|
| 1 | Taking down Cement Plaster of any description on brick or stone walls or concrete surfaces including raking out joints, hacking for key etc., complete all as specified and as directed. |
| 2 | M&L for rendering 10mm thick plaster in CM (1:6) on brick/block or concrete surfaces finished even & smooth etc., complete all as specified and as directed. |
| 3 | M&L for rendering 15mm thick plaster in CM (1:4) over a concrete or block masonry surfaces including mixing water proofing compound on top layer as per manufactures instructions (or 3% by weight of cement) and finishing the top surfaces even and fair etc., complete all as specified and as directed. Note :Water proofing compound shall be measured and paid seperately under relevant item of this schedule as supply only. |
| 4 | Supply only Liquid water proofing compound ISI marked etc., complete all as specified and as directed. Note : WPC may apply as per manufactures instructions or 3% by the wt of cement. |
| 5 | M&L preparing newly plastered surfaces of wall and applying two coats of high sheen, Anti-Fungal, Excellent Stain Resistant interior Acrylic emulsion paint over a coat of primer complete all as specified and as directed by Engineer-in-charge.Make: Asian Paints (Tractor uno), Berger (Bison Emulsion) Nerolac (beauty smooth). Shalimar Paints (No.1 Silk) |
| 6 | M & L for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal esistance, dirt resistance exterior paint of WHITE colour with silicon additives coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm over new surfaces complete all as specified and as directed by Engineer-in-charge.Make: Asian Paints (Apax Ultima), Berger (Weathercoat Long Life Flexo) Nerolac (Excel Total). Shalimar Paints (Weatherpro+ Super Luxury Emulsion) |
| 7 | Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) etc., complete all as specified and as directed. |
| 8 | M&L for 75mm thick PCC 1:3:6 Type C-2 (using 40mm crushed stone aggregate) as in plinth protection finished even and fair without using extra cement etc., complete all as specified and as directed. |
| 9 | Demolition of precast concrete work built in cement mortar including all quoins arches pillars etc., complete all as specified and as directed. |
| 10 | M&L for Pre-cast cement concrete block masonry Type C1 1:3:6 (20mm graded aggregate) with solid blocks, exc.10 cm in width and setting in cement mortar 1:6, etc., complete all as specified and as directed. |
| 11 | M&L for precast cement concrete block masonry with solid Type C1 1:3:6 (20mm graded aggregate as per IS 383) of 10 cm in width and setting in CM 1:6 all as specified. |
| 12 | Dismantling floor, hearth or wall tiles including cement mortar bedding (but not backing) and removing serviceable tiles to stores and rubbish off the premises etc., complete all as specified and as directed. |
| 13 | M&L for Double charged/ultracharged Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15mm thick screed bed in CM (1:6) etc., complete all as specified and as directed. |
| 14 | -Ditto all as per item No 13 here-in-before but in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile over 10mm thick backing in cement mortar (1:3) etc., complete all as specified and as directed. |
| 15 | M&L for coloured non-skid ceramic tiles 7 to 8 mm thick exceeding 0.11 sqm but not exceeding 0.18 sqm area of each tiles in floor/ steps etc set and jointed in neat cement slurry and pointed in coloured cement to match as in floor over and including 15mm thick screed bed in CM (1:6) etc., complete all as specified and as directed. |
| 16 | M&L for glazed ceramic coloured/printed tiles 450x350x 7mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile over 10mm thick backing in cement mortar (1:3) etc., complete all as specified and as directed. |
| 17 | Dismantling of stone slabs and tiles of any description or thickness in floors, approns and laid bedded and pointed in any mortar etc., complete all as specified and as directed. |
| 18 | M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screed bed in CM (1:6) etc., complete all as specified and as directed. |
| 19 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations all as specified. |
| 20 | Taking down chowkats or frames(without taking off shutters from the frame) area exc 1.5 Sqm but n.exc 4.0 Sqm each.(including Aluminium windows/ventilators etc) |
| 21 | Taking down chowkats or frames(without taking off shutters from the frame) area n.exc 1.5 Sqm each.(including Aluminium windows /ventilators etc) |
| 22 | Providing and fixing factory made uPVC any colour Sliding window Three track area not exceeding 2.00 sqm each made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories.Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose. gap and grooves should be filled with silicon agent. |
| 23 | Providing and fixing factory made uPVC any colour fixed window made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glassNote:- Gap and grooves should be filled with silicon agent |
| 24 | S&F of 6mm thick sheet figured glass pin headed type, not exc 0.50 sqm in each pane, duly fixed with oil putty or wooden bidding as required, complete all as directed. |
