|
| 1 | GENERAL NOTESThis document shall be read in conjunction with doc. \\"SCOPE OF SUPPLY-ELECTRICAL\\" DOC ID TK-1P22A-EL-SPE-0022.Technical Specification for the equipment / material to be supplied by CONTRACTOR is included therein.For 'Limit of Variation' in the rates / quantities / total value of work, please refer 'SPECIAL CONDITIONS OF CONTRACT'.Refer the document 'MASTER SUPPLIER LIST' for the makes of equipment / material to be supplied by CONTRACTOR.For all the equipment (suitable for Explosive Atmospheres) to be supplied by CONTRACTOR, relevant certification from applicable recognised approving authority shall be provided. For CONTRACTOR supplied items mentioned below, procurement / supply clearance for the items shall be given to CONTRACTOR, in lots as per Project requirement. Subsequent to the receipt of procurement / supply clearance, CONTRACTOR may initiate the required action in this regard.CONTRACTOR should read entire specification to understand in totality the scope of supply and Installation. Every line item for Supplies and Installation should be read along with the respective Installation standard / hook up drawings related to that specific line item to understand the scope of supply and Installation in totality. Any miss outs in supply scope in this regard by the CONTRACTOR shall not be entertained.Scope shall also include Packing, forwarding and transport to site, unloading and storage in Contractor's warehouse. All Required insturctions shall be followed as per manufacterer recommandation for long term storage.The qouted rates shall include charges for Routine and Type testing, TPI, Packing, forwarding, Insurance, Transportation to site, supply of Mandatory spares, commissioning spares and special tools and tackles. |
| 2 | EQUIPMENT |
| 3 | LV PANELS (WALL / CONCRETE / STEEL STRUCTURE MOUNTED) |
| 4 | LDB / ELDB / DCLDB/ PDB (Industrial type )Supply of LDB / ELDB / DCLDB/ PDB Industrial type ) as per Technical specification for Industrial Equipment (Doc. no.TK-1P22A-EL-SPE-0074 ) |
| 5 | LDB / ELDB Lighting Distribution Board / Emergency Sub Lighting Distribution Board |
| 6 | 6 Way |
| 7 | 9 Way |
| 8 | 12 Way |
| 9 | 15 Way |
| 10 | 18 Way |
| 11 | 24 Way |
| 12 | DCLDB ( Critical Lighting Distribution Board) |
| 13 | 6 Way |
| 14 | PDB (Short time current rating : 9 kA for 1 sec)Auxiliary Power Distribution Board |
| 15 | 9 Way |
| 16 | 15 Way |
| 17 | PDB (Short time current rating : 20 kA for 1 sec)Auxiliary Power Distribution Board |
| 18 | 6 Way |
| 19 | 12 Way |
| 20 | 24 Way |
| 21 | UPSDB (115 VAC)Auxiliary Power Distribution Board |
| 22 | 24 Way |
| 23 | 24 Way with ATS |
| 24 | LDB / ELDB / DCLDB/ PDB (For Explosive Atmospheres) Supply of LDB / ELDB / DCLDB/ PDB ( For Explosive Atmospheres ) as per Technical Specification for Flameproof Equipment (Doc. no.TK-1P22A-EL-SPE-0019 ) |
| 25 | LDB / ELDB (Gas Group : IIC)Lighting Distribution Board / Emergency Sub Lighting Distribution Board |
| 26 | 6 Way |
| 27 | 9 Way |
| 28 | 12 Way |
| 29 | 15 Way |
| 30 | 18 Way |
| 31 | DCLDB (Gas Group : IIC)Critical Lighting Distribution Board |
| 32 | 6 Way |
| 33 | 9 Way |
| 34 | PDB (Short time current rating : 9 kA for 1 sec) (Gas Group : IIC)Auxiliary Power Distribution Board |
| 35 | 6 Way |
| 36 | 9 Way |
| 37 | 12 Way |
| 38 | 15 Way |
| 39 | 18 Way |
| 40 | NON UPS PDB FOR INSTRUMENTS (125 A, Short time current rating : 20 kA for 1 sec) (Gas Group : IIC) |
| 41 | PDB for Hydro Jet area (400A) (Gas Group : IIC) |
| 42 | LOCAL CONTROL STATIONS (LCS) |
| 43 | Supply of Local Control Stations as per doc. no. TK-1P22A-EL-SPE-0018 (Technical Specification for Local Control Stations) |
| 44 | LCS Industrial type |
| 45 | Type H1 : Industrial type weatherproof : Stop PB (Red) Mushroom type, with stay put feature, with pad locking facility, with 2NO+2NC contacts + ON lamp |
| 46 | LCS for Explosive Atmospheres |
| 47 | Type A3 : Flameproof (Gas Group : IIC) : Start PB (Green); Stop PB (Red) with stay put feature, shrouded type, with pad locking facility & each PB shall have 2NO+2NC contacts |
| 48 | Type B3 :Flameproof (Gas Group : IIC) : Start PB (Green, shrouded type); Stop PB (Red) Mushroom type, with stay put feature, with pad locking facility & each PB shall have 2NO+2NC contacts & Ammeter (1A, MI type) |
| 49 | Type D3 : Flameproof (Gas Group : IIC) : Start PB (Green, shrouded type); Stop PB (Red) Mushroom type, with stay put feature, with pad locking facility & each PB shall have 2NO+2NC contacts. With Local/ Remote Selector switch lockable in both the positions, Key shall be removable only in OFF position & Ammeter (1A, MI type) |
| 50 | Type F4 :Flameproof (Gas Group : IIC) : Start PB (Green, shrouded type); Stop PB (Red), shrouded type; Key lockable emergency stop PB (Red), Mushroom type, with stay put feature, with pad locking facility; each PB shall have 2NO+2NC contacts; Ammeter (4-20mA); Analog RPM meter (4-20mA); key lockable A-M selector switch; Speed Lower-Speed Raise Push buttons |
| 51 | Type F5 :Flameproof (Gas Group : IIC) : Start PB (Green, shrouded type); Stop PB (Red), shrouded type; Key lockable emergency stop PB (Red), Mushroom type, with stay put feature, with pad locking facility; each PB shall have 2NO+2NC contacts; Ammeter-2 Nos. (4-20mA); Analog RPM meter (4-20mA); key lockable A-M selector switch; Speed Lower-Speed Raise Push buttons |
| 52 | Type J3 :Flameproof (Gas Group : IIC) : Stop PB (Red), Mushroom type, with stay put feature, with pad locking facility & with 2NO+2NC contacts |
| 53 | Type L3 :Flameproof (Gas Group : IIC) :Trip-Neutral-Close (T-N-C) switch shall be spring return to neutral type from CLOSE position with two contacts each for time stamping & tripping signal. Switch shall be lockable in TRIP position. With Local/ Remote Selector switch lockable in both the positions, Key shall be removable only in OFF position & Ammeter (1A, MI type) (Configuration: T-N-C SWITCH + L/R SWITCH+ AMMETER ) |
| 54 | Type L4 :Flameproof (Gas Group : IIC) :Trip-Neutral-Close (T-N-C) switch shall be spring return to neutral type from CLOSE position with two contacts each for time stamping & tripping signal. Switch shall be lockable in TRIP position. & Ammeter (1A, MI type) (Configuration: T-N-C SWITCH + AMMETER + RUN INDICATION + TRIP INDICATION) |
| 55 | Type P3 :Flameproof (Gas Group : IIC) :Trip-Neutral-Close (T-N-C) switch shall be spring return to neutral type from CLOSE position with two contacts each for time stamping & tripping signal. Switch shall be lockable in TRIP position & Ammeter (1A, MI type) |
| 56 | ELECTRICAL HEAT TRACING SYSTEM |
| 57 | Supply of Heat Tracing System comprising Power Distribution Board-cum-Control Panel, Heat Tracers and Accessories (Connector, Junction Box, fastening material, etc.), Temp. sensing elements, Thermostats, etc. as per Specification (Doc no. TK-1P22A-EL-SPE-0031)The scope includes design, engineering, manufacturing, inspection and testing at vendor’s works, packing, forwarding, supply to site. |
| 58 | Unit rates for addition/ deletion of following items during detailed engineering. |
| 59 | Self regulating heat tracer |
| 60 | Power Limiting heat tracer |
| 61 | Mineral insulated heat tracer |
| 62 | Power Junction Box |
| 63 | End Junction Box |
| 64 | Multiple entry power connection and tee |
| 65 | Small pipe adaptor |
| 66 | Insulation Entry Kit |
| 67 | Thermostat (with Kit) |
| 68 | CABLES AND WIRES, GLANDING, TERMINATIONS AND CABLE ROUTING SYSTEMS |
| 69 | CABLES AND WIRESSupply of armoured / unarmoured power / control / lighting / earthing . Communication cables of various sizes as per technical specifications attached with the Tender |
| 70 | Earthing cablesSupply of MV / LV Cables as per the document attached elsewhere in the tender650/1100V Al / Cu conductor, PVC insulated, unarmoured earthing cables |
| 71 | 1 C x 6 sq.mm Cu Stranded, PVC insulated Green/Yellow cable |
| 72 | 1 C x 16 sq.mm Cu Stranded, PVC insulated Green/Yellow cable |
| 73 | 1 C x 25 sq.mm Cu Stranded, PVC insulated Green/Yellow cable |
| 74 | 1 C x 50 sq.mm Cu Stranded, PVC insulated Green/Yellow cable |
| 75 | 1 C x 95 sq.mm Cu Stranded, PVC insulated Green/Yellow cable |
| 76 | 1 C x 25 sq.mm Al Stranded, PVC insulated Green/Yellow cable |
| 77 | 1 C x 35 sq.mm Al Stranded, PVC insulated Green/Yellow cable |
| 78 | 1 C x 50 sq.mm Al Stranded, PVC insulated Green/Yellow cable |
| 79 | 1 C x 70 sq.mm Al Stranded, PVC insulated Green/Yellow cable |
| 80 | 1 C x 120 sq.mm Al Stranded, PVC insulated Green/Yellow cable |
| 81 | GI Wire ropes |
| 82 | 8 mm dia. GI wire rope |
| 83 | 10 MM (3/8\\") DIA G.I WIRE ROPE |
| 84 | 16 MM (5/8\\") DIA G.I WIRE ROPE |
| 85 | Supply of 650V / 1100V (Uo / U) voltage grade, Multistranded Cu conductor, PVC insulated, flexible cable, FRLS |
| 86 | 3C x 2.5 sq.mm |
| 87 | Supply of single Core, Annealed Tinned Copper Conductor, cables with Fiber Glass, (Uninyvin, cable size : 1C x 109 sqmm) |
| 88 | Ehernet Cable (UTP CAT6e Cable) |
| 89 | CABLE GLANDING AND TERMINATION (HV) |
| 90 | HV Cable glands Industrial type |
| 91 | Supply of cable glands HV cable glands industrial type and all the associated accessories as per 'ANNEXURE-II to SCC - SCOPE OF SUPPLY - ELECTRICAL'.CONTRACTOR shall be responsible selection and supply of exactly suitable cable glands for the actual cables (technical particulars as per project technical specification) installed at site and equipment cable entry tread.'OD' mentioned below indicate approximate overall cable diameters. |
| 92 | HV Cable gland suitable for 6.6 / 6.6 kV (UE) voltage grade, Al/Cu conductor, XLPE insulated, screened, armoured power cable |
| 93 | 3C x 240 sq.mm A2XCEFY (OD : 68 mm) |
| 94 | 1C x 630 sq.mm A2XCEWaY (OD : 70 mm) |
| 95 | HV Cable gland suitable for 33 / 33 kV (UE) voltage grade, Al/Cu conductor, XLPE insulated, screened, armoured power cable |
| 96 | 1C x 630 sq.mm A2XCEWaY (OD : 70 mm) |
| 97 | HV Cable glands for Explosive Atmospheres |
| 98 | Supply of cable glands HV cable glands industrial type and all the associated accessories as per 'ANNEXURE-II to SCC - SCOPE OF SUPPLY - ELECTRICAL'.CONTRACTOR shall be responsible selection and supply of exactly suitable cable glands for the actual cables (technical particulars as per project technical specification) installed at site and equipment cable entry tread.'OD' mentioned below indicate approximate overall cable diameters. |
| 99 | HV Cable gland suitable for 6.6 / 6.6 kV (UE) voltage grade, Al/Cu conductor, XLPE insulated, screened, armoured power cable |
| 100 | 3C x 240 sq.mm A2XCEFY (OD : 68 mm) |
| 101 | HV Cable termination kit |
| 102 | Supply of HV cable termination kit along with all the associated accessories and suitable tinned copper lug for cable termination at designated location.CONTRACTOR shall be responsible for selection and supply of exactly suitable cable termination kit for the cables (technical particulars as per project technical specification) as per the required site conditions and available termination arrangement, and as per the cable technical specification. |
| 103 | HV Cable termination kit Heat shrinkable type (suitable for indoor installation) for 6.6 / 6.6 kV (UE) voltage grade, Al conductor, XLPE insulated, screened, armoured power cable |
| 104 | 3C x 240 sq.mm A2XCEFY |
| 105 | 1C x 630 sq.mm A2XCEFY |
| 106 | HV Cable termination kit Heat shrinkable type (suitable for indoor installation) for 33 / 33 kV (UE) voltage grade, Al conductor, XLPE insulated, screened, armoured power cable |
| 107 | 1C x 630 sq.mm A2XCEWaY |
| 108 | CABLE GLANDING AND TERMINATION (MV) |
| 109 | MV Cable glands Industrial type |
| 110 | Supply of cable glands MV cable glands industrial type and all the associated accessories as per 'ANNEXURE-II to SCC - SCOPE OF SUPPLY - ELECTRICAL'.CONTRACTOR shall be responsible selection and supply of exactly suitable cable glands for the actual cables (technical particulars as per project technical specification) installed at site and equipment cable entry tread.'OD' mentioned below indicate approximate overall cable diameters. |
| 111 | Cable glands suitable for 650 / 1100 V (Uo / U) voltage grade, Al / Cu conductor (stranded / solid), XLPE insulated, screened, armoured power / control / lighting cables Cable Glands shall be of Nickel plated brass material, double compression type with PVC hood. |
| 112 | Cables with OD upto 20 mm. |
| 113 | Cables with OD above 20 mm but upto 30 mm. |
| 114 | Cables with OD above 30 mm but upto 40 mm. |
| 115 | Cables with OD above 40 mm but upto 50 mm |
| 116 | Cables with OD above 50 mm but upto 60 mm. |
| 117 | Cables with OD above 60 mm but upto 80 mm. |
| 118 | Cable glands suitable for 650 / 1100 V (Uo / U) voltage grade, Al / Cu conductor (stranded / solid), XLPE insulated, unarmoured power cables (for battery banks)Cable Glands shall be of Nickel plated brass with PVC hood / Nylon , single compression type . |
| 119 | Cables with OD upto 20 mm. |
| 120 | Cables with OD above 20 mm but upto 30 mm. |
| 121 | MV Cable glands for Explosive Atmospheres |
| 122 | Supply of cable glands MV cable glands for Explosive Atmospheres and all the associated accessories as per 'ANNEXURE-II to SCC - SCOPE OF SUPPLY - ELECTRICAL'.CONTRACTOR shall be responsible selection and supply of exactly suitable cable glands for the actual cables (technical particulars as per project technical specification) installed at site and equipment cable entry tread.'OD' mentioned below indicate approximate overall cable diameters. |
| 123 | Cable glands suitable for 650 / 1100 V (Uo / U) voltage grade, Al / Cu conductor (stranded / solid), XLPE insulated, screened, armoured power / control / lighting cables Cable Glands shall be of Nickel plated brass material, double compression type with PVC hood. |
| 124 | Cables with OD upto 20 mm. |
| 125 | Cables with OD above 20 mm but upto 30 mm. |
| 126 | Cables with OD above 30 mm but upto 40 mm. |
| 127 | Cables with OD above 40 mm but upto 50 mm |
| 128 | Cables with OD above 50 mm but upto 60 mm. |
| 129 | Cables with OD above 60 mm but upto 80 mm. |
| 130 | MV Cable gland reducers / expanders |
| 131 | Supply of MV Cable gland reducers / expanders and all the associated accessories as per 'ANNEXURE-II to SCC - SCOPE OF SUPPLY - ELECTRICAL'.CONTRACTOR shall be responsible selection and supply of exactly suitable reducers / expanders for the actual cables gland (technical particulars as per project technical specification) installed at site and equipment cable entry tread |
| 132 | MV Cable gland reducers - Industrial type |
| 133 | M20 x 1.5 (Male thread) to M16 x 1.5 (Female thread) |
| 134 | M25 x 1.5 (Male thread) to M20 x 1.5 (Female thread) |
| 135 | M32 x 1.5 (Male thread) to M25 x 1.5 (Female thread) |
| 136 | M50 x 1.5 (Male thread) to M32 x 1.5 (Female thread) |
| 137 | M63 x 1.5 (Male thread) to M50 x 1.5 (Female thread) |
| 138 | M80 x 1.5 (Male thread) to M63 x 1.5 (Female thread) |
| 139 | MV Cable gland expander Industrial type |
| 140 | M16 x 1.5 (Male thread) to M20 x 1.5 (Female thread) |
| 141 | M20 x 1.5 (Male thread) to M25 x 1.5 (Female thread) |
| 142 | M25 x 1.5 (Male thread) to M32 x 1.5 (Female thread) |
| 143 | M32 x 1.5 (Male thread) to M50 x 1.5 (Female thread) |
| 144 | M50 x 1.5 (Male thread) to M63 x 1.5 (Female thread) |
| 145 | M63 x 1.5 (Male thread) to M80 x 1.5 (Female thread) |
| 146 | MV Cable gland reducers for Explosive Atmospheres |
| 147 | M20 x 1.5 (Male thread) to M16 x 1.5 (Female thread) |
| 148 | M25 x 1.5 (Male thread) to M20 x 1.5 (Female thread) |
| 149 | M32 x 1.5 (Male thread) to M25 x 1.5 (Female thread) |
| 150 | M50 x 1.5 (Male thread) to M32 x 1.5 (Female thread) |
| 151 | M63 x 1.5 (Male thread) to M50 x 1.5 (Female thread) |
| 152 | M80 x 1.5 (Male thread) to M63 x 1.5 (Female thread) |
| 153 | LV Cable gland expander for Explosive Atmospheres |
| 154 | M16 x 1.5 (Male thread) to M20 x 1.5 (Female thread) |
| 155 | M20 x 1.5 (Male thread) to M25 x 1.5 (Female thread) |
| 156 | M25 x 1.5 (Male thread) to M32 x 1.5 (Female thread) |
| 157 | M32 x 1.5 (Male thread) to M50 x 1.5 (Female thread) |
| 158 | M50 x 1.5 (Male thread) to M63 x 1.5 (Female thread) |
| 159 | M63 x 1.5 (Male thread) to M80 x 1.5 (Female thread) |
| 160 | Cable entry blanking plugs |
| 161 | Supply of cable entry blanking plugs and all the associated accessories for sealing of unused cable entries, as per 'ANNEXURE-II to SCC - SCOPE OF SUPPLY - ELECTRICAL'.CONTRACTOR shall be responsible selection and supply of exactly suitable Cable entry blanking plugs as per equipment cable entry tread at site. |
| 162 | Cable entry blanking plugs Industrial type |
| 163 | Cable entry blanking plugs For Explosive Atmospheres |
| 164 | Cable Lugs:Supply of crimping type lugs for power / control / lighting / earthing cables of various sizes along with all the associated accessories including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.Supply of lugs are included in Termination cost, this item shall be operated only in case of re-termination/ re-lugging due to Owner/ Consultant's instructions. This item shall not be operated due to fault of Contractor. |
| 165 | Supply of crimping type TINNED COPPER LUGS lugs for power / control / lighting / earthing cables of various sizes.CONTRACTOR shall be responsible selection and supply of exactly suitable lug for the actual cable conductors for the cables (technical particulars as per project technical specification) installed at site and available termination arrangement. |
| 166 | All sizes upto 16 sq. mm. (Lugs shall be heavy duty and long barrel crimping type) |
| 167 | All sizes from 25 to 35 sq. mm. (Lugs shall be heavy duty and long barrel crimping type) |
| 168 | All sizes from 50 to 185 sq. mm. (Lugs shall be heavy duty and long barrel crimping type) |
| 169 | All sizes from 240 to 400 sq. mm. (Lugs shall be heavy duty and long barrel crimping type) |
| 170 | All sizes from 500 to 630 sq. mm. (Lugs shall be heavy duty and long barrel crimping type) |
| 171 | Supply of crimping type AL LUGS lugs for power / control / lighting / earthing cables of various sizes.CONTRACTOR shall be responsible selection and supply of exactly suitable lug for the actual cable conductors for the cables (technical particulars as per project technical specification) installed at site and available termination arrangement. |
