|
| 1 | Taking down cement plaster including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed. |
| 2 | M&L for 10mm thick rendering in CM 1:6 over brick / concrete wall surfaces trowelled to even & smooth without using extra cement for internal wall surfaces complete all as specified and directed. |
| 3 | M&L for rendering 15 mm thick in CM 1:4 on stone/brick/concrete masonry surfaces with using integral water proofing compound finished even and smooth without using extra cement upto three storeys complete all as specified and directed. |
| 4 | M&L Rendering 10 mm thick cement plaster on ceiling surfaces in CM (1:3) complete all as specified and directed. |
| 5 | Chipping of loose/ damaged /cracked / previously repaired / delaminated or weak concrete by chieseling to expose the sound core concrete where ever required and to expose rusted reinforcement upto depth n.exc 50mm and disposal of rubbish off the premises to a distance not exc 50 mtrs including cleaning of reinforced concrete surface by air compressor complete all as specified and directed. |
| 6 | Providing and applying of 10mm thick hand applied Sika Monotop 122F single component, dual srinkage compensated thixotropic high strength formulation trawlable mortar on the brick wall including pointing of brick joint over a bond coat of sika latex (1:4:6) water cement and sika latex consumption @ 100 gm/sqm on the wall surfaces. the PMM should have compressive strength > 45 MPa in 28 days as per ASTM C 109 (7 cm cube) complete all as specified and as directed. |
| 7 | Preparing the plaster of thickness up to 15mm over the brick masonry surface by providing and applying a bond coat of Sika Latex: Water: Cement - 1:4:6 with Sika Raintite-i consumption @100gm/sqm on the wall surface followed by hand mix of cementitious mortar 1:4 to be mixed with permeability reducing polymer Sika Raintite-i @ 400gm/sqm (6%) by weight of cementitious content at time of mixing with water as per manufacturer's recommendations including all lead life, levelling the surface, curing etc complete all as specified and directed. |
| 8 | M&L for providing and fixing 12-16 mm dia injection ports non returnable nozzle by drilling, cleaning and sealing holes 50-75mm deep with fast setting high epoxy putty , solvent free , three component compound based on epoxy resins, graded fillers, and thixotropic agents as approved by GE as in beams, columns, slab and parapets as per the technical specifications and manufacturer's instructions complete all as specified and directed. |
| 9 | Supply and apply of 3 parts, very low viscous elastic polyacrylic injection resin Sika @ Injection 306 with a versatile and adjustable reaction time having mixed viscosity: 3-11 M pa s at + 20 degree C, reaction time: adjustable according to ambient temperature and execution requirement between 8-50 Mins PH - 9-10. Tested as per wissbau No 2002- 094- (1A) function test with re- injectable hose system. The holes should be drilled until a depth of approx. 5 cm (for a 6cm thick wall) before the end of the wall is reached. Pump Sika @ injection- 306@ at > 20 bar into a behind fissures or into masonry joint which are allowing water to infiltrate into unwanted area if voids is masonry being injected contain insufficient moisture to activate the grout inject a small amount of water prior to injecting the grout when movement stop or Sika @ injection - 306 appears at the next packer move to the next packer and inject. If the dampness is heavy inject similarly at next joint line complete all as specified and directed.Note: contractor will submit the warranty certificate of efflorescence for 10 years from date of completion of work. |
| 10 | Making the grooves 10mmx10mm above coating area and fill with SIKAFLEX 127, single component, elastic, moisture curing, hybrid polyurethane based construction sealent and adhesive complete all as specified and as directed.Note: contractor will submit the warranty certificate of efflorescence for 03 years from date of completion of work |
| 11 | M&L for providing by mixing and trowel application of prepacked, light weight, two component structural grade polymer modified fibre reinforced thixotropic cement mortar Sika Monotop 122F of Sika or equivalent make in Fosroc / Thermax as approved by GE at an average thickness 15 mm to the prepared concrete substrate in columns, parapets, walls fins and facias at any height, including finishing of applied Polymer mortar as per the technical specifications and manufacturer's instructions complete all as specified and directed. |
| 12 | M&L for complete removal of existing treatment of old surfaces of walls by mechanical sander with internal dust extraction system complete all as specified and directed. |
| 13 | M&L for preparation of existing/new plastered surfaces/brick surfaces by using mechanical grinder including washing down removing loose spalt/dust etc by applying one coat of exterior grade damp proof primer followed by one coat of acrylic wall care putty not less than 2 mm and applying two coats of exterior emulsion paint complete all as specified and as directed.Note: (i) Make of primer:- Asian, Berger, Nerolac(ii) Make of Exterior Emulsion Paint:- (a) Asian- Apex Ultima, (b) Berger- Weather Coat (c) Nerolac- Excel Total (iii) The complete work should be carried out through with the help of Mechanical Paint mixer and Spray Painting(iv) All windows/glasses/ventilators or other similar items should be covered properly by polythene/paper etc before spraying. |
