|
| 1 | Dismantling floor hearth or wall tiling and stone slabs including cement mortar bedding ( but not backing ) removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed |
| 2 | Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) removing rubbish off the premises etc complete all as specified and directed |
| 3 | Demolition of concrete (reinforced) of any description Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work, removing rubbish off the premises etc complete all as specified and directed. |
| 4 | Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exceeding 1.50 Sqm each, complete all as specified and directed. |
| 5 | Taking down chowkhats or frame with shutters (without taking off shutters from frames) exceeding 1.5 sqmtr but not exceeding 4 sq m each, complete all as specified and directed. |
| 6 | Taking down steel windows of any description and size and removing from site complete all as specified and as directed. |
| 7 | Demolition of brickwork built in cement mortar and removing rubbish off the premises etc complete all as specified and directed |
| 8 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 9 | Taking down cement plaster or lime plaster on walls /ceiling of any description from concrete or brick wall etc including raking out joints, hacking for key, scrubbing down with water and disposing off the retrieved debris as directed including necessary scaffoldings etc complete all as specified and directed |
| 10 | Taking up or down 15 mm bore steel water tubing and connections complete all as specified. |
| 11 | Taking up or down 20 mm bore steel water tubing and connections complete all as specified. |
| 12 | Taking up or down 25 mm bore steel water tubing and connections complete all as specified. |
| 13 | Excavating in trenches not exc 1.5m wide and n.exc 1.5 m in depth, for foundations, etc, or for shafts, wells, cesspits, manholes, pier holes, etc and not exceeding 10 square meter on plan for manholes etc and not exceeding 1.5m in depth and getting out in soft/loose soil complete all as specified and directed. |
| 14 | Returning filling in with approved excavated soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed. |
| 15 | Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level nexc. 1.5 metre above the starting point complete all as specified and directed. |
| 16 | Materials and Labour for broken stone or boulder hardcore of gauge n exe 63mm deposited, spread and levelled in layers n exe 15cm thick, watered and rammed to a true surface. |
| 17 | Materials and Labour for Sand filling under floors or in foundation including watering and consolidation complete all as specified and as directed. |
| 18 | Materials and Labour for plain cement concrete (1:4:8) type D-2, using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed. |
| 19 | Materials and Labour for formwork to faces of sides and soffits of floor or roof beams, cantilevers, lintels, shelves including supports, overhangs, etc for rough finished flat surfaces of concrete complete all as specified and directed |
| 20 | Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc; basement slabs under reamed pillars and mass concrete complete including necessary formwork all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately) |
| 21 | Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels complete complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately) |
| 22 | Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in slabs and shelves supported on walls, beams and columns in floors, roofs and landings etc, any thickness complete complete including necessary formwork all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately) |
| 23 | Materials and Labour for precast cement concrete louvers and jallies,(1:2:4) type B0 using 12.5 mm graded stone aggregate, 40mm thick (measured solid), including all mouldings, Set in cement mortar (1:4) complete all as specified and directed. |
| 24 | Materials and Labour for TMT bars 10 mm dia and over, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed. |
| 25 | Materials and Labour for TMT bars 6 to 10 mm dia in stirrups, spacers and binders, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed. |
| 26 | Materials and Labour for rolled mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.conforming to Fe 410-W (Gde-E- 250) quality-A/Fe.290.Gde-E-165 including painted one shop coat of zinc chromate primer paint (including preparation ofsurface) at workshop before fabrication complete all as specified and as directed. |
| 27 | Supply & fixing wire netting of galvanised steel wire 1.40mm dia, size of mesh 20 mm, fixed with tinned tacks of wire staples complete all as specified. |
| 28 | Supply and fixing Pre-painted galvalume aluminum zinc coating (AZ-150) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed. |
| 29 | Materials and labour for preparing of new steel surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed. |
| 30 | Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement mortar (1:6) for laying of floor finishes complete all as specified and directed. |
| 31 | Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) for laying of floor finishes complete all as specified and directed. |
| 32 | Materials and labour for coloured 450x300x7-8 mm thick glazed ceramic tiles on vertical surfaces such as skirting,dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick backing coat in cement mortar (1:4) , complete all as specified and directed. |
| 33 | Materials and labour for 20mm thick granite slabs of any type (table rubbed and polished) on cooking platforms, slabs, floor and like, set and jointed in net cement slurry and pointed in white cement (1:2) using marble dust with admixture of pigment to match shade of granite including necessary moulding at edges laid over and including 20mm thick cement mortor screed bed in cement mortor (1:6) complete all as specified and directed. |
| 34 | Materials and labour for 20mm thick granite slabs of any type (table rubbed and polished) on riser of steps,skirting,dado, pillar and like, set and jointed in net cement slurry and pointed in white cement (1:2) using marble dust with admixture of pigment to match shade of granite including necessary moulding at edges laid over and including 10mm thick cement mortor (1:3) complete all as specified and directed. |
| 35 | Materials and labour for Kota stone slab 20-25mm thick in riser of steps,skirting,dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 10mm thick backing coat in cement mortar (1:3) including rubbing and polishing complete. |
| 36 | Materials and labour for Kota stone slab 20-25mm thick in floor laid over and including 20mm thick screed bed or bedding layer of cement mortar (1:6)and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. |
| 37 | Materials and labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded stone aggregate as in floors, plinth protection, path etc. finished the surface of concrete even and smooth smooth without using extra cement, complete all as specified and directed. |
| 38 | Materials and labour for 75 mm thick plain cement concrete (1:4:8) type D2 using 40 mm graded stone aggregate as in sub-base of floors, plinth protection etc. finished the surface of concrete fair and even, complete all as specified and directed. |
| 39 | Materials and labour for brick work with fly ash bricks, old/ traditional size, straight or curved on plan exc. 6mtr mean radius, built in cement mortar 1:6, complete all as specified and directed. |
| 40 | Cutting chases, pinning in brick wall making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concrete water tubing or concrete conduit wiring etc and making good, cutting not exc 10cm girth complete all as specified and as directed. |
| 41 | Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing, complete all as specified and directed. |
| 42 | Supply and fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed. Please Enable Macros to View BoQ information |
| 43 | Supply and fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed. Please Enable Macros to View BoQ information |