| 172 | All sizes from 25 to 35 sq. mm. (Lugs shall be heavy duty and long barrel crimping type) |
| 173 | All sizes from 50 to 185 sq. mm. (Lugs shall be heavy duty and long barrel crimping type) |
| 174 | All sizes from 240 to 400 sq. mm. (Lugs shall be heavy duty and long barrel crimping type) |
| 175 | Supply of crimping type TINNED COPPER LUGS lugs for power / control / lighting / earthing cables of various sizes.CONTRACTOR shall be responsible selection and supply of exactly suitable lug for the actual cable conductors for the cables (technical particulars as per project technical specification) installed at site and available termination arrangement. |
| 176 | 1.5 sq. mm. (Lugs shall be insulated, Ring / Pin / Fork crimping type) |
| 177 | 2.5 sq. mm. (Lugs shall be insulated, Ring / Pin / Fork crimping type) |
| 178 | All sizes from 4 sq.mm. to 10 sq. mm. (Lugs shall be insulated,Ring / Pin / Fork crimping type) |
| 179 | Supply of crimping type lugs for below mentioned GI wire ropes of various sizes.CONTRACTOR shall be responsible selection and supply of exactly suitable lug for the actual cable conductors for the cables (technical particulars as per project technical specification) installed at site and available termination arrangement. |
| 180 | 10 mm dia. GI wire rope |
| 181 | 16 mm dia. GI wire rope |
| 182 | CABLE JOINTING |
| 183 | Cable straight through jointing kit |
| 184 | Supply of cable jointing kit along with all the associated accessories as per 'ANNEXURE-II to SCC - SCOPE OF SUPPLY - ELECTRICAL'. |
| 185 | HV Cable straight through jointing kit Heat shrinkable type (suitable for outdoor installation) for 6.6 / 6.6 kV (UE) voltage grade, Al conductor, XLPE insulated, screened, armoured power cable |
| 186 | 3C x 240 sq.mm A2XCEFY (UE) |
| 187 | HV Cable straight through jointing kit Heat shrinkable type (suitable for outdoor installation) for 33 / 33 kV (UE) voltage grade, Al conductor, XLPE insulated, screened, armoured power cable |
| 188 | 1C x 630 sq.mm A2XCEWaY (UE) |
| 189 | MV Cable straight through jointing kit (suitable for outdoor installation) for 650 / 1100 (Uo / U) voltage grade, Al / Cu conductor (stranded / solid), XLPE insulated, screened, armoured power / control / lighting cables |
| 190 | Cables with OD upto 20 mm. |
| 191 | Cables with OD above 20 mm but upto 30 mm. |
| 192 | Cables with OD above 30 mm but upto 40 mm. |
| 193 | Cables with OD above 40 mm but upto 50 mm. |
| 194 | Cables with OD above 50 mm but upto 60 mm. |
| 195 | Cables with OD above 60 mm but upto 80 mm. |
| 196 | PREFABRICATED CABLE TRAYS |
| 197 | Prefabricated Cable Trays (GI) and accessories |
| 198 | Supply of prefabricated GI perforated and ladder type cable tray / covers, tray separators along with all the associated consumable material for assembly and appropriate installation of the same, as per doc. no. TK-1P22A-EL-SPE-0024 (Technical Specification for GI cable Trays) |
| 199 | Cable Trays Perforated (GI) |
| 200 | 50 mm wide |
| 201 | 100 mm wide |
| 202 | 150 mm wide |
| 203 | Coupler plates along with SS304 fixing hardware |
| 204 | GI Coupler plates with 3 mm thick, along with necessary fixing hardware – stainless steel (SS304) nut, bolt, lock-nut) for 50/100/150 W perforated cable trays mentioned above. (Note : 1 no. set = 2 nos. coupler plates each) |
| 205 | GI Coupler plates with 2 mm thick, along with necessary fixing hardware – stainless steel (SS304) nut, bolt, lock-nut) for 50/100/150 W perforated cable trays mentioned above. (Note : 1 no. set = 2 nos. coupler plates each |
| 206 | Cable Ladders (GI) and Accessories |
| 207 | 150 mm wide |
| 208 | 300 mm wide |
| 209 | 600 mm wide |
| 210 | Prefabricated Bends and Accessories Cable Ladders (GI) |
| 211 | Pre-Fabricated 90 degree horizontal bends (Bending Radius 300mm) |
| 212 | 300 mm wide |
| 213 | 600 mm wide |
| 214 | Pre-Fabricated 90 degree horizontal bends (Bending Radius 600mm) |
| 215 | 300 mm wide |
| 216 | 600 mm wide |
| 217 | Pre-Fabricated 90 degree horizontal bends (Bending Radius 900mm) |
| 218 | 300 mm wide |
| 219 | 600 mm wide |
| 220 | Pre-Fabricated 90 degree horizontal bends (Bending Radius 1200mm) |
| 221 | 300 mm wide |
| 222 | 600 mm wide |
| 223 | Pre-Fabricated 90 degree Inside Vertical bends (Bending Radius 300mm) |
| 224 | 300 mm wide |
| 225 | 600 mm wide |
| 226 | Pre-Fabricated 90 degree Inside Vertical bends (Bending Radius 600mm) |
| 227 | 300 mm wide |
| 228 | 600 mm wide |
| 229 | Pre-Fabricated 90 degree Inside Vertical bends (Bending Radius 900mm) |
| 230 | 300 mm wide |
| 231 | 600 mm wide |
| 232 | Pre-Fabricated 90 degree Inside Vertical bends (Bending Radius 1200mm) |
| 233 | 300 mm wide |
| 234 | 600 mm wide |
| 235 | Pre-Fabricated 90 degree Outside Vertical bends (Bending Radius 300mm) |
| 236 | 300 mm wide |
| 237 | 600 mm wide |
| 238 | Pre-Fabricated 90 degree Outside Vertical bends (Bending Radius 600mm) |
| 239 | 300 mm wide |
| 240 | 600 mm wide |
| 241 | Pre-Fabricated 90 degree Outside Vertical bends (Bending Radius 900mm) |
| 242 | 300 mm wide |
| 243 | 600 mm wide |
| 244 | Pre-Fabricated 90 degree Outside Vertical bends (Bending Radius 1200mm) |
| 245 | 300 mm wide |
| 246 | 600 mm wide |
| 247 | Pre-Fabricated 45 degree horizontal bends (Bending Radius 300mm) |
| 248 | 300 mm wide |
| 249 | 600 mm wide |
| 250 | Pre-Fabricated 45 degree horizontal bends (Bending Radius 600mm) |
| 251 | 300 mm wide |
| 252 | 600 mm wide |
| 253 | Pre-Fabricated 45 degree horizontal bends (Bending Radius 900mm) |
| 254 | 300 mm wide |
| 255 | 600 mm wide |
| 256 | Pre-Fabricated 45 degree Inside Vertical bends (Bending Radius 300mm) |
| 257 | 300 mm wide |
| 258 | 600 mm wide |
| 259 | Pre-Fabricated 45 degree Inside Vertical bends (Bending Radius 600mm) |
| 260 | 300 mm wide |
| 261 | 600 mm wide |
| 262 | Pre-Fabricated 45 degree Inside Vertical bends (Bending Radius 900mm) |
| 263 | 300 mm wide |
| 264 | 600 mm wide |
| 265 | Pre-Fabricated 45 degree Outside Vertical bends (Bending Radius 300mm) |
| 266 | 300 mm wide |
| 267 | 600 mm wide |
| 268 | Pre-Fabricated 45 degree Outside Vertical bends (Bending Radius 600mm) |
| 269 | 300 mm wide |
| 270 | 600 mm wide |
| 271 | Pre-Fabricated 45 degree Outside Vertical bends (Bending Radius 900mm) |
| 272 | 300 mm wide |
| 273 | 600 mm wide |
| 274 | Pre Fabricated Cable Tray Reducer |
| 275 | 600 to 300 mm Reducer, Right Hand Side |
| 276 | 600 to 300 mm Reducer, Left Hand Side |
| 277 | 300 to 150 mm Reducer, Right Hand Side |
| 278 | 300 to 150 mm Reducer, Left Hand Side |
| 279 | Pre Fabricated Equal Tee’s (Bending Radius-300 mm) |
| 280 | 300 mm wide |
| 281 | 600 mm wide |
| 282 | Pre Fabricated Equal Tee’s (Bending Radius-600 mm) |
| 283 | 300 mm wide |
| 284 | 600 mm wide |
| 285 | Pre Fabricated Equal Tee’s (Bending Radius-900 mm) |
| 286 | 300 mm wide |
| 287 | 600 mm wide |
| 288 | Pre Fabricated Unequal Tee’s (Bending Radius-300 mm) |
| 289 | 300 x 150 x 300 mm wide |
| 290 | 600 x 150 x 600 mm wide |
| 291 | 600 x 300 x 600 mm wide |
| 292 | Pre Fabricated Unequal Tee’s (Bending Radius-600 mm) |
| 293 | 300 x 150 x 300 mm wide |
| 294 | 600 x 150 x 600 mm wide |
| 295 | 600 x 300 x 600 mm wide |
| 296 | Coupler plates along with SS304 fixing hardware |
| 297 | GI Coupler plates with 3 mm thick, 4 holes on both the sides of size M10 hole & M8 hardware (along with necessary fixing hardware – stainless steel nut, bolt, lock-nut) for 150/300/450/600 W ladder type cable trays mentioned above. (Note : 1 no. set = 4 nos. coupler plates each) |
| 298 | Stainless Steel Coupler plates with 2 mm thick, 4 holes on both the sides of size M10 hole & M8 hardware (along with necessary fixing hardware – stainless steel nut, bolt, lock-nut) for 150/300/450/600 W ladder type cable trays mentioned above. (Note : 1 no. set = 4 nos. coupler plates each) |
| 299 | Hinges along with SS304 fixing hardware |
| 300 | Hinged GI plates 3 mm thick, 80 mm height along with necessary fixing hardware – stainless steel (SS304) nut, bolt, lock-nut) suitable for tray size 300/450/600 mm W (Note : 1 no. set = 4 nos. coupler plates each) |
| 301 | Hinged GI plates 2 mm thick, 80 mm height along with necessary fixing hardware – stainless steel (SS304) nut, bolt, lock-nut) suitable for tray size 300/450/600 mm W (Note : 1 no. set = 4 nos. coupler plates each) |
| 302 | Tray Covers with fixing clamps along with necessary SS304 hardware |
| 303 | 100 mm wide |
| 304 | 150 mm wide |
| 305 | 300 mm wide |
| 306 | 600 mm wide |
| 307 | Hold Down Clamps (HDGI) |
| 308 | Hold down Clamps (HDGI) for Horizontal Ladder Cable Tray with necessary SS 304 fixing hardware |
| 309 | Hold down Clamps (HDGI) for Vertical Ladder Cable Tray with necessary SS 304 fixing hardware |
| 310 | Separators for Cable Ladders (GI) with necessart SS 304 fixing hardware |
| 311 | CONDUITS FOR CABLE LAYING / PROTECTION AND PULL BOXES |
| 312 | Supply of heavy duty rigid GI / PVC conduits and all the associated accessoriesSupply of accessories such as GI clamps, joints, bends reducers / adaptors for the conduits and other consumable material such as edge protection grommet at either ends for GI conduits as per the site requirement is considered in running meter length of the conduits. |
| 313 | Rigid GI conduits |
| 314 | 25 mm nominal dia |
| 315 | 50 mm nominal dia |
| 316 | 100 mm nominal dia |
| 317 | 150 mm nominal dia |
| 318 | Rigid GI conduits RED coloured (For Fire Alarm System cables) |
| 319 | 25 mm nominal dia |
| 320 | 50 mm nominal dia |
| 321 | Heavy duty PVC conduits |
| 322 | 25 mm nominal dia |
| 323 | 50 mm nominal dia |
| 324 | Flexible PVC conduits |
| 325 | 25 mm nominal dia |
| 326 | Pull boxes for cable pulling in conduits |
| 327 | Supply of pull boxes (GI enclosure) indicate below excludes pull boxes already covered in the section \\"Point Wiring for Office buildings / Control rooms / Other rooms with false ceiling\\" |
| 328 | 4 way Pull boxes,100mm L x 100mm W x 75mm D, 1no. 25mm knockout on all four sides |
| 329 | LIGHTING, SMALL POWER, WELDING SOCKETS AND JUNCTION BOXES |
| 330 | LIGHTING |
| 331 | Lighting fixtures |
| 332 | Supply of lighting fixtures and associated components / accessories such as lamps, chokes, condensers, reflectors for integral fixtures including certified glands, PVC hood and lugs, entry plugs etc. including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge. |
| 333 | Lighting Fixtures Industrial type Refer specification TK-1P22A-EL-SPE-0017 for LED type Industrial Light Fittings |
| 334 | 1x40W LED Tube Light Fixture |
| 335 | 2x20W LED Tube Light Fixture |
| 336 | 10W LED Bulkhead Light Fixture |
| 337 | 11W LED Decorative Down Light fixture suitable for false ceiling |
| 338 | 36W LED recessed mounted square (600 mm X 600 mm) fixture suitable for False Ceiling |
| 339 | 18W LED (suitable for 110V DC) recessed mounted square (600 mm X 600 mm) fixture suitable for False Ceiling |
| 340 | 1 X 45W LED, Well Glass Integral Luminaire |
| 341 | 1X26W,(suitable for 110V DC) LED Tube Light Fixture |
| 342 | Lighting Fixtures for Explosive AtmospheresRefer specification TK-1P22A-EL-SPE-0020 for LED type Light Fittings for Explosive Atmospheres. |
| 343 | 1 X 45W LED, Ex'd', IIC, T3 Well Glass Integral Luminaire |
| 344 | 1 X 26W (suitable for 110V DC) LED, Ex'd', IIC, T3 Well Glass Integral Luminaire |
| 345 | 1 X 100W LED, Ex'd', IIC, T3 Medium Bay / High Bay Integral Luminaire |
| 346 | 1 X 150W LED, Ex'd', IIC, T3 Medium Bay / High Bay Integral Luminaire |
| 347 | 1 X 250W LED, Ex'd', IIC, T3 Medium Bay / High Bay Integral Luminaire |
| 348 | 1 X 150W LED, Ex'd', IIC, T3 Flood Light Luminaire |
| 349 | LED aviation light Ex d, IIC, T3 (15W) with control panel. Colour of lamp and type (steady/ falshing) will be informed during Detailed Engineering. |
| 350 | 1X40W LED Tube light fixture , Ex'd', IIC, T3 |
| 351 | Special Lighting fixtures |
| 352 | Supply of special lighting fixtures and all the associated accessories, as per 'ANNEXURE-II to SCC - SCOPE OF SUPPLY - ELECTRICAL'. |
| 353 | Emergency lighting fixture with built-in battery |
| 354 | 1x18W, Fluorescent, Industrial |
| 355 | 1x18W, Fluorescent, for Explosive Atmospheres |
| 356 | Emergency EXIT sign with built-in battery |
| 357 | Refer 'ANNEXURE-II to SCC - SCOPE OF SUPPLY - ELECTRICAL' for the 'Type designations' (TYPE-1, TYPE-2 etc.) mentioned below. |
| 358 | TYPE-1 |
| 359 | TYPE-2 |
| 360 | Hand lamps |
| 361 | 24V Industrial Hand lamps along with 20 m extension cable 3C x 2.5sq.mm, YY, 20m, along with the plug suitable for 24V, 5A Industrial switch socket |
| 362 | 24V Hand lamps for Explosive Atmospheres (Zone1/Zone2, Ex-d, IIC, T3, ) alongwith 20 m extension cable 3c x 2.5sq.mm, YY long with the plug suitable for 24V, 5A Industrial switch socket |
| 363 | Supply of Lighting PolesSupply of GI lighting pole as per approved drawing along with supply of fixing hardware like U clamp & bolt, for platform mounted pole |
| 364 | Installation details : L04 |
| 365 | Installation details : L05 |
| 366 | Installation details : L11 |
| 367 | Installation details : L14A |
| 368 | EXHAUST FANS AND CEILING FANS |
| 369 | Industrial type Exhaust fans |
| 370 | Supply of Industrial type Exhaust fans and associated accessories such as louvers and bird screen, as per 'ANNEXURE-II to SCC - SCOPE OF SUPPLY - ELECTRICAL'. |
| 371 | 300mm dia. |
| 372 | 450mm dia. |
| 373 | 600mm dia. |
| 374 | Exhaust fans for Explosive Atmospheres |
| 375 | Supply of Exhaust fans for Explosive Atmospheres and associated accessories such as louvers and bird screen, as per 'ANNEXURE-II to SCC - SCOPE OF SUPPLY - ELECTRICAL'. |
| 376 | 300mm dia. |
| 377 | 450mm dia. |
| 378 | 600mm dia. |
| 379 | SMALL POWER |
| 380 | Supply of various small power equipment and all associated accessories, as per 'ANNEXURE-II to SCC - SCOPE OF SUPPLY - ELECTRICAL'. |
| 381 | Switch socket outlets |
| 382 | Supply of Decorative type switch socket outletsSupply of Supply of Decorative type switch socket outlets as per 'ANNEXURE-II to SCC - SCOPE OF SUPPLY - ELECTRICAL'. |
| 383 | Decorative type switch socket box with 1 no. 5/15A switch socket unit and 1 no. piano type switch |
| 384 | Decorative type switch socket box with 1 no. 5/15A switch socket unit and 2 nos. piano type switches |
| 385 | Decorative type switch socket box with 1 no. 5/15A switch socket unit and 3 nos. piano type switches |
| 386 | Decorative type switch socket box with 1 no. 5/15A switch socket unit and 4 nos. piano type switches |
| 387 | Decorative type switch socket box with 1 no. 5/15A switch socket unit and 5 nos. piano type switches |
| 388 | Decorative type switch socket box with 1 no. 5/15A switch socket unit |
| 389 | Decorative type switch in single module with 1 no. 5A piano type switches |
| 390 | Decorative type switch in double module with 2 no. 5A piano type switches |
| 391 | Decorative type switch in tripple module with 3 no. 5A piano type switches |
| 392 | Decorative type switch in quad module with 4 no. 5A piano type switches |
| 393 | Decorative type switch socket switchboard with 5/15A, 5 pin, socket outlet with 15A switch and 'ON' LED indication & fuse |
| 394 | Surface / Concealed mounting type ( 2-Module) RJ 11 / RJ 45 Connectors Female type complete with Moduler box, cover plate etc. for telephones |
| 395 | Industrial type switch socket outlets (for Indoor Installation) Supply of Industrial type switch socket outlets (for Indoor Installation) as per 'ANNEXURE-II to SCC - SCOPE OF SUPPLY - ELECTRICAL'. |
| 396 | 20A, single phase switch socket outlet with 1no. 3 pin socket and 1 No. 20 A, 10 kA, SPMCB, in sheet steel enclosure |
| 397 | Convenience Switch socket outlets Supply of Convenience Switch socket outlets as per 'ANNEXURE-II to SCC - SCOPE OF SUPPLY - ELECTRICAL'. |
| 398 | Industrial Convenience sockets (single phase) |
| 399 | 16A, 240 V 3 pin single phase socket outlet |
| 400 | Convenience sockets (single phase) for Explosive Atmospheres |
| 401 | 16A, 3 pin,240V AC single phase socket outlet (Ex-d , IIC , T3) |
| 402 | Industrial switch socket unit (portable) |
| 403 | 24V, 5A Industrial switch socket unit with built-in 100VA, 220V / 24V transformer |
| 404 | Switch socket unit for Explosive Atmospheres |
| 405 | 240V,16A and 24V, 5A combination type switch socket unit for Explosive Atmospheres (Zone 1/2, Ex-d , IIC , T3), with built-in 100VA, 240V / 24V transformer |
| 406 | 240V,16A and 24V, 5A combination type switch socket unit for Explosive Atmospheres (Zone 1/2, Ex-d , IIC , T3), with built-in 100VA, 240V / 24V transformer (Portable Handlamp Sockets supplied with trolleys) |
| 407 | JUNCTION BOXES (JB) / POWER JUNCTION BOXES (JB) |
| 408 | Supply of various types of junction boxes / power junction boxes suitable for the required cable entries and all associated accessories, as per doc. no.TK-1P22A-EL-SPE-0074 (Technical specification for Industrial Lighting & Small Power Panels, Junction Boxes & Welding Receptacles) and TK-1P22A-EL-SPE-0019 (Technical Specification for Flameproof Industrial Lighting & Small Power Panels, Junction Boxes & Welding Receptacles)Supply of junction boxes suitable for bottom entry of incoming and outgoing cables, inclusive of suitable terminals for undrilled gland plate, cable terminations, busbars for cable termination as required, facility for earthing cable termination inside and outside the termination, along with the associated accessories such plugs for cable openings, fixing hardware |
| 409 | Junction boxes Industrial type |
| 410 | Junction boxes (Indoor) |
| 411 | 4 way Lighting JB, Indoor |
| 412 | 5 way JB for small power sockets , Indoor |
| 413 | Junction boxes (Outdoor) |
| 414 | 4 way Lighting JB, Outdoor |
| 415 | 4 way Welding socket JB, Outdoor |
| 416 | Communication System Junction BoxesSupply of Industrial Weatherproof Junction boxes as per 'ANNEXURE-II to SCC - SCOPE OF SUPPLY - ELECTRICAL'.Supply of cable glands, cable blanking plugs suitable to cable OD, cable entry size is included in the scope |