| 14 | M&L for preparation of old plastered/new plastered or unplastered surface of walls and applying wall care putty, not less than 2mm thick and smoothening the surface with sand papers and applying two coat of OBD over one coat of acrylic primer complete all as specified and directed. |
| 15 | M&L for preparing new plastered or unplastered surfaces and applying three coats of white wash on walls complete all as specified and directed. |
| 16 | M&L for preparation of old plastered or unplastered surfaces of ceiling / soffit and applying one coats of white wash on walls complete all as specified and directed. |
| 17 | M&L preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 18 | Dismantling floor hearth or wall tiling including cement mortar bedding complete all as specified and directed. |
| 19 | M&L for 25mm thick (1:2:4) Type-B-0 (using 12.5mm graded crushed stone aggregate) as in sub base of flooring complete all as specified and directed. |
| 20 | M&L Non skid ceramic coloured tiles 8 to 9 mm thick area of each tile 600mm x 600mm , in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 15mm thick screed bed in CM 1:4 including dismantling of old tiles complete all as specified and directed. |
| 21 | M&L for coloured glazed ceramic tiles of size 300 x 600x 7 mm thick as in vertical surface set and jointed in neat cement slurry with 3-5 mm tiling Spacer tool and pointed flush with white or coloured Epoxy to match ,over and including 10mm thick baking coat in CM 1:3 complete all as specified and directed. |
| 22 | M&L for coloured vitrified tiles 10mm thick (square/rectangular) of size 600mm x 1200 mm in floors etc set & jointed with 3-5 mm tiling Spacer tool in neat cement slurry and flush pointed with white or coloured Epoxy to match, including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed. |
| 23 | M&L for coloured vitrified tiles 10mm thick (square/rectangular) of size 600mm x 1200 mm as in vertical surfaces etc set & jointed with 3-5 mm tiling Spacer tool in neat cement slurry and flush pointed with white or coloured Epoxy to match, including 15mm thick screed bed in cement mortar 1:3 complete all as specified and directed. |
| 24 | M&L for 18 to 20 mm thick machine cut Kota stone flooring over cement screed base laid and jointed with grey cement slurrry mixed with pigments to match the shade of the slab including rubbing and polishing complete all as specified over and including 20mm thick screed bed in CM 1:3 including dismantling of existing stone complete all as specified and directed. |
| 25 | Description all as per item 24.00 above but Kota stone slab (100/150mm) and 18-20 mm thick in riser of steps, skirting, dados and pillar laid over and including 10mm thick rendering to receive the stone in cement mortar and polishing complete all as 1:3 including dismantling of existing stone and jointed complete all as specified and directed.Note: Single piece Kota Stone to be used in staircase riser and tread as directed by Engr-in-charge. |
| 26 | M&L 15-18 mm Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window -cills, cooking plateforms and like in cement mortar (1:4) including pointig in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including provision of screed bed 20mm thick in CM 1 :4 including dismantling of existing stone complete all as specified and directed. |
| 27 | Rounding to edges of stone edges such as in steps/ cooking platform and other similar situations complete all as specified and directed. |
| 28 | Taking down chowkats or frame with shutter, without taking off shutter from the frames area exc 1.5 sqm but not exc 4sqm each complete all as specified and directed. |
| 29 | Taking down chowkats or frame without taking off shutters(with or without glazing and ventilator) not exc 1.5 Sqm each complete all as specified and directed. |
| 30 | S&F pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including PCC 1:3:6 type c-1 (using 20 mm graded aggregate) as in filling of chowkhats making good the disturbed area at no extra cost complete all as specified and directed. |
| 31 | S&F pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs , hinges, lock strike plate etc including PCC 1:3:6 type c-1 ( using 20 mm graded stone aggregate) as in filling of chowkhats making good the disturbed area at no extra cost complete all as specified and directed.B56 |
| 32 | S&F flush shutter 35 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 33 | S&F 35 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepare to receive glass, gauge etc (with sash bars) edges but divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers as specified in SSR Part-I Section 8 Clause 8.24(a), fitted to chowkats complete all as specified and directed.Note: There should be one vertical strip and one horizontal strip which needs to be provided to support the wire mesh in the middle of the shutter. |
| 34 | Providing and fixing factory made 100% solid WPC (wood polymer composite)- door frame of size 50mmx75mm made from wood polymer composite (single extruded process) material comprising of virgin PVC polymer of K value 57-60(suspensive Grade), calcium carbonate and natural fibers (wood powder/rice Husk/wheat husk) and non toxic additivies fabricated with meter joints after applying PVC solvent cement & screwed with full body threaded star headed screws having minium frame density of 780Kg/cbm manufacture by and ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawel strength of (Min 990N/mm, minimum compressive strength of 58N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof & fire retardent & fixed in position with SS draft fasteners/hold fast of required dia and length for external uses complete all as specified and directed. |
