4 x 16 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good 90 Supply and clamping of 4 x 16 sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps. 91 Supply and laying of 31/2x 35 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good 92 Supply and clamping of 31/2 x35 sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps. 93 Supply and fixing of brass cable gland for 4 x 25 (16 )sqmm PVC armoured LTUG cable with earth connection. 94 Supply and fixing of brass cable gland for 31/2 x 35 sqmm PVC armoured LTUG cable with earth connection. 95 Supply and providing cable end termination of 4 x 16 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete 96 Supply and providing cable end termination of 31/2 x 35 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete 97 Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 40A DP MCB Isolator as incoming and 6 nos. 6A to 32A SP MCB as outgoing on suitable angle iron frame on wall with earth connection only. Higher End 98 Supply and fixing of 6 way Horizontal Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 18 nos. 6A to 32A SP MCB as outgoing on suitable angle iron frame on wall with earth connection only. Higher End 99 Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 100 A 4P MCB Isolator as incoming and 3 nos.32A 3P MCB , 15 nos. 6A to 32A SP MCB as outgoing on suitable angle iron frame on wall with earth connection only. Higher End 100 Supply and fixing of 40A phase selector switch on sheet steel enclosure box with indicator lamps and electrical connections complete. 101 Supply and Run of 4 of 16 sq.mm (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade on 7/20 GI wire for service connection mains 102 Supply and Run of 4 of 16 sq.mm (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in 25mm dia GI pipe (class B ) suitably bent at both ends with necessary angle iron upright and end support for service connection mains 103 Supply and fixing of powder coated box on wall fabricated with MS sheet of 16 gauge of size 900mm x 300mm x 450mm with 3 nos. of 100A (500V) porcelain fuse units, 1 no. of 100A TPN sheet steel double break switch with HRC Fuse units provision for fixing TNEB meter with electrical connections complete 104 Supply and fixing of 100 A Three phase 500V 4 Pole Change over Switch on suitable angle iron frame workwith MS cable entry boxes with earth connection only 105 Supply and fixing of 32A DP MCB in sheet steel enclosure box with electrical connections complete. 106 Earthing as per the PWD standard with an earth electrode of 2mt class B GI pipe of dia not less than 32mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry. 107 Supply and Run of 1 of No.8 SWG Copperwire in suitable PVC rigid pipe on wall / floor / ground for earth connection 108 sub total 109 GST 18%

BRR:7522478 Tender For Construction Of 10Nos Fire Wall, Cable Trench And Other Associated Civil Works At Various 33/11Kv Sub-Stations Under Edc-Orai, Distt. Jalaun, 1 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge. All kinds of soil (DSR No.2.6.1) 2 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.(DSR No. 2.8.1) 3 Concrete with 4 cm gauge brick ballast obtained from breaking brick bats (brick bats supplied by the department free of cost) in proportion of 12:6:1 in foundation and under floors and supply of all materials, labour, and T&P etc. required for proper completion of work (NSI) 4 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : (DSR No. 4.1.) 1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)(DSR No. 4.1.3) 5 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : (DSR No. 4.1.) 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources). (DSR No. 4.1.8) 6 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : (DSR No. 5.1) 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) (DSR No. 5.1.2) 7 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :(DSR No. 5.2) 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)(DSR No. 5.2.2) 8 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources). (DSR No. 5.3) 9 Centering and shuttering including strutting, propping etc. and removal of form forFoundations, footings, bases of columns, etc. for mass concrete. (DSR 5.9.1) 10 Centering and shuttering including strutting, propping etc. and removal of form forlintels, beams, plinth beams, girders, bressumers and cantilevers. (DSR 5.9.5) 11 Centering and shuttering including strutting, propping etc. and removal of form forcolums, pillars, piers, abutments, posts and struts. (DSR 5.9.6) 12 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. (DSR No. 5.22A) Thermo-Mechanically Treated bars of grade Fe-500D or more. (DSR No. 5.22A.6) 13 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections(DSR No. 5.30) 14 Brick work with common burnt clay F.P.S (Non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) (DSR No. 6.1.1) 15 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) (DSR No. 6.1.2) 16 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : (DSR No. 6.4) Cement mortar 1:4 (1 cement : 4 coarse sand) (DSR No. 6.4.1) 17 Brick work in foundation & plinth with old dismantledbricks (supplied by department free of cost) and coarse sand mortar in 1:6 including supply of all other materials, labour, removing mortar & cleaning of old & used bricks,T&P etc complete.(CSI No. 6.18) 18 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoising, fixingh in postion and applying a priming coat of approved steel primer all complete. (DSR No. 10.2) 19 Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with sand, with common burnt clay non modular bricks.(DSR No. 11.2) 20 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. (DSR No. 11.3)40 mm thick with 20 mm nominal size stone aggregate (DSR No. 11.3.1) 21 12 mm cement plaster of mix : (DSR No. 13.4) 1:4 (1 cement: 4 coarse sand) (DSR No. 13.4.1) 22 Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. (DSR No. 15.3) 23 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.. (DSR No. 15.7) In cement mortar (DSR No. 15.7.4) 24 Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured): (DSR No. 15.8) From brick work in cement mortar (DSR No. 15.8.3) 25 Finishing walls with water proof exterior emulsion paint ofACE (ASIAN) or equivalent brand on already well prepared new wall surfaces with one coat of primer (ICI) followed by two coats of ACE exterior empulsion paint to give an even shade including thorough washing with water including as per direction of E/I direction of including cost of all materials, labour, T&P etc requried for proper completion of the work (NSI)

BRR:7522382 Tender For Construction Of Lomar To Chakla Link Road Including 5 Year Maintenace - Construction of embankment with approved material obtained from borrow pits with a lift up to 1.5 meter transporting to sites spreading grading to require slope and compaction to meet requirement of table 300.1 & 300.2 with a lead up to 50 meter as per MORD technical specification cause 301.5 MORD sepecification 301.5(i) S.No. 3.4 2 Construction of Subgrade with Stablization of Soil with 2% slaked limeConstruction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads. transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead up to 1000 m as per Technical specification cause 303.1. including Stablization with 2% staked lime including its mixing with rotabator complete. 3 Providing, Laying and spreading material on a prepared sub grade, adding cement @ 2% by weight of the spread material manually mixing in place with rotavator and compacting with the road roller at OMC to achive the desired unconfined compressive strength and to form a layer of sub base. 4 Providing, Laying and spreading material on a prepared sub grade, adding cement @ 4% by weight of the spread material manually mixing in place with rotavator and compacting with the road roller at OMC to achive the desired unconfined compressive strength and to form a layer of sub base. 5 Providing and applying tack coat with V.G.-10 bitumen using bitumen pressure dristributor @ 0.35kg. per sqm. on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503. 6 Providinglaying & rolling of open graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line ,grade and level to serve as wearing course on a previously prepared base including mixing in a suitable plant,laying and rolling with a three wheel 80-100 KN static roller capacity finished to required level and grades to be followed by seal coat . Claues 508 7 Providing and laying seal coat Type-C sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using As per Technical Specification Clause 510 8 Construction of Earthen Shoulders with Stablization of Soil with 2% slaked limeConstruction of embankment in stablized Soulder with approved material obtained from borrow pits with a lift up to 1.5 meter transporting to sites spreading grading to require slope and compaction to meet requirement of table 300.1 & 300.2 with a lead up to 50 meter as per MORD technical specification cause 301.5 MORD sepecification 301.5(i) S.No. 3.4 9 Excavation in foundation in B.C soil including lift up to 15 meterand lead upto 30 m (100 ft) and including filling, watering & ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the Engineer-in-charge upto a distance of 30 Mfrom the foundation trenches.(S.I.No. 251) 10 Sand filling in plinth including supply of necessaryquantityof sandfrom adistance not exceeding 8 Kmfrom the site of work & including watering, dressing etc. Rate to include cost of all materials, labour and tools & plants etc. required for proper completion of the work. (S.I.No. 255) 11 Cement concrete with 4cm (1/2) gauge approved stone ballast, approved coarse sand. cement in the proportion 1 : 4 : 8 including supply of all materials,labour and tools and plants etc. required for proper completion of the work. As per S.I. No.-281 12 Providing and laying 1000mm dia reinforced concrete pipe NP3 in single row for culverts on Type A (Concrete cradle) bedding with M 15 grade cement concrete including fixing coller with cement mortar 1:2 but excuding excavation protrction work, backfilling, concrete and masonary works in head walls and parapets clause 1106 as per Data Book item No. 9.3 (B) 13 S & Laying in the Hume pipewith collars in positionwith cement and sandmortarin 1:2 withsunincluding labour and T & P etc. required for proper completion of work as per direction ofby the Engineer-in-charge N.P-3-Type(a) 600 mm dia 14 Supply & Laying cement concrete pipe NP-3 350 mm dia (burried Conduits) on first calss bedding of granular material including fixing collar with cement sand mortar 1:2 but excluding excavation protection works, backfilling. concrete and masonary work in head wall and parapoets as per MORD specification no. 1100 sr no. 9.7 as per Data book item no. 9.70 15 Class-150 brick work in 1:4 cement and fine sand of 1.25 fineness modulus mortar in foundation and plinth including supply of all materials, labour and tools and plants etc. Required for proper completion of the work. 16 12mm thick plaster on brick work minimum thickness not less than 10mm with 1part of cement and 4 part of find sand of 1.25 fineness modulus. As per SI. No.-584 17 Cement concrete with 20mm (1/2) gauge approved stone ballast, approved coarse sand. cement in the proportion 4:2:1 including supply of all materials,labour and tools and plants etc. required for proper completion of the work. As per S.I. 279(a). 18 Maintenance of Bituminous Surface Road and gravel of WBM road including filling pot hols and patch repair etc. restroration of rain cuts and dressing of side slop / berms making up of berms / shoulders maintenance of drain, maintenance of culvert, maintenance of guard rails and parapet, maintenance of road sign, speed breakers standing tree at adjacent of road wherever required maintenance of 200m stone (Hectometre) and kilometer stones, cutting of branches of trees, shrub and trimming of glass and weeds etc while washing of parapet including CD work, paiting of guard stones, refixing of displaced gaurd stone (As per Performance index Annexure-1) mentioned in GO No-17/2024/ sa-113/23-1-2024-23-1099/113 /2023 dated 16-01-2024 & E-in-C Letter No-3689/C-OPRMC / MUL-2023-24 dated 17-02-2024 subjected to approval from Govt. Maintenance of 1st Year after completion of work @ 0% of total cost of PC Work 19 Maintenance cost for 2nd Year @ 1.50% cost of PC Work 20 Maintenance cost for 3rd Year @ 3.00% cost of PC Work 21 Maintenance cost for 4th Year @ 4.50% cost of PC Work 22 Maintenance cost for 5th Year @ 6.00% cost of PC Work

BRR:7522292 Tender For Construction work of the entire connecting road from Devpur Bahadurs Purva turn to Sanhai - Earth work in embankment in ordinary soil including lift upto 1.50 mtr. and lead up to 30.00 mtr. and also including ramming dressing the surface to required level and slope as per direction ofE/I. 2 Earth work in excavation in trench for foundation in ordinary soil i/c lift upto 1.50 mtr. & lead upto 50.00 mtr. And dressing of sides and ramming of bottom and disposal of surplus excavated earth as directed bu the E/I within a distance of 50 m. 3 Construction of granular sub-base by providing Well graded material Grading-1, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with Smooth wheel roller to achieve the desired density, complete as per technical clause 401 4 Providing, laying, spreading and compacting stone aggregates of 45-63 mm sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with Smooth wheel roller 80-100 kn in stages to proper grade and camber, applying and brooming crushable Stone dust to fill up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per Technical Specification Clause 405. 5 Providing, laying, spreading and compacting stone aggregates of 22.4-53 mm sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with Smooth wheel roller 80-100 kn in stages to proper grade and camber, applying and brooming stone dust to fill up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per Technical Specification Clause 405. 6 Brick edging 7 cm wide on both sides of the road by S.O. Bricks complete as per PWD detailed specification no 20.15 7 Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means as per Technical Specification Clause 502 8 Providing and applying tack coat with Bitumen using distributor at the rate of 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503. 9 Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 KN static roller capacity, finished to required level and grades to be followed by seal coat Type C as per Technical Specification Clause 508. 10 Providing and laying seal coatby manual means with VG-10 bitumen sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type Cas per Technical Specification Clause 510 11 Earth work in Both side Patri.in ordinary soil including lift upto 1.50 mtr. and lead up to 30.00 mtr. and also including ramming dressing the surface to required level and slope as per direction ofE/I. 12 Providing & laying in cement concerete 1:3:6( 1 cement : 3 Coarse sand : 6 Stone aggregate 40 mm.nominal size) and curing complete, including supply of all materials, labour and T&P etc. required for proper completion of work as per direction of E/ 13 Class-150 brick work in 1:4cement and coarse sand mortar in foundation and plinth i/c supply of all material, labour, curing and tools and plants etc. required for proper completion of the work. 14 Struck pointing on brick work in 1:2 cement mortar (1 cement & 2 fine sand) including supply of all material, labour and T&P etc. required for proper completion of work 15 Providing and laying of Hume pipe 900mm i/c cartage 16 Providing and laying of Hume pipe 350mm i/c cartage 17 E/W In embankment in ordinary soil for Cushion 18 Providing & fixing Sign board, km stone, Hectometer Stone & Letter writting work complete. 19 The routine maintenance of above road work including earthen shoulder, and bitumenous pavement etc to the required standards and in the manner as defined in CB Condition and keep the entire road surface and structure in Defect free condition during the entire maintenance period which begins from the actual Completion Date and ends after five years.(including cost of material T&P labour but excluding GST) 1St Year Maintenance Cost @ Charge - 0.00% (Total Cost of Item nos. 1 to 15) 20 The routine maintenance of above road work including earthen shoulder, and bitumenous pavement etc to the required standards and in the manner as defined in CB Condition and keep the entire road surface and structure in Defect free condition during the entire maintenance period wwhhiicchh bbeeggiinnss ffrroomm tthhee aaccttuuaall CCoommpplleettiioonn DDaattee aanndd ends after five years.(including cost of material T&P labour but excluding GST) 2nd Year Maintenance Cost @ 0.75% (Total Cost of Item nos. 1 to 15) 21 The routine maintenance of above road work including earthen shoulder, and bituminous pavement etc to the required standards and in the manner as defined in CB Condition and keep the entire road surface and structure in Defect free condition during the entire maintenance period which begins from the actual Completion Date and ends after five years.(including cost of material T&P labour but excluding GST) 3rd Year Maintenance Cost @ 1.50% (Total Cost of Item nos. 1 to 15) 22 The routine maintenance of above road work including earthen shoulder, and bituminous pavement etc to the required standards and in the manner as defined in CB Condition and keep the entire road surface and structure in Defect free condition during the entire maintenance period which begins from the actual Completion Date and ends after five years.(including cost of material T&P labour but excluding GST) 4th Year Maintenance Cost @ 2.25% (Total Cost of Item nos. 1 to 15) 23 The routine maintenance of above road work including earthen shoulder, and bitumenous pavement etc to the required standards and in the manner as defined in CB Condition and keep the entire road surface and structure in Defect free condition during the entire maintenance period wwhhiicchh bbeeggiinnss ffrroomm tthhee aaccttuuaall CCoommpplleettiioonn DDaattee aanndd ends after five years.(including cost of material T&P labour but excluding GST) 5th Year Maintenance Cost @ 3.00% (Total Cost of Item nos. 1 to 15)

BRR:7522201 Tender For Rain water harvesting construction work (as per estimate rate 1 harvesting total 10 harvesting) - Earth work in foundation or embankment in ordinary soil including eath from 5 km to the site Chap 04 sr no 251 3 M150 Brick work in 1:4 cement and coarse sand mortar including all cost of materials, labour and T&P etc required for proper completion of work. (S.I. No. 305) 4 PCC 1:2:4 with cement coarse sand & 20 mm guage stone grit including labour material T&P incl all compl. 5 RCC work 1:1:5:4 with cement approved coarse sand & 20 mm gauge stone grit etc. including centering & shuttering etc. all compl. of work S.I. No. 283A 6 Supply and Filling of 2nd Class brick ballast as in soackpits etc sor page 3 7 Supply and fixing of 10 cm dia a.c. down pipe make complte with bands nuts bolts including proper completion of work 730A 8 Mild steel or iron work in plain work such as R.C.C. or R.B. wrok including bending for proper shape and including supply of steel and its wastage & authorised overlapping etc. shall be measured. (S.I. No. 504) 9 Silt Ejector 10 Boring/Driling bore well of required dia for rain water harvesting soak pit incluidng 150 mm slotted pipe 10 mm deep, all cost of material, labour & T&P etc complete (As per CPWD SOR VOL-2 CH-23 ITEM 23.1.1.1)

BRR:7522074 Tender For Work of tiling the entire house, renovation of one bathroom and covering the balcony with mesh in house number A-102, Government Colony 17A, Mall Avenue - Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm DAR NO-15.23.1 2 Providing & fixingMS Welded mesh jalli with 25x5 mm flat iron includung suply of all maiterial labour T&P etc complete aperture on both sides 3 structural steel work riveted , bolted or welded in built up sections , trusses and framed work , including cutting . Hosting fixing in postion and applying a primimg coat of approved steel all complete. (dar-10.2) 4 Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes , having thermal stability for hot & cold water supply , including all CPVC plain & threaded fittings , i/c fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipe & fitting with one step CPVC solvent cement and cost of cutting chases and making good the same including testing of pipes complete as per direction of Engineer - in - charge , concealed work . including cutting chases and making good the walls etc (20 mm nominal outer dia pipe )18.8.2 5 Providing and fixing PVC pipes (6kg/sqcm) for sewer line including all fitting including trenching refilling & testing of joints complete as per direction of Engineer in charge110 mm dia . 6 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.(dar-11.38) 7 Providing and fixing 1st quality ceramic, glazed wall tiles conforming to IS 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green black of any size as approved by Engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thck bed of cmeent mortar 1:3 ( 1 cement 3 coarse sand) and jointing with grey cmeent slurry @ 3.3 kg per sqm, including pointign in white cement mixed with pigment of matching shade complete.DAR NO-8.31 8 Providing and laying vitrufied floor tile in different sizes ( thickness to be specified by the manufacturer)with water absorption less than 0.08% and comferming to IS :15622 , of approved make in all colour and shade , laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand ) jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigment etc complete(ch-13- ref- 11.41.2) ( size of tile 600x600 mm ) 9 Providing and fixing C.P. brass angle valve l&Kfor basin mixer and geyser points of approved quality 15 mm nominal bore. 10 Providing and fixing C.P. brass wall mixture with tele phonic shower 3 in 1 (L&K make code 0457 ) or Equivalentquality. 11 Providing and fixing C.P. brass center hole basin mixture oF EquivalentqualityL& K Make 12 Supply and Fixing C.P. brass bib cock 15mm. dia. Long body L&K 0047 including supply of all materials, labour, T&P etc. required for proper completion of the work. 13 Providing and fixing galss corner Equivalent make including supply of all material, labour T&P etc. complete. 14 Providing and fixing of glass shelf 22L&K make with C.P. Guard standard size and bracket including supply of all material labour T&P required for proper completion of the work. 15 Providing and fixing C.P. brass OVER HEADshower with arm heavy qualityL&K 0668 with 15mm inlet: 150 mm diameter 16 Providing and fixing C.P. Brass Two way bibcock heavy code No-0257 L&K or Equivalent make including supply of all material, labour T&P etc. complete. 17 Supply and fixing C.P. Health Faucet with 8mm Dia 1.00 mtr. Long Flexible tube & wall hook L&K Make including supply of all material, labour T&P etc. complete. 18 Providing and fixing CP towel Rod OF L&K Make 600x20mm together with pair of CP brass brackets to fit the towel rail complete. 19 Providing and fixing CP towelring L & K or equivelent fittings arrangement of approved quality. 20 Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge .Sutra C8965 (S-220) (680 x 360 x 710mm) 21 Supply and fixing of white glazed earthen ware Wash Hand Basin with pedestal ( 550x430x195 mm Qubax ) with C.P Waste jali,, pvc waste pipe,including supply of all materials labour T&P etc. required for proper completion of the work.