| 417 | Indoor FA System JB For housing addressable module of 1 no. Exit LightIncoming : 2Px1.5 sq.mm(1 No.) - M25 + 1Px2.5 sq.mm(1 No.) - M20Outgoing : 2Px1.5 sq.mm(1 No.) - M25 + 1Px2.5 sq.mm(1 No.) - M20 |
| 418 | Indoor FA System JB Incoming : 2Px1.5 sq.mm(1 No.) - M25Outgoing : 2Px1.5 sq.mm(1 No.) - M25 |
| 419 | Indoor PA System JB for SpeakersIncoming : up to 20Px2.5 sq.mm(1 No.) - M40Outgoing : 2Px2.5 sq.mm(12 Nos.) - M25 (9 Nos. Gland + 3 Nos. Plug) |
| 420 | Outdoor PA System JB for SpeakersIncoming : up to 12Px2.5 sq.mm(1 No.) - M40Outgoing : 2Px2.5 sq.mm(12 Nos.) - M25 (9 Nos. Gland + 3 Nos. Plug) |
| 421 | Indoor PA System JB for FCSIncoming : up to 20Px2.5 sq.mm(1 No.) - M40Outgoing : 2Px2.5 sq.mm(12 Nos.) - M25 (9 Nos. Gland + 3 Nos. Plug) |
| 422 | Indoor Telephone System JB (IDF)Industrial Weatherproof type telephone system junction box /IDF Krone/screw type terminals, including termination and connections of incoming and outgoing telephone cableJB / IDF with 1 nos 20 Pair incoming cable(s) and 20 nos 2 Pair outgoing cable(s) |
| 423 | Junction boxes for Explosive Atmospheres |
| 424 | 4 way Lighting JB, (Ex-d, IIC , T3) |
| 425 | 5 way JB for small power sockets, (Ex-d, IIC , T3) |
| 426 | 4 way Welding socket JB, (Ex-d, IIC , T3) |
| 427 | Junction box (Ex-d, IIC , T3) suitable for 415 V system suitable for Incoming cable size 3R-3Cx240sq.mm and outgoing cable size 2R-3Cx240sq.mm |
| 428 | Junction boxes for Communication System Supply of Industrial Weatherproof Junction boxes as per 'ANNEXURE-II to SCC - SCOPE OF SUPPLY - ELECTRICAL'.Supply of cable glands, cable blanking plugs suitable to cable OD, cable entry size is included in the scope |
| 429 | Indoor FA System JB for housing addressable module of 1 no. DetectorIncoming : 2Px1.5 (1 No.)Outgoing : 2Px1.5 (1 No.), 1Px1.5 (1 Nos.)NPT thread glands : 3 Nos.Plugs : 2 Nos. (Plug for 2Px1.5 size) |
| 430 | Indoor FA System JB Incoming : 2Px1.5 (1 No.)Outgoing : 2Px1.5 (1 No.), 1Px1.5 (1 Nos.)NPT thread glands : 3 Nos.Plugs : 2 Nos. (Plug for 2Px1.5 size) |
| 431 | Outdoor FA System JB for housing addressable module of 1 no. MCPIncoming : 2Px1.5 (1 No.)Outgoing : 2Px1.5 (1 No.), 1Px1.5 (1 Nos.)NPT thread glands : 3 Nos.Plugs : 2 Nos. (Plug for 2Px1.5 size) |
| 432 | Outdoor FA System JB for housing addressable module of 1 no. Hooter / BeconIncoming : 2Px1.5 (1 No.)Outgoing : 2Px1.5 (1 No.), 1Px2.5 (1 Nos.)NPT thread glands : 3 Nos.Plugs : 2 Nos. (Plug for 2Px1.5 size) |
| 433 | Outdoor FA System JB for housing addressable module of 1 no. DetectorIncoming : 2Px1.5 (1 No.)Outgoing : 2Px1.5 (1 No.), 1Px1.5 (1 Nos.)NPT thread glands : 3 Nos.Plugs : 2 Nos. (Plug for 2Px1.5 size) |
| 434 | Outdoor FA System JB for Housing 2 addressable modules and 2 zener barrierIncoming : 2Px1.5 (1 No.)Outgoing : 2Px1.5 (1 No.), 1Px1.5 (2 Nos.)NPT thread glands : 4 Nos.Plugs : 2 Nos. (Plug for 2Px1.5 size) |
| 435 | Outdoor FA System JB for End of resistor / Fault Isolator in FA loopIncoming : 2Px1.5 (1 No.)Outgoing : 2Px1.5 (1 No.)NPT thread glands : 2 Nos.Plugs : 2 Nos. (Plug for 2Px1.5 size) |
| 436 | Indoor Telephone System JB (IDF)Flameproof type telephone system junction box /IDF 9Ex-d, IIC,T3) Krone/screw type terminals, including termination and connections of incoming and outgoing telephone cableJB / IDF with 1 nos 20 Pair incoming cable(s) and 20 nos 2 Pair outgoing cable(s) |
| 437 | Outdoor PA System JB for FCSIncoming : 12Px1.5 (1 No.)Outgoing : 2Px1.5 (6 Nos.) NPT thread glands : 7 Nos.Plugs : 2 Nos. (1 No. Plug for 12Px1.5 and 1 No. for 2Px1.5) |
| 438 | Outdoor PA System JB for SpeakersIncoming : 12Px2.5 (1 No.)Outgoing : 2Px2.5 (12 Nos.) NPT thread glands : 13 Nos.Plugs : 3 Nos. (1 No. Plug for 12Px2.5 and 2 Nos. for 2Px2.5) |
| 439 | Indoor PA System JB for SpeakersIncoming : 12Px2.5 (1 No.)Outgoing : 2Px2.5 (12 Nos.) NPT thread glands : 13 Nos.Plugs : 3 Nos. (1 No. Plug for 12Px2.5 and 2 Nos. for 2Px2.5) |
| 440 | POWER SOCKET OUTLETS |
| 441 | Supply of various types of power socket outlets and all associated accessories, as per doc. no.TK-1P22A-EL-SPE-0074 (Technical specification for Industrial Lighting & Small Power Panels, Junction Boxes & Welding Receptaclest) and TK-1P22A-EL-SPE-0019 (Technical Specification for Flameproof Lighting & Small Power Panels, Junction Boxes & Welding Receptacles) |
| 442 | Industrial Power Socket Outlets |
| 443 | Industrial type, 415V, 63A, TPN & E socket outlet, with die cast Al LM6 enclosure , Type WS1 |
| 444 | Industrial type, 415V, 100A, TPN & E socket outlet, with die cast Al LM6 enclosure , Type WS2 |
| 445 | Power Socket Outlets for Explosive Atmospheres |
| 446 | For Explosive Atmospheres, 415V, 63A, TPN & E socket outlet, with die cast Al LM6 enclosure, Type WS3 (Ex-d, IIC , T3) |
| 447 | EARTHING AND LIGHTNING PROTECTION |
| 448 | EARTHING MATERIAL |
| 449 | Earthing conductor |
| 450 | Supply of GI strip / bare copper conductor for earthing |
| 451 | 25 x 6 mm GI strip |
| 452 | 40 x 5 mm GI strip |
| 453 | 50 x 6 mm GI strip |
| 454 | 75 x 10 mm GI strip |
| 455 | Earth / lightning protection electrodes |
| 456 | Supply of Earth / lightning protection electrodes along with the associated accessories / material as per 'Installation Details - Earthing', including any additional hardware as per site requirement so as to ensure the completeness of installation work |
| 457 | Installation Type : E01A :100 mm Dia, 3 m length GI pipe earth electrode for Electrical Safety earth |
| 458 | Installation Type : E01B : 100 mm Dia, 6 m length GI pipe earth electrode for Instrument clean earth |
| 459 | Installation Type : E01A : 100 mm Dia, 3 m length GI pipe lightning protection electrode |
| 460 | Earth buses |
| 461 | Supply of Earth buses along with the associated accessories (excluding structural steel) as per 'Installation Details - Earthing' and applicable construction documents, including any additional material as per site requirement so as to ensure the completeness of installation work |
| 462 | Supply of steel support structure / supporting frames for above shall be considered separately in SECTION - F. |
| 463 | Installation Type : E02A GI earth bus for Electrical safety |
| 464 | Installation Type : E02B GI earth bus for Electrical safety |
| 465 | Installation Type : E02A - GI earth bus for instruments |
| 466 | Installation Type : E02B - GI earth bus for instruments |
| 467 | Installation Type : E20 - Mounted on cable tray for Electrical |
| 468 | Installation Type : E20 - Mounted on cable tray for Instrumentation |
| 469 | Installation Type : E22 - Cu insulated earth bus |
| 470 | Supply of following Earthing Materials as per Installation Type : E141. 9 DIA G.I. BAR2. SHARP JAW TONG TYPE HEAVY DUTY SPRING CLAMP-100A |
| 471 | LIGHTNING PROTECTION MATERIAL |
| 472 | Lightning protection conductor |
| 473 | Supply of GI strip / bare copper conductor/aluminium/HDGI Round conductor for Lightning protection and associated accessories |
| 474 | Supply of accessories such as test links, cross connectors, parallel connectors for lightning protection down conductors, epoxy insulator supports and the associated accessories as per 'Installation Details - Lightning Protection' / as indicated in applicable construction documents / as per the site requirement, are considered in running meter length of lightning protection down conductors. |
| 475 | Installation Type: E16 Roof Conductor (Conductor Size- 25x6mm) |
| 476 | Installation Type: E16 Down Conductor (Conductor Size- 25x6mm) |
| 477 | Test Link : E16 : 50x6mm GI Link 150mm Long |
| 478 | Lightning protection rods / finials |
| 479 | Supply of Lightning protection rods / finials (lightning arrestors) along with the associated accessories (excluding structural steel) as per 'Installation Details - Lightning Protection' and applicable construction documents, including any additional material as per site requirement so as to ensure the completeness of installation work |
| 480 | Supply of steel support structure / supporting frames for above shall be considered separately in SECTION - F. |
| 481 | Installation Type : E24 |
| 482 | Installation Type : E25 |
| 483 | Installation Type : E26 |
| 484 | Installation Type : E27 |
| 485 | STRUCTURAL STEEL |
| 486 | Supply of structural steelSection wise requirement shall be estimated by CONTRACTOR, as per the applicable construction documents / various applicable 'Installation Details' mentioned in 'SECTIONS - A to E' in this document.Measurement of steel quantity for installation shall be based on actual quantities installed at site without wastage allowance. |
| 487 | Structural steel (MS) |
| 488 | Supply of coating material and paint as required for surface preparation and painting of steel shall be as per doc. TP-1ZZZA-PI-SPE-0003 (Technical Specification for Painting) is included in scope. |
| 489 | Structural steel (Hot deep galvanized GI) |
| 490 | MISCELLANEOUS ITEMS |
| 491 | CANOPIES |
| 492 | Supply of GI / FRP canopies for various equipment and all associated accessories, as per 'ANNEXURE-II to SCC - SCOPE OF SUPPLY - ELECTRICAL'.Site visit as required to confirm the actual dimensions / arrangement of various equipment installed at site, so as to fabricate canopy exactly suitable for the equipment is considered in the scope.Supply of all the Installation Material (including steel supporting frame as required) required as per site requirement is included in the scope. |
| 493 | Canopies for Motors |
| 494 | GI canopy complete with louvers backed up by wire mesh |
| 495 | Upto 3.0 kW |
| 496 | 3.7 kW to 15 kW |
| 497 | 18.5 kW to 37.0 kW |
| 498 | 45.0 kW to 90 kW |
| 499 | 110 kW to160 kW |
| 500 | GI canopy complete with louvers backed up by wire mesh - HV (6.6kV) Motors |
| 501 | Above kW to 280 kW |
| 502 | Above 280 kW to 500 kW |
| 503 | Above 500 kW to 750 kW |
| 504 | Above 750 kW to 1200 kW |
| 505 | Above 1200 kW to 2000 kW |
| 506 | Above 2000 kW to 5000 kW |
| 507 | Above 5000 kW to 8000 kW |
| 508 | GI Canopies omplete with louvers backed up by wire mesh for MV panels (wall / concrete / steel structure mounted) / LCS / Power Socket Outlets /Convenience Socket Outlets |
| 509 | LDB / ELDB / PDBs |
| 510 | Local Control Station (LCS) |
| 511 | 20A / 32A Power Socket Outlets in sheet steel enclosure / die cast Al LM6 body |
| 512 | 63A / 100A Power Socket Outlets in sheet steel enclosure / die cast Al LM6 body |
| 513 | CIVIL WORK |
| 514 | Anchor fasteners |
| 515 | Supply of aheavy duty Galvanised steel anchor fasteners for supporting various equipment in brick work / concrete work |
| 516 | Supply of anchor fasteners indicated below excludes those already considered in various 'Installation Details' mentioned in 'SECTIONS - A to E' in this document. |
| 517 | Anchor fasteners M8 type x 60mm |
| 518 | Anchor fasteners M10 type x 75 mm |
| 519 | Anchor fasteners M12 type x 100 mm |
| 520 | Supply of certified soft sand of known resistivity (Resistivity of sand shall be between 10,000 – 30,000 ohm.cm. ) |
| 521 | Supply of approved second class bricks of 75 mm thickness in cable trenches for cable protection, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge. |
| 522 | Supply approved Red coloured concrete tiles in cable trenches for cable protectionas per approved drawings, specifications of this tender and directions of Engineer-in-Charge. |
| 523 | SAFETY ITEMS |
| 524 | Supply of safety items as per applicable statutory requirements / HSE documents / as indicated in applicable construction documents |
| 525 | Enameled caution boards for 33 kV. |
| 526 | Enameled caution boards for 6.6 kV. |
| 527 | Enameled caution boards for 1.1 kV. |
| 528 | Enameled Danger plates to be installed in electrical rooms such as transformer bay, switchgear room etc. |
| 529 | 3 ply Lamicoid tag plates of appropriate size for various equipment, with White letters on Black background, as per the site requirement |
| 530 | Epoxy insulating floor coating (Valency Compound Make - Valency-111 CLASS A or equivalent |
| 531 | 33kV System |
| 532 | 6.6 kV systems - |
| 533 | upto 1.1 kV systems |
| 534 | Supply of 1000mm wide Synthetic Insulating mat (as per IS 15652: 2006) including supply of necessary adhesive for following grades (thickness as per voltage withstand requirements) required for maintenance of electrical equipment in substation, including cutting to required shape in running length, including all labour and materials, as per applicable Indian or International standards and CEA Guidelines and as per directions of Engineer-in-Charge |
| 535 | 33kV System |
| 536 | 6.6 kV systems - |
| 537 | upto 1.1 kV systems |
| 538 | First aid information chart (for electrical hazards such as Shock treatment): Framed laminated shock treatment chart, conforming to IE rules, in English and local language \\"Assamese\\". Name, address and telephone number of nearest doctor shall be mentioned in it. |
| 539 | First aid boxes along with required medicines / medical equipment, containing ointments for treatment of electrical burns, conforming to IE rules. |
| 540 | Wall mounted, Electrical Single Line Diagrams-A0 size\\" for the unit including frame, glass, hardwares, etc. |
| 541 | Industrial electrical Rubber hand gloves, Class 1 of reputed make |
| 542 | Rubber hand gloves pairs (1.1 kV grade). |
| 543 | Rubber hand gloves pairs (6.6 grade). |
| 544 | Rubber hand gloves pairs (33 kVgrade). |
| 545 | Discharge rod with earthing facility (upto 6.6 kV grade) with voltage detection |
| 546 | Discharge rod with earthing facility (Above6.6 kV up to 33kV) with voltage detection |
| 547 | LOTO with multiple locks (HESP) of reputed make. |
| 548 | Locks with keys of reputed make |
| 549 | Supply of following items for Battery area |
| 550 | Chemical Resistant Apron |
| 551 | Chemical Resistant Boot Pairs |
| 552 | Chemical Resistant Hand Gloves Pairs |
| 553 | Goggles used for Chemical handling |
| 554 | Electrical Protection suit / ARC FLASH SUIT 12CAL with JACKET, PANT ,GLOVES and FACE SHIELD for 12 Calories |
| 555 | GENERAL ITEMS |
| 556 | Supply of following items and all the associated accessories as per 'ANNEXURE-II to SCC - SCOPE OF SUPPLY - ELECTRICAL'. |
| 557 | Office tables of reputed make |
| 558 | Office chairs of reputed make |
| 559 | Full size Cupboard of reputed make, sheet steel enclosure (for documentation) |
| 560 | Tool Cabinet, Wall Mounted |
| 561 | Key Cabinet, Wall Mounted |
| 562 | Tarpaulin (for weather protection of stored electrical equipment) |
| 563 | Insulated step ladder of reputed make (suitable for indoor work in switchgear rooms) |
| 564 | Supply of Fire proofing of cables up 3 m length at entry points of both endsincluding all labour and materials required. (Actual area of surface painted shall be measured) _ - (As perIEC 60331) Fire proof paint for cables for 1 hour Fire Rating (CABLE SURFACE AREA WISE)Fire retardant cable coatingHILTI : CP679A / OBO BETTERMAN equivalent product |
| 565 | Supply of Fire Stop (Fire Sealing) material suitable to withstand for 240 mins including all labour and materials required for sealing the wall opening / conduits fire sealings.Refer annex EW4-6 for details of openings to be sealed |
| 566 | Supply of Fire Stop (Fire Sealing) material suitable to withstand for 90 mins including all labour and materials required for sealing the wall opening / conduits fire sealings.Refer annex EW4-6 for details of openings to be sealed |
| 567 | Supply of Weather proofing material HILTI make including all labour and materials required for sealing the wall opening / conduits fire sealings. |
| 568 | LV Switchgear Components |
| 569 | 6A, 9 kA, DP MCB |
| 570 | 10A, 9 kA, DP MCB |
| 571 | 20 / 32 A, 9 kA, DP MCB |
| 572 | Terminal Blocks |
| 573 | up to 2.5 sqmm |
| 574 | Above 2.5 sq. mm up to 6 sqmm |
| 575 | Ethernet Switch |
| 576 | Unmanaged Ethernet switch - Dual Power Supply (110V DC / 230 V AC)No of Ports : 6 X RJ 45 Ethernet Ports + 2 XFO Ports (Multi Mode)Uplink Speed : 1000MBPS /1GBPS The scope includes supply of LIU / Patch Panel with MMFO Patch cords (Length : 5 meter)between Ethernet switch & LIU. |
| 577 | Unmanaged Ethernet switch - Dual Power Supply (110V DC / 230 V AC)No of Ports : 10 X RJ 45 Ethernet Ports + 2 XFO Ports (Multi Mode)Uplink Speed : 1000MBPS /1GBPS The scope includes supply of LIU / Patch Panel with MMFO Patch cords (Length : 5 meter)between Ethernet switch & LIU. |
| 578 | TOOLS & TACKLES OF REPUTED MAKEMake shall be approved by Owner / Consultant, all supplied material shall be industrial grade, ISI certified. |
| 579 | True RMS Digital Multimeter with Display of up to 3 digits of decimal.Make:-Megger,Fluke, Kyoritsu, Hyoki |
| 580 | Continuity Testers |
| 581 | Tong Testers Make:-Meco, Megger, Fluke, Kyoritsu, Hyoki |
| 582 | Phase Sequence Meter |
| 583 | Tachometers (Non-Contact type) |
| 584 | Lux Level Meters for illumination check |
| 585 | Insulation Resistance Testers (Meggers) of 500V, 1000V ratingMake:-Megger,Fluke,kyoritsu, Hyoki |
| 586 | Insulation Resistance Testers (Meggers) of 2500V & 5000V rating, battery operated-Make:-Megger,Fluke,kyoritsu, Hyoki |
| 587 | Earth Resistance Testers with all accessories and clamps -Make: -Megger,Fluke,kyoritsu, Hyoki |
| 588 | GENERAL NOTESThis document shall be read in conjunction with doc. \\"SCOPE OF WORK-ELECTRICAL\\" DOC ID TK-1P22A-EL-SPE-0022.For 'Limit of Variation' in the rates / quantities / total value of work, please refer 'SPECIAL CONDITIONS OF CONTRACT'.CONTRACTOR shall only use 'Released for Construction (RFC)' drawings / documents for execution of work during the Construction phase.Dismantling activities shall be paid at 30% of the unit rates of the respective installation work. Dismantling activities shall only be paid to CONTRACTOR if instructed by OWNER / CONSULTANT, and not for erroneous execution done by CONTRACTOR.All the fixing hardwares such as nuts, bolts, U-bolts, screws, washers & clamps shall be of Stainless Steel (SS304), unless otherwise specified in Installation details and applicable construction documentsCONTRACTOR shall ensure that the rates quoted for execution of electrical works take into account all requirements, services, activities & responsibilities defined as forming part of CONTRACTOR’s scope in the Tender Document / Contract.Special attention shall be given to include the efforts necessary to implement & comply with the relevant safety practices to be followed for the electrical works at the Plant Site, as per the applicable HSE documents.CONTRACTOR should read entire specification to understand in totality the scope of supply and Installation. Every line item for Supplies and Installation should be read along with the respective Installation standard / hook up drawings related to that specific line item to understand the scope of supply and Installation in totality. Any missouts in supply scope in this regard by the CONTRACTOR shall not be entertained. |