| 35 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed.Note: stainless steel butt hinges and necessary S S screws shall be paid separately. |
| 36 | S&F for Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 37 | S&F 200mm size aluminium anodised, barrel tower bolt of extruded section complete all as specified and directed. |
| 38 | S&F extruded aluminium alloy handles 150 mm long D type fabricated type anodised complete all as specified and directed. |
| 39 | S&F 250 mm long aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. |
| 40 | S&F Floor door stopper of aluminium alloy body 50 mm long with rubber shoes complete all as specified and directed. |
| 41 | S&F 200mm long Mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed. |
| 42 | Providing and fixing factory made UPVC white colour Three track sliding 116x52mm, (2/4 shutter) glass and wire mesh shutter windows, made of reinforcement frame 60mm x 22 mm, sliding glass window sash 78mmx60mm, reinforcement sash 30mmx18 mm, sliding mesh sash 78mmx50mm, reinforcement mesh sash 26mmx10mm, sliding interlock for window and sliding glazing bead 24.5 mm x 16mm, one panel (position as directed by Engr in cahrge) will be fixed and diveded in two portion fixed with 4mm thick plain clear glaas , mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc, making arrangement for fixing of hardware EPDM gasket 1.2 ± 0.2 mm thick, galvanised steel frame(28mm x 21.5mm), T profile (27mm x 17mm) to be inserted in required profile. Frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware Handle to slide shutter , sliding locking system and 4 mm thick glazing with selected quality glass and stain less steel wire mesh of gauge 0.56 nominal dia of wire and average width of aperture 1.18mm, complete to fix in all respect. Note:- The window shall be dIvided vertically in two part, two third of the window shall be sliding window in three track sliding channel and remaining one third part shall be devided in two part horizontally, the upper one panel shall be with 4mm thick fixed plain clear glass and lower panel with one openable shutter fixed with 4 mm thick plain clear gass as opening to \\" window AC\\". The unit rate quoted by contractor includes both glass and wire gauge shutter, cost of 4 mm thick plain clear glass, stainless steel wire gauge of 0.56 nominal dia of wire and average width of aperture 1.18mm, MS Grill of 12mm square bar @ 150 mm center to center and all other connected accessories. Net Opening will be measured for payment purpose. |
| 43 | Providing and fixing factory made UPVC white colour casement (Openable) glass and gauge window made of extruded profiles with wall thickness of 2.3 mm ± 0.2 mm) window profile with hollow section with multi chamber, frame (116mm x 58mm), Sash (60mm x 73mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing beads (35mm x 20mm) will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc, making arrangement for fixing of hardware EPDM gasket 1.2± 0.2 mm thick, galvanised steel frame (28mm x 21.5mm), T profile (27mm x 17mm) to be inserted in required profile. Frame will be fixed to the wall with 8mm x 100mm long fasteners, including 12 mm MS square bar @ 150 mm c/c , as grill will be provided between two shutters. Hardware Casement handle made of Zinc alloyed (white powder coated), Butt hinges of zinc alloyed (White powder coated), transmission gear made of mild steel with multi point locking system and 4 mm thick glazing with selected quality glass and stainless steel wire gauge.Note:- The unit rate quoted by contractor includes both glass and wire gauge shutter, cost of 4 mm thick plain clear glass, stainless steel wire gauge of 0.56 nominal dia of wire and average width of aperture 1.18mm, MS Grill of 12mm square bar @ 150 mm center to center and all other connected accessories. Net Opening will be measured for payment purpose) |
| 44 | M&L plain HDHMR( High Density High Moisture Resistant) solid Board ,18/19 mm thick , balancing white lamination including 1mm thick approved sunmica on external visible faces and as directed by Engr-in-charge, including pasting with solvent chemical as required at site or fixed with screws complete as in Kitchen Cupboard, room cupboard ,shelves / partition incl fixing arrangement on walls including taking down of cupboard complete all as specified and directed. |
| 45 | S&F for stainless steel modular Kitchen basket including PVC cabinet as required size for 17”x20” ht 6” for cutlery (bowl, tumbler and like) with wired bottom using 6mm rod of grade 304 stainless rod as per approved design and pattern incl necessary drawer slides of required size and chromium plated folding handles 75mm size for drawersy complete all as specified and directed |
| 46 | Description all as per item 45.00 above but with plain bottom for ht 4\\" cutlery (spoon, knife and like) complete all as specified and directed. |
| 47 | Description all as per item 45.00 above but ht 8” for plates/thali complete all as specified and directed. |
| 48 | S & F continuous piano hinges mild steel bright finish or galvanised of 40mm width of flaps for cupboard shutters complete all as specified and directed. |