BRR:7522042 Tender For Construction Of A Shed For Condolence Meeting At Muktidham In Ramrai River Gadiyagaon Jhansi - Clearing jungle including up rooting of trunk vegetation grass bush wood trees and sapling of girth upto 30cm. Measured at a height of 1 meter above ground level and removal of rubbish upto a distance of 50m. outside the periphery of area cleared. 2 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil 3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-lll) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) 4 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level in :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) 5 Brick work with common burnt clay (non modular) bricks of class -150in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand) 6 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand (zone-lll) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) Above Plinth Lvl T-Beam 7 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand (zone-lll) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) Above Plinth Lvl Slab 8 Steel reinforcement for R.C.C. work ready to use cut and bend rebars of approved make from factory/workshop to construction site including placing in position and binding all complete in Thermo-Mechanically Treated bars of grade Fe-500D or more. 9 Brick work with common burnt clay bricks of M-150 Class in super structure above plinth level upto floor V level in all shapes and sizes in cement mortar 1:6 ( 1 cement : 6 coarse sand ) 10 12 mm thick cement plaster of mix 1:6 ( 1 cement & 6 course sand ) including supply of all materials, labours and T&P etc. required for proper completion of the work. 11 P.C.C. with 20 mm Stone grid base of cement mortar 1:2:4 including supply of all materials, labours and T&P etc. required for proper completion of the work. 12 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) 13 Providing and applying white cement based Putty of average thickness 1 mm of approved brand and manufacturer,over the plasterd wall surface even and smooth surface. 14 P/L 20 mm thick kota stone flooring over 20 mm thick base of cement mortar 1:4 including supply of all materials, labours and T&P etc. required for proper completion of the work . 15 S/F of RCC Bench at Site (3 Seater) 16 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 17 Supply and fixing of sing board including painting and lettering as directed by Engineer-in-charge.

BRR:7520056 Tender For Addn/Altn To Certain Omqs And Smqs At Chaf Bangalore; 1 SCHEDULE A PART - I (B/R Portion)Demolition of Stone slabs and tiles laid bedded and pointed in cement mortar of any description or thickness in floors, aprons etc complete all as specified and directed. 2 Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided forall as specified and as directed 3 Dismantling floor hearth or wall tiling including cement mortar bedding andbacking coat plastering of any thickness removing serviceable tiles to store and rubbish off premises etc complete all as specified and as directed. 4 Taking down cement or cement lime plaster any description on brick or stone walls, over RCC slab ,ceiling etc includingraking out joints, hacking for key, scrubbing down with water, etc.including necessary scaffolding complete all as specified and directed. 5 Material and labour forVitrified Ceramic tiles 10 mm thick, double charged (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over 15mm thick screed bed or bedding in CM 1:4 complete all as specified and directed. 6 All as per Item No. 5 here-in before, but in Skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over 10mm thick screed bed or bedding in CM 1:3 complete all as specified and directed. 7 Material and labour for Non - skid Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15mm thick screed bed or bedding in CM 1:4 complete all as specified and directed. 8 All as per Item No. 7 here-in before, but in Skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over 10mm thick screed bed or bedding in CM 1:3 complete all as specified and directed. 9 Material and labour for Non - skid Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15mm thick screed bed or bedding in CM 1:3 complete all as specified and directed. 10 Material and labour for glazed ceramic tiles coloured of size350x 250x 7 mm/ 450X 350X 7mm thickas vertical surface set and jointed in neat cement slurry and pointed in white or colour cement mixed with pigment to match the shade of the tiles complete all as specified and as directed with 10 mm thick rendering in cement mortar 1:3 for laying wall finishes complete all as specified and as directed. 11 Material and labour for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stoneincluding the like laid overcement mortar 1:4, 20 mm thick set and jointed in neat cement slurry and pointed in white cement with pigment to matchincluding grinding and polishing complete all as specified and as directed. 12 Material and labour for rounding to edges of granite/stone slab such as in steps, cooking platform and other similar situations etc complete all as specified and as directed by Engr-In-Charge. 13 Material and labour for 100 mm thick Cement concrete type B- 2, 1:2:4 (40mm graded stone aggregate)in floor finishes and paving and finishing cement concrete surface even and smooth Without usingextra cement complete all as specified and as directed. 14 Material and labour for rendering 15 mm thick on fair faces of brick works/ block works or concrete surfaces cement plaster 1:4 finished even and smooth without using extra cement all as directed. all as specified and as directed. 15 Material and labour for rendering 15 mm thick on fair faces of brick works/ block works or concrete surfaces cement plaster 1:6 finished even and smooth without using extra cement all as directed. all as specified and as directed. 16 Material and labour for rendering 5 mm thick cement plaster in cement mortar 1:3,on concrete surfaces as in ceiling/ chajja , finished even and smooth without using extra cement. 17 Material and labour for preparing new plastered surface of walls and applying two coats of cement base paint over a coat of primerthrough mechanical meanscomplete all as specified and as directed 18 Material and labour for preparing new plastered surfaces of wall and applying three coats of white wash complete all as specified and as directed. 19 Material and labour for preparing new plastered on wall and applying two coats of oil bound distemper over a coat of chalk whitening complete all as specified and directed by Engr-In-Charge. 20 Material and labour for preparing new plastered on ceilingand applying three coats of white wash complete all as specified and as directed. 21 Material and labour for preparing new plastered surface on ceiling and applying two coats of distemper over a coat of chalk whitening complete all as specified and directed 22 Supply and fixRotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), triple layered, hoisted & fixed in position all as specified in SSR Part I , 500 Ltrs Capacity including dismantling existing 500 Ltr water tanks complete all as specified and as directed. 23 Supply and fix in repair ballvalves, 25 mm diabore high pressure, of PTMT with epoxy coated Aluminium rod&high density plastic ball screwed for iron pipe and fixed. 24 Supply and fix in repairs 25 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed. 25 Supply and fix 25 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed. 26 Supply and fix in repairstainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe , cast iron cantilever bracket , connecting union overall size 915mmX460mm with bowl size 410mm X 330mmX160mm complete all as specified and directed. 27 Supply and fix tubing, medium grade,15mm bore with all fittings fixed to walls and ceiling or laid in floors including cutting through walls and floors etc and their making good complete all as specified and directed. 28 Supply and fix tubing, medium grade,20mm bore with all fittings fixed to walls and ceiling or laid in floors including cutting through walls and floors etc and their making good complete all as specified and directed. 29 Supply and fix tubing, medium grade,25mm bore with all fittings fixed to walls and ceiling or laid in floors including cutting through walls and floors etc and their making good complete all as specified and directed. 30 Demolition of unreinforced cement concrete in floors and pavings not exc 15cm thick below or above ground level complete all as specified and as directed. 31 Material and labour for 75mm thick cement concretetype C-2, 1:3:6 (40 mm graded aggregate) as in plinth protection all as specified and directed. 32 Material and labour for providing cement concrete type B-0 (1:2:4) using 12.5 mm graded aggregate as , in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, necessary form work allas specified and directed. 33 Supply and fix in repairs vitreous China wash basin, white flat back, size 550x400mm including cutting for and pinning in ends of brackets or erecting stand, etc complete all as specified and directed. 34 Supply and fix in repairs 15mm pillar tap,cast copper alloy, with capstan head, chromium plated, fancy type screwed down high pressure, with or without lettered hot or cold with long screwed shank and fly nuts screwed for iron pipe of 15mm bore complete all as specified and as directed. 35 Supply and fix in repairs vitreous china squatting pan Orissa pattern of size 580 X 440mm white with integral foot rest P trap including connection to trap and flush pipe anti-syphonage pipe etc complete including making good to floor all as specified and as directed. 36 Supply and fix in repairs Vitreous China wash down watercloset pan (Pedestal Pattern), White with P or S trap, including provision of fixing bolts and connecting upto drain and flushing pipe etc. complete all as specified and as directed. 37 Supply and fix in repairs plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed. 38 Supply and fix in repairs PVC flushing cistern with flush out valve type,10 ltrs capacity, low level white with inlet ball valve, float and handle including bracket including flush pipe complete all as specified and as directed. 39 Supply and fix in repair PVC connection pipe 450mm long 15mm dia both end having brass coupling nut and PVC washer complete all as specified and directed 40 Supply and fixPVC connection pipe 450mm long 15mm dia both end having brass coupling nut and PVC washer complete all as specified and as directed 41 Supply and fix in repair Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1 m long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect asspecified and as directed. 42 Supply and fix in repair bib taps, fancy type with chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferule of 15mm bore complete all as specified and as directed. 43 Supply and fix bib taps, fancy typechromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferule of 15mm bore complete all as specified and as directed. 44 Supply and fixin repairs 15 mm bore fancy type, chromium platedStop valves / Angle cock screwed down high pressure with crutchhandle screwed both ends for iron pipe or for unions all as specified and directed. 45 Supply and fix 15 mm bore fancy type, chromium platedStop valves / Angle cock screwed down high pressure with crutchhandle screwed both ends for iron pipe or for unions all as specified and directed. 46 Supply and fixin repairs 15 mm bore fancy type, chromium plated with long shank and cup (concealed type) Stop valves / Angle cock screwed down high pressure with crutchhandle screwed both ends for iron pipe or for unions all as specified and directed. 47 Supply and fix in repair 125mm dia brass chromium plated shower rose including arm with or without swivel joints including fixing to steel pipe or union complete all as specified and directed by Engr-In Charge. 48 Supply and fix in repair Brass Chromium plated fancy type towel rail, 20mm dia, D type 600mm long between flanges including brass CP brackets complete all as specified and directed by Engr-In Charge. 49 Taking up or down 15mm dia steel tubing / CPVC pipes and connections, fittings etccomplete all as specifiedand as directed. 50 Taking up or down 20mm dia steel tubing/ CPVC pipes and connections, fittings etc complete all as specifiedand as directed. 51 Supply only ISI marked integral water proofing compound 52 Cutting chases pinning in making good for Stone concrete block or slab walls to facing where required and pointing in cement mortar 1:3 to ends or edges of concealed water tubing and similar work including making good cutting n exc 10cm girth complete all as specified and as directed. 53 Supply and fix in repairs PVC (SWR) pipes single socketed 110 mm bore in any length with rubber ring joints fixed to walls complete all as specified and directed. 54 Supply and fix in repairs PVC (SWR) pipes single socketed 110 mm bore in any length with rubber ring joints laid in floor complete all as specified and as directed. 55 Supply and fix in repairs PVC (SWR) bend withaccess door110 mm bore complete all as specified and as directed. 56 Supply and fix in repairs PVC (SWR) bend110 mm bore complete all as specified and as directed. 57 Supply and fix in repairs PVC (SWR) Branch piece single(Single Y)equal or unequal with access door 110mm bore complete all as specified and directed. 58 Supply and fix in repairs PVC (SWR) 110mm bore vent cowl complete all as specified and directed. 59 Supply and fix in repair PVC (SWR) floor trap 75mm dia, plain with grating including jointing with solvent cement complete all as specified and directed by Engr-In Charge. 60 Supply and fix in repairs PVC (SWR) pipes single socketed 75 mm bore in any length with rubber ring joints fixed to walls complete all as specified and directed. 61 Supply and fix in repairs PVC (SWR) pipes single socketed 75 mm bore in any length with rubber ring joints laid in floors complete all as specified and directed. 62 Supply and fix in repairs PVC (SWR) 75mm bore bends any radius withaccess door complete all as specified and directed. 63 Supply and fix in repairs PVC (SWR) 75mm bore bends any radius complete all as specified and directed. 64 Supply and fix in repairs PVC (SWR) Branch piece single(Single Y) equal or unequal with access door 75mm bore complete all as specified and directed. 65 Supply and fix in repairs PVC (SWR) junction single (Single T) equal or unequal with access door 75mm bore complete all as specified and directed complete all as specified and directed. 66 Supply and fix in repairsmirror of selected quality glass 600 x450 mm size with bevelled edge mirror of selected quality glass ,mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screw and cup washers complete all as specified and directed 67 Supply and fix sheet glass assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed. 68 Cutting holes into or through brick walls Superficial area n. exc 150 sqcmbuilt in , cement mortar or cement lime mortar and stone walls built in lime mortar or walls of lime concrete complete all as specified and as directed. 69 Material and labour for 25 mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate)in sub floors and finishing cement concrete surface even and rough complete all as specified and as directed. 70 Removing demolished material i.e. building material concrete debrisof any type etc to a distance of 09 KM beyond and up to 10 KMout of premises of metropolitan area including loading, unloading by manually or by mechanical means of Poclain and to be transported through trolley or tipper and staking at the destination as and when directed by Engr-In-Charge. 71 SPECIAL ITEMS OF WORK (B/R) Material and labour for mild steel Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed. 72 Supply and fix welded steel wire fabric members n exc 4 kg/ Sq M cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9 mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel , fixed all as specified and as directed. 73 Material and labour for preparation of new or previously untreated steel and iron Surfaces of any description, not otherwise descri-bed, over 10cm width or girt and applying two coats of Synthetic enamel paint (ordinary tint) over a coat of red oxide primer complete all as specified and as directed. 74 HARDSTANDINGDemolition of unreinforced cement concrete in floors and pavings not exc 15cm thick below or above ground level complete all as specified and as directed. 75 Material and labour for 100 mm thick Cement concrete type D- 2, 1:4:8 (40mm graded stone aggregate) as in sub floors and finishing cement concrete surface even and rough complete all as specified and as directed. 76 Material and labour for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade With Grey Cement and pigment complete all as specified and as directed. 77 Material and labour for Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed by Engg-in-Charge. 78 E/M PortionTaking down carefully copper/aluminiumpoint wiring (light fan socket or power) complete including fittings & fixturessuch as switches, ceiling rose, pendants, regulators, sockets, ceiling roses, pendants, regulators, light fittings etc. Removing materials to store for keeping in safe custody for taking credit and making good disturbed surfaces of walls, floors, etc. complete allas specified and as directed. 79 Taking down ceiling fansfrom ceiling, dismantling blades &refixing ofthe same includingprovision of cable from ceiling rose or connector to fan complete allas specified and as directed. 80 Taking down Exhaust Fans, from walls andrefixing the same including connecting up andprovision of cable from ceiling rose or connector to fan complete allas specified and as directed. 81 Taking down Geyserfrom walls, and handing over the same at MES store,complete allas specified and as directed. 82 Material and labour for Point wiring with cable of PVC insulated FRLS copper multistranded conductor 1.5 sqmm 1100 volts grade in and includingmedium grade 20 mm dia PVC Conduit Pipe ISI marked with all accessories and fixing arrangements concealed in Stone walls / brick masonary walls /ceilings / floors etc by cutting chassis in existing stone/ brick masonary,including fixing top cover /PVC /MS Modular type junction boxes concealed in Stone walls / brick masonary walls for housing switches/sockets/ regulators etc. with and including 1.5 sqmm PVC insulated multistranded copper earth continuity conductor connecting to the common earth dolly etc complete all as specified and as directed for the following:- 83 One lightcontrolled by 1 switch 5 amps,single pole 84 One Ceiling fan point controlled by one single pole 5 Amps switch 85 One Exhaust fan point controlled by one single pole 5 Amps switch 86 One 3 pin switch socket out let point 5 Amps switch on independent board 87 One 3 pin switch socket out let point 5 Amps switch on same board 88 One bell Pointcontrolled by one push button 5 Amps switchon independent board 89 One lightcontrolled by two nos, 2 way switch 5 amps,single pole 90 Material and labour for point wiring with cable of PVC insulated FRLS copper multistranded conductor 2.50 sqmm 1100 volts grade in and includingmedium grade 20 mm dia PVC Conduit Pipe ISI marked with all accessories and fixing arrangements concealed in Stone walls / brick masonary walls /ceilings / floors etc by cutting chases in existing stone/ brick machinery,including fixing top cover /PVC /MS Modular type junction boxes concealed in Stone walls / brick masonary walls for housing switches/sockets/ regulators etc. with and including 2.50 sqmm PVC insulated multistranded copper earth continuity conductor connecting to the common earth dolly etc complete all as specified and directed NOTE : Chases/ groove cutting shall be measured and paid separately under relevant items. 91 Supply and fix Modular switch , 1 Module single pole one way10 Amps complete allas specified and as directed. 92 Supply and fix Modular switch , 1 Module single pole one way16 Amps complete allas specified and as directed. 93 Supply and fix modular socket , 2 Module6 Amps, 2/3 pin, 240 volts Ac 2/3 pin combinedcomplete allas specified and as directed. 94 Supply and fix modular socket , 2 Module6/16Amps, 2/3 pin, 240 volts Ac 2/3 pin combined complete allas specified and as directed. 95 Supply and fix modular type fan regulator upto 120 watts with 5 step speed control for fans any sweep 1200 mm/1400 mm complete allas specified and as directed. 96 Supply and Fix modular type Bell push 6 A, 1 Module complete allas specified and as directed. 97 Supply and Fix Ding Dong Bell, AC, 230 volts, Single Pole complete allas specified and as directed. 98 Supply and fix modular white cover plate with frame, 1 module complete allas specified and as directed. 99 Supply and fix modular white cover plate with frame, 2 module complete allas specified and as directed. 100 Supply and fix modular white cover plate with frame, 3 module complete allas specified and as directed. 101 Supply and fix modular white cover plate with frame, 4 module complete allas specified and as directed. 102 Supply and fix modular white cover plate with frame, 6 module complete allas specified and as directed. 103 Supply and fix modular white cover plate with frame, 8 module complete allas specified and as directed. 104 Supply and fix metal flush box 1/2 module complete allas specified and as directed. 105 Supply and fix metal flush box 3 module complete allas specified and as directed. 106 Supply and fix metal flush box 4 module complete allas specified and as directed. 107 Supply and fix metal flush box 6module complete allas specified and as directed. 108 Supply and fix metal flush box 8 module complete allas specified and as directed. 109 Supply and fix PVC ceiling rose 65 x 50 mm surface type with 3 terminals complete allas specified and as directed. 110 Supply and fix LED Light fitting, 22 Watts, 220 volts, with driver, holder including LED tube light connecting up with 3 core flexiblecopper conductor cable of suitable size from Ceiling rose complete all as specified and as directed. 111 Supply and fix LED Light fitting, 10 Watts, 220 volts, AC decorative box type with driver, holder including LED tube light connecting up with 3 core flexiblecopper conductor cable of suitable size from Ceiling rose complete all as specified and as directed. 112 Supply and fix Sheet metal enclosures with socket plug top and MCB, Single pole & neutral enclosure with a 2 pin & earth plug & socket complete with one single pole MCB 20 amps complete all as specified and as directed. 113 Material and labour for cutting into or through the stone walls / brick wallsbuilt in cement mortar or cement lime mortar and walls of cement concrete suitable sizefor housingfor sunk box using heavy duty stone drilling/cutter machine and making good the disturbed surface all as specified and directed. NOTE : Chassis/ groove cutting in stone walls/ brick wall/ block masonary walls as required for concealed wiring shall be measured and paid separately. 114 Material and labour for Cutting chassis, pinning in Stone walls/ brick walls etc.making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings etc, for concealed conduit wiring a into or through the stone walls built in cement mortar or cement lime mortar and walls of cement concrete suitable for housing 25mm dia conduit pipe using heavy duty stone drilling/cutter machine and making good the disturbed surface all as specified and as directed. 115 Material and labour for sub main wiring with Two single core FRLS PVC insulated cable with copper conductor multistranded 1100 volts grade 2.5 sqmm in and including suitable size of non-metallic rigid PVC conduit & accessories, fixing arrangements concealedin stone wall, floor or ceiling etc by cutting chases in existing stone/ brick masonaryinc 2.5 sqmm PVC insulated multistranded copper earth continuity conductor and connecting to main earth dolly complete all as specified and directed. Note : One run of earth continuity conductor, one run of PVC Conduitand two runs of copper conductor together taken as one length for measuring unit length. 116 Material and labour for sub main wiring with Two single core FRLS PVC insulated cable with copper conductor multistranded 1100 volts grade 6.00 sqmm in and including suitable size of non-metallic rigid PVC conduit & accessories, fixing arrangements concealedin stone wall, floor or ceiling etc by cutting chases in existing stone/ brick masonaryinc 6.00 sqmm PVC insulated multistranded copper earth continuity conductor and connecting to main earth dolly complete all as specified and directed. Note : One run of earth continuity conductor, one run of PVC Conduitand two runs of copper conductor together taken as one length for measuring unit length. 117 Material and labour for sub main wiring with Four single core FRLS PVC insulated cable with copper conductor multistranded 1100 volts grade 10.00 sqmm in and including suitable size of non-metallic rigid PVC conduit & accessories, fixing arrangements concealedin stone wall, floor or ceiling etc by cutting chases in existing stone/ brick masonary inc 10.00 sqmm PVC insulated multistranded copper earth continuity conductor and connecting to main earth dolly complete all as specified and directed. Note : Two runs of earth continuity conductor, one run of PVC Conduitand Four runs of copper conductor together taken as one length for measuring unit length. 118 Material and labour for Earthing complete with galvanised steel earth plate electrode 60x60cmx6mm thick, buried directly in ground, Putting of adequate qty of salt and Char coal in layer by layer by completely covering of earth plate on surrounding sixsides, ( earth pit not less than 2.25mtrs deep below ground level) with top edge of the plate not less than 1.5mtrs below normal ground level, connected to galvanised earth lead wire 4.00 mm diaas earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point, provision of PCC earth chamber, Chamber cover, GI funnel with mesh, GI Pipe etc all as including provisionall as specified or indicted including testing on completion complete all as specified and as directed. 119 Material and labour for earth Continuity Conductor or main earthing lead fixed to wall on batten or recess or chassis or buried in ground or drawn in conduit / pipe or fixed for earthing etc. of size 4.00 mm dia galvanised iron or steel wire all as specified and as directed. 120 Supply and Fix Sheet metal enclosure for VTPN DBs double door TPN 08ways Suitable for 125 Amps MCCB Fixed in DB, deep drawn with 200 Amps rated copper bus bar 415 V, IP 43 Protection, Concealed in walls, including taking down old unserviceable from exiting place complete all as specified and as directed. 121 Supply and fix Sheet metal enclosure for DBs double door TPN, 8 ways when MCBs to be used single pole and neutral, deep drawn with 200 Amps rated copper bus bar 240V, Concealed in walls including taking down old unserviceable from exiting place complete all as specified and as directed. 122 Supply and fix MCB TPN, 63 Amps, 415 V, C- series with breaking capacity of 10KA complete all as specified and directed. 123 Supply and fix MCB SPN, 40 Amps, 240V, C- series with breaking capacity of 10KA complete all as specified and directed. 124 Supply and fix MCB SP, 6-32 Amps, 240V, C- series with breaking capacity of 10KA complete all as specified and directed. 125 Supply and fix MCCB 125 A, TPN, 25 KA complete all as specified and directed. 126 Supply and fix LED security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed. 127 Supply and fix Surge protection device Type TP+N, AC Triplepole and neutral, 20kA N complete all as specified and as directed. 128 Supply and fix 1.5m length GI Pipe 40 mm dia bend L shaped for fixing of Building security lights, including properly grouting on wall with required fixing arrangements such as bolts, nuts, screws, clamps etc complete all as specified and directed. 129 Supply and Fix Geyser 25 LitresCapacity Suitable for high pressure upto 8 bar, 2 Kilowatts, 5 Star rated,Powder coated metal body, Temperature indicating dial, fire retardant cable, Efficient long life Copper heating element, Shock proof & Rust proof ABS body, including PVC Hot & Cold pipes for inlet and outlet of geyser, complete all as specified and as directed. 130 Material and labour for sub main wiring with two single core PVC insulated cable with copper conductor multistranded 1100 volts grade 2.5 sqmm in and including heavy grade PVC conduit, surface wiring on walls and itsaccessories with fixing arrangements on pole surface, wall, ceiling etc including 2.5 sqmm PVC insulated multistranded copper earth continuity conductor and connecting to main earth dolly complete all as specified and as directed. Note : One run of earth continuity conductor, one run of PVC Conduit pipeand two run of copper conductor together taken as one length for measuring unit length.