| 589 | EQUIPMENT |
| 590 | TRANSFORMERS |
| 591 | Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, installation of assemblies / sub-assemblies, assembling and installation of components / devices supplied separately/ loose - as recommended by MANUFACTURER / applicable construction documents, Testing of oil, first filling and first filtration of oil, touch up painting, stenciling with paint on equipment enclosures as required and other associated work so as to ensure the completeness of installation work.Testing and precommissioning activities, commissioning assistance as required by MANUFACTURER's supervisor is included in the scope.Minor civil work such as chipping, grouting for fixing of associated equipment / assemblies and replastering the same as per the site requirement (including the supply of consumable material for the same) is included in the scope. Supply of all fixing hardware as per the site requirement is included in the scope.Supply, Fabrication, surface preparation, painting and installation of steel support of steel support structure / supporting frames as per the site requirement for above shall be considered separately in SECTION - F |
| 592 | Power transformers (Oil filled) |
| 593 | TAG : 1U64-SS16-TR-210A & 1U64-SS16-TR-210BRating : 25 / 31.5 MVA, 33 kV / 6.9 kV, ONAN / ONAF, Dyn11 WITH OCTC, 2 winding including PDMS, OMR SystemApprox. Dimensions (LxBxH) : 5730 x 3940 x 4330 mmOil capacity : 7700 ltrs. (6380kg.)Approx. Weight : 36180 kg (including oil)The Transformer Tank may be partially filled with oil at the time of shipment. CONTRACTOR shall completely fill the Tank at site. |
| 594 | Distribution transformers (Oil filled) |
| 595 | TAG : 1U64-SS16-TR-331A/B, 332A/B, 333A/B, 334A/BRating : 2000 kVA, 6.6 kV / 433 V, ONAN, Dyn11 WITH OCTCApprox. Dimensions (LxBxH) : 3300 x 2400 x 3500mmOil capacity : 1850 ltrs.Approx. Weight : 7900 kg (including oil)The Transformer Tank may be partially filled with oil at the time of shipment. CONTRACTOR shall completely fill the Tank at site. |
| 596 | Dry type transformers (Lighting / Heat tracing / Isolation transformers etc.) with all accessories |
| 597 | TAG : 1U64-SS16-TR-335Rating : 2200 kVA, 6600 V / 433 V, 2 winding, indoor installationApprox. Dimensions (LxBxH) : 3700 X 3100 X 3200 mmApprox. Weight : 6200 Kg Location : Indoor |
| 598 | TAG : 1U64-SS16-TR-503A/BRating : 300 kVA, 415 V / 433 V, 2 windingApprox. Dimensions (LxBxH) : 1620 X 1675 X 1550 mmApprox. Weight : 1400 KgLocation : Indoor |
| 599 | TAG : 1U64-SS16-TR-504A/B Rating : 50 kVA, 415 V / 433 V, 2 windingApprox. Dimensions (LxBxH) : 1680X 1000 X 1000 mmApprox. Weight : 460 kgLocation : Indoor |
| 600 | Filtration of transformer oil by filter machine provided by the contractor for improving the insulation strength of oil to the required strength, including all labour and materials, specifications of this tender and directions of Site Engineer-in-Charge. (Excluding the supply of oil). but including required BDV oil testingCost of first filteration shall be included in installation cost of Transformer. This rate shall be applicable only in event of addtional filteration requirement due to site conditions after completion of first flteration |
| 601 | BUSDUCTS |
| 602 | Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of shipping sections / assemblies / sub-assemblies, assembling and installation of components including bends and risers / devices supplied separately - as recommended by MANUFACTURER / applicable construction documents, alignment for appropriate termination of busbars at both the ends, Installation of bends, fixing of flexible joints, stenciling with paint on equipment enclosures as required and other associated work so as to ensure the completeness of installation workTesting, precommissioning and commissioning activities are included in the scopeMinor civil work such as chipping and modifications in the wall cutout, as required, for making busduct wall opening suitable for busduct entry etc., replastering and making area good as per the site requirement (including the supply of consumable material for the same), sealing with fire proofing compound, is included in the scope. Supply of all fixing hardware as per the site requirement is included in the scope.Fabrication and installation of steel support structure / supporting frames (inside and outside the substation building) for equipment as per the site requirement, is considered separately in SECTION - F. |
| 603 | 6.6 kV, 3150 A, 40kA for 1 sec, Aluminium busbar Construction : Sheet steel / Aluminium enclosure, Phase SegregatedFrom : Transformer secondary to Switchgear IncomersApprox. Weight : 340 kg / m |
| 604 | 415 V, 3200 A, 50kA for 1 sec, Aluminium busbarConstruction : Sandwich type, Material of enclosure : Galvanized steel / AluminiumFrom : Transformer secondary to Switchgear Incomer Approx. Weight : 50 kg / m |
| 605 | NEUTRAL GROUNDING RESISTOR (NGR) |
| 606 | Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of equipment and accessories, assembling and installation of components / devices supplied separately - as recommended by MANUFACTURER / applicable construction documents, stenciling with paint on equipment enclosures as required and other associated work so as to ensure the completeness of installation work.Testing, precommissioning and commissioning activities are included in the scope.Minor civil work such as chipping, grouting for fixing of equipment / assemblies and replastering the same as per the site requirement (including the supply of consumable material for the same) is included in the scope. Supply of all fixing hardware as per the site requirement is included in the scope.Fabrication and installation of steel support structure / supporting frames for equipment as per the site requirement, is considered separately in SECTION - F. |
| 607 | TAG : 1U64-SS16-NGR-210A/BRating : 3.8 kV, 400 A for 30 secApprox. Dimensions (LxBxH) : 1450 x 890 x 950 mmApprox. Weight : 450 kgs |
| 608 | HV SWITCHBOARDS - 6.6kV Switchboards, HV PFIC Panels, HV VFD / Soft Starter panels etcHandling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of various shipping sections / assemblies, assembling and installation of components / devices supplied separately - as recommended by MANUFACTURER / applicable construction documents, interpanel wiring, stenciling with paint on equipment enclosures as required, and other associated work so as to ensure the completeness of installation work.Installation of condition monitoring sensors, modules etc. as applicable is included in the scope.Testing and precommissioning activities, commissioning assistance as required by MANUFACTURER's supervisor is included in the scope. Minor civil work such as chipping, grouting for fixing of equipment as per the site requirement and replastering the same (including the supply of consumable material for the same) is included in the scope. Fabrication and installation of steel support structure / supporting frames for equipment as per the site requirement, is considered separately in SECTION - F.Supply of all fixing hardware as per the site requirement is included in the scope. |
| 609 | TAG : 1U64-SS16-AIS-210Rating : 6.6 kV, 3150 A, 40kA for 1 sec.Construction : Floor mounting, single frontNos. of vertical sections : 72Approx. Dimensions (LxBxH)mm : 600/800/1000 x 1950/2250/2500 x 2500 mm (per vertical section)Approx. Weight : 800 / 1200 kg (per vertical section) Switchboard Arrangement : Double Line,front to front The scope includes installation of interconnecting busduct between 2 lines of switchboard & Arc duct / arc absorber with wall frame assembly as applicable. |
| 610 | Unit rate for additional / deletion of Vertical section for Item as per sr. no. A/4.1 |
| 611 | TAG : 1U64-KAM-2781-VCB (6.6 kV Output VCB Panel)Rating : 6.6 kV, 800 A, 40kA for 1 sec.Nos. of vertical sections : 3Approx. Dimensions (LxBxH)mm : 600 x 1570/1970 x 2500mm (per vertical section)Approx. Weight : 700 kg (per vertical section) |
| 612 | TAG : 1U64-KAM-2782A/B-VCB (6.6 kV Output VCB Panel)Rating : 6.6 kV, 1250 A, 40kA for 1 sec.Nos. of vertical sections : 2Approx. Dimensions (LxBxH)mm : 600 x 1570 x 2200mm (per vertical section)Approx. Weight : 700 kg (per vertical section) |
| 613 | TAG : 1U64-SS16-CAP-210A/B (PFIC Panel, indoor type)Rating : 6.6 kV, 3750 kVAr Nos. of vertical sections : 6Approx. Dimensions (LxBxH)mm : 1200/1400 x 2400 x 2475 mm (per vertical section)Approx. Dimensions (LxBxH)mm : 9400 x 2400 x 2475 mm (overall)Approx. Weight : 1800 kg (per vertical section) |
| 614 | TAG : 1P23-KAM-2781-VFD1 and 1P23-KAM-2781-VFD1 (HV VFD Panel)Rating : 6.6 kV, 2600 kW Approx. Dimensions (LxBxH) : 6000 x 1500/1200 x 2800 mm Approx. Weight : 8800 kgs Mounting : On floorScope also includes installation of -common PLC Panel with approx. dimensions (L X B XH) : 2000 mm X 600 mm X 2315 mm, Approx. weight : 600 kgsCommon CMS Panel with approx. dimensions (L X B XH) : 700 mm X 350 mm X 700 mm, Approx. weight : 70 kgs |
| 615 | TAG : 1P23-KAM-2782A/B-VFD (Soft Starter Panel)Rating : 6.6 kV, 2600 kW Approx. Dimensions (LxBxH) : 6300 x 1100 x 2750 mm Approx. Weight : 9900 kgs Mounting : On floorApprox. weight : 9900 kgs |
| 616 | LV / MV SWITCHBOARDS (FLOOR MOUNTED) |
| 617 | Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of various shipping sections / assemblies, assembling and installation of components / devices supplied separately - as recommended by MANUFACTURER / applicable construction documents, interpanel wiring, stenciling with paint on equipment enclosures as required, and other associated work so as to ensure the completeness of installation work.Installation of condition monitoring sensors, modules etc. as applicable is included in the scope.Testing and precommissioning activities, commissioning assistance as required by MANUFACTURER's supervisor is included in the scope.Minor civil work such as chipping, grouting for fixing of equipment as per the site requirement and replastering the same (including the supply of consumable material for the same) is included in the scope.Fabrication and installation of steel support structure / supporting frames for equipment as per the site requirement, is considered separately in SECTION - F. Supply of all fixing hardware as per the site requirement is included in the scope. |
| 618 | TAG : 1U64-SS16-PMCC-331Rating : 415 V, 3200 A, 50 kA for 1 sec.Construction : Floor mounting, single frontNos. of Shipping sections : ~ 10Approx. Maximum Dimensions (LxBxH)mm : 1900 x 1750 x 2630mm (per shipping section)Approx. Dimensions (LxBxH)mm : 15000 x 950 / 1450 / 1750 x 2630 mm (overall)Approx. Maximum Weight : 2100 KGS.(per shipping section ) Approx. Weight : 16000 KGS.(overall ) |
| 619 | TAG : 1U64-SS16-PMCC-332Rating : 415 V, 3200 A, 50 kA for 1 sec.Construction : Floor mounting, single frontNos. of Shipping sections : ~ 10Approx. Maximum Dimensions (LxBxH)mm : 1650 x 1750 x 2630mm (per shipping section)Approx. Dimensions (LxBxH)mm : 14000 x 950 / 1450 / 1750 x 2630 mm (overall)Approx. Maximum Weight : 1900 KGS.(per shipping section ) Approx. Weight : 14500 KGS.(overall ) |
| 620 | TAG : 1U64-SS16-PMCC-333Rating : 415 V, 3200 A, 50 kA for 1 sec.Construction : Floor mounting, single frontNos. of Shipping sections : ~ 9Approx. Maximum Dimensions (LxBxH)mm : 1900 x 1750 x 2630mm (per shipping section)Approx. Dimensions (LxBxH)mm : 14500 x 950 / 1450 / 1750 x 2630 mm (overall)Approx. Maximum Weight : 2100 KGS.(per shipping section ) Approx. Weight : 17000 KGS.(overall ) |
| 621 | TAG : 1U64-SS16-EPMCC-334Rating : 415 V, 3200 A, 50 kA for 1 sec.Construction : Floor mounting, single frontNos. of Shipping sections : ~ 13Approx. Maximum Dimensions (LxBxH)mm : 1650 x 1750 x 2630mm (per shipping section)Approx. Dimensions (LxBxH)mm : 19500 x 950 / 1450 / 1750 x 2630 mm (overall)Approx. Maximum Weight : 2100 KGS.(per shipping section ) Approx. Weight : 21500 KGS.(overall ) |
| 622 | TAG : 1U64-SS16-MCC-446Rating : 415 V, 800 A, 50 kA for 1 sec.Construction : Floor mounting, double frontNos. of Shipping sections : ~ 4Approx. Maximum Dimensions (LxBxH)mm : 2450 x 1250 x 2600mm (per shipping section)Approx. Dimensions (LxBxH)mm : 7250 x 950 / 1250 x 2600 mm (overall)Approx. Maximum Weight : 2100 KGS.(per shipping section ) Approx. Weight : 6500 KGS.(overall ) |
| 623 | TAG : 1U64-SS16-MCC-447Rating : 415 V, 800 A, 50 kA for 1 sec.Construction : Floor mounting, double frontNos. of Shipping sections : ~ 7Approx. Maximum Dimensions (LxBxH)mm : 2450 x 1250 x 2600mm (per shipping section)Approx. Dimensions (LxBxH)mm : 11100 x 950 / 1250 x 2600 mm (overall)Approx. Maximum Weight : 2100 KGS.(per shipping section ) Approx. Weight : 10000 KGS.(overall ) |
| 624 | TAG : 1U64-SS16-MCC-448Rating : 415 V, 800 A, 50 kA for 1 sec.Construction : Floor mounting, double frontNos. of Shipping sections : ~ 12Approx. Maximum Dimensions (LxBxH)mm : 2450 x 1250 x 2600mm (per shipping section)Approx. Dimensions (LxBxH)mm : 22000 x 950 / 1250 x 2600 mm (overall)Approx. Maximum Weight : 2100 KGS.(per shipping section ) Approx. Weight : 19000 KGS.(overall ) |
| 625 | TAG : 1U64-SS16-MCC-450Rating : 415 V, 800 A, 50 kA for 1 sec.Construction : Floor mounting, double frontNos. of Shipping sections : ~ 4Approx. Maximum Dimensions (LxBxH)mm : 2450 x 1250 x 2600mm (per shipping section)Approx. Dimensions (LxBxH)mm : 8000 x 950 / 1250 x 2600 mm (overall)Approx. Maximum Weight : 2100 KGS.(per shipping section ) Approx. Weight : 7200 KGS.(overall ) |
| 626 | TAG : 1U64-SS16-MCC-451Rating : 415 V, 800 A, 50 kA for 1 sec.Construction : Floor mounting, double frontNos. of Shipping sections : ~ 5Approx. Maximum Dimensions (LxBxH)mm : 2450 x 1250 x 2600mm (per shipping section)Approx. Dimensions (LxBxH)mm : 8000 x 950 / 1250 x 2600 mm (overall)Approx. Maximum Weight : 2100 KGS.(per shipping section ) Approx. Weight : 7200 KGS.(overall ) |
| 627 | TAG : 1U64-SS16-EMCC-452Rating : 415 V, 800 A, 50 kA for 1 sec.Construction : Floor mounting, double frontNos. of Shipping sections : ~ 7Approx. Maximum Dimensions (LxBxH)mm : 2450 x 1250 x 2600mm (per shipping section)Approx. Dimensions (LxBxH)mm : 9500 x 950 / 1250 x 2600 mm (overall)Approx. Maximum Weight : 2100 KGS.(per shipping section ) Approx. Weight : 8500 KGS.(overall ) |
| 628 | TAG : 1U64-SS16-ASB-504Rating : 415 V, 800 A, 50 kA for 1 sec.Construction : Floor mounting, double frontNos. of vertical sections : ~12Approx. Dimensions (LxBxH)mm : 800/1050 x 1750/1450 x 2530 mm (per vertical section) Approx. Weight : 900 KGS.(per vertical section ) |
| 629 | TAG : 1U64-SS16-MLDB-503Rating : 415 V, 800 A, 20 kA for 1 sec.Construction : Floor mounting, single frontNos. of vertical sections : ~12Approx. Dimensions (LxBxH)mm : 800/1050 x 1450/650 x 2430 mm (per vertical section) Approx. Weight : 900 KGS.(per vertical section ) |
| 630 | TAG : 1U64-SS16-EMLDB-504Rating : 415 V, 100 A, 10 kA for 1 sec.Construction : Floor mounting, single frontApprox. Overall Dimensions (LxBxH)mm : 6000 x 650 x 2430 mm Approx. Weight : 500 kg |
| 631 | MISCELLANEOUS Panels / Items(WALL / CONCRETE / STEEL STRUCTURE MOUNTED)(Industrial / For Explosive Atmospheres) |
| 632 | Installation of industrial weather proof / flame proof Lighting, Power panels on steel structures/concrete coloumn/wall etc, including supply & making of concrete foundations if required for supports, minor civil works if any, and installation of canopies. This also includes supply of necessary hardware, cement, sand , touch up painting, stenciling , Including Lifting & Transportation from storage area to the place of installation with contractor's own lifting and transportation arrangement, unpacking, assembly, including all labour and materials complete as per approved drawings,Installation of LV panels (wall / concrete / steel structure mounted) shall be as per 'Installation Details - Power' and applicable construction documentsSupply of Installation materials (excluding structure steel), including any additional material as per site requirement so as to ensure the completeness of installation work is included in the scopeTesting, precommissioning and commissioning activities are included in the scope.Minor civil work such as chipping, grouting for fixing of equipment and replastering the same as per the site requirement (including the supply of consumable material for the same) is included in the scope.Fabrication and installation of steel support structure / supporting frames for equipment as per the site requirement, is considered separately in SECTION - F. Supply of all fixing hardware as per the site requirement is included in the scope.Weights indicated below are euqipment/ item weights to be installed. |
| 633 | Lighting / Power PanelsLDB / ELDB / DL LDB / PDB (6way / 9way / 12way / 15way / 18way/ 24 Way) |
| 634 | Local Control Panel / Local Starter Panel / Local Isolators / Hydro jetting PDB |
| 635 | Weight of the Unit up to 20 kg |
| 636 | Weight of the Unit above 20 up to 100 kg |
| 637 | Weight of the Unit above 100 upto 200 kg. |
| 638 | Weight of the Unit above 200 upto 300 kg. |
| 639 | BATTERY CHARGER (DC UPS) AND BATTERY |