| 49 | S & F SS 40 mm Cabinet Knob for cupboard shutters and kitchen cabinet and complete all as specified and directed. |
| 50 | S&F 100mm aluminium anodised hasp and staple safety type complete all as specified and directed. |
| 51 | S&F 6 mm thick toughened glass as in cabinet door incl necessary fittings like hinges handles and locking device complete all as specified and directed. |
| 52 | S&F door of Stainless steel hangers heavy duty of 6 points to hang the clothes incl all fittings and complete all as specified and directed. |
| 53 | S&F superior quality ,heavy type SS rail (grade -304) (Curtain rod/drapery rod), 20mm dia with and including fancy type SS bracket 2 Nos for each opening and SS side Knob (fancy type) of required shape and size 2 Nos of each opening complete all as specified and directed. |
| 54 | Taking up or down steel tubing and connections 15mm bore including cleaning for relaying / re-fixing or removal from site complete all as specified and directed. |
| 55 | Supply and fixing steel water tubes, medium grade, ISI marked, galvanised , 15mm bore with all fittings, tee , socket, union, flange and socket laid in trenches / on walls complete all as specified and directed. |
| 56 | Laying only old steel water tubes, any grade, galvanised, 15mm bore with all new fittings laid in trenches / on walls complete all as specified and directed. |
| 57 | Taking up or down steel tubing and connections 20mm bore including cleaning for relaying / re-fixing or removal from site complete all as specified and directed. |
| 58 | Supply and fixing steel wate tubes, medium grade, ISI marked, galvanised , 20mm bore with all fittings, tee , socket, union, flange and socket laid in trenches / on walls complete all as specified and directed. |
| 59 | Laying only old steel water tubes, any grade, galvanised, 20mm bore with all new fittings laid in trenches / on walls complete all as specified and directed. |
| 60 | S&F in repairs 15mm bore CP Bib taps Long Body Half turn/Quarter turn , cast copper alloy fancy type chromium plated and fixed complete all as specified and directed. |
| 61 | S&F in repairs 15mm bore CP Two Way Angle valve cast copper alloy fancy type chromium plated and fixed complete all as specified and directed. |
| 62 | S&F in repair 15 mm dia CP Angle Cock, cast copper alloy, screwed down, high pressure, screwed both ends for iron pipe or for unions 15mm bore all as complete all as specified and directed. |
| 63 | S& F in repair PVC connection 600 mm long 15mm dia complete all as specified and directed. |
| 64 | S&F in repair 15 mm brass chromium plated Basin Mixer single lever for WHB of any type complete all as specified and directed. |
| 65 | S&F in repairs 15mm dia 3 in 1 CP Brass wall mixture chromium plated fancy type for mixing hot and cold water screwed down for iron pipe and fixed in position complete all as specified and directed. |
| 66 | S&F in repairs 15mm sink mixture chromium plated fancy type for mixing hot and cold water screwed down for iron pipe and fixed in position complete all as specified and directed . |
| 67 | S&F in repairs vitreous China one peice wash down water closet pan (padestal pattern) including P / S trap and soft close seat cover with hinging device and CP jet spray with hanging device all necessary work required for fixed in position complete all as specified and directed. |
| 68 | S&F in repair vitreous China squatting pan \\"ORISSA\\" pattern size 580mm x 440mm, white with integral foot rest including cast iron 'P' or 'S' trap and connection to trap including cement concrete, and to flushing pipe, anti-syphonage pipe, etc. including making good to floor, complete all as specified and directed. |
| 69 | S&F in repair CP cardiff brass cascade Health Faucet with hose (Min length 1.5mtr of CP brass) & hook of CP brass complete all as specified and directed. |
| 70 | S&F in repair vitreous China wash hand basin with pedestal (Size 515x420x195mm) colour brilliant / off white including waste pipe and waste coupling over and including pedestal and all other accessories complete all as specified and directed. |
| 71 | S&F in repair 10 Litre capacity PVC valveless syphonic action type flushing cistern low level white, with inlet, ball valve, float and handle including PVC flush pipe and brackets complete fixed in wall and floor to trap of WC as required complete all as specified and directed. |
| 72 | S&F in repair Stop valves of size 15mm dia fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 73 | S&F in repair CP soap dish fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 74 | S&F in repair brass chromium plated shower rose 150mm size fitted to steel pipe or union along with leg and other fitting complete all as specified and directed. |
| 75 | S&F in repair for CP toilet roll holder fixed to wall with chromium plated brass screw completely all as specified and directed. |
| 76 | S&F in repair for toilet bath cabinet with mirror of size 600 X 450mm and approved make as per specified and directed. |
| 77 | S&F 600 x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 78 | S&F corner glass shelf 300mm (with brass brackets) complete all as specified and directed. |
| 79 | S & F in repair brass chromium plated tubular Towel Rack 600mm Long with Lower Hangers, Stainless Steel complete all as specified and directed. |