BRR:7520000 Tender For Periodical Services To Otm Accn At Chaf Bangalore; 1 Material and labour for preparation of plastered or unplastered old decorated surfaces of walls by brooming down or with steel wire brushing, scraping down smoke soot’s, moulds, moss and efflorescent salts and treating oily and greasy spots and filling holesand cracks with suitable material like white cement or plaster of paris and applying one coat of cement base paint, including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 2 Material and labour for preparation of plastered or unplastered old decorated surfaces of walls by brooming down or with steel wire brushing, scraping down smoke soot’s, moulds, moss and efflorescent salts and treating oily and greasy spots and filling holesand cracks with suitable material like white cement or plaster of paris and applying two coat of cement base paint, including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 3 Material and labour for preparation of plastered or unplastered old decorated surfaces of walls by brooming down or with steel wire brushing, scraping down smoke soot’s, moulds, moss and efflorescent salts and treating oily and greasy spots and filling holesand cracks with suitable material like white cement or plaster of paris and applying applying one coat of exterior emulsion paint (weather coat) through mechanical means including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 4 Material and labour for preparation of plastered or unplastered old decorated surfaces of walls by brooming down or with steel wire brushing, scraping down smoke soot’s, moulds, moss and efflorescent salts and treating oily and greasy spots and filling holesand cracks with suitable material like white cement or plaster of paris and applying applying two coat of exterior emulsion paint (weather coat) through mechanical means including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 5 Material and labour for complete removal of existing treatment on walls and preparation of plastered or unplastered old decorated surfaces of walls by brooming down or with steel wire brushing, scraping down smoke soot’s, moulds, moss and efflorescent salts and treating oily and greasy spots and filling holes and cracks with suitable material like white cement or plaster of paris and applying applying two coat of exterior emulsion paint (weather coat) over a coat of primer through mechanical means including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 6 Material and labour for preparation of plastered or unplastered old decorated surfaces of walls by brooming down or with steel wire brushing, scraping down smoke soot’s, moulds, moss and efflorescent salts and treating oily and greasy spots and filling holesand cracks with suitable material like white cement or plaster of paris and applying one coat distemper oil emulsion, through mechanical means white or tinted including necessary scaffolding up to 6th storey complete all as specified and as directed by Engr-in-charge. 7 Material and labour for preparation of plastered or unplastered old decorated surfaces of walls by brooming down or with steel wire brushing, scraping down smoke soot’s, moulds, moss and efflorescent salts and treating oily and greasy spots and filling holesand cracks with suitable material like white cement or plaster of paris and applying two coats of oil bound distemper through mechanical means including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 8 Material and labour for complete removal of existing treatment on walls and applying 3mm thick wall care putty (birla putty) and preparation of surface making smooth and applying primer of chalk whitening as base coat and applying two coats of oil bound distemper through mechanical means including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 9 Material and labour for preparation of plastered or unplastered old decorated surfaces of ceiling cornices etc., by brooming down or with steel wire brushing, scraping down smoke soot’s, moulds, moss and efflorescent salts and treating oily and greasy spots and filling holes and cracks with suitable material like white cement or plaster of paris and applying one coat of oil bound distemper through including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 10 Material and labour for preparation of plastered or unplastered old decorated surfaces of ceiling, cornices etc., by brooming down or with steel wire brushing, scraping down smoke soot’s, moulds, moss and efflorescent salts and treating oily and greasy spots and filling holes and cracks with suitable material like white cement or plaster of paris and applying two coats of oil bound distemper including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 11 Material and labour for preparation of plastered or unplastered old decorated surfaces of walls by brooming down or with steel wire brushing, scraping down smoke soot’s, moulds, moss and efflorescent salts and treating oily and greasy spots and filling holesand cracks with suitable material like white cement or plaster of paris and applying one coat of white wash including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 12 Material and labour for preparation of plastered or unplastered old decorated surfaces of walls by brooming down or with steel wire brushing, scraping down smoke soot’s, moulds, moss and efflorescent salts and treating oily and greasy spots and filling holesand cracks with suitable material like white cement or plaster of paris and applying two coat of white wash including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 13 Material and labour for preparation of plastered or unplastered old decorated surfaces of ceiling by brooming down or with steel wire brushing, scraping down smoke soot’s, moulds, moss and efflorescent salts and treating oily and greasy spots and filling holesand cracks with suitable material like white cement or plaster of paris and applying one coat of white wash including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 14 Material and labour for preparation of plastered or unplastered old decorated surfaces of ceiling by brooming down or with steel wire brushing, scraping down smoke soot’s, moulds, moss and efflorescent salts and treating oily and greasy spots and filling holesand cracks with suitable material like white cement or plaster of paris and applying two coat of white wash including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 15 Material and labour for preparation of plastered or unplastered old decorated surfaces of walls by brooming down or with steel wire brushing, scraping down smoke soot’s, moulds, moss and efflorescent salts and treating oily and greasy spots and filling holesand cracks with suitable material like white cement or plaster of paris and applying applying one coat of plastic emulsion paint through mechanical means including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 16 Material and labour for preparing of old painted surfaces of wood and wood based surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 17 Material and labour for preparation of old painted surfaces of steel surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 18 Material and labour for preparation of old painted concrete surface/plaster surfaces/stone surfaces/brick and applying one coat of synthetic enamel paint etc., complete all as specified and as directed by Engr-in-charge. 19 Taking down cement plaster on brick or concrete or stone walls including racking out joints, hacking for key, scrubbing down with water etc., including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 20 Material and labour for rendering 15mm thick in cement mortar 1:4on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement including necessary scaffolding up to 6th storey complete all as specified and as directed by Engr-in-charge. 21 Material and labour for rendering 15mm thick in cement mortar 1:6on fair faces of brick work or concrete surfaces, finished fair and even etc., including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 22 Material and labour for rendering 10mm thick in cement mortar 1:3on ceiling of brick or concrete surfaces, finished even and smooth without using extra cement including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 23 Material and labour for preparing new plastered suface of walls and applying two coats distemper oil emulsion through mechanical meanswhite or tinted over a coat of primer including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 24 Material and labour for preparing new plastered suface of ceilings and applying two coats distemper oil emulsion, white or tinted over a coat of primer including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 25 Material and labour for preparing new plastered surface of walls and applying two coats of exterior emulsion paint (weather coat) over a coat of primer through mechanical means including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 26 Material and labour for preparing new plastered surface of walls and applying two coats of cement base paint over a coat of primerthrough mechanical means including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. 27 Material and labour for preparing new plastered surface of walls and applying three coats of white wash including necessary scaffolding up to 6th storey complete all as specified and as directed by Engr-in-charge. 28 Material and labour for preparing new plastered surface of ceiling and applying three coats of white wash including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge.

BRR:7519261 Maintenance and Renovation of park sec 3in mc rewari-- 1 HSR Item 26.7-Grassing of play grounds with doob grass includinguprooting rank vegetation and weeds by digging area to a depth of 30 cm , removing all weeds and other growth with roots by forking repeatedly, ploughing and dragging with ‘swagha’ breaking of clods, removal of rubbish, dressing and supplying doob grass roots, and planting at 10 cm apart in both directions , watering weedingincluding supplying and spreading of farm-yard manure at the rate of0.18 cum per 100 sqm fertilizers DAP 50 g per sqm etc and maintenance till weed free turf is formedHSR Rate(Rs.) 21.00Through Rate 2 HSR Item 20.29.1-Labour our fixing G.I. or W.I. pipe sleeve pieces in holes in walls, floors, and roofs rounds pipes including all cutting and wastage 1. 15 mm internal diameter of sleeve pipeHSR Rate(Rs.) 32.00Through Rate 3 HSR Item 11.78-Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade.HSR Rate(Rs.) 31.00Through Rate 4 HSR Item 7.22.2-Brick work with common burnt clay non- modular bricks of class designation 10.5 in superstructure above plinth level up to floor IV level in all shapes and sizes in: 2. Cement mortar 1:6 (1 cement : 6 coarse sand)HSR Rate(Rs.) 4488.00Through Rate 5 HSR Item 2.B1259- B1259. H.P. or L.P. ball valve with polythene floats: 15 mm diaHSR Rate(Rs.) 188.00Rate 6 HSR Item 13.28-Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.HSR Rate(Rs.) 75.00Through Rate 7 HSR Item 11.98.1-Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali and fungal resistance, dirt resistance exterior paint of required shade(Company Depot Tinted) with silicon additives. 1. New work (Two or more coats applied @ 1.43 litre/ 10 sqm Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm HSR Rate(Rs.) 86.00Through Rate 8 HSR Item 5.45-Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.HSR Rate(Rs.) 33.00Through Rate 9 HSR Item 4.33-Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a lead of 1 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.HSR Rate(Rs.) 138.00Through Rate 10 HSR Item 3.1.2-By Mechanical Transport including loading, unloading and stacking2. EarthHSR Rate(Rs.) 83.005km 11 HSR Item 11.93.1-Finishing walls with water proofing cement paint of required shade : 1. New work (Two or more coats applied @ 3.84 kg/10 sqm)HSR Rate(Rs.) 39.00Through Rate 12 HSR Item 20.20.2.1-Labour for laying, jointing, fixing and testing G.I./P.V.C./W.I. pipelines and special tees, bends, sockets, elbow etc. inside building and testing etc. complete including cutting threading 2.1. Including cost of specials 15 mm internal diametre of pipelineHSR Rate(Rs.) 95.00Through Rate 13 HSR Item 11.60-Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.HSR Rate(Rs.) 59.00Through Rate 14 HSR Item 26.58.1-Supply and installation of garden bench 1. Chair type garden bench with L-shaped sides made of reinforced concrete (M30), thickness 100 mm, overall height 1000 mm, base width 620 mm. Back and seat shall consist of 5 Nos. reinforced concrete planks 1500 mm x 100 mm x 50 mm one plank 1500 mm x 200 mm x 50 mm. Seating height of the bench shall be 450 mm. The bench shall be fixed with nuts on concrete mount, all holes sealed after assembly and installation. All materials required to be as per BIS specifications.HSR Rate(Rs.) 4814.00Through Rate 15 HSR Item 11.5.3-12 mm cement plaster of mix : 3. 1:4 (1 cement: 4 fine sand)HSR Rate(Rs.) 113.00Through Rate 16 HSR Item 20.31.1-Fixing and jointing gun metal peet valves (heavy pattern) with hand wheels, on G.I. pipelines laid in the ground or inside buildings, including cartage from divisional stores or nearest railway station to site of works. 1. 15 mm internal diametreHSR Rate(Rs.) 26.00Through Rate 17 HSR Item 6.1.1-Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1. 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)HSR Rate(Rs.) 3975.00Through Rate

BRR:7519084 Tender For Restoration Work Of Office Building Of Executive Engineer, Construction Block-1, Pwd, Etawah - Earth by work in surface excavation not exceeding 30 cm in depth butexceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed Engineer-in- Charge: All kinds of soil As per DSR 2.1.1 2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand) As per DSR 6.1.1 3 12 mm cement plaster in single coat on fair side of single or half brick wall for interrior plastering includign arises, interior rounded angles chamfers and of rounded angles not exceeding 80 mm in girth and finished even and smooth.As per DSR 13.4.1 4 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:3:6 (1 Cement : 3 coarse sand (zone-lll) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) As per DSR 4.1.5 5 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, reinforcement - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand (zone-lll) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) As per DSR 5.1.2 6 Mild Steel or iron in plain work such as reinforced concrete or reinforcement brick work (when not included in an over all rates) wrought to required shape as necessary including benefit for proper completion fo the work and including supply of all steel and wastage and over lappign and hooks.As per SI 504 7 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) As per DSR 21.3.1 8 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.. As per DSR 13.80 9 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. As per DSR 13.83.2 10 Finishing walls with Acrylic Smooth exterior paint of required shadeOld work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surfaceAs per DSR 13.111.1 11 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 13.99.1 One or more coats on old work. As per DSR 13.99.1 12 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 500x500 mm As per DSR 11.41.1 13 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. As per DSR 11.37 14 Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. 30mm thick shutters As per DSR 9.5.1.2 15 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. As per DSR 9.20.1 16 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever requiredOne urinal basin with 5 litre white P.V.C. automatic flushing cistern. As per DSR 17.4.1 17 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. As per DSR 18.7.1 15 mm nominal dia Pipes 18 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. As per DSR 18.7.2 20 mm nominal dia Pipes 19 Providing and fixing brass bib cock of approved quality As per DSR 18.15.1 15 mm nominal bore 20 Providing and fixing brass stop cock of approved quality As per DSR 18.16.1 15 mm nominal bore 21 Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) onforming to IS : 7231, with all fittings and fixtures complete. As per DSR 17.18.110 litre capacity - White 22 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.. As per DSR 17.17.31 23 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end). As per DSR 18.17.125 mm nominal bore

BRR:7519081 Tender For Financial Year 24-25 Under Reconstruction Work Of Bhatpura To Sakatpur Sirauli Road Avshesh Bhag - Construction of embankment with approved material obtained from borow pits with all lifts and leads trancporting upto 3 Km upto sites, spreading, grading to required slope and compected to meet requirement of table 300.2 and lead andincluding all material, labour, labour cess, T&P royalty, all tasex etc. complete as per diretcion by i-in-c but excluding G.S.T. 2 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smoothwheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3as per TechnicalSpecification Clause 405. andincluding all material, labour, labour cess, T&P royalty, all tasex etc. complete as per diretcion by i-in-c but excluding G.S.T. 3 Brick edging on both sides of the road of first class (M-150) brick on edge laid with mud mortar including labour and supply of bricks finished to the required templete and in proper alignment and also including dressing and ramming the excavated earth as directed by the Engineer-in-Charge. SI No 765andincluding all material, labour, labour cess, T&P royalty, all tasex etc. complete as per diretcion by i-in-c but excluding G.S.T. 4 Providing and applying primer coat with bitumen emulsion (SS) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70kg/sqm using mechanical means as per Technical Specification Clause 502 andincluding all material, labour, labour cess, T&P royalty, all tasex, Bitumen ect. complete as per direction by i-in-c but excluding G.S.T. 5 Providing & applying tack coat with bitumen VG-10 using pressure distributor at the rate of 0.30 kg per sqm on the prepared bituminous/granular surface cleaned with Hydraulic burmer incliding as per Tecnical Specification clause 503. andincluding all material, labour, labour cess, T&P royalty, all tasex, Bitumen ect. complete as per direction by i-in-c but excluding G.S.T. 6 P/L of open graded premix carpeting of 20mm thick composed with 13.2 mm to 5.60mm grit aggregate or approved graded grit @ 0.27 cum/10Sqm. usingbitumen (VG-10) @ 146.00 Kg./100Sqm.as bearing course, including heating of bitumen to required temperature, andincluding all material, labour, labour cess, T&P royalty, all tasex, Bitumen ect. complete as per direction by i-in-c but excluding G.S.T. Tecnical Specification clause 508 7 Providing and applying seal coat type ‘C’ with 2.36 mm gauge stone grit @ 0.90 cum/100 Sqm & bitumen (VG-10) 65 kg/100 Sqm including heating of bitumen to required temperature, mixing of stone grit with suitable mixol, laying and rolling with a smooth wheeled roller andincluding all material, labour, labour cess, T&P royalty, all tasex, Bitumen ect. complete as per direction by i-in-c but excluding G.S.T. 8 Mantinance Part A @ 7.50 % 9 Maintenance of constructed Bituminous road next five year after completion the contractor shall be paid total maintenance cost 7.5% of tender Civil Cost for five year in the form of instalment as below. The payment shall be inclusive of cess but excluding GST payment shall be done as per satisfaction of engineer in charge regarding maintenance work carried out by contractor (Including cess and Excluding GST)For 1st Year 0.00% 10 Item No. 9but for 2nd year 0.75% 11 Item No. 9but for 3rd year 1.50% 12 Item No. 9 but for 4th year 2.25% 13 Item No. 9 but for 5th year 3.00%

BRR:7518586 Tender For Construction Of Road In Mouje Gram Panchayat Ajande Matoshree Pandan. Purchase Of Materials For The Said Work. Supply As Per The Demand Of Mouje Gram Panchayat Ajande Tal. Malegaon Dist. Nashik Gram Panchayat. - Gravel (20 Mm) 2 Gravel (40 Mm) 3 Gravel (80 Mm) 4 Artificial Sand 5 Stone 6 Roller 7 Vibrator 8 Mortar

BRR:7518289 Tender For Sitc Of Lightning Conductor At 28 By1 Gariahat Road Govt Housing Block A B C D E 5 Nos. - S & F Lightning conductor Air-terminals made of 15 mm dia 1500 mm long GI pipe (ISI Medium) having five prongs of 4 SWG GI (Hot Dip) wire at top with 85 mm dia 6 mm thick GI base plate at bottom incl. necessary holes etc. duly grouted on the parapet etc. in CC mortar (4:2:1) 2 Supply & fixing GI (Hot Dip) strips 20 mm x 3 mm thick for horizontal run on the Parapet/Roof/ Wall with GI Saddles 1100 mm apart incl. mending good the damages to building works 3 Supply & fixing of GI (Hot Dip) strips 20 mm x 3 mm thick for vertical run on wall with GI saddles spaced not exceeding 1000 mm apart incl. mending good damages to building work 4 Cutting cornices/ steps etc. including cutting recess in buildings etc. & supply & fixing 15 mm bore (ISI-Medium) GI pipe protection as below and mending good damages to the building works:Length upto 0.5 Mtr 5 Making soldered joints between conductors and down pipes/ other metallic objects for 14 SWG GI (Hot Dip) wire including supply of necessary 4 SWG GI (Hot Dip) wire, jointing materials and painting with 2 (two) coats of bituminous paint 6 Hiring charges for scaffolding arrangement including dismantling at the end of work and carriage, for LC installation, per storey of building per vertical run 7 Supply & Fixing of Testing Jointsby 20 mm x 3 mm thick GI (Hot Dip) strip 125 mm long grouted on wall having clearance of 6 mm from wall for making connection with thimbles at the end of 7/10 SWG GI (Hot Dip) stranded Wire and 4 SWG GI (Hot Dip) wire of vertical conductor and conductor from earth electrode complete with S & F thimbles, GI bolts, nuts, check-nuts, spring washers etc. as required 8 Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below:By ISI-Medium GI pipe 9 Excavation of soil for installation of Earth Electrode and filling & ramming.For Soft Soil 10 Supplying & fixing medium gauge GI Pipe ( ISI-Medium) Protection with necessary fittings and jointing metarials as required 32 mm dia 11 Extra for providing masoneryenclosure on the top of the earthelectrode of overall size 86.36 cm x 86.36 cm x 46 cm deep(below Ground level) complete with cemented brick work(1:6)of 25 cm width duly plastered with cement morter (inside) CIhinged inspection cover of size 36.56 cm x 35.56 cm with lockingarrangement, GI reducer including drilling of 46 nos. 12 mm diaholes on the GI pipe 12 Extra for treatment of soil by using salt & charcoal or coke for plate electrode 13 Add. G.S.T.@ 18% (on Total from item no 1 to 12) to be calculated by bidder 14 Add. LWC.@ 1%to be calculated (on total from item no 1 to 12 + GST@18%) by bidder