| 640 | Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of equipment / assemblies, assembling and installation of components / devices supplied separately - as recommended by MANUFACTURER / applicable construction documents, stenciling with paint on equipment enclosures as required and other associated work so as to ensure the completeness of installation work.Assembly of battery rack, placement of battery cells on the support rack, electrolyte filling and associated work as recommended by MANUFACTURER is included in the scope.Installation of battery MCCB with enclosure at the location indicated in the applicable layouts is included in the scope.Installation of Battery monitoring system as applicable is included in the scope. Testing and precommissioning activities, commissioning assistance as required by MANUFACTURER's supervisor is included in the scope. First charge, Discharge and again charging of battery bank is included in scope.Minor civil work such as chipping, grouting for fixing of equipment / assemblies and replastering the same as per the site requirement (including the supply of consumable material for the same) is included in the scope.Fabrication and installation of steel support structure / supporting frames for various equipment / assemblies as per the site requirement, is considered separately in SECTION - F.Supply of all fixing hardware as per the site requirement is included in the scope. |
| 641 | TAG : 1U64-SS16-ECH-503 (For Switchgear Control) |
| 642 | Battery charger (Dual redudant)Rating : 110 VDC, 160 A, Battery charger with seperate DCDB Construction : Non Compartmentalised, Single / Double frontApprox. Dimensions (LxBxH) : 2200 x 800 x 2000 mm Approx. Weight : 600 kgs (Overall) Mounting : On Floor |
| 643 | Battery bank : 1U64-SS16-BAT-503A/B Battery type : Ni-CdNo, of cells : 95Rating : 300 AHMounting : floor mounted battery rack, multi-tier |
| 644 | DCDB : 1U64-SS16-DCDB-503-1 No.Rating : 110 VDC, 160 AConstruction : Compartmentalised, Single frontApprox. Dimensions (LxBxH) : 6500 x 450 x 2200 mmApprox. Weight : 850 kgs (Overall)Mounting : On Floor |
| 645 | Battery Isolator (MCCB) - 2 Nos.Enclosure : FlameproofMounting : on wall |
| 646 | Cell Booster (Portable type) - 2 Nos.Approx. Dimensions (LxBxH) : 600 x 600 x 500 mm |
| 647 | TAG : 1U64-SS16-ECH-504 (For DC Critical Lighting) |
| 648 | Battery charger (Single)Rating : 110 VDC, 75 A, Battery charger with seperate DCDBConstruction : Non Compartmentalised, Single / Double frontApprox. Dimensions (LxBxH) : 600 x 600 x 1500 mmApprox. Weight : 200 kgs (Overall) Mounting : On Floor |
| 649 | Battery bank : 1U64-SS16-BAT-504Battery type : Ni-CdNo, of cells : 95Rating : 140 AHMounting : floor mounted battery rack, Two-tier |
| 650 | DCDB : 1U64-SS16-DCDB-504- 1 No.Rating : 110 VDC, 75 AConstruction : Compartmentalised, Single frontApprox. Dimensions (LxBxH) : 1200 x 450 x 1600 mmApprox. Weight : 150 kgs (Overall)Mounting : On Floor |
| 651 | Battery Isolator (MCCB)-1 NosEnclosure : FlameproofMounting : on wall |
| 652 | Cell Booster (Portable type) - 2 Nos.Approx. Dimensions (LxBxH) : 600 x 600 x 500 mm |
| 653 | AC UPS AND BATTERY |
| 654 | Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of equipment / assemblies, assembling and installation of components / devices supplied separately - as recommended by MANUFACTURER / applicable construction documents, stenciling with paint on equipment enclosures as required and other associated work so as to ensure the completeness of installation workAssembly of battery rack, placement of battery cells on the support rack, electrolyte filling and associated work as recommended by MANUFACTURER is included in the scope.Installation of battery MCCB with enclosure at the location indicated in the applicable layouts is included in the scope.Installation of Battery monitoring system as applicable is included in the scope. Testing and precommissioning activities, commissioning assistance as required by MANUFACTURER's supervisor is included in the scope. First charge, Discharge and again charging of battery bank is included in scope.Minor civil work such as chipping, grouting for fixing of equipment / assemblies and replastering the same as per the site requirement (including the supply of consumable material for the same) is included in the scope. Fabrication and installation of steel support structure / supporting frames for various equipment / assemblies as per the site requirement, is considered separately in SECTION - F.Supply of all fixing hardware as per the site requirement is included in the scope. |
| 655 | TAG : 1U64-SRR6-UPS-501 |
| 656 | UPS Rating : 115 VAC, 200 kVA, Parallel redudant UPS with common bypass and separate ACDBConstruction : Non Compartmentalised, Single / Double frontApprox. Dimensions (LxBxH) : 8000 x 1200/1000 x 2100 mm (Overall)Mounting : On False floor supported with structural steel base frame |
| 657 | Battery bank : 2 setsBattery type : Ni-CdNo, of cells (Per set) : ~ 375Rating of cell : ~ 650 AHMounting : floor mounted battery rack, multi-tier |
| 658 | ACDB : 1 No.Rating : 115 V AC, 2000 AConstruction : Compartmentalised, Single / Double frontApprox. Dimensions (LxBxH) : 13000 x 850 x 2200 mmMounting : On False floor supported with structural steel base frame |
| 659 | Battery Isolator (MCCB)-2 NosEnclosure : FlameproofMounting : on wall / Floor |
| 660 | Cell Booster (Portable type) - 1 Nos.Approx. Dimensions (LxBxH) : 700 x 700 x 600 mm |
| 661 | MV (415V) VARIABLE FREQUENCY DRIVES, THYRISTORIZED HEATER CONTROL PANELS, EXCITATION CONTROL PANELS etc. |
| 662 | Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of equipment and accessories, assembling and installation of components / devices supplied separately - as recommended by MANUFACTURER / applicable construction documents, stenciling with paint on equipment enclosures as required and other associated work so as to ensure the completeness of installation work. Testing and precommissioning activities, commissioning assistance as required by MANUFACTURER's supervisor is included in the scope. Minor civil work such as chipping, grouting for fixing of equipment / assemblies and replastering the same as per the site requirement (including the supply of consumable material for the same) is included in the scope. Fabrication and installation of steel support structure / supporting frames for equipment / accessories as per the site requirement, is considered separately in SECTION - F.Supply of all fixing hardware as per the site requirement is included in the scope. |
| 663 | TAG : 1P24-EEH-0981Rating : 415V, 1746 kWNo of shipping sections : 6Approx. Maximum Dimensions (LxBxH) : 2800 x 1200 x 2250 mm (per shipping section)Approx. Dimensions (LxBxH) : 12000 x 1000 / 1200 x 2250 mm (overall)Approx. Weight : 8000 kgs (overall)Mounting : On floor |
| 664 | TAG : 1P24-EEH-0882Rating : 415V, 103 kWApprox. Dimensions (LxBxH) : 1300 x 600 x 2050 mm Approx. Weight : 1000 kgs (overall)Mounting : On floor |
| 665 | TAG : 1P23-EEH-6383Rating : 415V, 40 kWApprox. Dimensions (LxBxH) : 900 x 500 x 2225 mm Approx. Weight : 700 kgs (overall)Mounting : On floor |
| 666 | TAG : 1P23-EEH-6382Rating : 415V, 37 kWApprox. Dimensions (LxBxH) : 900 x 500 x 2225 mm Approx. Weight : 700 kgs (overall)Mounting : On floor |
| 667 | TAG : 1P23-EEH-6381Rating : 415V, 425 kWApprox. Dimensions (LxBxH) : 2100 x 1000 x 2375 mm Approx. Weight : 1600 kgs (overall)Mounting : On floor |
| 668 | TAG : 1P23-EEH-0882Rating : 415V, 302 kWApprox. Dimensions (LxBxH) : 1800 x 1000 x 2375 mm Approx. Weight : 1500 kgs (overall)Mounting : On floor |
| 669 | TAG : 1P23-EEH-6385Rating : 415V, 302 kWApprox. Dimensions (LxBxH) : 1000 x 250 x 600 mm Approx. Weight : 250 kgs (overall)Mounting : On wall |
| 670 | TAG : 1P23-KAM-2782AB-SYNC.(Excitation Panels for H2 Rich Gas Compressor Motor)Construction : Floor mounting, single frontApprox. Overall Dimensions (LxBxH)mm : 1650 x 750 x 2265 mm Approx. Weight : 1000 kgMounting : On floor |
| 671 | TAG : 1P23-PM-8801A/B-VFD, 1P22-PM-3902A/B-VFD,1P22-PM-4001A/B-VFD Rating : 415V, up to 5.5 kWApprox. Dimensions (LxBxH) : 800 x 600 x 2000 mm Approx. Weight : 500 kgs (overall)Mounting : On floor |
| 672 | TAG : 1P24-EAM-0953A-VFD, 1P24-EAM-2451A/B-VFD , 1P23-EAM-2651A/B/C-VFD Rating : 415V, Above 5.5 kW, up to 15 kWApprox. Dimensions (LxBxH) : 1000 x 600 x 2000 mm Approx. Weight : 700 kgs (overall)Mounting : On floor |
| 673 | TAG : Various (VFD Panels)Rating : 415V, Above 15 kW, up to 30 kWApprox. Dimensions (LxBxH) : 1000 x 600 x 2000 mm Approx. Weight : 800 kgs (overall)Mounting : On floor |
| 674 | INDUCTION MOTORS AND CANOPIESAlignment as required for the accessories such as terminal box, assembling and installation of components / devices supplied separately as recommended by MANUFACTURER / applicable construction documents, stenciling with paint on equipment enclosures as required and other associated work so as to ensure the completeness of installation work.Checking of all interface connections, change of grease in bearings, wherever required, including supply of approved type of grease, no load/full load running of motor, including all labour and materials, as per specifications of this tender and directions of Site Engineer-in-Charge.Testing, precommissioning and commissioning activities are included in the scope. |
| 675 | MV (415V) Motors |
| 676 | Upto 3.0 kW |
| 677 | 3.7 kW to 15 kW |
| 678 | 18.5 kW to 37.0 kW |
| 679 | 45.0 kW to 90 kW |
| 680 | 110 kW to160 kW |
| 681 | Above 160 kW up to 315 kW |
| 682 | HV (6.6 kV) Motors |
| 683 | Above 160 kW up to 400 kW |
| 684 | Above 400 kW up to 800 kW |
| 685 | Above 800 kW up to 1200 kW |
| 686 | Above 1200 kW up to 1500 kW |
| 687 | Above 1500 kW up to 3000 kW |
| 688 | Above 3000 kW up to 7500 kW |
| 689 | Canopies |
| 690 | Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of canopy for the motor - as per applicable construction documents, stenciling with paint on equipment enclosures as required and other associated work so as to ensure the completeness of installation work, minor modifications (cutting, drilling etc.) in the canopy fitting arrangemet if required.Supply of all fixing hardware as per the site requirement is included in the scope. |
| 691 | MV (415V) Motors |
| 692 | Upto 3.0 kW |
| 693 | 3.7 kW to 15 kW |
| 694 | 18.5 kW to 37.0 kW |
| 695 | 45.0 kW to 90 kW |
| 696 | 110 kW to160 kW |
| 697 | Above 160 kW up to 315 kW |
| 698 | HV (6.6 kV) Motors |
| 699 | Above 160 kW up to 400 kW |
| 700 | Above 400 kW up to 800 kW |
| 701 | Above 800 kW up to 1200 kW |
| 702 | Above 1200 kW up to 1500 kW |
| 703 | Above 1500 kW up to 3000 kW |
| 704 | Above 3000 kW up to 7500 kW |
| 705 | MV (415V) Electric Heaters : Testing and commissioning of Electric Heaters of following ratings and checking of all interface connections including Electric Heater Junction box installation along with associated cables, terminations. Providing assistance for successful commissioning of heaters, laying and termination of braided cables to heater terminal box (as applicable), testing and commissioning works, including all labour and materials, as per approved drawings, specifications of this tender and directions of Site Engineer-in-Charge. |
| 706 | up to 5.5 kW |
| 707 | Above 5.5 kW but upto 22 kW. |
| 708 | Above 22 kW but upto 45 kW |
| 709 | Above 45 kW but upto 160 kW |
| 710 | Above 160 kW but upto 450 kW. |
| 711 | Above 1000 kW but upto 1750 kW. |
| 712 | LOCAL CONTROL STATIONS (LCS) |
| 713 | Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of equipment, assembling and installation of components / devices supplied separately - as recommended by MANUFACTURER / applicable construction documents, stenciling with paint on equipment enclosures as required and other associated work so as to ensure the completeness of installation work.Testing, precommissioning and commissioning activities are included in the scope.Supply of installation materials (excluding structure steel) as per installation details-power and applicable construction documents are included in the scope.Fabrication and installation of steel support structure / supporting frames for equipment as per the site requirement, is considered separately in SECTION - F. |
| 714 | Industrial/ Explosive Atmospheres type LCS (wall / concrete / steel structure mounted) |
| 715 | INSTALLATION OF SWITCH-BOARDS, RELAY AND CONTROL PANELS, ANNUNCIATION PANELS, UPS SYSTEM, BATTERY CHARGERS, DISTRIBUTION BOARDS, CUBICLES WITH ELECTRICAL EQUIPMENT, VSD/ Softstarter PANELS, RTCC panles, MISC .ELECTRICAL PANELS, ETCSwitchboards / panels indicated below excludes items already considered in sr. no. A/5 to A/9 above |
| 716 | Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of various shipping sections / assemblies, assembling and installation of components / devices supplied separately - as recommended by MANUFACTURER / applicable construction documents, interpanel wiring, stenciling with paint on equipment enclosures as required and other associated work so as to ensure the completeness of installation work.Testing, precommissioning and commissioning activities are included in the scope.Minor civil work such as chipping, grouting for fixing of equipment and replastering the same as per the site requirement (including the supply of consumable material for the same) is included in the scope. Supply of all fixing hardware as per the site requirement is included in the scope.Fabrication and installation of steel support structure / supporting frames for various equipment/ assmblies as per the site requirement, is considered separately in SECTION - F.Supply of all fixing hardware as per the site requirement is included in the scope. |
| 717 | Weight of the Unit above 100 upto 500 kg. |
| 718 | Weight of the Unit above 500 upto 1000 kg. |
| 719 | Weight of the Unit above 1000 upto 1500 kg. |
| 720 | Weight of the Unit above 1500 upto 3000 kg. |
| 721 | Weight of the Unit above 3000 upto 5000 kg. |
| 722 | ELECTRICAL HEAT TRACING SYSTEM |
| 723 | Installation of Heat Tracing System comprising Power Distribution Board-cum-Control Panel, Heat Tracers and Accessories (Connector, Junction Box, fastening material, etc.), Temp. sensing elements, Thermostats, etc. as per Specification (Doc no. TK-1P22A-EL-SPE-0031)Testing, precommissioning and commissioning activities are included in the scope.Supply of installation materials, fixing hardware etc as per Installation details and applicable construction documents are included in the scope |
| 724 | CABLE / WIRE LAYING, TERMINATION AND CABLE ROUTING SYSTEMS |
| 725 | CABLE LAYING |
| 726 | Handling, shifting of cable drums from site-store / yard to the installation location, unpacking, laying of cables / wires in cable trays (either located above ground or inside RCC cable trenches) / directly buried underground / in sand filled cable trenches (trench constructed by others) / in culverts, duct banks/ through above ground conduits (PVC / GI) clamped on wall or structure or through floor conduits (excluding lighting circuit cables, from LDB / ELDB onwards upto the lighting fixtures) - as recommended by MANUFACTURER / applicable construction documents and other associated work so as to ensure the completeness of installation work. Job also includes return of unused cable/drums to the Owner's store & removal of empty drum/ scrap cables to Owner's Scrap Yard.Testing, precommissioning and commissioning activities are included in the scope. Supply and installation of certified trefoil clamps of non-magnetic materia for 1 core cables, spacer bars and saddles, dressing of cables using Stainless Steel cable ties, cable tags(RFID tags) and ferrules (including all fixing hardware) as per the site requirement are included in the scope.The motorized winch required for cable pulling shall be arrange by contractor and no separate payment for the same will be madeMinor civil work such as chipping / drilling of through-holes / cutouts in floor / walls, replastering and making area good after work done, providing sleeves during the cable laying as per the site requirement and replastering the same (including the supply of consumable material for the same) is included in the scope. Supply and Installation of cable route markers with warning tapes (as applicable) shall be as per 'Installation Details - Power' and applicable construction documents is included in the scope |
| 727 | HV CABLES |
| 728 | Cables with OD above 40 mm but upto 60 mm. |
| 729 | Cables with OD above 60 mm but upto 80 mm. |
| 730 | LV Power Cables Aluminium condutor cables |
| 731 | Cables with OD upto 20 mm. |
| 732 | Cables with OD above 20 mm but upto 30 mm. |
| 733 | Cables with OD above 30 mm but upto 40 mm. |
| 734 | Cables with OD above 40 mm but upto 50 mm. |
| 735 | Cables with OD above 50 mm but upto 60 mm. |
| 736 | Cables with OD above 60 mm but upto 80 mm. |
| 737 | Cables with OD above 80 mm but upto 100 mm. |
| 738 | Cables with OD above 100 mm but upto 120 mm. |
| 739 | LV Power/ Control/ Signal / Fire alram / Communication / Telephone etc - Copper condutor cables |
| 740 | Cables with OD upto 20 mm. |
| 741 | Cables with OD above 20 mm but upto 30 mm. |
| 742 | Cables with OD above 30 mm but upto 40 mm. |
| 743 | Cables with OD above 40 mm but upto 50 mm. |
| 744 | Cables with OD above 50 mm but upto 60 mm. |
| 745 | EARTHING CABLES (laid above ground/ Undergorund)1100V Al / Cu conductor, PVC insulated, unarmoured earthing cables :- Laying and termination of earthing cables including supply of lug.laying,clamping and connecting individual equipment to the earthstrip or earth plate with following sizes of Cables including supply of required lugs, all hardware for connections, Including all labour and materails, as per approved drawings, specifications of this tender and directions of Engineer-in-charge |
| 746 | 1 C x 6 sq.mm Cu Stranded, PVC insulated Green/Yellow cable |
| 747 | 1 C x 16 sq.mm Cu Stranded, PVC insulated Green/Yellow cable |
| 748 | 1 C x 25 sq.mm Cu Stranded, PVC insulated Green/Yellow cable |
| 749 | 1 C x 50 sq.mm Cu Stranded, PVC insulated Green/Yellow cable |
| 750 | 1 C x 95 sq.mm Cu Stranded, PVC insulated Green/Yellow cable |
| 751 | 1 C x 25 sq.mm Al Stranded, PVC insulated Green/Yellow cable |
| 752 | 1 C x 35 sq.mm Al Stranded, PVC insulated Green/Yellow cable |
| 753 | 1 C x 50 sq.mm Al Stranded, PVC insulated Green/Yellow cable |
| 754 | 1 C x 70 sq.mm Al Stranded, PVC insulated Green/Yellow cable |
| 755 | 1 C x 120 sq.mm Al Stranded, PVC insulated Green/Yellow cable |
| 756 | GI Wire ropes |