| 80 | Treatment of sunken floor slab comprises of the following specifications and complete all as specified and directed :-(i) Cleaning the sunken/lowered portion of RCC slab surface (including vertical total depth plus skirting height) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely. Provision of 40mm thick avg PCC 1:2:4 type B-0 using 12.5mm graded aggregate as in padding concrete to achieve proper slope including cutting holes in bricks or RCC wall for spout.(ii) Rendering of uneven surfaces with 6mm thick CM 1:4 mixed with and including integral water proofing compound Sika Plastocreat plus or equivalent make in Fosroc / Thremax as approved by GE @ 0.2% by wt of cement consumed including filling it with water to check dampness and seppage and where dampness / seppage is noticed, nozzles shall be fixed and grouting carried out. (iii) All junctions points of side wall where CI/GI/PVC pipes are passing through shall be sealed with epoxy putty Sikaguard 694 F(I) or equivalent make in Fosroc / Thremax as approved by GE.(iv) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean. (v) Applying two coats of polymer modified cementious water proof coating with Sika Topseal 107 or or equivalent make in Fosroc / Thremax as approved by GE in two coats @ 3kg/sqm to sanwiched with glass fibre reinforcement: Sika Fab-1 or or equivalent make in Fosroc / Thremax as approved by GE over base coat as per manufacturer's instruction to bottom and vertical sides up to finished floor level+100mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion.(vi) Plaster the bottom and sides up to bottom of the skirting with minimum 20mm thick CM 1:4 mixed with integral water proofing compound SIKA plastocreat plus or equivalent make in Fosroc / Thremax as approved by GE @ 0.2% by wt of cement consumed as per manufacturer's specification including rounding of corners and injuctions sloping towards spout. (vii) All pipes laid in sunken portion shall be covered with 50mm thick PCC 1:3:6 all round after painting with anticorrosive paint. (viii) The sunken floor shall be filled with lean concrete 1:7:12. Note :- Test the water proofed area (ponding test) by filling water for at least 72 hours and tested for leakage seepage and to the entire satisfaction of GE. Test record for each sunken slab shall be maintained. The treatment shall be carried out by authorised applicators of chemicals. Cost of testing and all M&L is inclued in the rates quoted above. |
| 81 | Supply only water proofing compound complete all as specified and directed. |
| 82 | S&F, PVC floor trap 75mm bore with grating including jointing with solvent cement fixed in cement concrete type B1 (1:2:4) complete all as specified and directed. |
| 83 | Dismantling of cast iron pipes any size of bore as in soil waste or vent pipe including removal of cement joints fixed to wall or laid in floor complete all as specified and directed. |
| 84 | S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls & floors with necessary MS clamps complete all as specified and directed. |
| 85 | S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls & floors with necessary MS clamps complete all as specified and directed. |
| 86 | S&F 110 mm PVC (SWR) access door bends any radius complete all as specified and directed. |
| 87 | S&F 75 mm PVC (SWR) access door bends any radius complete all as specified and directed. |
| 88 | S&F 110mm PVC (SWR) junction single,(Single T) equal or unequal provided with access door complete all as specified and directed. |
| 89 | S&F 75mm PVC (SWR) junction single,(Single T) equal or unequal provided with access door complete all as specified and directed. |
| 90 | S&F 110mm PVC PVC (SWR) vent cowl complete all as specified and directed. |
| 91 | Supply and fixing in repair rotional molded polyethylene water storage tank three layer white 500 ltr capacity, triple layer (Cylinderical vertical with closed top) hoisted and fixed in position including dismantling of tank complete all as specified and directed. |
| 92 | Supply and fixing in repair rotional molded polyethylene water storage tank three layer white 1000 ltr capacity, triple layer (Cylinderical vertical with closed top) hoisted and fixed in position including dismantling of tank complete all as specified and directed. |
| 93 | S&F 20mm dia ball valves high pressure of PTMTwith epoxy coated alluminium rod and high density plastic ball screwed for iron pipe and fixed complete all as specified and directed. |
| 94 | S & F in repair gun-metal, globe or gate valves of 15/20mm dia, with iron wheel head, screwed both ends for iron pipe and fixed etc complete all as specified and directed. |
| 95 | S & F in repairs, for wall mounted kitchen plate rack of size 900 x 600 x 250mm made cut of 1.00mm thick stainless steel sheet of 304A, ISI grade design as per directed by E- in- charge fixed to walls with required size of raw plug and steel screws as per manufacturer instructions . of first quality all as specified and directed. |
| 96 | S & F in repair Sinks with drainage board of size 915mm x 460mm and bowl size 410mm x 330mm x 160mm, made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 25 x 25 x 5 mm and including CP waste coupling and PVC Waste pipe of standard size complete all as specified and directed. |
| 97 | Demolition of cement concrete (un reinforced) in ground floors and paving not exc 15cm thick below or above ground level including removal of other things complete all as specified and directed. |
| 98 | M&L Brick work with burnt bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete including demolition of brickwork all as specified and directed. |
