|
| 1 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 2 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50m outside the periphery of the area cleared. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 4 | 1:5:10 (1 cement : 5 fine sand derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 5 | Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand). |
| 6 | Providing and fixing in position 12mm thick bitumen impregnated fiber board conforming to IS: 1838, including cost of primer, sealing compound Grade-A in expansion joints. |
| 7 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 8 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. |
| 9 | Using flats 30x6mm for diagonal braces and central cross piece |
| 10 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 11 | 160 mm diameter pipe |
| 12 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 13 | Bend 87.5° |
| 14 | 110 mm bend |
| 15 | Shoe (Plain) |
| 16 | 110 mm Shoe |
| 17 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 18 | 160 mm |
| 19 | Grading roof for water proofing treatment with |
| 20 | Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) |
| 21 | Cement mortar 1:3 (1 cement : 3 coarse sand) |
| 22 | Painting with water proof paint of approved make and quality on the roof of terrace of the building etc. all complete as per direction of Engineer in Charge. |
| 23 | 15 mm cement plaster on rough side of single or half brick wall of mix : |
| 24 | 1:4 (1 cement: 4 coarse sand) |
| 25 | Neat cement punning |
| 26 | Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. |
| 27 | White washing with lime to give an even shade: |
| 28 | New work (Three or more coats). |
| 29 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 30 | One or more coats on old work. |
| 31 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-charge. |
| 32 | With cement mortar 1:4 (1 cement : 4 fine sand). |
| 33 | Providing and fixing High impact Polycarbonate multiwall sheets in available shade in an existing steel frame and fixing with gasket and galvanised screws of required dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete (excluding the cost of frame work), including cutting sheets to size and shape wherever required. |
| 34 | (a) with 6mm thick multiwall polycarbonate sheets |
| 35 | Providing and fixing chicken wire mesh of approved make and quality on the surface of damaged plaster surface, R.C.C. or brick work surfaces wherever required and fixing with nails, hooks before replastering or reconcreting the same etc. all complete as per the direction of Engineer-in-charge. |
| 36 | Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.) |
| 37 | Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge |
| 38 | Using grade 'A' sealing compound conforming to IS: 1834 |
| 39 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete (i) Flexible pipes |
| 40 | 40 mm diameter |
| 41 | Providing and fixing PTMT bib cock of approved quality and colour. |
| 42 | 15mm nominal bore, 86 mm long. Weighing not less than 88 gms. |
| 43 | Providing and fixing PTMT stop cock of approved quality and colour. |
| 44 | 15 mm nominal bore, 86 mm long. Weighing not less than 88 gms. |
| 45 | Providing and fixing PTMT pillar cock of approved quality and colour . |
| 46 | 15mm nominal bore, 107 mm long. Weighing not less than 110 gms. |
| 47 | Providing and fixing PTMT, push cock of approved quality and colour. |
| 48 | 15 mm nominal bore, 98 mm long. Weighing not less than 75 gms. |
| 49 | Providing and fixing PTMT grating of approved quality and colour (i) Circular type |
| 50 | 100 mm diameter nominal bore |
| 51 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. |
| 52 | 15 mm nominal bore with 45 cm length. |
| 53 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 54 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : |
| 55 | 300 mm dia. R.C.C. pipe |
| 56 | Providing and injecting approved grout in proportion recommended by the manufacturer into cracks / honey-comb area of concrete / masonry by suitable gun / pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-Charge. (The payment shall be made on the basis of actual weight of approved grout injected) |
| 57 | Stirrer mixed SBR Polymer (of approved make) modified Cement slurry made with Shrinkage Compensating Cement in concrete / RCC work. |
| 58 | Providing & Applying weather proof sealant on outer joints of approved make confirming to IS & directed by Engineer-in-charge |
| 59 | Sealant 25mmx10mm at joints |
| 60 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer, of required shade and colour all complete : |
| 61 | New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre |
| 62 | Finishing walls with water proofing cement paint of required shade : |
| 63 | New work (Two or more coats applied @ 3.84 kg/10 sqm). Please Enable Macros to View BoQ information |