BRR:7518288 Tender For Sitc Of Lightning Conductor At 32 B C Road Govt Housing A B C D E F 6 Nos Block. - S & F Lightning conductor Air-terminals made of 15 mm dia 1500 mm long GI pipe (ISI Medium) having five prongs of 4 SWG GI (Hot Dip) wire at top with 85 mm dia 6 mm thick GI base plate at bottom incl. necessary holes etc. duly grouted on the parapet etc. in CC mortar (4:2:1) 2 Supply & fixing GI (Hot Dip) strips 20 mm x 3 mm thick for horizontal run on the Parapet/Roof/ Wall with GI Saddles 1100 mm apart incl. mending good the damages to building works 3 Supply & fixing of GI (Hot Dip) strips 20 mm x 3 mm thick for vertical run on wall with GI saddles spaced not exceeding 1000 mm apart incl. mending good damages to building work 4 Cutting cornices/ steps etc. including cutting recess in buildings etc. & supply & fixing 15 mm bore (ISI-Medium) GI pipe protection as below and mending good damages to the building works:Length upto 0.5 Mtr 5 Making soldered joints between conductors and down pipes/ other metallic objects for 14 SWG GI (Hot Dip) wire including supply of necessary 4 SWG GI (Hot Dip) wire, jointing materials and painting with 2 (two) coats of bituminous paint 6 Hiring charges for scaffolding arrangement including dismantling at the end of work and carriage, for LC installation, per storey of building per vertical run 7 Supply & Fixing of Testing Jointsby 20 mm x 3 mm thick GI (Hot Dip) strip 125 mm long grouted on wall having clearance of 6 mm from wall for making connection with thimbles at the end of 7/10 SWG GI (Hot Dip) stranded Wire and 4 SWG GI (Hot Dip) wire of vertical conductor and conductor from earth electrode complete with S & F thimbles, GI bolts, nuts, check-nuts, spring washers etc. as required 8 Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below:By ISI-Medium GI pipe 9 Excavation of soil for installation of Earth Electrode and filling & ramming.For Soft Soil 10 Supplying & fixing medium gauge GI Pipe ( ISI-Medium) Protection with necessary fittings and jointing metarials as required 32 mm dia 11 Extra for providing masoneryenclosure on the top of the earthelectrode of overall size 86.36 cm x 86.36 cm x 46 cm deep(below Ground level) complete with cemented brick work(1:6)of 25 cm width duly plastered with cement morter (inside) CIhinged inspection cover of size 36.56 cm x 35.56 cm with lockingarrangement, GI reducer including drilling of 46 nos. 12 mm diaholes on the GI pipe 12 Extra for treatment of soil by using salt & charcoal or coke for plate electrode 13 Add. G.S.T.@ 18% (on Total from item no 1 to 12) to be calculated by bidder 14 Add. LWC.@ 1%to be calculated (on total from item no 1 to 12 + GST@18%) by bidder

BRR:7517232 Bids Are Invited For Mortar 80 (50Kg Bag) , Whytheat A Or Equivalent Castable Refractory In 25 Kg Bag , Whytheat A (Refractory Castable) Total Quantity : 800

BRR:7517202 Bids Are invited for Log Boom Barrier - Log Boom Barrier , Site Survey For Designinput To Prepare Effective System - Details Provided In Abstract Boq , Providing Down Stream Anchoring - Providing Down-Stream Anchoring (Chemical Anchoring With Epoxy Mortar -Fisher/ Hilti) At Spillway Pier And Divider Wall As Per Preliminary Drawing. The Construction Drawing Shall Be Submitted With Provision Of Anchoring Method. , Providing Pedestal And Anchor - Details Provided In Abstract Boq , Installing Log Boom Float - Installing Log Boom Float Modular Sections Across The River As Per The Drawing. Total Quantity : 5

BRR:7515666 Annual Maintenance Civil Of Different Govt Office Buildings Under Cooch Behar Sec-Ii,Sub Divn No-I (P.W.D), Under Coochbehar Sub Division-I (Pwd),During The Year 2025-2026.- 1 Stripping off worn out plaster and raking outjoints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. 2 Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating (ii) With 1:4 cement mortar (a) 20 mm thick plaster 3 Cleaning the exposed reinforcement preferably upto full diameter by wire brush, applying two coats of polymer based rust removing compound left for 24 hours, removing the coating and then applying two (2) coats of polymer modified anti corrosive protective coating formulated to inhibit the corrosion of reinforcement as per manufacturers specification][Mode of measurement:The affected surface area of reinforcement shall be considered for payment] 4 Ordinary Cement concrete (mix 1:2:4) with graded stone chips (6mm nominal size) excluding shuttering and reinforcement,if any, in gound floor as per relevant IS codes 5 Taking out existing partition/ceiling of particle board, masonite board, ply board, soft board etc. of any thickness and refixing same in new position with necessary clamps making holes in walls, floor, roof and mending damages if any.[concrete plaster will be paid separately] 6 (A) Wood work in posts, post plates, rafters, battens, truss members, purlins etc. fitted and fixed complete (excluding the cost of bolts, paints, but including the cost of nails, screws etc.) (The quantum should be corrected upto three decimals) (i) Sal : Siliguri. 7 Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987.i) 4mm thick clear glass 8 Rendering the surface of walls and ceiling with white cement basedwall putty of approved make and brand(1.5mm thick 9 Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturers specification) including cleaning and Two Coats 10 (a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. 11 (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary: (a) On timber or plastered surface : (iii) One coat (with any shade except white) 12 Taking out Mirzapur or glazed porcelain tiles carefully by chiselling from walls or floor including stacking serviceable material as directed. 13 Resetting old glazed porcelain tiles in 20 mm thick cement mortar (1:4) including 4 Nos of key stone (10 mm) fixed with adhesive of approved quality & 2 mm thick cement slurry using cement @ 2.91 kg/Sq.m at the back of tiles and finishing joints with white cement & colouring oxide [if required] to match the colour of tiles over application slurry @ 1.75 kg/ Sq.m below cement mortar including dismantling the old mortar etc 14 Fitting and fixing old pieces of asbestos, G.C.I. or C.I. sheets or plain sheets including closing old holes with washers and sheet-bolts and nuts, etc. and including fixing the same to supporting frame with necessary hook-bolts, washers, putty etc. (ii) With all new fittings including the cost thereof. (a) In roof 15 Galvanised corrugated iron sheet work (excluding the supporting frame work) fitted and fixed with 10 mm. dia J or L hook-bolts, limpet and bitumen washers and putty complete with 150 mm. end lap and one corrugation minimum side lap.(Payment to be made on area of finished work)(GCI sheet to be supplied by contractor) (i) In Roof:- a) With 0.60 mm thick sheet 16 Fitting and fixing old pieces of asbestos, G.C.I. or C.I. sheet or plain sheet ridging or gutter including closing old holes with washers and sheet-holts and nuts etc. and including fixing the same to supporting fram (b) With all new fittings including the cost thereof. 17 Labour for taking out door and window frame including shutter for repair or replacement of different parts of the frame & refixing the same including mending good all damaes complete. (Concrete and brick work for mending damage will be paid separately) (a) Upto area 2.5 Sq.m 18 Taking out old iron higes and fitting, fixing the same with new steel screws. (e) 100mm. Long butt hinge. 19 Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark(vii) 100mm. X 58mm. X 1.90mm 20 b) Extra for additional 3.6 height or part thereof (d) 225mm long x 10mm dia bolt 21 i) Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with16mm dia rod with centre bolt and round fitting (c) 300mm long 22 Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complet (a) With continuous plate base (Hexagonal/ Round rod)(ii) 100 mm grip x 10 mm dia rod. 23 Styles and rails of wooden shutters fitted and fixed complete. (Payment to be made on area of new work only). In Ground Floor: (i) For 25mm. Thick shutter (b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak 24 Panel (made of single plank) of door and window shutters to design as directed:(ii) 19mm thick panel of 30cm to 45cm width: (b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak 25 Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). (i) Sal : Siliguri. 26 Uprooting and removing plants from the surface of walls parapet etc and making good damages. (b) Medium size plant of girth of exposed stem above 27 Making one set of scaffolding only for replacing glass panels, painting, uprooting plant and another repairing works of building and S&P works for external works only with 10 cm. dia bamboo as main posts at the rate of 1 metre centre to centre and 7.5 cm. dia bamboo ties @ 0.75 metre apart fitting and fixing with necessary coir, nails etc. as per direction of the Engineer-incharge. a) 3.90 metre heigh 28 b) Extra for additional 3.6 height or part there of 29 ADD GST @ 18.00% ON SUM OFAMOUNT Sl-01 to SL-27 30 ADD Cess @ 1.00% ON SUM OFAMOUNT Sl-01 to SL 28

BRR:7514915 Tender For Revamping of Qila Zafargarh in Distt. Jind-- 1 Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm, removing all weeds and other growth with roots by forking including disposal of all rubbish with all leads and lifts. 2 Cleareance of debris from inside the heritage building by excavion upto depth 1.5mt to 2.0 mtr carefully without damaging the buried archaeological parts of the building and collect all the intact parts at proper place for reuse at the time of restoration work. 3 Providing and laying lime concrete with graded brick bats and 50% lime mortar 1:1:1 (1 Slaked lime : 1 Surkhi : 1 Coarse sand) rammed and finished with gur and belgiri treatment excluding cost of centring and shuttering.(Thickness 100 mm) 4 Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven storey height made with 40 mm dia M.S. tube 1.5 m centre to centre horizontal and vertical tubes joining with cup and lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffoldings for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc. wherever required for inspection of work at required locations with essential safety features for the workmen etc complete as per directions and approval of Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding.NOTE:- To be used for maintenance work judicially necessary deduction for scaffolding in the existing item to be done 5 Hiring of water tanker (4500 ltrs) during excution of work. Since the water is salty at site and its not useful for lime mortar work. 6 Applying breathable, non-reactive, antifungal, and water repellant Silane/ Siloxane chemical as approved by Archaeological Survey of India/ Engineerin- charge, of approved brand and manufacture, diluted with solvent mineral Turpentine oil in the ratio of 1:12 (One part of approved chemical :12 Part of Turpentine oil), on the existing sand stone masonry/plastered wall surface with two or more coats to give uniform application of chemical on the surface, all complete as per direction of Engineer-In-charge (The rate is inclusive of all materials and labours involved except scaffolding). 7 Provision for hiring (for 6 months) of special type of lime mortar mill (pan type) electrical/mechnical for thorough grinding and mixing of lime mortar and making lime putty as per site requirement including diesel and maintenance. 8 Curing of Lime concrete/Lime plaster surfacewith water mixed with milk of lime, pulp of belgiri and jaggery water (Gur/sheera) to achive the required hardness. 9 Construction of tanks of different sizes for slaking of lime and making lime putty as per archaelogical specification: Brick Work with common burnt clay F.P.S (non modular ) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 ( 1 cement : 4 coarse sand)complete in all respect. 10 Providing, erecting, maintaining and removing temporary protective screens made out of specified fabric with all necessary fixing arrangement to ensure that it remains in position for the work duration as required by the Engineer-in-charge. Wooven PVC cloth 11 30-40mm lime plaster in two coats with 20mm base coat in lime mortar 1:1:1 (1 lime : 1 Surkhi :1 Coarse Sand) and top coat in lime mortar 1:1:1 (1 lime : 1 Surkhi :1 Fine Sand). 12 Reconsolidation of Brick Masonry: Traditional brick masonry in lakhori bricks in lime mortar (similar to existing propotion of mortar 1:1:1 , 1 lime : 1 surkhi : sand ) 13 Technical/scientific excavation to be done manually by way of carefully digging inside the heritage structure. It also includes to avoid any damage to the heritage structure or structure underneath, without causing any vibrations and jerks to the superstructure. It also includes duly constructing centring, struting and form work to avoid any untoward incident and getting out the excavated material manually head lead approx. 50 mtr away from site. 14 Consolidating the base area including cutting and filling, rammimg and watering complete to make the surface good for laying of concrete including appropriate slope required to safeguard the surface from rain water. 15 40 mm thick (Aevrage) fine dressed stone flooring over 20 mm (average) thick base of lime mortar 1:1:1 (1 lime: 1 surkhi:1coarse sand) with joints finished flush. 16 Providing and supplying as per preliminary project report for development of basic amenities in herirage sites and monumnets, stone benches, signage, dustbins, designed to complement the aesthetics of the heritage structure and the site. The furniture should be made from durable, heritage-appropriate materials as per site requirements. Stone benches/tableNote: The entire process must be executed under the strict supervision of an architect, archaeological engineer, or archaeologist to ensure compliance with heritage conservation norms and site sensitivity. 17 Providing and supplying as per preliminary project report for development of basic amenities in herirage sites and monumnets, stone benches, signage, dustbins, designed to complement the aesthetics of the heritage structure and the site. The furniture should be made from durable, heritage-appropriate materials as per site requirements. Informational Signage made with stoneNote: The entire process must be executed under the strict supervision of an architect, archaeological engineer, or archaeologist to ensure compliance with heritage conservation norms and site sensitivity. 18 Providing and supplying as per preliminary project report for development of basic amenities in herirage sites and monumnets, stone benches, signage, dustbins, designed to complement the aesthetics of the heritage structure and the site. The furniture should be made from durable, heritage-appropriate materials as per site requirements. Dustbins matching with site/built fabricNote: The entire process must be executed under the strict supervision of an architect, archaeological engineer, or archaeologist to ensure compliance with heritage conservation norms and site sensitivity. 19 Brick on edge flooring with bricks of class designation 7.5 on a bed of 12mm lime mortar, including filling the joints with same mortar, with common burnt clay non modular bricks: 1:1:1 (1 lime : 1 surkhi : 1 coarse sand) 20 Recessed Pointing with 1:1:1 ratio composite lime mortar (1 lime : 1 coarse sand : 1 surkhi) mixed wth colour pigment including racking out joints etc. and supply of all materialslabour TandP etc. required for proper completion of work. 21 Provisions for basic amenties at a suitable site that does not harm or obstruct the view of the heritage structure, as per preliminary project report for development of basic amenities in herirage sites and monumnets. It incldues an attendant room, washroom facilites, water point, ticket counter/ tourist information centre.Note: The work must be carried out very carefully to ensure that it does not harm the heritage site. The aesthetics should align with heritage norms and the site’s character, and all materials must be heritage-compatible and design as per the site requirement. The entire process must be executed under the strict supervision of architect/archaeological engineer/archaeologist.

BRR:7514755 Tender For Reconstruction Work On Nagla Mafi Chaukpuri Road - Providing, Laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per Technical Specification Clause 405including all material, labour, cess, T&P, machinery, and all taxes etc. complete direction by E-I/c but excluding G.S.T. 2 Providing, Laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405including all material, labour, cess, T&P, machinery, and all taxes etc. complete direction by E-I/c but excluding G.S.T. 3 Brick edging on both side of road of first class (M-150) brick on edge laid with mud mortar including labour and supply of bricks finished to the required templete and in proper alignment and also including dressing and ramming the excavated earth as directed by Engineer-in-charge (S.I. No.-765) including all material, labour, cess, T&P, machinery, and all taxes etc. complete direction by E-I/c but excluding G.S.T. 4 Providing and applying primer coat with bitumen emulsion (SS) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means as per Technical Specification Clause 502 including all material, labour, cess, T&P, machinery, and all taxes etc. complete direction by E-I/c but excluding G.S.T. 5 Providing and applying tack coat with Bitumen VG-10 using bitumen distributor at the rate of 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503but excluding GSTincluding all material, labour, cess, T&P, machinery, and all taxes etc. complete direction by E-I/c but excluding G.S.T. 6 Providing laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finish to required level and grades to be followed by seal coat of Type C as per Technical Specification Clause 508including all material, labour, cess, T&P, machinery, and all taxes etc. complete direction by E-I/c but excluding G.S.T. 7 Providing and laying seal coat by manual means with VG-10 Grade Bitumen sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type C as per Technical Specification Clause 510 including all material, labour, cess, T&P, machinery, and all taxes etc. complete direction by E-I/c but excluding G.S.T. 8 Earth work in cutting or in embankment in ordinary soil, excavation to be in the form of regular pits not exceeding 1/2 meter(20) depth and earth work in embankment to be in 20 cm. (8)layers including ramming and dressing the surface to required levels and slopes and also including 1.50 M(5ft.) lifts and 30M (100ft.) lead. The earth from cutting to be used in making embankment or to be deposited as spoil banks with in 30M(100ft.) distance as directed by the Engineer-in-charge but excluding GST (SI. No. 253A Ch-4)including all material, labour, cess, T&P, machinery, and all taxes etc. complete direction by E-I/c but excluding G.S.T. 9 Maintenance of road for next five year after completion contractor shall be paid total maintenance cost 7.50% of Civil Cost for five year in the form of instalment as below. The payment shall be inclusive of cess but excluding GST payment shall be done as per satisfaction of engineer in charge regarding maintenance work carried out by contractor (Including All Taxes but Excluding cost of GST.)For 1st Year 0.00% 10 Item No. 11but for 2nd year 0.75% 11 Item No. 11but for 3rd year 1.50% 12 Item No. 11 but for 4th year 2.25% 13 Item No. 11 but for 5th year 3.00%

BRR:7514745 Tender For Hinchhpur Pal Basti To Sundarpur Harijan Basti Road - Construction of Embankment withapproved material obtain from Borrow pits with all lift and lead, transporting to site ,spreding grading to required slope and compacting to meet requirement of Table-300-2 2 Construction of granular sub base by providing well graded material spreading in uniform layer with motor grader on prepared surface mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel rollar to achieve the desired density,complete as per Technical Specification clause 401. 3 Providing, laying, spreading and compacting stone aggregates of specific sizes (45-63 mm) to water bound macadam specification including spreading in uniform thickness,hand packing,rolling with smooth wheel roller 80-100 KN in stages to proper grade and camber, applying and brooming requisite type of screening / binding materials to fill up the interstices of coarse aggregate,watering and compacting to the required density . WBM Grading-II as per Technical Spcification clause 405. 4 Providing,laying,spreading and compacting stone aggregates of specific sizes (22.4-53 mm)to water bound macadam specification including spreading in uniform thickness,hand packing,rolling with smooth wheeI roller 80-100 KN in stages to proper grade and camber, applying and brooming requisite type of screening / binding materials to fill up the interstices of coarse aggregate,watering and compacting to the required density. WBM Grading-III as per Technical Spcification clause 405. 5 Brick Edging on both sides of roads of straight over burnt brick Class-150 Bricks/ 7.50 cm wide and 11.5cm. deep laid with mud mortarfinished to required templatein proper alignment & including dressing & ramming the excavated earth as directed by E/I as per S.I. No. 765. 6 Providing and applying primer coat with bitumen emulsion (SS) on prepared surface of granular base including cleaning of road surface and spraying primer @ 0.70 kg/sqm using mechanical means as per Technical Specification Clause 502. 7 Providing and applying tack coat with bitumen (VG-10) using bitumen Emulsion pressure distributor @ 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with mechanicalbroom as per Technical Specification Clause 503. 8 Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen @1.46 kg/sqm to required line,grade and level to serve as wearing course on a previously prepared base including mixing in a suitable plant, laying and rolling with three wheel 80-100 kN static rollar capacity finished to required level and grades to be followed by seal coat of Type-C as per TechnicalSpecificationClause 508. 9 Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels grade and cross fall using Type-C with bitumen binder @ 0.65 kg/sqm including cost of bitumen as per Technical Specification Clause 510. 10 Construction of Subgrade and Earthen Shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000m as per Technical Specification Clause As per MORD 303.1 11 Construction of Embankment withapproved material obtain from Borrow pits with all lift and lead, transporting to site ,spreding grading to required slope and compacting to meet requirement of Table-300-2 12 Cement Concrete with 4 cm, gauge approved stone ballast, approved coarse sand and cement in the proportion of 6:3:1 in fondation including supply of all material, labour, T&P etc. required for proper completion of the workAs per S.I. No. 280. 13 Providing and laying 350 mm dia NP-3 Hume pipe jointing with coller in proper position with cement mortar 1:2 including cost of cement, jute etc. required for proper completion of the work. 14 Providing and laying 600 mm dia NP-3 Hume pipe jointing with coller in proper position with cement mortar 1:2 including cost of cement, jute etc. required for proper completion of the work. 15 1st class brick work in 4:1 fine sand and cement of 1.25 fineness modulus mortor in foundation & plinth including supply of all material, labour and tools and plants etc. required for proper completion of the workAs per S.I. No. 305. 16 Struck cement pointing with cement mortor consisting of 1:2 one part cement and two part of sand of 1.25 F.M. including supply of all material, labour, tools and plants etc. required for proper completion of the work As per S.I. No. 574. 17 Maintance Cost of Ist Year@ 0.00% 18 Maintance Cost of 2nd Year@ 0.75% 19 Maintance Cost of 3rd Year @ 1.50% 20 Maintance Cost of 4th Year@ 2.25% 21 Maintance Cost of 5th Year@ 3.00%