| 99 | Dismantling brick tiles in single layer on roof (laid dry and pointed) complete all as specified and directed. |
| 100 | Demolition Mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof)and removing debries out of MD land complete all as specified and directed. |
| 101 | M&L for providing cement concrete 1:2:4 type B1 (using 12.5 mm graded stone aggregate) as in roof kerbs, Roof padding finishing surface of concrete topping even and fair(without using extra cement) all as specified of average thickness in slope 1:40 over roof complete all as specified and directed. |
| 102 | M&L Screed bed or bedding layer of mortar 10mm thick in cement mortar 1:3 and finishing even and smooth with mixing of liquid WPC on roof surfaces.Note : WPC shall be measured and paid separately. |
| 103 | M&L for applying roof treatment on top of roof with APP modified membrane (minimum 3mm thick) weighing not less than 3Kg per Sqm, consisting of 90 micron center core HMHDPE (High molecular high density polyethylene) with white mineral gravel finish on upper side of membrane laid by torch application method with overlap 100 on length and 100mm on the width side as per manufacture's instructions over a coat of hot air blown grade bitumen 85/25 @ 1.20Kg/Sqm over a coat of approved cold applied bituminous oil based primer (IS-3384) @ 300 gm/sqm complete APP membrane complete all as specified and directed. |
| 104 | M& L for 75mm thick PCC 1:3:6 type C-2 (Using 20mm gradede crushed stone aggregate) as in plinth protection including mastic filling in joints complete all as specified and directed. |
| 105 | Demolition of RCC Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work and making good the disturbed area in CM 1:3 complete all as specified and directed. |
| 106 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed. Note:- Wt of stainless steel tubes shall be measured in the presence of contractor , JE & E- in- charge and recorded in the measurement book. |
| 107 | S&F in repair ,MS framed work such as grill grating,joists, framed Guard bars, barred iron doors, ladders, frame work for securing water tank, cooler stand and similar work conformed to Fe-410 or 310-0 complete all as specified and directed. |
| 108 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 109 | Providing and fixing 24 mm thick 100% solid WPC (wood polymer composite) JALI of required size and colour comprising of virgin PVC resin of K value 57-60(suspension grade) calclum carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives made from Extrusion process WPC foam sheet single extruded (inner) with density not less than 650 kg/cbm manufacture by an ISO 9001-2015 certificate company, having good screw holding capacity (screw withdrawal strength of 2000 N (face) and 1100 N (edge) minimum compressive strength of 50 n/mm2, Modulus of elasticity 850/N/mm2 and resistance of spread flame of class A category with property of being termite/borer free, water/moisture proof, fire retardant and fixing with stainless steel butt hinges/fasteners of required size with necessary full body threaded star headed counter sunk SS screws complete all as specified and directed. |
| 110 | M&L for weld-mesh of size 75x75x3mm to be wrapped on the exposed surface of rib of beam & on the slab bottom and chajjah and tack welding to the exposed reinforcement at close intervals and gunite with cement mortar 1:3 mixed with admixture SIKA Plasto create plus or equivalent make in Fosroc / Thermax as approved by GE around rib of beam or roof slab of thickness n.exc 40mm to be applied under an operating pressure. the gunited surface to be cured properly for a min of 7 days all in complete as per the technical specifications and manufacturer's instructions and complete all as specified and directed. |
| 111 | Supply and apply of rust remover cum passivator to remove rust from existing reinforcement by using Product : Rustoff-100 of Sika or equivalent make inFosroc / Thermax as approved by GE, with density : 1.01 Kg/ltr at 30°C and consumption : 0.2 kg/Sqm/coat complete all as specified and directed. Note : The material to be applied thoroughly on exposed rebars only with the help of a brush of suitable size. The area will be measured as length of bar x two times the dia of bar. |
| 112 | Supply and apply cement based polymer modified rebar corrosion protection system to existing reinforcement using cement based polymer modified rebar corrosion protection system with consumption : 3.75 kg/Sqm for two coats and product requirements: carbonation resistance : 2 mm of SikaTop Armatec®-108 of Sika or equivalent make in Fosroc / Thermax as approved by GE corresponds to 20 mm of normal mortar; bond strength > 1N/Sqmm according to ASTM C 882-78 complete all as specified and directed.Note : The material to be applied thoroughly on exposed rebars only with the help of a brush of suitable size. The area will be measured as length of bar x two times the dia of bar. |
| 113 | M&L for providing by mixing and trowel application of prepacked, light weight, two component structural grade polymer modified fibre reinforced thixotropic cement mortar Sika Monotop 122F of Sika or equivalent make in Fosroc / Thermax as approved by GE at an average thickness exceeding 10mm and upto 25mm to the prepared concrete substrate in soffit of slabs, beam, columns, parapets, fins and facias at any height, including finishing of applied Polymer mortar as per the technical specifications and manufacturer's instructions complete all as specified and directed. |