| 757 | Laying,clamping and connecting individual equipment to the earthstrip or earth plate with following sizes of G.I wire / G.I wire rope, including supply of required lugs, conductors, all hardware for connections, Including all labour and materails, as per approved drawings, specifications of this tender and directions of Engineer-in-charge |
| 758 | 8 SWG Solid GI wire |
| 759 | 10 mm (3/8\\") Dia. flexible GI wire rope |
| 760 | 16 mm (5/8\\") Dia. flexible GI wire rope |
| 761 | FIBRE OPTIC CABLES : \\"LAYING OF FIBRE OPTIC CABLE:The job includes collection and transportation of all required material from store to work site, laying of FO cable of various sizes along with HDPE conduits inclusive of supply of HDPE conduits, cutting of the cable as per actual measurement/ cableschedule, tagging at definite span length, dressing & clamping, providing identification tags at both ends, as required and complete the job in all respects as per specification, drawings and instructions of Engineer In-ChargeHDPE conduit shall be as per IS-4984 or as per equivalent IEC code. The outer sheath colour of HDPE conduits shall be orange with black for the fittings throughout the fibre optic cable run. |
| 762 | Fibre Optic Cable - up to 8 Fibre |
| 763 | Fibre Optic Cable - 12 Fibre |
| 764 | Fibre Optic Cable - 24 Fibre |
| 765 | FLEXIBLE CONDUCTOR CABLES |
| 766 | 650V / 1100V (Uo / U) voltage grade, Multistranded Cu conductor, PVC insulated, flexible cable |
| 767 | Cables with OD upto 20 mm. |
| 768 | Cables with OD above 20 mm but upto 30 mm. |
| 769 | Special cables |
| 770 | Silicon Insulated Flexible cable / Uninyvin cables |
| 771 | Cables with OD upto 20 mm. |
| 772 | Cables with OD above 20 mm up to 40 mm |
| 773 | CAT 6A Cable |
| 774 | MODBUS SERIAL RS485 |
| 775 | CABLE GLANDING AND TERMINATION (HV)(Industrial / For Explosive Atmospheres) |
| 776 | Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembly and installation of HV cable termination kit and cable glands with PVC hoods, installation of components supplied separately - as recommended by MANUFACTURER / applicable construction documents, installation of tinned copper lug, drilling and treading of gland plate, termination of cable at designated location and other associated work so as to ensure the completeness of installation work. |
| 777 | Cable termination shall be carried out by experienced, competent & certified personnel from the termination kit MANUFACTURER / installation CONTRACTOR. |
| 778 | Glanding and Termination of 6.6 / 6.6 kV (UE) voltage grade, Al / Cu conductor, XLPE insulated, screened, armoured power cable |
| 779 | 3C x 240 sq.mm A2XCEFY |
| 780 | 1C x 630 sq.mm A2XCEFY |
| 781 | HV Cable termination kit Separable Connector type (suitable for indoor installation) 6.6kV (UE) HV cables grade, Al conductor, XLPE insulated, screened, armoured power cable. Motor cable TB is suitable for Elastimold Separable connector. The Separable connectors will be supplied by motor manufacturer and will be free issue to the contractor. Contractor to supply THREE CORE HEAT SHRINKABLE BREAKOUT KIT and carry out the complete installation of the separable connector kit. |
| 782 | 3C x 240 sq.mm |
| 783 | Glanding and Termination of 33 / 33 kV (Uo / U)grade, Al conductor, XLPE insulated, screened, armoured power cable |
| 784 | 1C x 630 sq.mm A2XCEWaY |
| 785 | CABLE GLANDING AND TERMINATION (MV)(Industrial / For Explosive Atmospheres) |
| 786 | Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembly and installation of cable glands (industrial / For Explosive Atmospheres type) with PVC hoods, installation of components supplied separately - as recommended by MANUFACTURER / applicable construction documents, installation of lug, drilling and treading of gland plate, termination of cable (excluding lighting circuit cables, from SLDB / ESLDB onwards upto the lighting fixtures) at designated location and other associated work so as to ensure the completeness of installation work.Scope shall include drilling of holes, if not provided by manufacturer.Supply of Crimping type Lugs shall be included in the cost. Type of Lug shall be as per type of terminals provided in equipment. For CT circuits Ring type lug shall be used. For Control cables,Tinned copper lugs shall be insulated, Ring / Pin / Fork crimping type as per terminal requirments.For Power cables, lugs shall be tinned copper / Aluminium (Tinned Copper lugs for copper conductor cable and Aluminium Lugs for Aluminium conductor cables ) tubular type, heavy duty long barrel lugs for bolted connection Supply and installation of Bi-metallic washer if the material of bus bar and Lugs are dissimilar are included in Contractor scope. |
| 787 | MV POWER CABLESGlanding and Termination of 650 / 1100V (Uo / U) voltage grade, Al / Cu conductor (stranded / solid), XLPE insulated, screened, armoured power / lighting cables |
| 788 | Cables with OD up to 20 mm |
| 789 | Cables with OD above 20 mm but up to 30 mm |
| 790 | Cables with OD above 30 mm but up to 40 mm |
| 791 | Cables with OD above 40 mm but up to 50 mm |
| 792 | Cables with OD above 50 mm but up to 60 mm |
| 793 | Cables with OD above 60 mm but up to 80 mm |
| 794 | MV CONTROL ,FIRE ALARM AND COMMUNICATION CABLES Glanding and Termination of 650 / 1100V (Uo / U) voltage grade, Al / Cu conductor (stranded / solid), PVC/XLPE insulated, screened, armoured control, Fire Alarm and Communication Cables |
| 795 | All sizes from 2 to 7 cores and upto 2.5 sq. mm |
| 796 | All sizes from 8 to 16 cores and upto 2.5 sq. mm |
| 797 | All sizes from 17 to 24 cores and upto 2.5 sq. mm |
| 798 | All sizes from 1P to 4P and upto 2.5 sq. mm |
| 799 | All sizes from 5P to 10P and upto 2.5 sq. mm |
| 800 | All sizes from 11P to 15P and upto 2.5 sq. mm |
| 801 | All sizes from 16P to 30P and upto 2.5 sq. mm |
| 802 | All sizes from 30P to 50P and upto 2.5 sq. mm |
| 803 | All sizes from 50P to 100P and upto 2.5 sq. mm |
| 804 | All sizes from 1T to 8T and upto 2.5 sq. mm |
| 805 | Glanding and Termination of FIBRE OPTIC CABLES (Single Mode / Multi Mode)Scope includes Supply of kit, preparation of all fibres and splicing / patching, OTDR measurement, Supply of adequate consumables for the execution of the work (such as fibre optic connectors suitable for the application) testing, tools & tackles, manpower, etc. all complete as per direction of Engineer-in-Charge is included in scope. |
| 806 | Fibre Optic Cable - 6 / 8 Fibre |
| 807 | Fibre Optic Cable - 12 Fibre |
| 808 | Fibre Optic Cable - 24 Fibre |
| 809 | Termination of armoured Jelly filled cables and connection of leads excluding the supply of cable glands and lugs but including fixing of cable glands, supply and fixing of PVC shrouds for outdoor terminations, cutting, stripping of cable insulation, crimping the lug on to the conductor, clamping of the cable- cores, marking with wire number, ferrules etc., including all labour and materials, as per approved drawings, specifications of this tender and directions of Site Engineer-in-Charge |
| 810 | All sizes from upto 5 pair |
| 811 | All sizes above 5 pair upto 30pair |
| 812 | All sizes above 30 pair upto 50pair |
| 813 | All sizes above 50 pair upto 100pair |
| 814 | WIRES AND FLEXIBLE CONDUCTOR CABLES |
| 815 | Termination of 1100V, Multistranded Cu conductor, PVC insulated, flexible wires |
| 816 | Cables with OD upto 20 mm. |
| 817 | Cables with OD above 20 mm but upto 30 mm. |
| 818 | Glanding & Termination of Special cables |
| 819 | Silicon Insulated Flexible cable / Uninyvin cables |
| 820 | Cables with OD upto 20 mm. |
| 821 | Cables with OD above 20 mm up to 40 mm |
| 822 | CAT 6A Cable (The scope includes supply of RJ 45 plug) |
| 823 | Modbus RS 485 |
| 824 | CABLE JOINTING |
| 825 | Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembly and installation of straight through joint kits, installation of components supplied separately - as recommended by MANUFACTURER / applicable construction documents, and other associated work so as to ensure the completeness of installation work.Civil work such as construction of concrete chamber with cover (for cables directly buried underground) as per the site requirement (including the supply of consumable material for the same) is included in the scope. |
| 826 | HV CABLES |
| 827 | Straight through joint for 6.6 / 6.6 kV (UE) voltage grade, Al / Cu conductor, XLPE insulated, screened, armoured power cable |
| 828 | 3C x 240 sq.mm A2XCEFY (UE) |
| 829 | Straight through joint for 33 / 33 kV (Uo / U)grade, Al conductor, XLPE insulated, screened, armoured power cable |
| 830 | 1C x 630 sq.mm A2XCEWaY |
| 831 | MV CABLES |
| 832 | 650 / 1100V (Uo / U) voltage grade, Al / Cu conductor (stranded / solid), XLPE insulated, screened, armoured power / control / lighting cables |
| 833 | Cables with OD upto 20 mm. |
| 834 | Cables with OD above 20 mm but upto 30 mm. |
| 835 | Cables with OD above 30 mm but upto 40 mm. |
| 836 | Cables with OD above 40 mm but upto 50 mm. |
| 837 | Cables with OD above 50 mm but upto 60 mm. |
| 838 | Cables with OD above 60 mm but upto 80 mm. |
| 839 | Installation of Jointing kits (for joints between Single/ MultiMode Fiber Optic armoured cables), Preparation of all fibres, splicing / patching, OTDR measurement, Supply of adequate consumables for the execution of the work (such as fibre optic connectors suitable for the application),testing, tools & tackles, manpower, etc. all complete as per direction of Engineer-in-Charge. |
| 840 | 6/8 Fiber |
| 841 | 24 Fiber |
| 842 | PREFABRICATED CABLE TRAYS |
| 843 | Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembly and installation of prefabricated galvanized steel ladder type / perforated cable trays / FRP cable trays (above ground or inside concrete trenches) with all associated accessories such as bends, reducers, T-joints, fixing clamps, earthing continuity conductors etc. - as recommended by MANUFACTURER / applicable construction documents, fixing of cable trays / associated accessories to steel supports, stenciling with paint as required and other associated work so as to ensure the completeness of installation work.Site fabrication of cable tray accessories such as bends, reducers, T-joints etc. from cable tray straight runs as per the site requirement is included in the scope.For prefabricated cable trays accessories such as bends, reducers, T-joints etc. installtion of coupler plates is included in scope.For Ladder type Cable tray, the Bends/ Risers/ Tees are prefabricated/site fabricated. Cable tray bends/ riser/Tees etc on pipe rack are preferebally prefabricated. Rest of the bends can be site fabricated as per instructions given by Engineer-in-Charge. For perforated trays upto and including 150mm, the Bends/ Risers/ Tees/ Redcuers with covers shall be site fabricated as per instructions given by Engineer-in-ChargeFabrication and installation of steel support / bracket for cable trays / accessories as per the site requirement, is considered separately in this SOR.Supply of all fixing hardware as per the site requirement is included in the scope. |
| 844 | Cable Trays Perforated (GI) and Accessories |
| 845 | Installation of cable tray accessories such as bends, reducers, T-joints etc. is considered in cable tray running length. |
| 846 | 50 mm wide |
| 847 | 100 mm wide |
| 848 | 150 mm wide |
| 849 | Cable Ladders (GI) and Accessories |
| 850 | Installation of cable tray accessories such as bends, reducers, T-joints etc. is considered in cable tray running length. |
| 851 | 150 mm wide |
| 852 | 300 mm wide |
| 853 | 600 mm wide |
| 854 | Cable Tray Covers (Bottom / TOP) (GI) and Accessories |
| 855 | 100 mm wide |
| 856 | 150 mm wide |
| 857 | 300 mm wide |
| 858 | 600 mm wide |
| 859 | Separators for Cable Ladders (GI) |
| 860 | 300 mm / 600 mm wide |
| 861 | CONDUITS FOR CABLE LAYING / PROTECTION |
| 862 | Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembly and installation of heavy duty rigid GI / PVC conduits on wall / concrete / steel structure (with edge protection grommet at either ends for GI conduits), cutting, bending of conduits and other associated work so as to ensure the completeness of installation work.Installation of GI clamps, reducers / adaptors for the conduits, tees, pull boxes as per the site requirement and the associated work is included in the scope.Supply of waterproof compound (of reputed make) and sealing of conduit openings after laying of cable by applying the same is included in the scope. Civil work such as chipping / drilling of through-holes / cutouts in floor / walls (as per the site requirement) and replastering and making area good after installation of conduits as per the site requirement (including the supply of consumable material for the same) is included in the scope.Supply of all fixing hardware as per the site requirement is included in the scope. Installation of conduits and associated accessories for 'Point Wiring for Office buildings / Control rooms / Other rooms with false ceiling' is considered separately in SECTION - C |
| 863 | Rigid GI conduits |
| 864 | 25 mm nominal dia |
| 865 | 50 mm nominal dia |
| 866 | 100 mm nominal dia |
| 867 | 150 mm nominal dia |
| 868 | Rigid GI conduits RED coloured (For Fire Alarm System cables) |
| 869 | 25 mm nominal dia |
| 870 | 50 mm nominal dia |
| 871 | Heavy duty PVC conduits |
| 872 | 25 mm nominal dia |
| 873 | 50 mm nominal dia |
| 874 | Flexible PVC conduits |
| 875 | 25 mm nominal dia |
| 876 | LIGHTING, SMALL POWER, WELDING SOCKETS AND JUNCTION BOXES |
| 877 | LIGHTING |
| 878 | Installation of Industrial / For Explosive Atmospheres type lighting fixtures Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of lighting fixtures, assembling and installation of components / accessories such as lamps, chokes, condensers, reflectors, control gear box for non-integral fixtures etc. supplied separately - as recommended by MANUFACTURER / applicable construction documents, checking of internal wiring, stenciling with paint on equipment enclosures as required and other associated work so as to ensure the completeness of installation work'The scope is inclusive of Installation of loop-in / loop-out junction box / connector &associated with each fixtures- as per applicable installation details with associated cabling, glanding, termination of cable from Junction box / connectors toLight fixture.Installation of lighting fixtures shall be as per 'Installation Details - Lighting' and applicable construction documents.Testing, precommissioning and commissioning activities are included in the scope.Installation of lighting fixtures shall be as per 'Installation Details - Lighting' and applicable construction documents. The supply of installation materials (except lighting poles and structure steel) as per \\"Installation Details-Lighting\\" and including any additional material as per site requirement so as to ensure the completeness of installation work is included in the scope. |
| 879 | Installation of Poles are considered separately.Fabrication, surface preparation, painting and installation of steel support of steel support structure / supporting frames as per the site requirement for above shall be considered separately in SECTION - F |
| 880 | Lighting Fixtures |
| 881 | Fluorescent lighting fixtures |
| 882 | Installation Type : L09A |
| 883 | Installation Type : L09B |
| 884 | Installation Type : L09C |
| 885 | Installation Type : L10 |
| 886 | Well glass lighting fixtures |
| 887 | Installation Type : L07A |
| 888 | Installation Type : L07B |
| 889 | Installation Type : L07C |
| 890 | Installation Type : L07D |
| 891 | Installation Type : L07E |
| 892 | Installation Type : L07F |
| 893 | Installation Type : L04 |
| 894 | Installation Type : L05 |
| 895 | Installation Type : L06 |
| 896 | Medium bay / high bay lighting fixtures |
| 897 | Installation Type : L13A |
| 898 | Installation Type : L13B |
| 899 | Installation Type : L13C |
| 900 | Flood lighting fixtures |
| 901 | Installation Type : L12 |
| 902 | Installation Type : L02 |
| 903 | Installation Type : L11 |
| 904 | Emergency lighting fixture with built-in battery (Installation types same as listed under Section C1.1.1 to C1.1.5) |
| 905 | Insatallation Type : L09B |
| 906 | Emergency EXIT sign with built-in battery |
| 907 | Installation Type : L16 |
| 908 | Installation Type : L17 |
| 909 | Installation Type : L18 |
| 910 | Installation Type : L19 |
| 911 | Installation Type : L20 |
| 912 | Installation Type : L21 |
| 913 | Aviation light (flashing / steady burning) with controller |
| 914 | Installation Type : L14A |
| 915 | Installation Type : L14B |
| 916 | Installation Type : L14C |
| 917 | Vessel lamps |
| 918 | Installation Type : Flange Mounted on Sight Glasses |
| 919 | Installation of Lighting PolesInstallation, alignment & earthing of single arm GI lighting pole as per approved drawing along with supply of fixing hardware like U clamp & bolt, for platform mounted pole. Including welding, structuralworks, paint and all sundry materials as required. For ground mounted poles it includes supply and fixing of G.I pipes, G.I flat for earthing purpose, steel, base plates, paint and all sundry materials as required. Including all labour and materials complete as per approved drawings, specification of this tender and directions of Engineer-in-charge. This shall include local transportation from storage area to actual place of installation by contractor's own lifting & transporting arrangement.The installation of Lighting pole will be carried out as per IFC drawing & suit to site conditions to avoid fouling with other Piping, Structure & access ways. Refer tender documentation, including Typical installation drawings, RFC construction drawings and as per direction of Engineer In-Charge |
| 920 | Installation details : L04 |
| 921 | Installation details : L05 |
| 922 | Installation details : L11 |
| 923 | Installation details : L14A |