BRR:7511364 Tender For Divider, Tile, Railing Repair And Painting Work On Other District Roads In Ghaziabad District - Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401. including supply of all materials, labour, tools & plants etc. required for proper completion of the work as per direction of Engineer-in-charge and inlcuding all texes but excluding GST. 2 Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam (WMM) specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with grader in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density. including supply of all materials, labour, tools & plants etc. required for proper completion of the work as per direction of Engineer-in-charge and inlcuding all texes but excluding GST. 3 Providing and Laying of Interlocking Concrete Block Pavements having thickness80mmasperdrawingsand Technical Specification Clause 1504. (ISI MARK INTERLOKING TILES) including supply of all materials, labour, tools & plants etc. required for proper completion of the work as per direction of Engineer-in-charge and inlcuding all texes but excluding GST. 4 Cement Concrete with 4 cm gauge approved stone ballast, coarse sand & cement in the proportion of 8:4:1 including supply of all materials, labour, Tools & plants etc. required for proper completion of the work.including supply of all materials, labour, tools & plants etc. required for proper completion of the work as per direction of Engineer-in-charge and inlcuding all texes but excluding GST.(as per SOR-289) 5 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). including supply of all materials, labour, tools & plants etc. required for proper completion of the work as per direction of Engineer-in-charge and inlcuding all texes but excluding GST.(As per DSR-2021 Sl. No.-16.69) 6 First class Brick Work in 1:4 one cement & four Coarse sand of 2.20 F.M. mortar in foundation and plinth including supply of all materials, labour and T&P etc. requried for proper completion of the work as per direction of Engineer-in-charge and inlcuding all texes but excluding GST.(as per SOR -305a) 7 Cement Concrete with 2 cm gauge approved stone ballast, coarse sand & cement in the proportion of 4:2:1 including supply of all materials, labour, Tools & plants etc. required for proper completion of the work as per direction of Engineer-in-charge and inlcuding all texes but excluding GST. (As per SOR-279a) 8 12 mm thick plaster with cement and coarse sand of 1.25 fineness modules in 1:4 over brick work minimum thickness not to be less than 1cm. including supply of all materials, labour, tools & plants etc. required for proper completion of the work as per direction of Engineer-in-charge and inlcuding all texes but excluding GST. (as per SOR -384 new item) 9 Providing wall putty on new surface with approved quality material of Berger/ J.K./Birla or similar make 2 coats. including supply of all materials, labour, tools & plants etc. required for proper completion of the work as per direction of Engineer-in-charge and inlcuding all texes but excluding GST.(As per SOR-15.22 New Item) 10 Painting or varnishing with valsper or other approved high grade enamel or superior synthetic clean varnish complete one coat over (every subsequent coat on previously treated) previously painted surface including supply of all materials, labour, Tools & plants etc. required for proper completion of the work as per direction of Engineer-in-charge and inlcuding all texes but excluding GST. Paint to be used should confirm ISI no. 105/106/133-1950. (S.I. no. 647+648)

BRR:7511321 Tender For Work of CC road and drain from Madrasa to Masha Allahs house in Ward No. 74 Sant Jhulelal Nagar - Cleaning of site etc. 2 Earth work in excavation in foul positionsoil lead 50mt.& lift 1.5 mt. incl. lab. T&P etc all complete . 3 P/L of base concrete in 1:6:12 with cement, L-Sand and 40mm S/B including mat. Lab. T&P,etc all complete. 4 M 150 class brick work in 1:4 with cement &approved Course Sand mortar including supply all material and S.I.N. labor etc. 5 12mm thick cement plaster in 1:4 cement mortorwith 1cement and 4 course sand including etc. all complete of work. 6 Laying C.C in 1:2:4for top of drainwork.with cement, Course Sand20 mm & Stone Grit including supply of all material and labour etc. 7 P/L of 125 micron polythineincluding etc. all complete of work. 8 S/LayingofGSB53.-9.5 mm thick S/Bupto 10Cm loose Layer including etc. all complete of work. 9 Consolidation ofGSBupto 10 cm thickloose layer by Road Rollerincluding etc. all.complete. 10 Water allowance to be allowed on above incl.Lab. T&P,etc all complete. 11 P/fixing ofRoad Barricating including etc. all complete of work. 12 P/LC.C in 1:1.5:3for roadwork.with cement, Course Sand20 mm & Stone Grit including supply of all material and labour etc. 13 cc cutting 14 RCC Work with cement concrete (1:1.5:3) including all completion of work. 15 M.S or iron workin renforcement cutting bending , binding ,and placeing incl. etc. all. 16 P/L 80 mm thick rubber mould interlocking paverwith local sard filling etc.

BRR:7511294 Tender For Civil maintenance work in residence no. 4 and 6 situated at Lal Bahadur Shastri Marg - Providing and layeing in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level:1:5:10 (1 cement :5 coasre sand ( Zone-III) :10 graded stone aggregate 40 mm nominal size dar-4.1.10 2 Providing and fixing C.P.Brass Angle Valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15 mm nominal bore ( 18.53.1) 3 Providing and fixing C.P.Brass extentsion nipple (Size-15x50mm) of approved make and quality as per direction of engineer-in-charge. ( 18.53A) 4 Providing and fixing ISI marked IS:1341 M.S. pressed butt hinges bright finished with necessary screws etc.100x58x1.9mm complete (DAR9.55.2) 5 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378). 250x16 mm (DSR -9.62.2) 6 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378). 250x10 mm(DSR -9.63.1) 7 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378). 200x10 mm(DSR -9.63.2) 8 Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete (Copper oxidised as per IS 1378). 125 mm (DAR -9.66.1) 9 Providing and fixing G.I. Union in G.I. pipe incluliding cutting cutting and threading the pipe and making long screw etc, complete, New work, ( 25 mm nominal bore ) 18.46.3 10 Providing and fixing ISI markedflush door Shutters Conforming to IS : 2202 (Part I) Non decorative type core of block board construction with frame lst class hard wood and well matched commercial 3 ply Veneening with vertical graints or cross brand and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt Hinges with Necessary Screws.DAR N0-9.21.1, 11 Providing And FixingFly Proof galvanized M.S. wire gauge to windows and Clerestory window using wire gauge with average widht of aperture 1.4 mm both directions with wire of dia 0.63 mm all complete with second class teak wood beading 62x19 mm. DAR No-9.51.1, 12 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door widht upto 700 mm), with necessary accessories and screws etc. complete. DAR-9.83, 13 Providing and fixing ISI marked oxidised M.S Tower bolt black finish (Barreltype) with necessary screws etc complete Copper Oxidised as per lS 1378, 250x10 mm(DAR -9.63.1) 14 Providing and fixing bright finished brass lower bolts (barrel type) with necessary screws etc complete. 250x10 mm (DAR -9.74.1) 15 Providing and fixing bright finished brass lower bolts (barrel type) with necessary screws etc complete. 200x10 mm (DAR -9.74.2) 16 Providing and fixing wash basin with C.l. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. Stainless Steel A lSl-304(18/8) Wash basin Size-530x345 mm with single 15 mm C.P. brass pillar tap. (17.7.11) 17 Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete. Flexible pipe 32mm dia(17.28.2.1). 18 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass Screws and washers complete. (17.31). 19 Providing and fixing 600x120x5 mm glass Self with edge round off, supported on anodiesd aluminium angle frame with c.p. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc. complete.(17.33). 20 Providing and fixing Chlorinated Polyyinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threated fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joints of pipes & fitting with one step CPVC solventcement and testing of joints complete as per direction of Engineer -In-charge. Internal work -Exposed on wall (20 mm nominal dia pipe )18.7.2, 21 Providing and fixing G.I. Pipe complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. inernal work - exposed on wall. ( 25 mm nominal bore ) 18.10.3, 22 Cleaning and desilting of gully trap chamber, including removal of rubbish mixedwithearthetc.anddisposalofsame,allasperthedirectionof Engineer-in-charge.(DAR14.76) 23 Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge (DSR 1.1.18) 24 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes DSR-10.16.1 25 Providing and fixing C.P.Brass bib cock of approved quality conforming to IS: 8931 15 mm nominal bore ( 18.49.1) 26 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.(dar-11.38) ( size of tile 300x300mm ) 27 Laying old cement cocrete interlocking paver blocks of any design/ shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. (Old CC paver blocks shall be supplied by the department free of cost).DSR NO-13.84 28 Dismantling Old Plaster or SkirtingRacking out joint and cleaning the surface for plasterincluding disposal of rubbish to the dumping ground within 50 metars lead. DAR No-15.56, 29 15 mm cement plaster on rough side of single or half brick wall of mix:. DAR-13.5.1, 30 Removing White or Colour wash by Scrapping and sand papering and preparing the surface smoothincluding necessary repairs to scratches etc. complete.DSR-13.88, 31 Providing and Applying white Cement based Putty of average thickness 1 mm. of approved brand and manufacture. Over the Plastered wall Surface to Prepare the Surface even and Smooth Complete. (DSR-13.80), 32 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade.;Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface DSR 13.111.1