| 114 | M&L for providing by mixing and trowel application of prepacked, light weight, two component structural grade polymer modified fibre reinforced thixotropic cement mortar Sika Monotop 122F of Sika or equivalent make in Fosroc / Thermax as approved by GE at an average thickness of upto 10mm to the prepared concrete substrate in soffit of slabs, beam, columns, parapets, fins and facias at any height including finishing of applied Polymer mortar as per the technical specifications and manufacturer's instructions complete all as specified and directed. |
| 115 | M&L for RCC type B1 1:2:4 (using 20 mm graded stone aggregate) for slabs supported on walls, beams and complete all as specified and directed. |
| 116 | M&L for formwork to soffits of roof slabs & projections etc for rough finished concrete surface n exc 200 mm thick (horizontal or sloping) complete all as specified and directed. |
| 117 | Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in soft/loose soil complete all as specified and directed. |
| 118 | Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed. |
| 119 | Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed. |
| 120 | S&F 150 mm dia(6\\") reinforced concrete pipes,class NP2 with one collar per length of pipe and laid in trenches or in floors including clearing of site as per site requirement complete all as specified and directed. |
| 121 | Demolition and breaking up drain pipes (salt glazed ware or RCC or PVC) set in cement mortar 150 mm dia complete all as specified and directed. |
| 122 | M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested complete for 150mm dia pipe complete all as specified and directed. |
| 123 | Cutting into existing manholes for connecting new drains, 150mm bore, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required complete all as specified and directed. |
| 124 | High strength deformed TMT bars 6 mm and above dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed. |
| 125 | M&L for precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cover slabs for manholes (square / rectangular / circular of any type and size with Angle iron bend to shape of manhole etc, shelves and similar articles with plain faces including necessary formwork and setting in cement mortar 1:4 including necessary use and waste of formwork and demolition of existing RCC cover slabs complete all as specified and directed. |
| 126 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour,design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, including dismantling of existing paver block complete all as specified and directed. |
| 127 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed. |
| 128 | M&L for Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in coping & benching including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work, finished even and smooth using extra cement complete all as specified and directed. |
| 129 | Taking down carefully copper/Aluminium point wiring (light, fans, socket, power socket) complete including taking out existing unserviceable terminal boxes and conduit with switches/sockets/fan regulators and fittings such as ceiling roses, pendants, tube lights fittings lamp holders, brackets light fittings, rectangular blocks DB MCCB etc and making good disturbed surface of wall/ floor etc to match with the existing the surface etc complete all as specified and directed. |
| 130 | Taking down carefully copper/aluminium Submain wiring from batten /conduit from DBs,MCBs, etc) and making good to disturbed surfaces of walls, floor etc complete all as specified and directed. |
| 131 | Material and labour for point wiring with 1.5 sqmm (22/.3mm) PVC insulated and unsheathed FRLS single core multistranded copper conductor for one light/fan/bell point in and including PVC rigid non metallic new concealed conduit 19/20 mm dia medium duty, ISI marked to be terminated & including pressed modular steel boxes & cover plate of module as required on site including 1.5 sqmm (22/.3mm) PVC insulated and unsheathed FRLS single core multistranded copper earth continuity conductor controlled by one switch and/or one regulator complete including repairing the surfaces in Cm 1:3 and finishing the surface as per existing treatment all as specified and directed. |
| 132 | Description all as per item 131.00 (here-in-before) but One three pin 5 Amp socket outlet point on independent board controlled by one nos, one way switch on independent board complete all as specified and directed. |
| 133 | Description all as per item 131.00 (here-in-before) but One three pin 5 Amp socket outlet point on same board controlled by one nos, one way switch on same board complete all as specified and directed. |
| 134 | Description all as per item 131.00 above but point wiring with 2.5 sq mm single core FRLS cables and earth continuity wire with 2.5 Sq mm single core cable for one 3 pin 15 Amps socket out let point controlled by one nos, one way switch on independent board complete all as specified and directed. |
| 135 | Description all as per item 131.00 above but point wiring with 4 sq mm single core FRLS cables and earth continuity wire with 4 Sq mm single core cable for one 3 pin 15 Amps socket for AC complete all as specified and directed. |
| 136 | S&F Modular switch 1 way 6A 1 module Single pole, one way, 230 volts complete all as specified and directed. |
| 137 | S&F Modular switch 1 way 16A 1 module complete all as specified and directed. |
