Name of Work:- Renovation of multipurpose hall at Bal Bhawan in Distt. Rewari (Pdg. E.I. internal only). | Sl. No. | Item Description | |
| 1 | SITC of Fresh air fan 10` including all material required to complete the job in all respect upto entire satisfaction of Engineer-in-Charge of workMake: Bajaj / Orient / Crompton | | 2 | S/E Air Circulator wall fan 18` including all material required to complete the job in all respect upto entire satisfaction of Engineer-in-Charge of work.Make: Bajaj / Orient / Crompton | | 3 | Supply and erection of FRLS PVC insulated copper conductor flexible cable complete the job in all respect upto the Engineer-in-Charge of the work.Make: Havells / Polycab / R.R.1.5 Sqmm Single core wire | | 4 | Supply and erection of FRLS PVC insulated copper conductor flexible cable complete the job in all respect upto the Engineer-in-Charge of the work.Make: Havells / Polycab / R.R.4.0 Sqmm Single core wire | | 5 | LED Down lighter (SMD Type) (System lumen efficacy =120 (135 lm/Watt )Supplying, installation, Testing and Commissioning of LED Recessed /surface Down lighter (Round / square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency )85%, Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short and Open circuit protection ,THD ( 10% , P. F.=0.95, IP20, CRI )80 , UGR (Unified Glare Rating) ( 19, Flicker free (flicker should be below 5 %), life time (LED,Driver and electrical circuitry), life time of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) (3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. `complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy =120 (135 lm/Watt output . LM79 and LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C8-10 watt (New HSR 23.28.2.2) | | 6 | LED Panel light 2x2 ft. (System lumen efficacy =120 (135 lm/Watt)Supplying, installation, Testing and Commissioning of Panel light 2x2 ft., offollowing body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency )85%, Operating voltage AC 140- 270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short and Open circuit protection ,THD ( 10% , P. F.=0.95, IP20, CRI )80, UGR (Unified Glare Rating) ( 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver and electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends,CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) (3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy =120 (135 lm/Watt output . LM79 and LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C)CRCA Sheet Body (Thickness = 0.50 mm)40 watt (New HSR 23.28.7.11) Please Enable Macros to View BoQ information |
|