BRR:7510781 Tender For Provision Of 02 X Training Shed At Fatehgarh; 1 M & L for surface dressing n.exc. 15 cm deep and getting out in soft/loose soil complete all as specified and directed. 2 Excavation over areas, n exc 1.5 m deep for foundation and getting out in soft/loose soil complete all as specified and directed. 3 Excavation over areas,exc 1.50 m but not exc.3 m depth for footing in soft/loose soil etc cpmplete all as specified and directed. 4 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm of soft/ loose soil complete all as specified and directed. 5 Removing excavated material (soil) n. exc. 50 m and depositing where directed at alevel n. exc. 1.5m above the starting point etc complete all as specified and directed. 6 M & L for PCC 1:3:6type C-2 (using 40 mm graded stone aggregate) as infoundations, filling and mass-concrete etc complete all as specified and directed. 7 M & L for RCC M-25 design mix (using 20 mm graded stone aggregate ) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete etc complete all as specified and directed. 8 M & L for RCC M-25 design mix (using 20 mm graded stone aggregate)as in Columns, pillars, piers, posts and struts etc completeall as specified and directed. 9 M&Lfor RCC M-25 design mix (using 20 mm graded stone aggregate)as in Beams, cantilevers, bressummers, lintels over 1.5m span etc completeall as specified and directed. 10 M & Lfor RCC M-25 design mix (using 20 mm graded stone aggregate)as in Chajjas, Gutteretc completeall as specified and directed. 11 `M & LforRCC M-25 design mix (using 20 mm graded stone aggregate )as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc completeall as specified and directed. 12 M & Lfor RCC M-25 design mix (using 20 mm graded stone aggregate )as in stair ways including steps (square or spandril), string pieces, carriages, etc., complete, any section straightetc completeall as specified and directed. 13 M & L for flat, rough finished surface formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batteretc complete all as specified and directed. 14 M & L for for flat, rough finished surface form work as in sides of columns etc complete all as specified and directed. 15 M & L for for flat, rough finished surface form work as in roof beams ,lintel and intermediate beametc complete all as specified and directed. 16 M & L for flat, rough finished surface formwork to soffits of suspended slabs such as roof slabs, floorslabs, landings and similar work; not exceeding 200mm thick(Horizontal or sloping etc complete all as specified and directed. 17 M & L forflat, rough finished surface formwork to chullah hoods, chajjas, Gutter and similar items including edgesetc complete all as specified and directed. 18 M & L for rough finished surface formwork to staircases with sloping or stepped soffits including risers and stringers (excluding landing) etc complete all as specified and directed. 19 S & F for roof trusses (framed),crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc conforming to Fe 410-W (Gde E-250) quality B complete all as specified and directed. 20 S & F for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc conforming to Fe 410-W (Gde E-250) quality B complete all as specified and directed. 21 S & F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed. 22 S & F for pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in ridge/valley gutter roof covering/ cladding to wall, fixed with self tapping screws as specified and directed. 23 S&F MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment (Fe 410-W (Gde E- 250) quality A ) complete all as specified and directed 24 S&F Mild steel screw bolts of 16-20 mm dia and length of bolt exc 5cm but n exc 10cm long (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square complete all specified and directed 25 M & L for preparation of new or previously untreated surfaces of steel over a coat of red oxide primer over and encluding two coat of synthetic enamel paint, surface of any description over 10cm in width or girth, not otherwise described complete all as specified and directed. 26 M & L for rendering 15 mm thick in CM 1:4 on bricksurfaces fair finished even and smooth without using extra cement complete all as specified and directed. 27 M & L for rendering 5 mm thick in CM 1:4 on concrete surfaces fair finished even and smooth withoutusing extra cement complete all as specified and directed. 28 M & L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over one coat of putty complete all as specified and as directed. 29 M & L for moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering etc all as specified and directed. 30 M & L for PCC 75mm thick1:3:6 type C-1using 20 mm stone aggretate as in plinth protection including joint fillingand coarse sand mixture. 1:3 (by weight) at the joints complete all as specified and directed. 31 M & L hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface(Broken stones / boulders) etc complete all as specified and directed. 32 M & L for 75 mm thickPCC, 1:4:8 type D-2,(40mm graded stone aggregate) as in base /sub base of floor complete all as specified and directed. 33 M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified and directed. 34 M & L for mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders etc complete all as specified and directed. 35 M & L for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 etc all as specified and directed. 36 M&L for machine cut kota stone with mirror polishingforflooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete.Including Screed bed or bedding layer of mortar 20 mm thick in CM 1:6 for laying floor finishes complete all as specified and directed. 37 M&Lfor green marble 18 to 20mm thick(table rubbedand polished)in steps,jambs,pillars, window cills, cooking platforms and border of kota stoneincludingpointing in white cement (1:2) usingmarble dust with admixture of pigment to match with marbleshadeincluding 15mm screed bed in cement mortar (1:4)complete all as specified and directed. 38 M&Lformarble matching with platformcolour 18 to 20mm thick(table rubbedand polished)in riser and vetrical face of brick /RCC wall includingpointing in white cement (1:2) usingmarble dust with admixture of pigment to match with marbleshadeincluding Rendering 10 mm thick in cement mortar (1:4)on fair faces of brick work or concrete surfaces complete all as specified and directed. 39 M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, includingfixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel boltsetc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed 40 S&F 15 mm bore tubes medium grade galvanised, with all fitting and fixed complete to wall and ceilings or laid in floor complete all as specified and directed. 41 S&F 20 mm bore tubes medium grade galvanised, with all fitting and fixed complete to wall and ceilings or laid in floor complete all as specified and directed. 42 S&F rotational moulded polyethylene water storage tanks 1000 ltr capacity in triple layer (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PTMT Float valve complete all as specified and directed. 43 S&F gun metal glove or gate valve with iron wheel head, screwed both ends for 20 mm iron pipe and fixed screws complete all as specified and directed. 44 S&F15 mm dia bore stop angle cock chromium plated screwed down high pressure with crutch or butterfly handle,screwed both ends for iron pipe or for unions complete all as specified and directed. 45 S & F PVC ( SWR )pipe 75 mm dia single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed. 46 S&F 110 mmbore PVC(SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. 47 S&F 110 mm bore PVC(SWR) bends any radius complete all as specified and directed. 48 S&F 75 mm bore PVC(SWR) bends any radius complete all as specified and directed . 49 M&L 75 mm dia. PVC floor trap with grating including joining to waste pipe fixed in solvent cement complete all as specified and directed. 50 S&Fvitreous chinawash hand basins, white , flat back of size 550 x 400 mm including 32mm bore waste coupling chromium plated including 32mm bore pvc waste pipe including fixing cantilever brackets connection unions to pipes etc fixed complete all as specified and directed . 51 S&F 15 mm bore bib taps fancy type cast copper alloy chromium plated long shank with crutch or butterfly handle screwed down for iron pipe or brass ferrule and fixed complete all as specified and directed. 52 S&FPVC connnection 15mm size with PTMT nuts of length 450mm long complete all as specified and directed. 53 S&F 15mm bore pillar tap fancy type cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed. 54 S&Fvitreous china urinal, half stall type (white) with grating and union for discharge pipe, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) etc complete all as specified and directed. 55 S&F vitreous china urinal partition white of size 310 mm X 700 mm complete all as specified and directed. 56 M&L PCC 1:3:6 type C-2 (using 40 mm graded stone aggretate) concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 10 mm bore pipe complete all as specified and directed. 57 M&L for salt glazed stone ware drain pipes grade A of size 100 mm laid in trenches and jointed in CM (1:1) complete all as specified and directed. 58 M&L for non- kid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed layer of mortar 15mm thick in CM 1:6 for laying floor finishes complete all as specified and directed. 59 M&L for Glazed ceramic coloured tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including rendering 10mm thick CM 1:3 on fair faces of brick work or concrete surfaces complete all as specified and directed. 60 S&F solid PVC door frame of size 50mmx 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, as per SSR specification all as pecified and directed. 61 S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tube for top and bottom rails, MS frame shall be covered with sheet molded plain colour PVC sheet fixed with 20mm width sturck in side with solvent cement for style and plain colour PVC sheet for top rail, lock rail and bottom rail on either side as in gap insert for top rail, botttom rail paneling or plain colour PVC sheet beading and jointed together with solvlent cement, fixing in the frame at site as per SSR specificationcomplete all as specified and directed. 62 S&F 150 mm aluminium anodized, barrlel tower bolts of extruded section complete all as specifed and directed. 63 S&F 200 mm long aluminium anodized, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed. 64 S&F 100 mm long butt hinges, cast brass,with mild steel hinge pin, bright polished and fixed, type B-11 with steel screws as in pvc door complete all as specifed and directed. 65 S&F Steel windows or ventilators, fixed type, with glazing barscomplete all as specified and directed. 66 S&F for sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm complete all as specified and directed. 67 S & F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors, ladders, framed balusters, walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165complete all as specified and directed. 68 S & F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples in steel window/ventilator complete all as specified and directed. 69 S&F 100mm aluminium handles, fabricatd type, anodised complete all asspecified and directed. 70 Surface excavation n.exc 35cm deep and averaging cm and averaging 15cm deep and getting outin soft/loose soil complete all as specified and directed 71 Rolling and consolidating formation surfaces in cutting with power roller exc 8 ton but n exc 12 ton complete all as specified and direcetd 72 M&L for soling (or sub base) 150mm thick (spread thickness) with granite, trap or basalt broken boulders or quarried stones, interstices filled, surface and rolled and consolidated to required gradient and camber 73 M&L for WBM 150mm thick (compacted thickness) in two layers of 75mm each with course aggregate of grading II (63 to 40mm) size, spread, leveled and rolled and consolidated to required gradient and camber using grainite, trap or, basalt stone complete all as specified and directed 74 M&L for preparing unsurfaced WBM surface by wire brushing with wire brushed for removing caked mud etc sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dust etc complete all as specified and directed. 75 M&L for applying evenly a priming tack coat with bituminous primer @ 10Kg/10Sqm using paving bitumen complete all as specified and directed. 76 M&L for 75 mm thick (consolidated thickness) premix bituminious macadam with 4% binder contentusing paving bitumen of VG-30 grade by weight of total mix laid / rolled and compacted to required camber and gradient complete all as specifiied and directed.Note : (a) Premix bituminious macadam shall be obtained from hot mix plant and spreading shall be done with mechanical paver and asphaltic dense concrete work shall be done within 48 hours after completion of rolling and consolidation of bituminious macadam. (b) Contractor shall quote his rate on the basis of binder as mentioned in above item.If there is any variation in the actual binder content used,the rate shall be adjusted @ Rs. 45/- per Kg of the binder used.However no price adjustment shall be made if the binder content workout to more as specified in shedule A. 77 M&L bituminous premix asphaltic dense concrete 40mm consolidated thickness with 5.5% binder using paving bitumen content by weight of total mix, rolled and compacted to required camber and gradient complete content by weight of total mix rolled and compacted using 8 to 10 tonne capacity power road roller to achieve the required compaction camber and gradient complete all as specified and directed. 78 M&L continuous brick edging; with width equal to the depth of the brick, of whole sub-class B Bricks old sizelaid on end vertically complete all as specified and directed. 79 Removing excavated material (hard/dense soil) to a distance exceeding 50m and not exceeding 100m& depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed. 80 Supply and fixing cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per manufactures instructions complete all as specified and directed. 81 M & L for preparing bituminous surfaces of road and marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like n. exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed. 82 Surface excavation n. exc 30 cm deep and averaging 15 cm thick in soft/loose soil etc complete all as specified and directed. 83 M&L for 75mm thick PCC 1:4:8 type D-2(using 40 mm graded stone aggregate) as in lean concrete etc complete all as specified and directed. 84 Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of requiredshape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete.etc complete all as specified and directed. 85 M&Lfor PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in kerb, benching etc complete all as specified and directed. 86 Excavation in trenches not exceeding 1.5 mtrs wide and not exceeding 1.5 mtrs in depth for foundation, etc or for shafts, wells, cesspits, manholes, laying of cables including getting out in soft/loose soil complete all as specified and directed. 87 Cutting existing CI/GI pipe line 40 mm dia for insertion of tee of size 40 x 40 x 40 mm for branch connection including excavation and earth work complete all as specified and directed. 88 Cutting existing CI/GI pipe line 40 mm dia for insertion of tee of size 40 x 40 x 25 mm for branch connection including excavation and earth work complete all as specified and directed. 89 Supply and fixing for 40 mm bore galvanised steel tubing, medium grade with all fittings and fixed to wall, ceilings or laid in floor, trenches complete all as specified and directed. 90 Supply and fixing for 25 mm bore galvanised steel tubing, medium grade with all fittings and fixed to wall, ceilings or laid in floor, trenches complete all as specified and directed. 91 Supply and fix gun-metal, globe or gate valvs, 25 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. 92 S&F Mild TMT steel bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bendingand binding with the mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed 93 M&L pre-cast RCC 1:2:4 Type B-1 (20mm graded stone aggregate) as in cover slab for drain and similar work complete all as specified and directed 94 M & L PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate)as in bed of surface channel of drain including providing necessary formwork complete all as specified and directed. 95 M&L extra for forming fair finished drain or channel 30 cm inner girth in cement concrete,using extra cement including forms,moulds, mitred/stopped ends etc. complete all as specified and directed 96 Removing excavated material exc. 100 m but n exc. 200 m and depositing where directed complete all as specified and directed. 97 M&L for soakage wells of size (3.0 M dia x 4.5 M effective depth) including excavation, in any type of soil, foundation in PCC 1:3:6 type C-1 (using 20 mm graded stone aggretate), walls of honey combed masonary in CM 1:4 with cover slab of M-25 precast concrete/SFRC cover, top ring RCC 1:2:4 type B-1 (using 20 mm graded stone aggretate), including intercepting chamber and screen chamber made ofbrick masonary in CM,interconnecting pipes of RCC/DWC complete filled with brick bats complete all as specified and directed. 98 Excavating post holes in soft/Loose soils (or similar holes ) nexc 0.50 Cum each and getting outand returning filling in balance portion (after PCC filling Ref note given below) with boulder and mixed with earthin layers exceeding 25 Cm thick complete all as specified and directed. 99 S&F posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc flat iron fillets (for securing wire mesh etc) including all necessary drilling bolting or riveting etc; half round or other stock section, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. 100 Supply and fixing mild steel in flat,round or square bars in available legth complete all as specified and directed. 101 M & L for PCC 1:4:8 type D-2 (40mm gradedstone aggregates) in foundation filling and mass concrete complete all as specified and directed 102 M&L for RCC 1:2:4 type B-1, (20mm graded stone aggregate), nominal mix in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. 103 M & L for preparation of new or previous untreated steel and ironsurfaces of anyn. exc 10 cm in width or girth and applyingtwo coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed . 104 S&F for GIbarbed wire 2 strand steel barbed wire 2.24 mm dia barbed with 2 mm barbs at 75 mm spacingand shallconfirming to IS-278-2001 &IS-280-2006 and straining and fixing to any type of standrad rails straining bolts including securing or tying at crosssing with and provision of Galvanized mild steel wire, staples or steel pins etc as directed complete all as specified and directed. 105 Supply only chain link MS galvanised fencing weight not more than 4 Sqm any size or type complete all as specified and directed. 106 Fixing only chain link fencing including line wires ,any mesh and any type of standrads rails, straining bolts etc including provisioning of binding wire complete as directed. 107 Mild steel screw bolts (Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 5 Cm long but not exceeding11 to 15mm dia of neck complete all as specified and directed. 108 M&L for 5.5m steel gate complete all as shown on drg No. TD/104/11 complete all as specified and directed. 109 M&L for point wiring complete forOne light/Fan/Exhaust fan/Bell pointcontrolled by one switch with PVC insulated and unsheathed FRLSH cable 1.5 sqmm (nominal area), ISI marked,multi stranded copperconductor cable, 1100 volt grade including ISI marked not less than 20mm dia medium grade PVC conduit concealed in wall , MS conduit in roof/floors, factory made pressed steelconcealed terminal boxes not less than 1.6mm thick of reqd size and with top cover 3mm thick of plastic laminated sheets of required colour complete,including 1.5 Sqmm PVC ,FRLSH cableinsulated unsheathed multi stranded copper earth wire to the common earth and connecting to earth dolly,including colour coding of cable shall be Phase-red,Neutral-black and Earth- green with all accessories and complete all as specified and directed.Note :-(i) In case of roof/ceiling, heavy duty PVC pipe shall be used without any extra cost. (ii)The quoted rete is deemed to be included for the chases cutting. (iii) Cutting chases for concealed shall be made good using CM 1:4 and surface finished to match the existing surface & colour. 110 M&L for point wiring complete for One 5 pin 5 Amp switch socket out let point on an independent board with PVC insulated and unsheathed FRLSH cable1.5 sqmm (nominal area), ISI marked,multi stranded copperconductor cable including ISI marked not less than 20mm dia medium grade PVC conduit concealed in wall , MS conduit in roof/floors, factory made pressed steelconcealed terminal boxes not less than 1.6mm thick of reqd size and with top cover 3mm thick of plastic laminated sheets of required colour complete,including 1.5 Sqmm PVC ,FRLSH cableinsulated unsheathed multi stranded copper earth wire to the common earth and connecting to earth dolly,including colour coding of cable shall be Phase-red,Neutral-black and Earth- green with all accessories complete for max four nos socket outlets all as specified and directed. Note :-(i) In case of roof/ceiling, heavy duty PVC pipe shall be used without any extra cost. (ii)The quoted rete is deemed to be included for the chases cutting. (iii) Cutting chases for concealed shall be made good using CM 1:4 and surface finished to match the existing surface & colour. 111 M&L for point wiring complete for One 5 pin 5 Amp switch socket out let point on an same board with PVC insulated and unsheathed FRLSH cable1.5 sqmm (nominal area), ISI marked,multi stranded copperconductor cable 1100 volt grade, including ISI marked not less than 20mm dia medium grade PVC conduit concealed in wall , MS conduit in roof/floors, factory made pressed steelconcealed terminal boxes not less than 1.6mm thick of reqd size and with top cover 3mm thick of plastic laminated sheets of required colour complete,including 1.5 Sqmm PVC ,FRLSH cableinsulated unsheathed multi stranded copper earth wire to the common earth and connecting to earth dolly,including colour coding of cable shall be Phase-red,Neutral-black and Earth- green with all accessories complete for max four nos socket outlets all as specified and directed. Note :-(i) In case of roof/ceiling, heavy duty PVC pipe shall be used without any extra cost. (ii)The quoted rete is deemed to be included for the chases cutting. (iii) Cutting chases for concealed shall be made good using CM 1:4 and surface finished to match the existing surface & colour. 112 M&L for point wiring complete forOne light/Fan/Exhaust fan/Bell point on an independent board controlled by one switch with PVC insulated and unsheathed FRLSH cable2.5 sqmm (nominal area), ISI marked,multi stranded copperconductor cable 1100 volt grade, including ISI marked not less than 20mm dia medium grade PVC conduit concealed in wall , MS conduit in roof/floors, factory made pressed steelconcealed terminal boxes not less than 1.6mm thick of reqd size and with top cover 3mm thick of plastic laminated sheets of required colour complete,including 2.5 Sqmm PVC ,FRLSH cableinsulated unsheathed multi stranded copper earth wire to the common earth and connecting to earth dolly,including colour coding of cable shall be Phase-red,Neutral-black and Earth- green with all accessories and complete all as specified and directed.Note :-(i) In case of roof/ceiling, heavy duty PVC pipe shall be used without any extra cost. (ii)The quoted rete is deemed to be included for the chases cutting. (iii) Cutting chases for concealed shall be made good using CM 1:4 and surface finished to match the existing surface & colour. 113 S&F switch flush type 5/6 Amps single pole one way complete all as specified and directed. 114 S&F Socket outlet, flush type 2 in 1, 3 pin, 5/6 Amps complete all as specified and directed. 115 S&F Switch socket combination 2 in 1flush type 5/6 Amp 5 Pin complete all as specified and directed. 116 S&F Switch socket combination 5 in 1, 15 Ampflush type complete all as specified and directed. 117 Supply and fix electronic fan regulator 5 stepped type complete all as specified and directed 118 S&F ceiling rose PVC/Poly carbonate isolated body three terminal AC 230 volts complete all as specified and directed. 119 M&L submain wiring with two single core 6 sqmm FRLSH copper conductor, PVC insulated, multistranded, unsheathed cable ISI marked drawn in PVC conduit concealed in wallsurface / ceiling for sub main connection including one 6 sqmm FRLSH one single core PVC insulated multistranded unsheathed copper conductor used as earth wire to common earth and connection to earth dolly complete all as specified and directed. Note:- Two single core 6 sqmm copper conductor for phase / neutral, one run PVC conduit and one run of 6 sqmm earth wire shall be considered & measured as one unit. 120 Supply and fixing of VTPN DB 12 way suitable for Mounting MCCB as Incomer of rating 100 Amp with suitablerated bus bar having IP-43 protection and double metal door includingMCCB 100 Amps, AC, 415 Volt, 4 Pole, 16 KA with thermal magnetic trip unit (TMTU) adjustable thermal setting 0.7 - 1 x In, class II front face, Ics = 100% Icu as per IS/IEC 60947-2 including connection with aluminium thimbles as required complete all as specified. 121 Supply and fixing of MCB distribution board SPN 240 Volt 8 way with 200 Amp rated bus bar having IP-43 protection and double metal door concealed in wall including connection with aluminium thimbles as required complete all as specified. 122 S&F of MCB SPN 40-63 Amp 240 volt Ccurve 10 KA complete all as specifed and directed. 123 S&F of MCB SP 10 to 32 Amp 240 Volt C curve 10 KA complete all as specified and directed. 124 Supply and fixing LED lights fitting 4 Ft, 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. 125 S & F building security LED Light 30 Watt made up pressure die-cast aluminium housing with high power LED as lighting source and lens embedded PC having top opening separate driver compartment with IP-65 protection and impact resistance of IK 07 for building secuity purpose with bracket size made of GI pipe medicum grade 40 mm dia 1.5 mtr long bend to shape as required and fixing with two nos MS Clamp of size 40x6 mm for fixing of builiding security light fittings completed all as specified and directed. 126 Supply and fixing ceiling fans complete with blades, down rods (as per site requirement), electronic regulator and accessories, 230 V, 1400 mm sweep min air delivery 245 CFM with service value 6.00 BEE five star rated with brushless direct current motor (BLDC) complete all as specified and driected. (Note:- Additional length of down rods are also included.) 127 Supply and fixing of exhaust fan, steel body AC single Phase 230V of size 380m sweep with, blades, and frame and louvers including complete fitting into the wall and all as specified and directed. 128 Supply and Laying cable XLPE Insulated screened PVC bedded, galvanized steel strip armoured service cable pole to building electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 Sqmm 3.5 Core complete all as specified and directed. 129 S & F40 mm bore GI Tubing light grade with all fittings laid across road, in trenches or across PCC drain, along electric pole or floor/wall for cable protection with suitable size of MS Clapms and nut and bolts/washer complete all as specified and directed. 130 Supply & laying sand cushioning to under ground cable in layers of 23 cm thick (8 cm before laying the cable and 15 cm thick after laying the cable, punned thickness shall be measured) in trenches complete all as specified and directed.Note: - Only punned thickness shall be measured and paid. 131 M&L for protection to cable with well burnt sub class B bricks laid dry flatbrick,width equal to length of brick complete all as specified and directed. 132 S&F of metal plug & socket DB with metal plug and MCBs single pole enclosere with a two pin earth plug and socket suitable for 20 Amp complete with one single pole MCB complete all as specified and directed. 133 M & L Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground.(earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr. belowground level connecting to galvanised earth lead wire 4.0 mm diaas earth lead upto 7.5 meters long connected by means of bolts, check nuts and washers of GI and earth wire protected by provision of GI pipe medium grade, 15 mm bore including provn of concrete pit in PCC (1:2:4) type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4Kg/Sqm) and frame of angle iron 40 x 40 x 3mm fixingwith 6mm dia MS bar handle made to shape, GI light grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge plate, common salt and charcoal filling, with fixing arrangement, funnel, wire mesh and earth work in hard / dense soil, returning filling in and removal of surplus soil to a distance not exeeding 50 mtr, all as per electrical plate No 3 of SSR 2009 Part-I and connection all as specified and testing on completion. Note: The cost of excavation and earth work, PCC pit and pit covers, funnel and watering pipe, wire mesh, charcoal dust and common salt,20/ 40mm dia, medium grade, GI pipe as protection to GI wire 4.0 mm as main earthing lead from earth electrode to main TPN MCCBs DB/MCB DB/ test point length not less than 7.5mtrs) shall be deemed included in the unit rate for earthing and testing complete all as specified and directed .

BRR:7510190 Improvement of Bhamun T.E under RIDF-XXX of NABARD for the year 2024-25.-- 1 Clearing and grubbing road land including uprooting rank vegetation, grass, bushes , shrubs , saplings and trees girth upto 300mm , removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable materials to be used or auctioned up to lead of 1000m including removal and disposal of top organic soil not exceeding 150 mm thickness. 2 Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m transporting to site, spreading, grading to required slope and compacting to meet requirement of Table 300.1 and 300.2 with a lead upto 1000m as per Technical Specification Clause 301.5 (i) Private Land 3 Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads , transporting to site, spreding , grading to required slope and compacted to meet requirement of Table(300-2) with lead upto 1000m as per Technical Specification Clause303.1. (i) Private Land 4 Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface , mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density , complete as per cl.401.(ii) For Grading II Material 5 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stagesto proper grade and camber , applying and brooming requisite type ofscreening/ binding material to fillup the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per Technical Specification Clause 405. 6 Providing and laying interlocking concrete block pavement having thickness 80 mm as per Tech. Sp. Clause 1504 complete including carriage. b) Excluding Edge block / Edge Restraints 7 Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as perdrawings and Technical Specification Clause 801 (i) 600 mm equilateral triangle 8 Providing RCC Slab Culvert- 5 Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavated earth to the extent required and utilising the remaining earth locally for road work. (I) Ordinary soil (A) Manual means( Depth upto 3.00m) 9 Sand filling in Foundation Trenches as per Drawing & Technical Specification 10 Plain/Reinforced cement concrete in open foundation complete as per drawing and technical specification including steel shuttering formwork. A. PCC Grade M 20 ,Nominal mix (1:2:4) 11 Providing weep holes in Brick masonry/Plain/Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V:20H towards drawing foce complete as per Technical Specification. 12 Plastering with cement mortar (1:4), 15mm thk 13 Supplying,fitting and placing TMT bar reinforcement (Fe 500 D ) reinforcement bar (from primary producer: TATA/SAIL/Esser Steel/Jindal steel/Shyam steel/RINL) in substructure complete as per drawings and technical specification Clauses 1002,1005,1010 & 1202 14 Plain/Reinforced cement concrete in substructure complete as per drawing and technical specification Clauses 802,804,805,806,807,1202 and 1204 RCC Grade M 20i) for height upto 5 m 15 1000 mm dia NP3 Hume pipe culvert of 7.50 m length- 3 nos Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out , construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m , dressing of sides and bottom and back filling in trenches with excavated suitable material. 16 Plain Cement Concrete M10(1:3:6 nominal mix)in levelling course below open foundation of Head Walls as per drawings & Technical Specification Clause 1109 17 Laying 1st Class bedding on well compacted sand,moorumas per clause 115(ii) Granular bedding 18 Brick masonry work in cement mortar in foundation of head walls complete as per drawing and Technical Specification Clause 1109 (in Deduction of Hume pipe) 19 Providing and laying reinforced cement concrete pipe NP3 for culverts on fiurst class bedding of granular material in single row including fixing collar with cement mortar 1;2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B)1000mm dia 20 Plastering with Cement mortar (1:6) 15 mm thick on brick work in substructure as per Technical Specification 21 1000 mm dia NP3 Hume pipe culvert of 5.00 m length- 1 nos Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out , construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m , dressing of sides and bottom and back filling in trenches with excavated suitable material. 22 Plain Cement Concrete M10(1:3:6 nominal mix)in levelling course below open foundation of Head Walls as per drawings & Technical Specification Clause 1109 23 Laying 1st Class bedding on well compacted sand,moorumas per clause 115(ii) Granular bedding 24 Plain /reinforced cement concrete in Substructure complete as per Drawing and technical specification clause802,804,805,806,807,1202 & 1204.A) With crushed stone II) PCC grade M-20 (ii) Nominal Mix (1:2:4) 25 Providing and laying reinforced cement concrete pipe NP3 for culverts on fiurst class bedding of granular material in single row including fixing collar with cement mortar 1;2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B)1000mm dia 26 600 mm dia NP3 Hume pipe culvert of 7.50 m length- 1 nos Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out , construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m , dressing of sides and bottom and back filling in trenches with excavated suitable material. 27 Plain Cement Concrete M10(1:3:6 nominal mix)in levelling course below open foundation of Head Walls as per drawings & Technical Specification Clause 1109 28 Laying 1st Class bedding on well compacted sand,moorumas per clause 115(ii) Granular bedding 29 Plain /reinforced cement concrete in Substructure complete as per Drawing and technical specification clause802,804,805,806,807,1202 & 1204.A) With crushed stone II) PCC grade M-20 (ii) Nominal Mix (1:2:4) 30 Providing and laying reinforced cement concrete pipe NP3 for culverts on fiurst class bedding of granular material in single row including fixing collar with cement mortar 1;2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. 31 600 mm dia NP3 Hume pipe culvert of 5.00 m length- 1 nos Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out , construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m , dressing of sides and bottom and back filling in trenches with excavated suitable material. 32 Plain Cement Concrete M10(1:3:6 nominal mix)in levelling course below open foundation of Head Walls as per drawings & Technical Specification Clause 1109 33 Laying 1st Class bedding on well compacted sand,moorumas per clause 115(ii) Granular bedding 34 Plain /reinforced cement concrete in Substructure complete as per Drawing and technical specification clause802,804,805,806,807,1202 & 1204.A) With crushed stone II) PCC grade M-20 (ii) Nominal Mix (1:2:4) 35 Providing and laying reinforced cement concrete pipe NP3 for culverts on fiurst class bedding of granular material in single row including fixing collar with cement mortar 1;2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106.