| 138 | S&F Modular socket 6A -2/3 pin combined 2 module type 230 volts AC complete all as specified and directed. |
| 139 | S&F Modular socket 6A/16A -2/3 pin combined 2 module type 230 Volts, AC complete all as specified and directed. |
| 140 | S&F Modular lamp holder, insulated body with back plate including LED Bulb of 9 watt suitable for batten fittings and complete all as specified and directed. |
| 141 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 142 | S&F Modular ceiling rose surface bakelite 65mm x 50mm, 3 terminals with back plate etc complete all as specified and directed. |
| 143 | Supply & fixing Modular type (1/2 module as per site requirement) ceiling fan regulator electronic step type suitable for 1200mm/1400mm sweep fan complete all as specified and directed. |
| 144 | S&F for decorative wall light stainless steel rust free fixture with white glass diffuser including 10 Watt capacity minimum filament lamp complete all as specified and directed. Make :Havells Voila wall light or equivalent make of Bajaj/Philips/Crompton. |
| 145 | S&F LED light fitting 1x20watt 4 feet long including LED tube with driver complete suitable for fixation on wall/roof with body robust, corrosion resistant, superior finish and without any crack. The fitting should have following technical specification (i) surge protection of minimum 2 KV (ii) power factor should be more than 0.90 (iii) cool white colour, (iv) total hormonic distoration (THD) should not be more than 15% (v) lumen output should not be less than 1700 lumens, (vi) can withstand with input voltage range 140-280V AC, (vii) colour rendering index should not be less than 80, (viii) Corelated colour should be minimum 6000 degree Kelvin (ix) Minimum warranty period of 2 Years. |
| 146 | S&F i Sheet metal enclosure distribution board SP&N,12way, double door powder coated, protection class IP-42 suitable for mounting MCB DBs confirming to IS-13032, IS-8632,BS5484 with min 200 Amp raiting copper bus bar complete all as specified and directed. |
| 147 | Supply and fixing MCBs SP 6 to 32Amps, 240 volts, 10 KA rupturing capacity, IS-8828 marked, of the under mentioned type and rating and fixing in DBs (DBs Catered separately in this schedule) complete all as specified and directed.Note : Make of the MCB should be the same as that of DB |
| 148 | Supply and fixing MCBs SPN 32Amps to 63 Amps, 240 volts, 10 KA rupturing capacity, IS-8828 marked, of the under mentioned type and rating and fixing in DBs (DBs Catered separately in this schedule) complete all as specified and directed.Note : Make of the MCB should be the same as that of DB |
| 149 | S&F i Sheet metal enclosure distribution board TPN,4 way, double door powder coated, protection class IP-54, isolated neutral bar, mechanical impact strength IK 09 suitable for mounting MCCB as incoming and MCB's as outgoing in DBs confirrming to IS-13032, IS-8632,BS5484 with min 200 Amp rating copper bus bar and grouting, fixing on wall with nut bolts washers proper with PCC works complete all as specified and directed . |
| 150 | Supply and fixing MCCBs FP 63 Amps, 415 volts, 16 KA rupturing capacity, IS-8828 marked, of the under mentioned type and rating and fixing in DBs (DBs Catered separately in this schedule) complete all as specified and directed.Note : Make of the MCCB should be the same as that of DB |
| 151 | Supply & fixing in replacement of Bldg security light fitting LED 30 W, pressure die cast housing epoxy powder coating IP -65, connected with and including 0.5 sqmm flexible copper multistranded conductor cable including security light bracket made to shape out of GI pipe 40 mm bore light grade, 1.5 mtr length and fixed with MS Calmps of size 40x5 mm- 02 nos ,nuts, bolts and washers on wall. complete all as specified and directed. Make Bajaj/Halonix/Orient |
| 152 | M & L for submain wiring alongwith earth wire with the 2x10.0 sq. mm +1x10.0 sq. mm earth wire sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed as required complete all as specified and directed.Note :The above mentioned specified runs of single core cables and specified runs of earth continuity conductors and the relevant conduit with accessories shall be measured as one run length. |
| 153 | Supply and fixing Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 AMP complete all as specified and directed. |
| 154 | Supply and Fixing electric water heater storage type steel body with copper inner tank and heating element upto 2KW capacity 25 Ltr. BEE 5 Star rated complete with all accessories such as safety valve, angle valve, NRV, PVC connection piece etc complete all as specified and directed. |
| 155 | Supply & Fixing BLDC type ceiling Fans complete with blades, down rods electronic regulator and accessories 230 V with minimum air delivery 245 CFM ,1200 mm sweep size , white in colour with remote control & copper winding, BEE 5 Star rated complete all as specified and directed.Make CAT Part no. HAVELLS Epic Signia and equivalent make of Bajaj/ Crompton Please Enable Macros to View BoQ information |
| 156 | Supply & Fixing BLDC type ceiling Fans complete with blades, down rods electronic regulator and accessories 230 V with minimum air delivery 245 CFM ,1200 mm sweep size , white in colour with remote control & copper winding, BEE 5 Star rated complete all as specified and directed.Make CAT Part no. HAVELLS Epic Signia and equivalent make of Bajaj/ Crompton Please Enable Macros to View BoQ information |