|
| 1 | Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation, trenches, drains (Any width or square metre on plan), including dressing of sides and ramming of bottoms, lift upto any height, including getting out the excavated soil and disposal of surplus excavated soil as directed in all kinds of classification, of soils such as pick work, jumper work, blasting work saturated soils including chiseling or any other mixed variety of soils, dewatering and / or removal of slush and other incidentals within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. Any loss to the public or private property during the course of excavation shall be the sole responsibility of the contractor which shall have to be duly compensated by him at his own cost in all cases. |
| 2 | Providing and laying, mechanically mixed and vibrated cement concrete 1:5:10 (one cement : Five sand : Ten graded crushed stone aggregate 40 mm (forty millimeter) nominal size) including curing complete excluding the cost of form work in foundation and plinth including carriage of material within all leads lifts and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 3 | Random rubble masonry with hard stone of approved quailty in foundation and plinth including levelling up with cement concrete 1:6:12 (one cement : six coarse sand : twelve graded stone aggregate 20 mm nominal size) upto plinth level with Cement mortar 1:6 (1 cement : 6 coarse sand) including curing complete and carriage of materials with in all leads, lifts and other incidentals. |
| 4 | Providing form work with steel plates 3.15 mm ( three point fifteen millimetre ) thick welded with angle iron in frame 30x30x5 mm (Thirty millimetre x Thirty millimetre x five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in-situ reinforced concrete and plain concrete work including carriage of materials with in all leads, lifts and other incidentals. |
| 5 | Foundations, footings, bases of columns, etc. for mass concrete |
| 6 | Columns, pillars, posts and struts square, rectangular or polygonal in plan as required. |
| 7 | Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 8 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) mechanically mixed, vibrated and curing complete as required including carriage of materials with in all leads, lifts and other incidentals. |
| 9 | Reinforced cement concrete work in walls any thickness including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor all level excluding the cost of centering, shuttering, finishing and reinforcement in secified grade of reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) mechanically mixed, vibrated and curing complete as required including carriage of materials with in all leads, lifts and other incidentals. |
| 10 | Reinforced cement concrete work in Beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor all levels excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) mechanically mixed, vibrated and curing complete including carriage of materials with in all leads, lifts and other incidentals. |
| 11 | Providing tor steel reinforcement TMT bars of grade Fe-500 D or more ISI make high yield strength for reinforced cement concrete work including straightening, cutting ,bending, binding and placing in position and cost of binding wire complete up to floor all levels including carriage of material with in all leads, lifts and other incidentals complete as per direction and to the entire satisfaction of Engineer-in-Charge |
| 12 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in all shapes and sizes in cement mortar 1:6 (one cement : six sand) including curing complete and carriage of material with in all leads, lifts and other incidentals. |
| 13 | Providing Sal wood work in frames of doors, windows, clerestorywindowsandother frames, wrought framed and fixed in position with hold fast lugsor with dash fasteners of required dia & length ( hold fast lugsor dash fastener shall be paid for separately) including carriage of material with in all leads, lifts and other incidentals. |
| 14 | Providing and fixing Second class teak wood 35 mm thick glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws including carriage of material with in all leads, lifts and other incidentals. |
| 15 | Providing and fixing 35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size Second class teak wood wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws including carriage of material with in all leads, lifts and other incidentals. |
| 16 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete Fixed to openings /wooden frames with rawl plugs screws etc including carriage of material with in all leads, lifts and other incidentals. |
| 17 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys,complete with bolts, nuts, locking arrangement,stoppers, handles, including applying a priming coat of approved steel primer including carriage of material with in all leads, lifts and other incidentals. |
| 18 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10mm dia meter bolts,nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1cement :3coarses and:6 graded stone aggregate 20mm nominal size) including carriage of material with in all leads, lifts and other incidentals. |
| 19 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer all completeincluding carriage of material with in all leads, lifts and other incidentals. |
| 20 | Providing 0.63 mm thick with zinc coating not less than 275 gm/ m² corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required including carriage of material with in all leads, lifts and other incidentals. |
| 21 | Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks,bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete 0.63 mm thick with zinc coating not less than 275 gm/m²including carriage of material with in all leads, lifts and other incidentals. |
| 22 | Providing and fixing M.S BP sheet 1.66 mm to 2 mm thick in eaves board / facia / soffit / ceiling including cutting fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instructions of engineer in charge ( base members of steel work shall be measured and paid separtely including carriage of material with in all leads, lifts and other incidentals. |
| 23 | 15 mm (fifteen millimeter) thick cement plaster in single coat on rough / fair side of brick /concrete / stone wall for interior plastering for all floors including arises internal rounded angles chafers and / or rounded angles chamfers and / or rounded angles not exceeding 80 mm (eighty millimeters )In girth and finished even and smooth in cement mortar 1:6 (one cement : six sand ) including curing as required and carriage of material with in all leads, lifts and other incidentals. |
| 24 | Providing and laying boulder filling under floor tightly hand packed including carriage of material with in all leads, lifts and other incidentals. |
| 25 | Providing and laying 40 mm thick cement concrete flooring 1:2:4 (one cement : two sand : four crushed stone aggregate 20 mm nominal size) laid in one layer finished with a floating coat of a neat cement including curing as required and carriage of material with in all leads, lifts and other incidentals. |
| 26 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of material with in all leads, lifts and other incidentals. |
| 27 | Providing and fixing twin rubber stopper Stainless Steel hanging floor door stopper, ISI marked, with necessary screws etc. complete. with in all leads, lifts and other incidentals. |
| 28 | Applying priming coat With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 29 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications complete in all respect as per direction and satisfaction of Engineer-in-Charge. |
| 30 | Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture |
| 31 | Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture Please Enable Macros to View BoQ information |
