|
| 1 | Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/Class -II of IS: 3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosivetreatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.. (Make: As per approved make list attached) |
| 2 | 150 mm. Dia |
| 3 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 1239/Class -II of IS: 3589 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : (Make: As per approved make list attached) |
| 4 | 100mm dia. |
| 5 | Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required. (Make: As per approved make list attached) |
| 6 | Single headed Stainless steel |
| 7 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : (Make: As per approved make list attached) |
| 8 | 100 mm dia |
| 9 | 150 mm dia |
| 10 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : (Make: As per approved make list attached) |
| 11 | 150 mm dia |
| 12 | Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required: (Make: As per approved make list attached) |
| 13 | 2 way-100 mm dia M.S. Pipe |
| 14 | 4 way-150 mm dia M.S. Pipe |
| 15 | Providing and Fixing of Exide Battery 12 Volts, 150 Amp for Diesel Generator Set in Medical Gas Plant Civil Hospital, Sector-45, Chandigarh. |
| 16 | Servicing of Kirloskar engine genset of 45KW/ 60 HP.1500 rpm with change of all oil filter, engine oil, servicing of engine including minor repair by entire satisfaction of EIC including testing on full load after servicing. The work also including testing of batteries, change of battery terminal, repair and testing of battery charger and replacement carbon assembly including carbon set of Genset. |
| 17 | Repair of jockey pump of size 32/26 head 80 mr. 15 KW including dismantling and refixing after repair the complete work need to be replacment of bearing bush impeller, and thrust plate with grease nut bolt, water seal, shaft work with entire satisfaction of EIC. Make Kirlosker. |
| 18 | Providing and fixing dual type pressure switch suitable for 1-20 Kg/cm2 including electrical connections setting of Cut-In and cut-Off pressure complete in all respects. Make:H.Guru/ Fiebig/ Dwyer |
| 19 | Replacement of PVC Nozzel against damage/ condumn/ irreparable of nozzel for rubber hoze reel piping including cost of clamp complete in all respect. Please Enable Macros to View BoQ information |