| 924 | Junction boxes for LightingHandling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of junction boxesand associated accessories on wall / concrete / steel structure - as recommended by MANUFACTURER / applicable construction documents, checking of internal wiring, stenciling with paint on equipment enclosures as required and other associated work so as to ensure the completeness of installation work.Testing, precommissioning and commissioning activities are included in the scope. Minor civil work such as chipping, grouting for fixing of various equipment, replastering and making area good etc.as per the site requirement (including the supply of consumable material for the same) is included in the scope. Installation of Junction Boxes shall be as per 'Installation Details - Lightingr' and applicable construction documents.The supply of installation materials (excludingstructure steel) as per \\"Installation Details-Lighting\\" and including any additional material as per site requirement so as to ensure the completeness of installation work is included in the scope.Supply of all fixing hardware as per the site requirement is included in the scope.Fabrication, surface preparation, painting and installation of steel support of steel support structure / supporting frames as per the site requirement for above shall be considered separately in SECTION - FInstallation of loop-in / loop-out junction box / connector are covered in the installation of respective light fixture installation. The qty indicated below are lighting junction boxes required for lighting branch circuits/ |
| 925 | Installation Type : L08B / L08C / L08D / L08E / L08F / L08G |
| 926 | Point Wiring for Office buildings / Control rooms / Other rooms with false ceiling |
| 927 | Installation of surface wiring / concealed wiring (in brick wall / decorative type aluminium partition in office rooms) using 2.5sq. mm flexible copper PVC wires, GI / PVC conduits, assembly and installation / embedding of heavy duty rigid GI / PVC conduits on / in wall / concrete structure (with edge protection grommet at either ends for GI conduits), cutting, bending of conduits - as per the applicable construction documents and other associated work so as to ensure the completeness of installation work.Installation of GI clamps, reducers / adaptors for the conduits, tees, pull boxes as per the site requirement and the associated work is included in the scope. Civil work such as chipping / drilling of through-holes / cutouts in walls (as per the site requirement) and replastering and making area good after embedding of conduits as per the site requirement (including the supply of consumable material for the same) is included in the scope.Testing, precommissioning and commissioning activities are included in the scope.Supply 2.5 sq.mm flexible copper PVC wires as requried, supply GI conduits for SURFACE CONDUIT WIRING / PVC conduits for CONCEALED CONDUIT WIRING and associated accessoreis such as GI clamps, reducers / adaptors for the conduits, tees, pull boxes, along with all fixing hardware as per the site requirement is included in the scope.For installation of wires above false ceiling / below false floor, conduits can be installed on surface of wall / concrete structure, after consultation with OWNER / CONSULTANT. Elsewhere, installation of wires shall be in concealed conduits. |
| 928 | Primary Circuit (From SLDB / ESLDB / Lighting Junction Box upto Switch Box for local control) |
| 929 | 1 point (wire length approx. 20m) |
| 930 | 1 point (wire length approx. 30m) |
| 931 | 1 point (wire length approx. 40m) |
| 932 | 1 point (wire length approx. 50m) |
| 933 | 1 point (wire length approx. 60m) |
| 934 | Secondary Circuit (From Switch Box for local control upto the lighting fixture / 5A/15A switch socket outlet / fan etc.) |
| 935 | 1 point (total wire length approx. 7m) |
| 936 | 2 point (total wire length approx. 15m) |
| 937 | 3 point (total wire length approx. 22m) |
| 938 | 4 point (total wire length approx. 30m) |
| 939 | 5 point (total wire length approx. 40m) |
| 940 | 6 point (total wire length approx. 50m) |
| 941 | 7 point (total wire length approx. 60m) |
| 942 | Laying, Glanding and Termination for lighting circuit cables (650 / 1100V (Uo / U) voltage grade, Cu conductor (stranded / solid), XLPE insulated, armoured) from SLDB / ESLDB onwards upto the lighting fixtures / associated control gear boxes / junction boxes(applicable for all Lighting Fixtures, excluding Street Lighting Fixtures and Lighting Fixtures for Office buildings / Control rooms / Other rooms with false ceiling)Handling, shifting of cable drums from site-store / yard to the installation location, unpacking, laying of lighting circuit cables / wires in cable trays / through above ground conduits (PVC / GI) clamped on wall or structure or through floor conduits / by cleating of cables to concrete / wall / steel structrues by saddles - as per applicable construction documents and other associated work so as to ensure the completeness of installation work.Handling, shifting of cable drums from site-store / yard to the installation location, unpacking, laying of lighting circuit cables / wires in cable trays / through above ground conduits (PVC / GI) clamped on wall or structure or through floor conduits / by cleating of cables to concrete / wall / steel structrues by saddles - as per applicable construction documents and other associated work so as to ensure the completeness of installation work.Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembly and installation of cable glands (industrial / For Explosive Atmospheres type) with PVC hoods, installation of components supplied separately - as recommended by MANUFACTURER / applicable construction documents, installation of lug, termination of cable at designated location and other associated work so as to ensure the completeness of installation work.Supply of all fixing hardware such as spacer bar, saddles, UV resistant PVC cable ties, Al cable tags, PVC hoods, etc. as as per the site requirement is included in the scope.Quantity of Lighting Fixtures, associated control gear boxes / junction boxes is defined in this document under the respective headings.The quantity of total looping cable length required for the work is mentioned below. |
| 943 | 3 C X 2.5 sq.mm |
| 944 | 3 C X 4 sq.mm |
| 945 | 3 C X 6 sq.mm |
| 946 | 3 C X 10 sq.mm |
| 947 | EXHAUST FANS AND CEILING FANS |
| 948 | Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of exhaust / ceiling fans and associated accessories - as recommended by MANUFACTURER / applicable construction documents, checking of internal wiring other associated work so as to ensure the completeness of installation workTesting, precommissioning and commissioning activities are included in the scope.Minor civil work such as chipping, modifications in the wall cutout as required, grouting of frame, replastering and making area good etc.as per the site requirement (including the supply of consumable material for the same) is included in the scope. Supply of all fixing hardware as per the site requirement is included in the scope. |
| 949 | Industrial type Exhaust fans |
| 950 | 300mm dia. |
| 951 | 450mm dia. |
| 952 | 600mm dia. |
| 953 | Exhaust fans For Explosive Atmospheres |
| 954 | 300mm dia. |
| 955 | 450mm dia. |
| 956 | 600mm dia. |
| 957 | SMALL POWER |
| 958 | Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of small power equipment and associated accessories such as control switches, socket outlets, modular box, face plate etc. - as recommended by MANUFACTURER / applicable construction documents, checking of internal wiring other associated work so as to ensure the completeness of installation workTesting, precommissioning and commissioning activities are included in the scope.Minor civil work such as chipping, grouting for fixing of various equipment, replastering and making area good etc.as per the site requirement (including the supply of consumable material for the same) is included in the scope. Supply of all fixing hardware as per the site requirement is included in the scope. |
| 959 | SWITCH SOCKET OUTLETS |
| 960 | Civil work such as chipping of walls (as per the site requirement) and replastering and making area good after embedding of modular boxes for switch boxes, as per the site requirement (including the supply of consumable material for the same) is included in the scope. |
| 961 | Decorative type switch socket outlets |
| 962 | Decorative type switch socket box with 1 no. 5/15A switch socket unit and 1 no. piano type switch |
| 963 | Decorative type switch socket box with 1 no. 5/15A switch socket unit and 2 nos. piano type switches |
| 964 | Decorative type switch socket box with 1 no. 5/15A switch socket unit and 3 nos. piano type switches |
| 965 | Decorative type switch socket box with 1 no. 5/15A switch socket unit and 4 nos. piano type switches |
| 966 | Decorative type switch socket box with 1 no. 5/15A switch socket unit and 5 nos. piano type switches |
| 967 | Decorative type switch socket box with 1 no. 5/15A switch socket unit |
| 968 | Decorative type switch in single module with 1 no. 5A piano type switches |
| 969 | Decorative type switch in double module with 2 no. 5A piano type switches |
| 970 | Decorative type switch in tripple module with 3 no. 5A piano type switches |
| 971 | Decorative type switch in quad module with 4 no. 5A piano type switches |
| 972 | Decorative type switch socket switchboard with 5/15A, 5 pin, socket outlet with 15A switch and 'ON' LED indication & fuse |
| 973 | Surface / Concealed mounting type ( 2-Module) RJ 11 / RJ 45 Connectors Female type complete with Moduler box, cover plate etc. for telephones |
| 974 | Industrial type switch socket outlets (for Indoor Installation) |
| 975 | 20A, single phase switch socket outlet with 1no. 3 pin socket and 1 No. 20 A, 10 kA, SPMCB, in sheet steel enclosure |
| 976 | CONVENIENCE SWITCH SOCKET OUTLETS (Wall/column/structure/Railing mounted) |
| 977 | Installation of Industrial / Explosive Atmospheres type Switch Socket Outlets shall be as per 'Installation Details - Lighting and applicable construction documents.Supply of Installation materials (excluding structure steel) as per 'Installation Details - lighting' is included in the scope.Fabrication and installation of steel support structure as per the site requirement, is considered separately in SECTION - F. |
| 978 | Convenience sockets (single phase)Installation Type : L15A / L15B / L15C / L15D |
| 979 | 24V, 5A switch socket unit for Industrial / Explosive Atmospheres, with built-in 100VA, 220V / 24V transformer, Installation Type : L15A / L15B / L15C / L15D |
| 980 | JUNCTION BOXES (JB) AND POWER JUNCTION BOXES (PJB) FOR MOTORS / OTHER EQUIPMENT - - Industrial / Explosive Atmospheres type |
| 981 | Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of junction boxes (except lighting JB) / power junction boxes and associated accessories on wall / concrete / steel structure - as recommended by MANUFACTURER / applicable construction documents, checking of internal wiring, stenciling with paint on equipment enclosures as required and other associated work so as to ensure the completeness of installation work.Testing, precommissioning and commissioning activities are included in the scope.Supply of Installation materials (excluding structure steel) as per Installation details-Power is included in the scope.Fabrication and installation of steel support structure as per the site requirement, is considered separately in SECTION - F.Installation of Junction Boxes shall be as per 'Installation Details - Power' and applicable construction documents. |
| 982 | Weight of Unit up to 5 kg |
| 983 | Weight of Unit above 5 kg, but up to 20 kg |
| 984 | Weight of Unit above 20 kg, but up to 100 kg |
| 985 | Weight of Unit above 100 kg, but up to 200 kg |
| 986 | POWER SOCKET OUTLETS |
| 987 | Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of switch socket outlets and associated accessories such as control switches, socket outlets, junction box, front plate etc. on wall / concrete / steel structure - as recommended by MANUFACTURER / applicable construction documents, checking of internal wiring, stenciling with paint on equipment enclosures as required and other associated work so as to ensure the completeness of installation work.Testing, precommissioning and commissioning activities are included in the scope.Installation of Industrial / Explosive Atmospheres type Power socket outlets shall be as per 'Installation Details - Power' and applicable construction documents.Supply of Installation materials (excluding structure steel) as per 'Installation Details - Power' is included in the scope.Fabrication and installation of steel support structure as per the site requirement, is considered separately in SECTION - F. |
| 988 | Industrial / Explosive Power Socket Outlets |
| 989 | Installation Type : P10A/B |
| 990 | Installation Type : P15 |
| 991 | Installation Type : P17 |
| 992 | FIRE ALARM AND COMMUNICATION SYSTEMS |
| 993 | FIRE ALARM (FA) SYSTEM |
| 994 | Handling, shifting from site-store / yard to the installation location, unpacking, assembling and installation of various components in FA system and associated accessories such as manual call points, plug-in devices, bases for devices etc. on wall / concrete / steel structure - as recommended by MANUFACTURER / applicable construction documents, stenciling with paint on equipment enclosures as required andand other associated work so as to ensure the completeness of installation work.Testing and precommissioning activities, commissioning assistance as required by MANUFACTURER's supervisor is included in the scope. Minor civil work such as chipping, grouting for fixing of various equipment and replastering the same as per the site requirement (including the supply of consumable material for the same) is included in the scope. Supply of Installation materials (excluding structure steel) as per 'Installation Details - FA System' is included in the scope.Supply of all fixing hardware as per the site requirement is included in the scope.Installation shall be as per 'Installation Details - Fire Alarm System' and applicable construction documents.Fabrication and installation of steel support structure as per the site requirement, is considered separately in SECTION - F. |
| 995 | Central FA panelTAG : LATERApprox. Dimensions (LxBxH) : 600 x 600 x 2000 mmApprox. Weight : 200 kgsMounting : Wall mounted / Column mounted / On False floor supported with structural steel base frame Location : SRR (Indoor) |
| 996 | FA system accessories Industrial type / Explosive Atmospheres |
| 997 | Installation Type: FAHC1 |
| 998 | Installation Type: FAHS1 |
| 999 | Installation Type: FAHZ1 |
| 1000 | Installation Type: FASC1 |
| 1001 | Installation Type: FASC2 |
| 1002 | Installation Type: FASS1 |
| 1003 | Installation Type: FCPC1 |
| 1004 | Installation Type: FCPC2 |
| 1005 | Installation Type: FCPP1 |
| 1006 | Installation Type: FCPP2 |
| 1007 | Installation Type: FCPR1 |
| 1008 | Installation Type: FCPS1 |
| 1009 | Installation Type: FMDC1 |
| 1010 | Installation Type: FMDF1 |
| 1011 | Installation Type: FMDF2 |
| 1012 | Installation Type: FMDF3 |
| 1013 | Installation Type: FMDS1 |
| 1014 | Installation Type: FRIC1 |
| 1015 | Installation Type: FRIF1 |
| 1016 | Installation Type: FCPS2 |
| 1017 | Installation Type: CFBC1 |
| 1018 | Installation Type: CFBS1 |
| 1019 | PUBLIC ADDRESS (PA) SYSTEM |
| 1020 | Handling, shifting from site-store / yard to the installation location, unpacking, assembling and installation of various components in PA system and associated accessories such as field call stations, acoustic hoods etc. on desk / wall / concrete / steel structure - as recommended by MANUFACTURER / applicable construction documents, stenciling with paint on equipment enclosures as required and other associated work so as to ensure the completeness of installation work.Testing and precommissioning activities, commissioning assistance as required by MANUFACTURER's supervisor is included in the scope. Minor civil work such as chipping, grouting for fixing of various equipment and replastering the same as per the site requirement (including the supply of consumable material for the same) is included in the scope.Supply of Installation materials (excluding structure steel) as per 'Installation Details - Communication & PA System' is included in the scope. Supply of all fixing hardware as per the site requirement is included in the scope.Installation shall be as per 'Installation Details - Communication & PA System' and applicable construction documents.Fabrication and installation of steel support structure as per the site requirement, is considered separately in SECTION - F. |
| 1021 | Central PA panelApprox. Dimensions (LxBxH) : 800 x 800 x 2000 mmApprox. Weight : 250 kgsMounting : On False floor supported with structural steel base frame Location : SRR (Indoor) |
| 1022 | Master Control StationInstallation of Master Control Station (MCS) consisting of control key board, Loud speaker, goose-neck microphone, console mounted handset, headset and other accesories (Installation Type: CMCS1)Mounting : Desk stop |
| 1023 | PA system accessories Industrial type / Explosive Atmospheres |
| 1024 | Installation Type: CTFC1 |
| 1025 | Installation Type: CTFC2 |
| 1026 | Installation Type: CTFR1 |
| 1027 | Installation Type: CTFR2 |
| 1028 | Installation Type: CTFS2 |
| 1029 | Installation Type: CTFS3 |
| 1030 | Installation Type: CFBC1 |
| 1031 | Installation Type: CFBR1 |
| 1032 | Installation Type: CFBS1 |
| 1033 | Installation Type: CSPKC1 |
| 1034 | Installation Type: CSPKC2 |
| 1035 | Installation Type: CSPKC3 |
| 1036 | Installation Type: CSPKF1 |
| 1037 | Installation Type: CSPKP1 |
| 1038 | Installation Type: CSPKS1 |
| 1039 | Installation Type: CSPKR1 |
| 1040 | Installation Type: CMCS1 |
| 1041 | TELEPHONE SYSTEMHandling, shifting from site-store / yard to the installation location, unpacking, assembling and installation of various components in PA system and associated accessories such as field call stations, acoustic hoods etc. on desk / wall / concrete / steel structure - as recommended by MANUFACTURER / applicable construction documents, stenciling with paint on equipment enclosures as required and other associated work so as to ensure the completeness of installation work.Testing and precommissioning activities, commissioning assistance as required by MANUFACTURER's supervisor is included in the scope. Minor civil work such as chipping, grouting for fixing of various equipment and replastering the same as per the site requirement (including the supply of consumable material for the same) is included in the scope.Supply of Installation materials (excluding structure steel) as per 'Installation Details - Communication & PA System' is included in the scope. Supply of all fixing hardware as per the site requirement is included in the scope.Installation shall be as per 'Installation Details - Communication & PA System' and applicable construction documents.Fabrication and installation of steel support structure as per the site requirement, is considered separately in SECTION - F. |