BRR:7509859 Tender For GVH Repair vill - Kakrala-1. [10.35.1]FLAT BRICK OR TILE FLOORING 1. Providing and laying of flat brick or tile flooring with bricks of class designation 7.5 laid in cement sand mortar 1:4 on 100 mm thick cement concrete 1:8:16 and 100 mm sand filling and cement pointing 1:2 on top. [Through Rate] 2. [10.63.2]Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 2. Size of Tile 600x600 mm [Through Rate] 3. [10.67.2]Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours and shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement and matching pigments etc. complete. 2. Size of Tile 600x600 mm [Through Rate] 4. [11.5.3]12 mm cement plaster of mix : 3. 1:4 (1 cement: 4 fine sand) [Through Rate] 5. [11.57]Providing and laying average 6mm thick POP Coating on walls, Ceiling, beams and lintels etc. complete in all respects as approved by the Engineer-In-Charge. [Through Rate] 6. [11.97.1]Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : 1. Two or more coats applied on walls @ 1.25 litre/10 sqm over and including one coat of Special primer applied @ 0.75 litre /10 sqm [Through Rate]

BRR:7509744 Tender For Pabarsa To Daurala Road Remaining Part - Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smoothwheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per Technical Specification Clause 405. 2 Providing and applying primer coat with bitumen emulsion SS-2 on prepared surface of granular Base including cleaning of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means. Including supply of all Material, Labour, T&P etc also includinglabour cess, royalty and all other applicable Taxes (But excluding GST) required for proper completion of work as per direction of Engineer-in-charge. Technical Specificaton Clasue 502. 3 Providing and applying tack coat with bitumen VG-10 grade usingpressure distributor at the rate of 0.25 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom. Including supply of all Material Labour, T&P etc also including labour cess, royalty and all other applicable Taxes(But excluding GST) required for proper completion of work as per direction of Engineer-in-charge. Technical Specificaton Clasue(SI.NO. 503). 4 Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates using VG-10 Bitumen required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling witha three wheele80-100kn static roller capacity,finished to required level and gradesto be followed by Type-C seal coat. Including supply of all MaterialLabour, T&P etc also includinglabour cess, royalty and all other applicable Taxes(But excluding GST) required for proper completion of work as per direction of Engineer-in-charge.as per Technical Specification Clause. 508.Including supply of all Material Labour, T&P etc also including labour cess, royalty and all other applicable Taxes(But excluding GST) required for proper completion of work as per direction of Engineer-in-charge. Technical Specificaton Clasue(SI.NO. 503). 5 Providing and laying Type-C seal coat with VG-10 bitumen sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type C. Including supply of all Material Labour, T&P etc also including labour cess, royalty and all other applicable Taxes (But excluding GST) required for proper completion of work as per direction of Engineer-in-charge.as per technical specification clause 510. 6 Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 7 Brick lining on both side of the road of M-150 Bricks 7cm wide 11cm deep laid with mud mortar including labour & supply of Brics finished to the required templet and in proper alignment and also including Drassing and ramming the Excavated earth by the Engineer- Incharge 8 Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. 9 Providing concrete for plain/reinforced concrete M-15 in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 10 Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in Foundation,Sub-Structure & Super-Structure complete as per Drawing and Technical Specifications. 11 Providing and laying Reinforced Cement Concrete M-25in Foundation & Superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 12 Providing concrete for plain/reinforced concrete M-20 in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 13 Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smallersize towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specificationClause 1204.3.8 14 Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 110 mm dia PVC pipe & 6kg/sqcm (ISI Marked), extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications. As per SOR 30(A)

BRR:7509721 Tender For Under District Ayodhya ,Construction Of Library At Kisan Inter College, Lot No 8 - Work 2 Ist class brick work 1:6cement: coarse sand mortar in super structer D.S.R.6.4.2 3 Laying of R:C:C work 1:1.5:3 with cement: coarse sand & 20mm stone grit D.S.R.5.2.2 4 Laying of R:C:C work 1:1.5:3 with cement: coarse sand & 20mm stone grit in slab D.S.R.5.3 5 Mild steel cutting & binding D.S.R.5.22.6 6 12mm thick plaster in 1:6 cement fine sand mix mortar in plinth ( inner side) DSR 13.1.2 7 S/F M.S or iron work for fabrication of door / window frame DSR 10.25.2 8 P:C:C work in 1:2:4 for Hold fast DSR 4.20.2D 9 S/fixing of 30mm thick plywood door & window shutterDSR 9.20.1 10 Ms iron work for Fabrication of Z section window panel DSR 10.25.2 11 Glass pan with putty and nails D.S.R.14.5.2 12 Supply & fixing of SS mosquito proof jali withwooden beadings and nailsDSR9.51.1 13 Providing &appliying of 1mm thick cement base putty DSR 13.80 14 Finishing walls with Premium Acrylic Smooth Eterior Paint with Silicone additives of requred shadeDSR 13.46.1 15 Wall Painting with Plastic Emulsion Paint of Aapproved Brand All Complete SOR SI .No. 13.83.2. 16 Painting on G.S sheet with synthetic enamel paint 2 coat Painting with 1 coat priming coatDSR 13.53.1 17 Providing &laying of vitrified floor tiles 600x600mm with laid on 20mm thick cement mortor 1:4 cement / coarse sand with joint grey slurry with all complete D.S.R. 11.41.2 18 Supply & fixing of Aluminium Tower bolt 10mm dia 100mm long DSR9.97.5 19 Supply & fixing of aluminium silding bolt with nuts & bolts 16mm dia 250mm long DSR9.96.2 20 Supply & fixing of Aluminium door Handle 10mm dia 125mm long DSR 9.100.1 21 S/F of 110mm dia pvc down pipe complete with rose heads bends as DSR 12.41.2 22 Supply & fixing of sign board 23 Wiring point for light with 1.5 sq.mm. FR PVC insulated multistrand single core copper conductor cable as earthwire drawn in side the conduit pipe on surface , complete with 14 SWG copper earth continuity wire , piano type switch and ceiling rose/angle/batten holder on 3mm thick phenolic laminated backlite sheet etc. complete in all respects, as directed . Asper D.S.R. No. 1.10.3 24 Wiringpoint for Plug points with 1.5 sq.mm. FR PVC insuleted multistrand single core copper conductor cable inheavy gauge rigid FR PVC conduct pipe on surface complete with 14 SWG copper earth continuity wier and piano type switch and socket etc.complet in all respects. Asper D.S.R. No.1.13 25 Supply and wiring of submain 20mm dia heavy duty (2mm thick) PVC condure with 1no. 1.5 sq.mm. FR PVC insulated 1100V grade multistrand single core copper conductor cableas earth continuity wire drawn inside the conduit. complet in all respects. As per D.S.R. No. 1.14.1 26 Supply and wiring of submain with 20mm dia heavy duty (2mm thick) PVC condute with one no. 2.5sq.mm. FR PVC insulated multistrand single core copper conductor cable as earth continuity wire drawn in conduit . As per D.S.R. No. 1.14.2 27 Supply and wiring of submain with 25mm dia heavy duty (2mm thick) PVC condute with two no. 4sq.mm. FR PVC insulated multistrand single core copper conductor cable as earth continuity wire drawn in conduit . As per D.S.R. No. 1.14.3 28 Supply and fixing of Angle Holder/batten Luminaires complete. As per D.S.R. No. 1.58 29 Supply and fixing of 4way TPN distribution board without MCB with additional metal door complete in all respeet. As per D.S.R. No. 2.4.1 30 Supply and fixing of 40Amp double pole Isoletor. As per D.S.R. No. 2.12.1 31 S/F of 6Amp to 32Amp MCB (10KA) asper D.S.R. No.2.10.1 32 S/F of electronic fan dimmer ( Regulator ) 120-280W on existing switch board including making connection material labour & T&P D.S.R. No. 1.25 33 Supply and fixing of 1200 mm sweep bee 5 star rated celling fan with all complete DSR 19.1 34 Erection & testing of ceiling fan and regulator etc excluding down rod complete in all respect D.S.R. No. 1.45 35 Supply& Fixing of LED tube Light Batten Fiting (1X22 Wat)D.S.R. No. 1.41

BRR:7508626 Tender For Sariya Bhurkura Road Road Km 03 Jalalpur Maidan Nala On 2X3x3m Span Box Culvert, Approach Road, Protection Work - Bridge Part (A)- Excavation for roadwork in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m 2 Sand Filling in Foundation Trenches as per Drawing & Technical Specification 3 Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days. SI. No. - 12.04 4 Plain/Reinforced cement concrete in sub-structure complete as per drawing and Technical Specifications 13.50 5 Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications. (RCC M-25) SI.No.12.08 6 Providing and laying of cut stone on Appran with 25x15x10 cm average size dressed cut stone as per SI No NS-1(in bedded in CC Appran concrete) 7 Furnishing and Placing Reinforced/ Prestressed cement concrete in sub-structure as per drawing and Technical Specification. ( Hight upto 5m) SI. No-13.05 F(p) 8 Supplying, fitting and placing HYSD bar reinforcement in sub-structure comlete as per drawing and technical specifications (Height up to 5m) SI.No.13.06 (1600 & 2200) 9 Proviaing and laying filter media with granular meterials / stone crushed aggregates satisfying the requirements laid down in clause 2504.0.0. of MORTH specifications to a thickness of not less than 600 mm with smaller size towards the wall and provided over the entire surface behind abutment , wing wall and return wall to the full height compacted to a firm condition complate as per drawing and Technical Specification SI. No-13.10 (behind abutment and wing wall) 10 Providing and laying Cement concrete wearing coat M-30 grade including reinforecement complete as per drawing and Technical Specifications SI. No-14.4 11 Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces SI.No.-8.8 12 Lettering and painting of culvert no. Plate 30x30cm of standard size with two coats of approved synthetic enamel paint and lettering as per PWD maintenance manual including cost of all materials, labour T&P etc. complete. SOR NS-4 13 Protection work (B)- Excavation for roadwork in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m 14 Providing and laying Filter material underneath pitching in slopes complete as per drawing and Technical specification 15 Providing and laying Pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and Technical specifications 16 Construction of KC drain on both side of road parties with cement concrete 1:4:8 (cement sand & 40mm gauge stone ballast) M-150 brick work with struck pointing 1:2 cement & fine sand mortar including supply of all material labour T&P etc. complet as required for proper completion of work 17 Construction of Chute drain average size 0.45x0.30m on the slope of embankment of approach from road surface edge to ground level with cement concret 1:4:8 ( cement sand and 40mm gauge coarse snad mortar and finished with struck Pointing 1:2 cement & fine sand mortar including supply of all material labour T&P etc. required for proper completion of work 18 ForApproach Road (c)- Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 19 Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 20 Providing, laying, spreading and compacting stone aggregates of 45-63mm Stone ballast to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory rollerin stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density. 21 Providing, laying, spreading and compacting stone aggregates of 22.4-53mm Stone ballast to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory rollerin stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density. 22 Providing and applying primer coat with SS1 grade bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70to 1.00 kg/sqm using mechanical 23 Providing and applying tack coat with bitumen VG-10 using bitumen pressure distributor at the rate of 0.35kg per sqm on the prepared bituminous surfacecleaned with Hydraulic broom as per Technical Speicification Clause 503 24 Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregatesusing Viscocity grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable hot mix plant of appropriate capacity not less than 200 tonnes/hour, laying and rolling with a smooth wheeled roller, finished to required level and grades. 25 Providing and laying of premix sand seal coat with HMP of appropriate capacity not less than 200 tonnes/ hours using crushed stone chipping 6.7 mm size and penetration bitumen of suitable grade 26 Construction of pataries with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 27 ForDivirsion D- Dismantling brick work or stone work in lime or cement mortar and including stacking of materials as directed by Engineer-in-charge within a distance of 60 meters(200 feet). 28 Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 29 Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 30 Providing, laying, spreading and compacting stone aggregates of 45-63mm Stone ballast to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory rollerin stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density. 31 For 1000mm dia HP NP 3 (SOR) 32 ROAD SAFTY (F)- Providing and erecting a W metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMCseries channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 811

BRR:7508625 Tender For Construction Of Naipurwa Link Road - Construction of Embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 Technical Specification Clause 303.1. (Cartage Earth) 2 Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavatorat OMC, and compacting with smoothwheelroller to achieve thedesired density, complete as per Technical Specification Clause 401. 3 Providing, laying, spreading and compacting stone aggregates of 63 to 45 mm to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smoothwheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per MORD Specification Clause 405. 4 Providing, laying, spreading and compacting stone aggregates of 53 to 22.4 mm to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smoothwheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per MORD Specification Clause 405. 5 Brick edging on both sides of the road of first brick class M--150 8 cm wide and 12 cm deep laid withmud mortar including labour & supply of brick finished to required template and in proper alignment and also including dressing & ramming the excavated earth as directed by the engineer in charge of the work Including material, labour and T&P etc proper completion of the work 6 Providing and applying primer coat with bitumen emulsion (SS-2) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70 kg/sqm using manual means. Clause 502 7 Providing and applying tack coat with Bitumen VG10 using bitumen distributor at the rate of 0.30 kg per sqm on the prepared surface cleaned with Hydraulic broom as per Technical Specification Clause 503. 8 Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates using bitumenVG10 to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat Type C as per Technical Specification Clause 508.including hire & POL of road roller etc. complete as per directed by E/I 9 Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type C as per Technical Specification Clause 510 10 Construction ofearthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 Technical Specification Clause 303.1. in Patri for earth work to painting portion(Cartage Earth) 11 Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.as per MORT&H specificationclause-(12.1) , 1200 and as per direction of E/I.[For Drain work]. 12 Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.As per SI. No 280. 13 C/R stone masonary in 1:3 one cement and Three corse sand mortar including supply of all materials, labour & tool & plants etc. required for proper completion of work. 14 Supplyof 350mm dia NP3 hume pipe. 15 Laying of 350mm dia NP3 hume pipe. 16 Struck cement pointing in 1:2 cement & fine sand motar including supply of all material, labour and T&P etc, required for proper completion of the work.

BRR:7507687 Tender For Material Purchase At Bsr 2025-26 In Rd And Mgnrega Scheme Gp Dhanau Material Purchase At Bsr 2025-26 In Rd And Mgnrega Scheme Gp Dhanau Material Purchase At Bsr 2025-26 In Rd And Mgnrega Scheme Gp Dhanau , Procurement Of Services & Material Pruchase At Bsr 2025-26Ingram Panchayat Materail At Bsr 2025-26 (Item No. 01 To 43 Material & 43 Labour And Services) - 1 PARTICULARS 2 Ghadla / Kankar / Jhajhra 3 Mortar - Soil / Mud Masala 4 Lime - Lime from brick kiln for masonry work 5 Cement 6 PPC 7 White Cement 8 FINE AGREEGATE 9 Sand / Gravel 10 Gravel - Local / LOCAL 11 Rakhi (FLY ASH) 12 Surkhi 13 Stone Dust (Stone Dust, used in masonry work) 14 Ballast of stone / brick (FOR OTHER THAN ROAD WORK) 15 Stone 40 MM measured (grit broken by hand) (wides cut 1/11) 16 Stone 40 MM grit (broken by crusher) (wides cut 1/11) 17 Stone 20 MM grit (broken by crusher) ) 18 Stone 12 /10 /6 MM Grit (Broken by Crusher) 19 Brick Ballast 20 Road Works Material (5 Km. Lead Including) 21 63-40 mm (Broken by Crusher) (Wides Cut 1/11) 22 63-40 mm (Broken by Hand) (Wides Cut 1/11) 23 90-45 mm (Broken by Hand) (Wides Cut 1/11) 24 Kaveri Rubbish (Wides Cut 1/6) 25 Gravel (Wides Cut 1/6) 26 Kankar (Wides Cut 1/6) 27 Binding Material ( PI 4-6) (Wides Cut 1/6) 28 Brick (22.5 X 11 X 7.50 cm) 29 First Class (I CLASS) 30 Second Class (II CLASS) 31 Soiling/Kharanja/Masonry Stone 32 Masonry Beradda (RR) 33 Masonry Radda (CR) 34 Kharanja Soling (for flooring work upto 15 CM height) 35 Kharanja Soling (for road Kharanja work upto 23 CM height) 36 Jodhpuri type stone strip/champ/katli pieces (length 2-3, width 10-12, pearl 2.5-3.5) 37 Stone arch (FLAKY MATERIAL)(3-4 THICK & LENGTH & WIDTH1-2) 38 Sandstone (DPC, SILL, COPING, LINTEL, TAND, ALMIRAH, ETC) 39 Upto 25 MM thickness 40 25 - UPTO 40 MM THICKNESS 41 40- 50 MM THICKNESS 42 50 - 75 MM THICKNESS 43 75 - 100 MM THICKNESS 44 100 -150 MM THICKNESS 45 FLOORING / STRIP PAINTING KATLA STONE 46 FLOORING KATLA UPTO 35 MM THICK , min. 3 sqft or more area 47 KATLA FOR STRIP PAINTING 60 -75 mm THICKNESS , min. 3sqft or more area 48 Unpolished Rough Kota Stone 49 Upto 900 sq.cm 50 Upto 901 to 2300 sq.cm 51 More than 2300 sq.cm 52 Polished Kota Stone (One Side Polished) 53 Upto 900 sq.cm 54 Upto 901 to 2300 sq.cm 55 More than 2300 sq.cm 56 Marble Stone (Makrana Adanga 20mm Thick) 57 Upto 900 sq.cm 58 Upto 901 to 2300 sq.cm 59 More than 2300 sq.cm 60 Marble Chips 61 Marble Powder 62 Marble Stone (Rajnagar II Quality/Local 20mm Thick) 63 Upto 900 sq.cm 64 Upto 901 to 2300 sq.cm 65 More than 2300 sq. cm 66 Single petam size 100 x 75 mm 68 Double petam size 125 x 75 mm 69 Stone slab 70 Up to 1.5 m length , minimum 40 mm thick 71 1.5 m to 2.40 m length, minimum 50 mm thick 72 2.4 m to 3.0 m length , minimum 6 5 mm thick 73 above 3.0 m length, minimum 75 mmthick 74 Precast Tiles / Blocks 75 glazed size 30 x 45 cm 76 Mosaic Size - 40 mm thick 77 Vitrified Size- 60 x 60 cm 78 interlock tiles / brick / block for road work 79 Cement Interlocking Block M - 30 grade , 60 mm Thick 80 Cement Interlocking Block M - 30 grade ,80 mm Thick 81 Cement Interlocking Block M - 30 grade , 100 mm Thick 82 FR PVC Insulated Copper Conductor Single Core Cable ISI Marked 83 1.50 Sq.mm. 84 2.50 sq. mm. 85 0.50 sq mm 86 1.00 sq. mm. 87 4.00 sq. mm. 88 6.00 sq. mm. 89 Local wood with fittings (for doors, windows and furniture) 90 Mango 91 Babul 92 Others 93 Factory made doors (30mm thick, solid core single leaf) 94 Structural steel 95 Iron (Tor steel Fe 415 / 500 for reinforcement) 96 Winding wire 18 yards 97 Iron girders 98 Conical iron / square bar / strip / angle iron) 99 Barbed iron wire (size 12 guage wire and 12 guage strad / 12 guage wire and 14 guage strad / 14 guage 100 Mesh 101 Iron mesh (24 gauge, 14 mesh) 102 Cement concrete mesh Akash Patal 40 mm thick 103 Glass 104 3 mm thick glass 105 Colour - Paint 106 Enamel Paint 107 Decolorant (Water Bound) 108 Lime - For Painting (Aras / Kali) 109 Primer (For Iron / Wood) 110 Petroleum Products 111 Diesel HSD 112 Mobil Oil 113 Bitumen Shalitex Board (25 mm thick) 114 Plain Sheet 115 G.I. Sheet 22 Gauge (0.80 mm) 116 G.I. Sheet 24 Gauge (0.63 mm) 117 M.S. Sheet 22 Gauge (0.80 mm) 118 M.S. Sheet 24 Gauge (0.63 mm) 119 Corrugated Sheet 120 G.I. Sheet 1 mm thick 121 GI Sheet 22 Gauge (0.80 mm ) 122 Aswests Cement Sheet 6 mm ( 2.5 / 2.75 x 1m) 123 Other Sheets 124 PVC Sheet 1 mm thick ( Coloured / Plain ) 125 Green Yellow Literof Expo Sheet (183 x 90 ) 126 Pipes 127 GI 15 mm dia ( B Class) 128 GI 20 mm dia ( B Class) 129 GI 25 mm dia ( B Class) 130 AC 75 mm dia 131 AC 100 mm dia 132 PVC 90 mm Diameter (with ring) 133 P.V.C. 110 mm. Diameter (with ring) 134 P.V.C. 140 mm. Diameter (with ring) 135 P.V.C. 110 mm. (2.5 kg / sq. cm) with coupler 136 Sanitary 137 Indian W.C. 138 Orissa W.C. 139 European W.C. 140 FOOT REST 141 Porcelain Urinal 430 * 350 * 300 mm with coupler, bracket and P.V.C. waste pipe 142 Wash - Basin 450 * 300 mm with coupler, bracket and P.V.C. Waste pipe 143 Stone Bore (S.W.) pipe 100 mm dia, 0.6m long, 144 C.P. Pillar Cock (dia 15 mm ) (IS MARK ) 145 C.P. Bibb Cock (dia 15 mm ) (IS MARK ) 146 125 mm dia CP GRATTING 147 R.C.C. NP3 Hume Pipe with Collar 148 1200 mm dia 149 1000 mm dia 150 750 mm dia 151 600 mm dia 152 450 mm dia 153 300 mm dia 154 Steel Conduit ISI MARKED 155 20 mm dia 156 25 mm dia 157 Charcoal 158 P.V.C. WATER TANK WITH COVER (Conforming to IS : 12701 - 1989) 159 13/0.20 mm Twin Car PVC Blank with Flange Flexible Copper Cable 160 Steel Fasteners 6 mm x 75 mm 161 PVC CONDUIT ISI MARKED 162 25 mm Diameter 163 20 mm Diameter 164 JUNCTION BOX 165 20 mm Two Way 166 20 mm One Way 167 25 mm Two Way 168 20 mm One Way(PVC) 169 MODULE GI BOX 170 For 3 Modules 171 For 2 Modules 172 MODULE BASE COVER & PLATE 173 For 2 Modules 174 For 3 Module 175 Module Switch One Way, ISI MRKED 176 SP 15 /16 Ampere 177 SP 5 /6 Ampere 178 Modular Socket Outlet, ISI MRKED 179 3 Pin 5 /6 Ampere 180 6 Pin 15 /16 Ampere 181 MCB DB 182 2+2way, SPN, Single door 183 2+4way, SPN, Single door 184 2+6way, SPN, Single door 185 GI Pipe (Medium grade) 186 15.00 mm dia 187 40.00 mm dia 188 Copper wire 8 SWG (4.00 mm dia) (0.117 kg/m) 189 CI/MS cover plate, attached to frame of locking arrangement etc

BRR:7506399 Repairs And Renovation To Polymer Mortar, Plaster, Flooring And Repainting Ground To 4Th Floor Passage At D D Bldg. In The Premises Of Old Custom House, Mumbai.