| 25 | Supply and fixing factory made uPVC any colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws,etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in Charge. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 26 | S&F for Mild Steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 27 | M&L for preparing new steel or iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer etc., on truss work & new pressed steel framecomplete all as specified and as directed. |
| 28 | S&F for factory made single extruded 18/19 mm thick WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws etc., complete all as specified and as directed.NOTE:- All joint should be filled with sealant |
| 29 | S&F for 150 mm long Brass handles, cast type, polished bright etc., complete all as specified and as directed. |
| 30 | S&F for 100 mm size hasp and stable, safety type , brass with mild steel hinges pin including bolt to hinge plate with scrows etc., complete all as specified and as directed. |
| 31 | S&F for Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed etc., complete all as specified and as directed. |
| 32 | Dismantling Asbestos Cement Corrugated or Semicorrugate in Roof covering, complete all as specified and directed. |
| 33 | S&F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.(Note : Height of the bldg up to G+3 storey including necessary safety arrangements) etc., complete all as specified and as directed. |
| 34 | S&F for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridges, hips, valley gutter, drip, and straight flashing all as specified and as directed.(Note : Height of the bldg up to G+3 storey including necessary safety arrangements) etc., complete all as specified and as directed. |
| 35 | S&F Aluminium flat iron work in wind ties 40x6mm size fixed with 50mm/ 75 mm aluminium self staging screws with integral EPDM washer screwed in roof covering all as directed.(Note :- Height of the bldg up to 15 mtrs including necessary safety arrangements) etc., complete all as specified and as directed. |
| 36 | Dismantling wrought iron or mild steel work of any description not otherwise provided for |
| 37 | M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.conforming to Fe.290.Gde-E-165 etc., complete all as specified and as directed. |
| 38 | M&L for MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment confirming to Fe 410 -W (Gde- E- 250) quality- A etc., complete all as specified and as directed. |
| 39 | S&F Mild steel screw bolts (machine made) 5 to 10 mm dia with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n.exc. 10 cm long etc., complete all as specified and as directed. |
| 40 | S&F in repairs 5 mm thick frameless Looking Mirror of size as per site requirement beveled edge incl NR itching and mirror button, complete all as specified and directed. |
| 41 | Dismantling of wall / ceiling boards (fiber, pulp, insulation etc) / insulation boards /slabs/blankets of any thickness including cover fillets ridges etc, complete all as specified and directed. |
| 42 | Providing & fixing false ceiling with semi perforated 12mm thick micro tegular edged GRG false ceiling tiles at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1 OOOmm length and L shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in Charge. |
| 43 | Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness ( below or above ground level) etc., complete all as specified and as directed. |
| 44 | M&L for 75mm thick Cement concrete type D2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing finishing the surface even & smoth without using extra cement complete all as directed. (to receive chequered tile ) |
| 45 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete. |
| 46 | M&L for 75mm thick PCC 1:3:6 Type C-2 (using 40mm crushed stone aggregate) as in plinth protection finished even and fair without using extra cement etc., complete all as specified and as directed. |
| 47 | M&L Providing and laying vitrified parking tiles of sizes (600X600) of 10-15 mm thickness conforming to IS 15622 in all colors and shades in outdoor floors and skirting meant for parking of cars and trucks,set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 20mm thick screed bed in CM (1:4) etc., complete all as specified and as directed. |
| 48 | S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 49 | S&F Factory made single 30 mm thick extruded WPC (Wood Polymer Composite) solid moulded flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws etc., complete all as specified and as directed. (Note: stainless steel butt hinges and necessary S S screws incl in this item) |
| 50 | S&F for 125 mm long Butt hinges, extruded brass, with mild steel hinge pin, bright polished and fixed, type B-11 etc., complete all as specified and as directed. |
| 51 | S&F for 150mm aluminium anodised barrel tower bolts of extruded section and fixed etc., complete all as specified and as directed. |