| 1042 | Installation of Telephine Ststem cabinet onsists of Access switch, Media gate wat etc |
| 1043 | Installation shall be as per 'Installation Details - Communication & PA System' and applicable construction documents. |
| 1044 | Telephone ( Industrial type / Explosive Atmospheres) |
| 1045 | Installation Type: CTFC2 |
| 1046 | Installation Type: CTFS2 |
| 1047 | Installation Type: CTFZ1 |
| 1048 | Junction boxes |
| 1049 | Telephone System Junction Box / IDF with 1 nos. 20 Pair incoming cable(s) and 20 nos 1 Pair outgoing cable(s) |
| 1050 | CCTV SYSTEMHandling, shifting from site-store / yard to the installation location, unpacking, assembling and installation of various components in CCTV system and associated accessories such as cameras, JBs, plug-in devices, bases for devices etc. on wall / concrete / steel structure / Self standing - as recommended by MANUFACTURER / applicable construction documents, stencilling with paint on equipment enclosures as required and other associated work so as to ensure the completeness of installation work.Supply of all the Installation Material and Installation shall be as per 'Installation Details - Communication & PA System' and applicable construction documents and applicable construction documents, including any additional material as per site requirement so as to ensure the completeness of installation work.and as per approved drawings, specifications of this tender and directions of Engineer-in-Charge..Testing and precommissioning activities, commissioning assistance as required by MANUFACTURER's supervisor is included in the scope. Minor civil work such as chipping, grouting for fixing of various equipment and replastering the same as per the site requirement (including the supply of consumable material for the same) is included in the scope. |
| 1051 | CCTV CabinetApprox. Dimensions (LxBxH) : 800 x 800 x 2000 mmApprox. Weight : 250 kgsMounting : On False floor supported with structural steel base frame Location : SRR (Indoor) |
| 1052 | Cameras |
| 1053 | Installation of Cameras including wiper & washer system and mounting poles/ structures, with required civil foundations, supply and installations erection material etc. as applicable are included in scope |
| 1054 | Installation Type: CTVC1 |
| 1055 | Installation Type: CTVC2 |
| 1056 | Installation Type: CTVR1 |
| 1057 | Installation Type: CTVS1 |
| 1058 | EARTHING AND LIGHTNING PROTECTION |
| 1059 | Handling, shifting from site-store / yard to the installation location, unpacking, assembling and installation of earthing and lightning protection systems and accessories underground / wall / concrete / steel structure / cable trays - as recommended by MANUFACTURER / applicable construction documents and other associated work so as to ensure the completeness of installation work.Testing, precommissioning and commissioning activities are included in the scope. |
| 1060 | EARTHING |
| 1061 | Installation shall be as per 'Installation Details - Earthing' and applicable construction documents. |
| 1062 | Installation of earth conductor laid underground |
| 1063 | Installation and connection of GI earthing strip buried individually at a depth of 600 mm including welding at joints, providing anti-corrosive paint r bitumen and jute covering for welded portion, clamping and necessary hardware for connecting, excavation and refilling etc., including all labour and materials, as per approved drawings & specifications For GI earthing conductors, laying of conductor including bending, drilling, welding / jointing as required is included in the scope.For GI earthing conductors, supply and application of coal tar bituminous paint or cold galvanising paint on welded joints is included in the scope.Excavation of soil up to the required depth, installation of earth conductor (GI strip / bare copper conductor / insulated copper cable), back filling and compacting of soil and disposing the excess soil, termination as required is included in the scope |
| 1064 | 40 x 5 mm GI strip |
| 1065 | 25x 6 mm GI strip |
| 1066 | 50 x 6 mm HDGI strip |
| 1067 | 75 x 10 mm HDGI strip |
| 1068 | Installation of earth conductor laid on wall / concrete / steel structure / cable traysInstallation of earth conductor (GI strip) on wall / concrete / steel structure / cable trays by cleating at every 500mm, termination as requied.For GI earthing conductors, laying of conductor including bending, drilling, welding / jointing as required is included in the scope.For GI earthing conductors, supply and application of coal tar bituminous paint or cold galvanising paint on welded joints is included in the scope.Supply of all fixing hardware as per the site requirement is included in the scope. |
| 1069 | 50 x 6 mm HDGI strip |
| 1070 | 75 x 10 mm GI strip |
| 1071 | Installation of earth conductor to be embedded in finished concrete floorsInstallation of earth conductor (GI strip) on concrete floorsFor GI earthing conductors, laying of conductor including bending, drilling, welding / jointing as required is included in the scope.For GI earthing conductors, supply and application of coal tar bituminous paint or cold galvanising paint on welded joints is included in the scope.Civil work such as chipping / drilling of through-holes / cutouts in floor and replastering and making area good after installation of conductor as per the site requirement (including the supply of consumable material for the same) is included in the scope. |
| 1072 | 40 x 5 mm GI strip |
| 1073 | 50 x 6 mm GI strip |
| 1074 | 75 x 10 mm GI strip |
| 1075 | Installation of earthing / lightning protection electrodes |
| 1076 | Excavation of soil upto the required depth, installation and testing of earth electrode, filling of the pit with the appropriate material as required, earthing connection of earth electrode with main earth grid, back filling, compacting of soil, disposing the excess soil.Civil work including construction of concrete chamber with cover for the earth pit as per the site requirement is included in the scope. |
| 1077 | Installation Type : E01A |
| 1078 | Installation Type : E01B |
| 1079 | Installation of earth busesInstallation and testing of earth buses on wall / concrete / steel structure / cable trays.Supply of all fixing hardware as per the site requirement is included in the scope.Fabrication and installation of steel support structure as per the site requirement, is considered separately in SECTION - F. |
| 1080 | Installation Type : E02A |
| 1081 | Installation Type : E02B |
| 1082 | Installation Type : E20 |
| 1083 | Installation Type : E22 |
| 1084 | Install following Earthing Material as per Installation Type : E141. 9 DIA G.I. BAR2. SHARP JAW TONG TYPE HEAVY DUTY SPRING CLAMP-100A |
| 1085 | Installation of Pipe line Flange/ Pipe Earthing material as per Installation Standard E09/E10 (Doc. No.TK-1P22A-EL-STD-0003), .This shall include installation of 10 MM (3/8\\") DIA GI WIRE ROPE for the no. of Flange connections.The Termination scope also includes supply of lugs for GI wire rope and all hardware etc. Refer List For Pipe Line Bonding (Doc. No.TK-1P22A-EL-LST-0010 ) for details of Flange earthing |
| 1086 | LIGHTNING PROTECTION |
| 1087 | Installation shall be as per 'Installation Details - Lightning Protection' and applicable construction documents. |
| 1088 | Installation of lightning protection conductor laid on wall / concrete / steel structure / roof Installation of lightning protection conductor (GI strip) on wall / concrete / steel structure including the installation of test links and accessories, insulator supports, termination as required.For GI earthing conductors, laying of conductor including bending, drilling, welding / jointing as required is included in the scope.Supply of Installation materials (excluding structure steel) as per installation details-Earthing\\" is included in the scope.Supply of all fixing hardware as per the site requirement is included in the scope. |
| 1089 | 25 x 6 mm HDGI strip |
| 1090 | Installation of lightning protection rods / finials |
| 1091 | Installation of of lightning arrestors, including the required supporting arrangement. |
| 1092 | Supply of all fixing hardware as per the site requirement is included in the scope. |
| 1093 | Installation Type : E24 |
| 1094 | Installation Type : E25 |
| 1095 | Installation Type : E26 |
| 1096 | Installation Type : E27 |
| 1097 | STRUCTURAL STEEL |
| 1098 | Fabrication, erection (by welding / fixing by anchor fastners), surface preparation and painting of structural steel as per the applicable construction documents so as to ensure the completeness of installation work for all the electrical equipment / items mentioned in Section A to E above, and chequered plates as per the applicable construction documents.Supply of all consumables such as welding electrodes (Advani Oerlikon or equivalent), gas for cutting etc. are included in the scope.Measurement of steel quantity for installation shall be based on actual quantities installed at site without wastage allowance. Surface preparation and painting of steel shall be as per doc. TP-1ZZZA-PI-SPE-0003. (Technical Specification for Painting) |
| 1099 | Structural steel (MS) |
| 1100 | Galvanised Iron (GI) |
| 1101 | MISCELLANEOUS ITEMS |
| 1102 | CIVIL WORK |
| 1103 | Excavation |
| 1104 | Excavation in soil for the purpose of cable laying activity up to a depth of 2m (maximum) and width of trench 4m (maximum) considering all the relevant safety standards, backfilling the excavated area after cable laying activity, consolidation after backfilling and disposing the surplus earth at required location.Installation of soft sand of known resistivity, red coloured concrete tiles of appropriate voltage grade for cable protection, warning tapes, cable markers(including RFID tags) etc. (after cable laying activity is completed) is included in the scope. |
| 1105 | Soft / medium soil (Excavation & Back-filling) |
| 1106 | Miscellaneous civil work |
| 1107 | Activities indicated below are already included in 'SECTIONS - A to E' of this document. Unit rates are requested in the event that additional work is required over and above that already identified in 'SECTIONS - A to E'.The below mentioned rates shall be applicable only if specifically agreed & approved by OWNER / CONSULTANT. |
| 1108 | Chipping / drilling of through-holes / cutouts in concrete floor / beam, replastering and finishing the same |
| 1109 | Chipping / drilling of through-holes / cutouts in brick walls and replastering the same. |
| 1110 | Manual excavation of all types of soil and backfilling the excavated area, consolidation after backfilling and disposing the surplus earth at a point outside the site |
| 1111 | Laying of RCC hume pipes of dia 150mm for road crossing including excavation of road upto a depth of 1500 mm back filling and consolidating the surface. Supply of RCC hume pipes of reputed make as required, and civil work such as excavation, installation of hume pipes (including the supply of consumable material for the same), backfilling is included in the scope. |
| 1112 | filling/spreading of certified soft sand of known resistivity in the concrete trenches build by others after laying of cables, compacting the same. The scope includes removal of RCC trench covers/ slab, refixing of RCC trench Covers/Slabs after filling / spreading the sand, including all labour and materials complete as per approved drawings, specification of this tender and directions of Engineerin-in-charge |
| 1113 | Installation of approved second class bricks of 75 mm thickness in cable trenches for cable protection, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge. (Actual area of laid brick surfaces shall be measured). |
| 1114 | Installation of approved Red coloured concrete tiles in cable trenches for cable protection, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge. (Actual area of laid brick surfaces shall be measured). The scope includes supply and installation of warning tape as per Installation details |
| 1115 | Anchor fasteners |
| 1116 | Installation of heavy duty Galvanised steel anchor fasteners for supporting various equipment, in brick work / concrete workInstallation of anchor fasteners indicated below excludes those already considered in various applicable 'Installation Details' mentioned in 'SECTIONS - A to E' in this document.Installation of anchor fasteners indicated below excludes those already considered in various applicable 'Installation Details' mentioned in 'SECTIONS - A to E' in this document |
| 1117 | Anchor fasteners M8 type x 60mm |
| 1118 | Anchor fasteners M10 type x 75 mm |
| 1119 | Anchor fasteners M12 type x 100 mm |
| 1120 | SAFETY ITEMS |
| 1121 | Installation of safety items mentioned below, in all the electrical rooms / buildings / transformer yards, etc. as per applicable statutory requirements / HSE documents / as indicated in applicable construction documents. |
| 1122 | Enameled caution boards for 33 kV. |
| 1123 | Enameled caution boards for 6.6 kV. |
| 1124 | Enameled caution boards for 1.1 kV. |
| 1125 | Enameled Danger plates to be installed in electrical rooms such as transformer bay, switchgear room etc. |
| 1126 | 3 ply Lamicoid tag plates of appropriate size for various equipment, with White letters on Black background, as per the site requirement |
| 1127 | Epoxy insulating floor coating (Valency Compound Make - Valency-111 CLASS A or equivalent |
| 1128 | 33kV System |
| 1129 | 6.6 kV systems - |
| 1130 | upto 1.1 kV systems |
| 1131 | Installation of Synthetic Insulating mat (as per IS 15652: 2006). The rate shall include cutting to required size and placing the mats in front of switchgear panels as directed by Site Engineer-in-charge. The mat shall be permanently pasted on the floor. |
| 1132 | 33kV System |
| 1133 | 6.6 kV systems - |
| 1134 | upto 1.1 kV systems |
| 1135 | First aid information chart (for electrical hazards such as Shock treatment) : Framed laminated shock treatment chart, conforming to IE rules, in English and local language. Name, address and telephone number of nearest doctor shall be mentioned in it. |
| 1136 | First aid boxes along with required medicines / medical equipment, containing ointments for treatment of electrical burns, conforming to IE rules. |
| 1137 | Wall mounted, Electrical Single Line Diagrams-A0 size\\" for the unit including frame, glass, hardwares, etc. |
| 1138 | GENERAL ITEMS |
| 1139 | Installation of general items mentioned below, as required. |
| 1140 | Office tables of reputed make |
| 1141 | Office chairs of reputed make |
| 1142 | Full size Cupboard of reputed make, sheet steel enclosure (for documentation) |
| 1143 | Tool Cabinet, Wall Mounted |
| 1144 | Key Cabinet, Wall Mounted |
| 1145 | Tarpaulin (for weather protection of stored electrical equipment) |
| 1146 | Insulated step ladder of reputed make (suitable for indoor work in switchgear rooms) |
| 1147 | Installation of Fire proofing of cables up 3 m length at entry points of both endsincluding all labour and materials required. (Actual area of surface painted shall be measured) _ - (As perIEC 60331) Fire proof paint for cables for 1 hour Fire Rating (CABLE SURFACE AREA WISE)Fire retardant cable coatingHILTI : CP679A / OBO BETTERMAN equivalent product |
| 1148 | Installation of Fire Stop (Fire sealing) material suitable to withstand for 240 min including all labour and materials required for sealing the wall / Floor opening / conduits fire sealings. Refer annex EW4-6 for details of openings to be sealed |
| 1149 | Installation of Fire Stop (Fire sealing) material suitable to withstand for 90 min including all labour and materials required for sealing the wall / Floor opening / conduits fire sealings. Refer annex EW4-6 for details of openings to be sealed |
| 1150 | Installation of Weather proofing material HILTI make including all labour and materials required for sealing the wall opening / conduits fire sealings. |
| 1151 | ELECTRICAL STATUTORY APPROVAL |
| 1152 | Obtaining approval on applicalbe Released for Construction (RFC) / Final drawings, commencement certificate from concerned authorities, approval of installations, liasoning with electrial inspector, organising inspector visits to site ( up to 3 visits) as required as per applicable statutory norms, etc. and all the associated work |
| 1153 | MANPOWER SUPPLY RATES PER DAY |
| 1154 | The below mentioned rates for Manpower Supply shall be applicable only for work performed over and above the electrical works already defined as forming part of CONTRACTOR’s scope in the Tender Document / Contract.Note: These rates for man power are applicable only after total completion of Electrical Installation & Commissioning activities. This shall also include the Implementation of LOTO system during precommissioning & commissioning stage . The below mentioned rates shall be applicable only if specifically agreed & approved by OWNER / CONSULTANT. Please Enable Macros to View BoQ information |
| 1155 | The below mentioned rates for Manpower Supply shall be applicable only for work performed over and above the electrical works already defined as forming part of CONTRACTOR’s scope in the Tender Document / Contract.Note: These rates for man power are applicable only after total completion of Electrical Installation & Commissioning activities. This shall also include the Implementation of LOTO system during precommissioning & commissioning stage . The below mentioned rates shall be applicable only if specifically agreed & approved by OWNER / CONSULTANT. Please Enable Macros to View BoQ information |