|
| 1 | M&L for complete removal of existing treatment incl preparation of wall surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint of required shade, Make Apex Ultima of Asian Paint or Long Life of Berger or Excel Everlast 12 of Nerolac, having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.67 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm, over application of wall care putty average thickness 1-2 mm thick at any location on old plastered or unplastered surfaces of walls complete all as specified and as directed. |
| 2 | Preparation of old surfaces of ceiling (plastered or unplastered) by brooming or steel wire brushing, scrapping down smoke spot moulds, moss efflorescent salts and trading oil greasy spot and applying one coat of white wash on ceiling complete all as specified and directed by Engineer-in-Charge.. |
| 3 | Preparation of old plastered surface of wall washing, rubbing down and stopping of distempered, painted surfaces and applying one coat of oil emulsion distemper of approved tints complete all as specified and directed by Engineer-in-Charge.. |
| 4 | M&L for complete removal of existing treatment incl preparation of wall surfaces and applying two coat of oil emulsion distemper of approved tints over plaster of paris putty of 1mm thickness incl one coat of primer over surface to prepare the surface even and smooth, complete all as specified and directed by Engineer-in-Charge.. |
| 5 | M&L for preparing existing treated surfaces of external walls/RCC surfaces/soffits of chajjas/roof projection/cantilivers/balcony etc including cornices and applying one coat of cement base paint as camouflage / ordinary pattern complete all as specified & as directed-by-engr-in-charge. |
| 6 | Preparation of old decorated wooden surfaces of any description, not otherwise described over 10cm width & girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. |
| 7 | M&L for preparation of old decorated steel surfaces of any description, not otherwise described over 10 Cm width & girth and applying one coat of synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge. |
| 8 | Taking down cement plaster on stone masonry/Brick Masonry incl racking out joints, hacking for key scrubbing down with water and direction by Engr- In Charge. |
| 9 | M&L for 15 mm rendering in CM 1:4 on fair face of brick work or on concrete surface finished even and fair with water profinfing compound (WPC) complete all as specified and directed.(WPC Measured seprately) |
| 10 | M&L for 10 mm rendering in CM 1:6 on fair face of brick work or on concrete surface finished even and smooth without using extra cement complete all as specified and directed. |
| 11 | M&L for 05 mm rendering in CM 1:3 on fair face of ceiling or on concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. |
| 12 | Supply only liquid water proofing compound ( For external new plaster surfaces) |
| 13 | M&L for preparation of new plastered surface of wall and applying Two or more coats of 100% Premium acrylic emulsion paint of required shade, Make Apex Ultima of Asian Paint or Long Life of Berger or Excel Everlast 12 of Nerolac, having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.67 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm, over application of wall care putty average thickness 2-3mm thick at any location on old plastered or unplastered surfaces of walls complete all as specified and as directed. |
| 14 | M&L for preparation of new plastered surface of wall and applying two coat of oil emulsion distemper of approved tints over plaster of paris putty of 1mm thickness incl one coat of primer over surface to prepare the surface even and smooth, complete all as specified and directed by Engineer-in-Charge.. |
| 15 | M&L for preparing new plastered surfaces of ceilings and applying three coats of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. This shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. About 1.3 Kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub resistant. Small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the last two coats of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by Engineer-in-Charge. |
| 16 | Dismantling fencing wire mesh, any type complete all as specified and as directed. |
| 17 | Dismantling of posts or struts (wood, steel or RCC) any section embadded in concrete, including taking out embedded portion and making good disturbed ground complete all as specified and as directed. |
| 18 | Supply only chain link MS galvanized fencing size or type all as specified by Engr-in-charge. |
| 19 | Fixing only chain link fencing including line wires any mesh size and type of standard rails complete all as specified and as directed. |
| 20 | S&F Hand rails, Post, Pillar, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running round bars, flat iron for doors, balusters, post, nosing to steps including embeding in concrete and Mild steel screw bolts with hexagonal or square heads at aone end and screwed the other to be fitted with washer and one hexagonal or square nut exc 15cm and n exc 22 cm long , screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc.,and similar work conforming toFe-290 Gde E-165 ®` |
| 21 | Excavation in post holes in any type of soil, n exc 0.50 cum in each post, getting out returning, filling in and ramming earth or broken rubble mix with earth around in layers n exc 25 cm watering and removing surplus soil to a distance n exc 50 M and making good surface and all as specified. |
| 22 | M & L cement concrete 1:3:6 of type C2 (using 40mm graded stone aggregate) as in filling and mass concrete and Concrete wall complete all as specified and directed |
| 23 | Dismantling structural steel work including doors gates but excluding framed truss etc complete all as specified and directed |
| 24 | S&F framed work as in gate etc of angle,tubular or other section with gusset plates, braces etc complete drilled for fixing of steel sheeting or other covering prepared for hanging or sliding with and including either hooks & hinges for steel hanging door fitings complete all as specified and as directed. |
| 25 | Dismantling of AC sheet (corrugated or semi corrugated etc) including AC ridges in large patches as in roof covering complete all as specified and as directed. |
| 26 | S&F Pre- painted galvaiume aluminum zinc coating GI based corrugated steel sheet 0.5 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping crews as specified complete all as specified and directed |