| 52 | S&F for 300mm aluminium alloy anodised sliding bolts with hasp, staple and fixing clips of sheet, cast or extruded section fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed etc., complete all as specified and as directed. |
| 53 | S&F for 150mm aluminium handles, cast type , anodised etc., complete all as specified and as directed. |
| 54 | S&F in repair stainless steel curtain rod 25mm dia steel pipe cutting into length as required at site with and incl SS end caps/lobs and SS wall mounting brackets etc., complete all as specified and as directed. |
| 55 | Taking down 20mm Steel / CPVC tubing and connections including cleaning for refixing or removal to store etc., complete all as specified and as directed. |
| 56 | Taking down 25/32mm Steel / CPVC tubing and connections including cleaning for refixing or removal to store etc., complete all as specified and as directed. |
| 57 | Supply and laying of CPVC pipes 20 mm dia outer bore SDR 11 &plain CPVC SDR 11 fittings (Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor etc) on walls /ceilings or laying in floors etc., complete all as specified and as directed. |
| 58 | Supply and laying of CPVC pipes 25 mm dia outer bore SDR 11 &plain CPVC SDR 11 fittings (Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor etc) on walls /ceilings or laying in floors complete all as specified. |
| 59 | Taking down eaves gutter and rain / waste water pipes including all fittings any size and pattern etc., complete all as specified and as directed. |
| 60 | S&F for 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in treanches incuding necessary clamps etc to fixing as required etc., complete all as specified and as directed. |
| 61 | S&F in repair for 110 mm bore PVC (SWR) bends of any radius with access door etc., complete all as specified and as directed. |
| 62 | S&F in repair for 110 mm bore PVC (SWR) branch piece,single (single Y) equal or unequal with access door etc., complete all as specified and as directed. |
| 63 | S&F in repair for 110 mm bore PVC (SWR) branch piece,double (double Y) equal or unequal with access door etc., complete all as specified and as directed. |
| 64 | S&F in repair for 110mm bore PVC (SWR) junction single, (single T) equal or unequal with access door etc., complete all as specified and as directed. |
| 65 | S&F in repair for 110 mm bore PVC (SWR) junction double, (double T) equal or unequal with access door etc., complete all as specified and as directed. |
| 66 | S&F in repair for 110 mm bore PVC (SWR) couplers etc., complete all as specified and as directed. |
| 67 | S&F in repair for 110 mm bore PVC (SWR) vent cowl fixed on top etc., complete all as specified and as directed. |
| 68 | S&F for 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in treanches incuding necessary clamps etc to fixing on walls as required etc., complete all as specified and as directed. |
| 69 | S&F in repair for 75 mm bore PVC (SWR) bends of any radius with access door etc., complete all as specified and as directed. |
| 70 | S&F in repair for 75 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal with access door etc., complete all as specified and as directed. |
| 71 | S&F in repair for 75 mm bore PVC (SWR) branch piece,double (double Y) equal or unequal with access door etc., complete all as specified and as directed. |
| 72 | S&F in repair for 75 mm bore PVC (SWR) junction single, (single T) equal or unequal with access door etc., complete all as specified and as directed. |
| 73 | S&F in repair for 75 mm bore PVC (SWR) junction double, (double T) equal or unequal with accessa door etc., complete all as specified and as directed. |
| 74 | S&F in repair for 75 mm bore PVC (SWR) couplers etc., complete all as specified and as directed. |
| 75 | S&F in repair for 75 mm bore PVC (SWR) vent cowl fixed on top etc., complete all as specified and as directed. |
| 76 | M&L in repair for PVC (SWR) floor traps 75mm bore with stainless steel grating (measured seperately) including jointing to waste pipe and in cement concrete 1:2:4 type B-1 etc., complete all as specified and as directed. |
| 77 | S&F in repair for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement etc., complete all as specified and as directed. |
| 78 | S&F in repair Vitreous China urinals, all as per Parryware cat part no C8681 or equivalent complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern or spreader with brackets, flush pipe etc complete all as spd and directed by Engineer-In-Charge. |
| 79 | S&F in replacement ceramic One Piece Water Closet including soft self closing seat cover and all necessary fittings of suitable size all as per Hindware cat part No 20107 (P-18/S-22) or equivalent as approved complete all as spd and directed by Engineer-In-Charge. |
| 80 | S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position etc., complete all as spd and directed by Engineer-In-Charge. |
| 81 | S&F in repair Vitreous China Table top wash hand basin of suitable size incl complete necessary fittings excluding taps all as per Hindware cat part no 91088 model PEARL of Italian collection. or equivalent as approved excluding taps complete all as specified and directed., Hindware (Ist Quality). |