BRR:7506326 Tender For Civil Maintenance Work At Motherdairy Calcutta-Wbmdc/Pur/24-25/036-2 Providing & laying acid/alkali proof red mandana stone, 40mm thick dressing and cutting to the required size, applying acid/alkali resistant primer on base, fixing stone over cement sand mortar ( 1:2) mixed with acid proof powder, filling the joints with acid/alkali proof joint filling materials including machine polishing complete as directed (No wastage will be paid). 3 Providing and fitting aluminium plain sheet with necessary screws / nut bolts over vertical surface of exising sloped Asbestos corrugated roof of various shed as per direction of MDC representative. I) 0.405 mm (26 SWG) thick. 4 Providing and laying new tarfeltof approved make over existing cracked Asbestos corrugated sheet with hot bitumen as binding materials asper direction of MDC representative. 5 Thorough cleaning of RCC Roof, Asbestos Corrugated Sheet Roof along with inlets of Rain Water Pipes, Gutter etc. and removal of the same at suitable places as per direction of MDC Representative.

BRR:7506078 Construction of Toilet at RM RM Govt Hr Sec School in Singampunari Town Panchayat.(5 Seat); 1 Earth work open excavation and depositing on bank with in the initial lead of 10m and a lift of 2m in hard stiff clay, stiff block cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders etc., as per SS 20 A. TNDSS NO: 23 & 24 VI (S2) VI,VII 9,10with standard specifications. 2 Collection supply and filling of well gravel filling approved quarry including cost andConveyance of all materials to site and all labour charges for filling etc., Complete. 3 Plain Cement Concrete 1:4:8 Mix (one Part of cement, four Part of M- Sand and Eight Part ofaggrigate) using 40 mm size ISS HBG metal from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing. Laying and curing etc., complete as per TNDSS NO : 28 & VI (S2) VI (S5A) VII standard specifications as directed by Engineer incharge. 4 Supplying and erecting centering for sides and soffits including supports and strutting uptp 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90cmx60cm and 10 gauge stiffened, welded with mild steel angles of size 25mmx25x3mm for boarding laid over silver oak (country wood) joist of size 10cmx6.5cm dia spaced about 90cm centre to centre and supported by casuarina props of 10cm to 13cm dia spaced at 75cm centre tocentre etc.complete complying with standard specification and as directed by the departmental engineers. TNBP No.30 5 For Grade Beam 6 For Roof Beam&Slab 7 For Column,Sunshade 8 Reinforced Cement Concrete 1:1½:3 Mix (One Part of cement, one and half Part of M- Sand and three Part ofaggregate)using 20mm size ISS HBG metal machine crushed from approved quarry including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing but excluding cost of reinforcement etc.Complete with std.Specifications. TNDSS NO: 30 V, VI (S3), VII-3. 9 Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification. 10 Supplying and fabrication of steel and placing in position of TMT steel rods for RCC works as per design given including cost of steel and GI binding wire in all floors etc., complete complying with standard specification in TNDSS NO:97 V,VI (S6) VII (S6), VII-3. 11 Brick work in CM 1:5 (one cement & Five Crushed Stone Sand (M- Sand)) using II class ground moulded bricks of size 9 X 43/8X 2 3/4 including finishing, curing, etc., complete complying with standard specification - 100CFT 12 Plastering with cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 10mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications 13 Plastering in Cement Mortor 1:5 Mix (one cement, five M- Sand) 12mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications. 14 Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete 15 Fabricating, supplying and fixing in positon of SOLID PVC DOORS with frames of different sizes as per the specifications given below: PVC door frames made out of best quality PVC extruded section of 40mm * 58 mm * 2.50 mm +/- 0.3 mm thick, having multichamber cross section and duly reinforced with steel to be mitre cut at the corners and welded including providing tie rod at the bottom and necessary weather seal etc., and PVC door shutters made out of extruded plastic section of 60 mm * 24 mm size in the configruation of an A section for shutter frames and multi-chamber hollow plastic section of 200 mm *200 mm*1 mm (average thickness) with tongue and groove section for panels etc., with necessary holdfasts, rubber beedings, furniture fittings, locking arrangements etc., complete including dimantling the masnery, making chippings, holes in the RCC column, beam etc., wherever necessary with power drill to the extent required and redoing the same to the original condition after fixing etc., complete as per specifications and as directed by the dePart ofmental officers. 16 Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick laid in-situ and pointed with same coloured cement 17 Dadooing walls withGlazed tiles of sizes 300mm X 200mm X 6mm size of approved make and quality and colour Set in cement mortar 1:2 (One part of Cement and two part of Plastering Sand (P- Sand)) over 10 mm base layer plastering and pointing with white cement neatly as directed. 18 Supplying and fixing in Position of Indian Oriya pan type water closet with “P’’ or “S’’ trap to set inbrick jelly concrete 1:4:8 Mix concrete 10 cm thick using 20mm brick jelly and top finished with c.m. 1:3 mix 20mm thick without any leakage etc. complete. 19 Painting two coats for Interior surface with approved Interior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification 20 Painting Two Coats on new Iron works with best synthetic enamel paint of approved colour and quality – 10m2. 21 Wiring with 2x1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch and making good of the concealed portion with suitable colour for PVC concealed light (6 Points Per Coil) (For Rooms like Bath , Toilet,& Pump room etc..)(SD-26) 22 Supply and fixing of WT bulk head fitting with guard (Philips / Bajaj / Crompton / K. Lite) suitable for11W CFL lamp with CFL.(PWD standard data No.SD.83).

BRR:7505871 Tender For Annual Maintenance Work Of Transit Hostel. - Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar As per DSR-2023 (Item No. 15.7.4) 2 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm As per DSR-2023 (Item No. 15.23.1) 3 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.As per DSR-2023 (Item No. 2.8.1) 4 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources). : As per DSR-2023 (Item No. 4.1.8) 5 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) As per DSR-2023 (Item No. 6.1.2) 6 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) As per DSR-2023 (Item No. 6.4.2) 7 Half brick masonry with common burnt clay F.P.S. (non modular) bricksof class designation 7.5 in foundations and plinth in : Cement mortar 1:4 (1 cement : 4 coarse sand)As per DSR-2023 (Item No. 6.12.2) 8 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) As per DSR-2023 (Item No. 13.4.2) 9 15 mm cement plaster on rough side of single or half brick wall of mix : 1:6 (1 cement: 6 coarse sand) As per DSR-2023 (Item No. 13.5.2) 10 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. As per DSR-2023 (Item No. 22.5) 11 Supply & filling of Brick Bats in sunken portion of building including breaking. As per DSR-2023 (Item No. 0362) 12 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate. As per DSR-2023 (Item No. 11.3.1) 13 Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. As per DSR-2023 (Item No. 17.1.1) 14 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 , of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc complete. Size of Tile 600x600 mm. As per DSR-2023 (Item No. 11.41.2) 15 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete. As per DSR-2023 (Item No. 11.40) 16 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid As per DSR-2023 (Item No. 17.2.1) 17 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall 15 mm nominal outer dia. Pipes. As per DSR-2023 (Item No. 18.7.1) 18 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall 20 mm nominal outer dia. Pipes. As per DSR-2023 (Item No. 18.7.2) 19 Providing and fixing brass bib cock of approved quality : 15 mm nominal bore As per DSR-2023 (Item No. 18.15.1) 20 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal boreAs per DSR-2023 (Item No. 18.17.1A) 21 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal boreAs per DSR-2023 (Item No. 18.17.1) 22 Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White As per DSR-2023 (Item No. 17.18.1) 23 Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15 x 3 mm and nuts & bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides. As per DSR-2023 (Item No. 10.29.2) 24 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete As per DSR-2023 (Item No. 13.88) 25 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre. As per DSR-2023 (Item No. 13.41.1) 26 Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) As per DSR-2023 (Item No. 13.46.1) 27 Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm). As per DSR-2023 (Item No. 14.5.1) 28 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. As per DSR-2023 (Item No. 13.80) 29 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. As per DSR-2023 (Item No. 13.62.1) 30 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter As per DSR-2023 (Item No. 12.41.2) 31 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter As per DSR-2023 (Item No. 12.41.1) 32 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. As per DSR-2023 (Item No. 9.21.1) 33 Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. As per DSR-2023 (Item No. 10.31) 34 Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturers specifications & direction of Engineer in-Charge. 80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern. As per DSR-2023 (Item No. 16.91.2) 35 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. As per DSR-2023 (Item No. 18.48)

BRR:7505802 Tender For Construction of CC road from Idgah to Mominas shop in village Jivna Guliyan - Dismantling of old brick laid on edge Kharanja Including stacking of old Bricks complete all as per SI NI 3 of Chapter 20. 2 Earth work in cutting or in embankment in ordinary soil excavation to be in theform of regular pits not exceeding 0.50 M.for small works/ Abadi area. (where machine can not move ).As per SI No 253(a) Including 3.00 km lead. 3 Concrete with 4 cm. gauge brick ballast,Fine Sand & Cement, in proportion of 12:6:1 in foundation as S.I. N0-273. 4 M-150 ClassBrick worksin 1:4Cement & C/Sand mix mortar in Fdn complete as SI-305a 5 12mm thick plaster in 1:4 Cement & C/Sand mix mortar complete allas per SINo 584 6 CC 1:2:4 with Cement: C/Sand : 2 Cm Gauge Stone Grit as per SI No 279 a. 7 Construction of un-reinforced, with expansion and construction joint , plain cement concrete pavement, thickness as per design, over a prepared sub base with 43 grade cement or any other type as per Clause 1501.2.2 (1:1.5:3) Coarse and fine aggregates confirming to IS 383 maximum size of coarse aggregateincluding Cost of Polythene Sheet also including complete shifting of matrials & Concrete etc.(M-30) as SI No-new 9(1) of Chapter 20. 8 S/F Information /sign board i/c all comp. at site. 9 Deduction of Cost of Brick ballast Made by available old Bricks 10 GST

BRR:7505509 Repairs And Structural Strengthening To Waist Slab, Columns And Beams, Repairs To Plaster With Polymer Mortar, Treads And Risers, Doors And Windows And Repainting To Staircase Block At Dd Building In The Premises Of Old Custom House, Mumbai.

BRR:7505505 Tender For Repairs And Renovations To External Plaster, Polymer Mortar And Repainting With 5 Coat Paint To Lhs And Back Side Of B-Wing Building, Karwar Street Police Line Qtrs At Fort, Mumbai.

BRR:7505503 Tender For Construction To Repairs And Renovations To External Plaster, Polymer Mortar And Repainting With 5 Coat Paint To Front Side Of B-Wing Building, Karwar Street Police Line Qtrs At Fort, Mumbai.

BRR:7505502 Construction To Repairs And Renovation To Plaster, Polymer Mortar, Flooring And Dado, Repainting, Doors And Windows Of Various Rooms At Ground And 1St Floor Of B-Wing Karwar Street Police Line Qtrs, Fort, Mumbai

BRR:7504527 Tender For Supply of Construction Materials Fee 2025-26 - Ghadla/Kankar/Jhajhra3 Mortar-soil/mud masala4 Lime from Kali kiln for masonry work5 P.P.C.6 White cement7 Sand/gravel8 Gravel - Local9 Fly ash10 Surkhi11 Stone dust (in masonry work)12 40mm measured stone (grit broken by hand) (cut voids 1/11)13 40mm stone (broken by crusher) (cut voids 1/11)14 20mm stone (broken by crusher)15 12/10/6mm stone (broken by crusher)16 Brick aggregate17 63-40mm stone aggregate broken by crusher (cut voids 1/11)18 63-40mm stone aggregate broken by hand (cut voids 1/11)19 90-45 mm. Hand broken stone aggregate(Cut voids 1/11)20 Quarry rubbish(Cut voids 1/6)21 Gravel(Cut voids 1/6)22 Kankar(Cut voids 1/6)23 Binding material (PI 4-6)(Cut voids 1/6)24 I st class)25 II class26 Masonry Beradda (RR)27 Masonry Radda (CR)28 Kharanja soling (for flooring work upto 15cm height)29 Kharanja soling (for road/Kharanja work upto 23cm height)30 Jodhpuri type stone strips/arches/pieces of slabs (length 2-3, width 10-12, thickness 2.5-3.5)31 Flaky material (3-4) Thick & Length and Width 1-2)32 Upto 25mm thickness33 Upto 25-40mm thickness34 Upto 40-50mm thickness35 Upto 50-75mm thickness36 Upto 75-100mm thickness37 Upto 100-150mm thickness38 Flooring sheets upto 35mm Thick, min. 3 sqft or more Area39 Patio sheets 60-75mm thickness, min. 3 sqft or more Area40 Upto 900 sq cm41 Upto 901 to 2300 sq cm42 More than 2300 sq cm43 Upto 900 sq cm44 Upto 901 to 2300 sq cm45 More than 2300 sq cm46 Upto 900 sq cm47 901 Upto 2300 sq. cm48 Above 2300 sq. cm49 Marble Chips50 Marble Powder51 Upto 900 sq. cm52 From 901 to 2300 sq. cm53 Above 2300 sq. cm54 Single Paitam Size 100 X 75 mm.55 Double Paitam Size 125 X 75 mm.56 Up to 1.5 m Length, Minimum 40mm thick57 1.5 m to 2.40 m Length, Minimum 50mm thick58 2.4 m to 3.0 m Length, Minimum 65mm thick59 Above 3.0 m Length, Minimum 75mm thick60 Glazed Size-30X45 cm61 Mosaic Size-40mm Thick62 Vitrified Size-60X60 cm63 Cement Interlocking Block M-30grade, 60mm Thick64 Cement Interlocking Block M-30grade, 80mm Thick65 Cement Interlocking Block M-30grade, 100mm Thick66 Mango67 Acacia68 Others69 Factory made doors (30mm thick, solid core single leaf)70 Iron (Tor Steel Fe 415/500 for reinforcement)71 Winding wire 18 gauge72 Iron girders73 Conical iron/Square bar/Leaf/Angle iron74 Barbed iron wire(Size 12 guage wire and 12 guage strad/12 guage wire and 14 guage strad/14 guage75 Iron mesh (24 gauge, 14 mesh)76 Cement concrete mesh Akash Patal 40 mm thick77 3 mm thick glass78 Enamel paint79 Distemper (Water Bound)80 Lime - for painting (Aras / Kali)81 Primer (for iron / wood)82 Diesel HSD83 Movil oil84 Bitumen Shalitex board (25 mm thick)85 G.I. Sheet 22 Gauge (0.80 mm)86 G.I. Sheet 24 Gauge (0.63 mm)87 M.S. Sheet 22 Gauge (0.80 mm)88 M.S. Sheet 24 Gauge (0.63 mm)89 G.I. Sheet 1 mm thick90 G.I. Sheet 22 Gauge (0.80 M.M.)91 Asbestos Cement Sheet 6mm(2.5/2.75X1m)92 PVC Sheet 1mm thick (coloured/plain)93 Green Yellow Literof Expo Sheet(183X90)94 GI 15mm Diameter(B Class)95 GI 20mm Diameter(B Class)96 GI 25mm Diameter(B Class)97 AC 75mm Diameter98 AC 100mm Diameter99 PVC 90mm Diameter(with ring)100 PVC 110mm Diameter(with ring)101 PVC 140mm Diameter(with ring)102 PVC 110 mm.(2.5kg/sq.cm) with coupler103 Indian W.C.104 Orrisa W.C.105 European W.C.106 Foot Rest107 Porcelain lipped urinal 430*350*300 mm with coupler, bracket and PVC waste pipe108 Wash-Basin 450*300 mm with coupler, bracket and PVC waste pipe109 Stone furnace (S.W.) pipe 100 mm. diameter, 0.6 m. long110 C.P. pillar cock (dia 15 mm) (IS Mark)111 C.P. bib cock (dia 15 mm)(IS Mark)CP Grating of 112 125 mm diameter113 1200mm diameter114 1000mm diameter115 750mm diameter116 600mm diameter117 450mm diameter118 300mm diameter119 1.50 sq. mm.120 2.50 sq. mm.121 0.50 sq mm122 1.00 sq. mm.123 4.00 sq. mm.124 6.00 sq. mm.125 13/0.20 mm Twin core PVC sheathed flat flexible copper cable126 20 mm Diameter127 25 mm Diameter128 25 mm Diameter129 20 mm Diameter130 20 mm Two way131 20 mm, One way132 25 mm Two way133 20 mm One way (PVC)134 For 3 modules135 For 2 modules136 For 2 modules137 For 3 modules138 SP 15/16 Amp139 SP 5/6 Amp140 3 pin 5/6 Amp141 6 pin 15/16 Amp142 Steel fastener 6 mm x 75 mm143 2+2 way, SPN, single door144 2+4 way, SPN, single door145 2+6 way, SPN, single door146 15.00 mm dia147 40.00 mm dia148 Copper wire 8 SWG (4.00 mm dia) (0.117 kg/m)149 CI/MS cover plate, attached to frame with locking arrangement150 Charcoal151 PVC water tank with cover (as per IS:12701-1989)Corresponding)152 Equipment (with POL and Driver)

BRR:7502571 Tender For Construction Of Road And Drain From Praveen Mishras House To Pawan Mishras House In Ward No. 18 Journey Tola; 1 Earth work in excavation in foul positionsoil lead 50mt.& lift 1.5 mt. incl. lab. T&P etc all complete . 2 P/L of base concrete in 1:6:12 with cement, L-Sand and 40mm S/B including mat. Lab. T&P,etc all complete. 3 M 150 class brick work in 1:4 with cement &approved Course Sand mortar including supply all material and S.I.N. labor etc. 4 12mm thick cement plaster in 1:4 cement mortorwith 1cement and 4 course sand including etc. all complete of work. 5 Laying C.C in 1:2:4for top of drainwork.with cement, Course Sand20 mm & Stone Grit including supply of all material and labour etc. 6 E/w filling with cartage upto 10Kmincludingetc. all complete of work. 7 P/L ofFlat Solingincludingetc. all complete of work. 8 P/L of 125 micron polythineincluding etc. all complete of work. 9 S/LayingofGSB53.-9.5 mm thick S/Bupto 10Cm loose Layer including etc. all complete of work. 10 Consolidation ofGSBupto 10 cm thickloose layer by Road Rollerincluding etc. all.complete. 11 P/fixing ofRoad Barricating including etc. all complete of work. 12 P/LC.C in 1:1.5:3for roadwork.with cement, Course Sand20 mm & Stone Grit including supply of all material and labour etc. 13 C.C. CuttingGroveby Machanical Machineincluding all completion of work. 14 RCC Work with cement concrete (1:1.5:3) including all completion of work. 15 M.S or iron workin renforcement cutting bending , binding ,and placeing incl. etc. all.