| 27 | S&F for hollow,rolled sections, MS Pipe as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conf to Fe-410-w or E -250 quality A complete all as specified and directed. |
| 28 | M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces including prepration of new steel surfaces of any description over 10cm girth or width complete all as specified and as directed. |
| 29 | Demolition of concrete in ground floors and paving n exc 15cm thickness (below or above ground level ) complete all as specified and directed |
| 30 | M&L for 75mm thick plain cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection finished even and smooth without using extra cement, including making joints to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:2 by weight complete all as specified and as directed. |
| 31 | M&L 100mm thick cement concrete type D-2, 1:4:8 (40mm graded crushed stone aggregate) finishing cement concrete surface even and smooth without using extra cement as specified and directed. |
| 32 | Demolition Stone slabs and tiles of any description or thickness in floors aprons etc laid dry or laid dry and pointed complete all as specified and directed |
| 33 | M&L for 60mm thickness machine pressed precast interlocking paver block any shape and size conforming to IS - 15658-2006 of M-40 grade with grey cement and no pigment complete all as specified and directed |
| 34 | M&L for sand filling 25mm thick under floors or in foundations inc. watering and consolidation |
| 35 | Demolition of brickwork or stone, PCC block, boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stone work and precast concrete articles complete all as specified and as directed. |
| 36 | M&L for precast-cement concrete block masonary with solid blocks type D-1 ,1:3:6 (20mm graded aggregates) exc 10 cm in width and setting in CM 1:4 ,complete all as specified and directed |
| 37 | Preparation of new surfaces of walls including cornices, pillars, etc (plastered or unplastered) by brooming or steel wire brushing, scrapping down smoke spot moulds, moss efflorescent salts and trading oil greasy spot and applying three coat of white wash on walls complete all as specified and directed by Engineer-in-Charge. |
| 38 | S&F in repair vitreous china squatting pan “ORISSA” pattern size 58X 44 (CM) star white Make :- Hindwar with P or S trap front or back inlet with integral foot rest (excl flushing cistern & flush pipe) & including connection to trap & to flushing pipe anti syphonage pipe etc complete including making good to floor complete all as specified & as directed. |
| 39 | S & F in repair 10 ltrs capacity PVC low level flushing cistern sleek plus single flush of colour star white Make :- Hindwar with inlet, float valve and handle with 32 mm dia PVC pipe 600 mm long complete all as specified and as directed. |
| 40 | Supply and fix in repair vitreous china wash basin white flat back size 630x450mm including cutting for and pinning in ends of brackets or erecting stand,waste coupling,32 mm bore PVC waste pipe of suitable length, and connection complete all as directed complete all as specified and as directed. |
| 41 | S&F including taking down looking mirror of size 600 x 450mm bevelled edge of selected quality Atul make or equivalent mounted on PVC frame and fixed to and incl wooden plugs with chormium plated brass screws cup washer complete all as specified and directed. |
| 42 | Supply and fixing CP corner glass shelf with bracket fixed with screws complete all as specified and as directed by Engineer-in-Charge. |
| 43 | S&F CP Brass soap dish fixed to wall with cp brass screws etc complete all as specified and as directed by the Engineer-in-Charge. |
| 44 | S & F in repair / new PVC connection, heavy duty 15 mm bore, 45 cm long with two Nos PTMT nuts at both ends of approved quality complete all as specified and directed |
| 45 | S&F in repair PVC Connections 15mm size with PTMT Nuts of length 600mm and fixed, complete all as specified and as directed. |
| 46 | Supply and fixing in repair PVC waste pipe with 32 mm bore and 65 cm long with cap complete all as specified and directed. |
| 47 | S&F in repair 15 mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed. |
| 48 | S&F in repair 15mm bore cast copper alloy chromium plated angle cock with flange complete all as specified and as directed. |
| 49 | S&F in repair 15mm bore fancy type chromium plated bib cock long body with flange etc complete all as specified and as directed. |
| 50 | S& F rotational moulded synthetic (HDPE) water storage tank 500litre capacity hoisted & fixed in position all as specified in SSR Part-I complete all as spd & directed. |
| 51 | S& F rotational moulded synthetic (HDPE) water storage tank 1000 litre capacity hoisted & fixed in position all as specified in SSR Part-I complete all as spd & directed. |
| 52 | Demolition and breaking up drain pipes (Salt glazed ware, AC/PVC/CI or Reinforced concrete) set in cement mortar in floors or wall in 100mm dia meter. |
| 53 | S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with clamp out of 25x3mm flate Iron including bolts and nuts 110mm bore. |
| 54 | S &F of 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors or wall and complete all as specified and directed. |
| 55 | S&F PVC (SWR) pipes single socketed, in any length with clamp out of 25x3mm flate Iron including bolts and nuts rubber ring joints, fixed to wall 75 mm bore complete all as specified and as directed. |
| 56 | S &F of 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors or wall and complete all as specified and directed. |
| 57 | S&F PVC (SWR) bends any radius 110mm bore complete all as specified and as directed. |
| 58 | S&F PVC (SWR) bends any radius 75mm bore complete all as specified and as directed. |
| 59 | Manufacturing, supplying and fixing Retroreflective regulatory sign board of size 900 mm dia meter made out of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated lens type retro -reflective sheeting as approved by Engineer-in-charge . Letter, symbols, borders etc. will be as per IRC - 67 with required colour scheme on the boards and with the high intensity grade A. The aluminium sheet to be riveted to M.S. frame of angle iron of size 40x40x4 mm. The boards will be fixed to 1 No. 50x50 mm square post made of M.S. angle 50x50x4 mm, 4 m long welded to the frame with adequate anti-theft arrangement .Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminium sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per direction of Engineer-in-charge. |