| 82 | S&F in replacement of pillar mixer taps, 15 mm dia, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, complete all specified and directed. Make: Jaquar, Prayag, Parry ware (super fine). |
| 83 | S&F in replacement of bottle trap 32 mm sizewith 250 mm long wall connection pipe and wall flange made of cast copper alloy, chromium plated fancy type, complete all as directed. Make : Hindware/ Cera/ Parryware. |
| 84 | S&F in repair CP Towel Ring fixed with and including Chromium plated brass screws and wall plugs (Minimum weight 90gms) etc., complete all as specified and as directed. |
| 85 | S&F in replacement of towel rack 600 mm long with lower hangers and bracket made of cast copper alloy, chromium plated, complete all as specified and directed. Make : Jaquar/Prayag/ Parryware. |
| 86 | S&F in repair Angular stop cock cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for pipe or union fixed for 15mm bore etc., complete all as specified and as directed.Make: Jaquar/Prayag/ Parryware. |
| 87 | S&F in repair to Bib Taps, cast copper alloy heavy duty, 15 mm dia, Chromium Plated, long body Fancy Type screwed down for iron pipe and fixed etc., complete all as specified and as directed.Make: Jaquar/Prayag/ Parryware. |
| 88 | S&F in repair two way bib tap cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for pipe or union fixed for 15mm bore etc., complete all as specified and as directed.Make: Jaquar/Prayag/ Parryware. |
| 89 | S&F in repair 125 mm dia CP grating incl joints with solvent cement etc., complete all as specified and as directed. |
| 90 | S & F in repair Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge complete all as specified and as directed. |
| 91 | S & F in repair powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 92 | S & F in repair Anodised aluminium powder coated grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin- charge. |
| 93 | Supply only sheet glass, 4.8 mm ordinary quality and glazing with oil putty in square in n.exc 0.5 sq.m in each pane complete all as specified and as directed |
| 94 | Supply only 5.0 mm thick Figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sq.m in each pane complete all as specified and as directed |
| 95 | Supply only aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and as directed |
| 96 | Supply only particle board, 12 mm thick medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work complete all as specified and as directed. |
| 97 | S & F 100 mm size, butt hinges, stainless steel extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and as directed. |
| 98 | S & F floor door stopper 140mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed. |
| 99 | Demolition of existing water proofing treatment by brushing with wire brush, cleaning of terracing by taking down , existing plaster etc, cleaning of all foreign material such as fungus mass dust etc, roughing surface of corner to roof by wire brush etc., complete all as specified and as directed. |
| 100 | M&L for 40mm thick plain cement concrete type B-1 1:2:4 (nominal mix) using 20mm graded stone aggregate for correction of roof slab / roof padding making necessary slope etc., complete all as specified and as directed. |
| 101 | M&L for 10mm thick rendering/screed on terrace or concrete surfaces in cement mortar 1:4 finished even and fair and apply WPC (WPC @3% by wt of cement measured and paid seperately) etc., complete all as specified and as directed. |
| 102 | M&L for laying APP modified water proofing treatment over existing RCC roof slab with following specification including brushing off the surface to receive the treatment obtain the required surface :- (a) Applying bituminous primer @ 1.2 kg/Sqm on the prepared dry roof surface.(b) Laying min 3mm thick APP membrane Plain finish weight not less than 3 to 4 kg per sqm by torch application with minimum 10cm side lap and 15cm end lap.(c) Applying two coat of aluminium paint incl preparartion of surface.Note : Laying of APP membrane shall be got done through an authorized applicator of manufacturer. |
| 103 | Providing & fixing in replacement of factory manufactured hollow PVC wall panels of approved shade, 6 mm 10 mm thick, 200-300 mm wide, and in lengths as per required, having interlocking tongue-and-groove edges, fixed over a dry and smooth surface using recommended adhesive/mechanical fixings, complete with all necessary PVC edge trims, internal/external corner profiles, joint strips, and end caps. panels shall be 100% waterproof, termite-proof, fire retardant( class B1 or Equivalent), and UV resistant( if exposed). work to include surface preparation, cutting, fitting around openings, and final cleaning, all complete as per manufacturer's specifications and directed by Engineer-In-Charge. |
| 104 | S & F 4mm thick ACP (aluminium composite panel) sheet with 0.55mm thick skins in cladding of cloumns/posts/walls, ceiling, roof etc., fixed to Aluminium frame complete and colour red/grey/blue all as directed by Engr-in-Charge. Please Enable Macros to View BoQ information |
