Name of Work:- MOEI & Fans, RMO Pump Sets i/c Compound Lights at Type V Quarter at Safdarjung Development Area, New Delhi (SH- EI Works in Servant Quarter and Other Balance Work) | Sl. No. | Item Description | |
| 1 | Sub Head - I (Wiring Work)Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required(a) Group B | | 2 | Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required.a) Group B | | 3 | Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.a) 20 mm | | 4 | b) 25 mm | | 5 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel / PVC conduit as required.a) 3 X 1.5 sq.mm | | 6 | b) 3 X 4 sq.mm. | | 7 | c) 3 X 6 sq.mm | | 8 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. | | 9 | Supplying & fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \\"C\\" curve including connections, painting etc. as required | | 10 | Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required | | 11 | 6 Module (200mmX75mm) | | 12 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. | | 13 | 5/6 A switch | | 14 | 3 pin 5/6 A socket outlet | | 15 | 15/16 A switch | | 16 | 6 pin 15/16 A socket outlet | | 17 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). | | 18 | 6 way (4 + 18), Double door | | 19 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. | | 20 | Single pole | | 21 | Single pole and neutral | | 22 | Triple pole and neutral | | 23 | Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. | | 24 | Sub Head - II (Fittings & Fixtures)Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal(Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body. Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, remote (preferably mobile app based) for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required. | | 25 | 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum) | | 26 | Supplying and fixing two module stepped type electronic fan regulator on the existing piano type including connections but excluding piano plate etc. as required | | 27 | Supplying and replacement, installation, testing & commissioning of 250 mm sizes white body Sweep PVC body Fresh Air Ventilator Exhaust fan with louver shutter in the existing opening of toilet room/kitchen etc i/c connection with 1.5 sqmm FRLS PVC insulated wires and fibre sheets etc as reqd. | | 28 | Supplying, installation, Testing & Commissioning of LED Recessed/surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10%, P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) <19, Flicker free (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), life time of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast /Extruded aluminium Body including trim . | | 29 | 12 -15 watt | | 30 | Supplying, Installation, Testing and Commissioning of up and down 10 Watt LED light Warm White (Yellowish Tone), Wattage:10 Watts; Voltage: 200V AC; Size Name: 12CM, Finish Type: Powder Coated; Mounting Type: Wall Mount; Wattage: 6.0; i/c connection, testing etc. complete as required. | | 31 | Supplying, Installation, Testing and Commissioning of down 10 Watt LED light Spotlight with adjustable focus, Direct the light at any angle with 230 degree tilt and 360 degree rotation, 36 Degree beam angle, Premium Aluminum housing in White & Black, Longer life with 20,000 hours^, Super robust construction, Wide voltage protection from 160V – 360V and surge protection up to 2.5kV, No harmful UV radiation etc. complete as required. | | 32 | Supplying, Installation, Testing and Commissioning of 6 Watt LED light provides bright, white illumination suitable for outdoor environments, Stylish Design: Wall-mounted light with a sleek matt finish, adding a modern touch to any exterior décor, Up Down Lighting: Provides up and down lighting effects, enhancing the aesthetic appeal of your outdoor space, Dust Proof: IP20 grade dust-proof body ensures durability and minimal maintenance, even in challenging conditions with complete etc. as required. Please Enable Macros to View BoQ information |
|